SEARCH · Search NASA

Results for “SDO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS2005

RAD750 SBC Usage for the Solar Dynamics Observatory (SDO) Program

This presentation focuses on the first space weather research mission in the Living with a Star (LWS) Program. The science objective of the mission is to understand the solar variations that influence life on Earth. The mission is developed and managed by NASA/GSFC with a launch date in 2008 on a five-year mission using a geosynchronous inclined orbit. Involved with the mission are three science instruments: a helloseisic and magnetic imagery (HMI), extreme ultraviolet variability experiment (EVE), and solar helispheric activity research prediction program (SHARPP). 6U qualification Vib test has been completed with successful results (no interrupts detected at 1 nanosecond). Other test result to be reported at workshop.

Li, Kenneth↗

NASA NTRS2005

USE OF THE SDO POINTING CONTROLLERS FOR INSTRUMENT CALIBRATION MANEUVERS

During the science phase of the Solar Dynamics Observatory mission, the three science instruments require periodic instrument calibration maneuvers with a frequency of up to once per month. The command sequences for these maneuvers vary in length from a handful of steps to over 200 steps, and individual steps vary in size from 5 arcsec per step to 22.5 degrees per step. Early in the calibration maneuver development, it was determined that the original attitude sensor complement could not meet the knowledge requirements for the instrument calibration maneuvers in the event of a sensor failure. Because the mission must be single fault tolerant, an attitude determination trade study was undertaken to determine the impact of adding an additional attitude sensor versus developing alternative, potentially complex, methods of performing the maneuvers in the event of a sensor failure. To limit the impact to the science data capture budget, these instrument calibration maneuvers must be performed as quickly as possible while maintaining the tight pointing and knowledge required to obtain valid data during the calibration. To this end, the decision was made to adapt a linear pointing controller by adjusting gains and adding an attitude limiter so that it would be able to slew quickly and still achieve steady pointing once on target. During the analysis of this controller, questions arose about the stability of the controller during slewing maneuvers due to the combination of the integral gain, attitude limit, and actuator saturation. Analysis was performed and a method for disabling the integral action while slewing was incorporated to ensure stability. A high fidelity simulation is used to simulate the various instrument calibration maneuvers.

Vess, Melissa F.↗

NASA NTRS2007

SDO Delta H Mode Design and Analysis

While on orbit, disturbance torques on a three axis stabilized spacecraft tend to increase the system momentum, which is stored in the reaction wheels. Upon reaching the predefined momentum capacity (or maximum wheel speed) of the reaction wheel, an external torque must be used to unload the momentum. The purpose of the Delta H mode is to manage the system momentum. This is accomplished by driving the reaction wheels to a target momentum state while the attitude thrusters, which provide an external torque, are used to maintain the attitude. The Delta H mode is designed to meet the mission requirements and implement the momentum management plan. Changes in the requirements or the momentum management plan can lead to design changes in the mode. The momentum management plan defines the expected momentum buildup trend, the desired momentum state and how often the system is driven to the desired momentum state (unloaded). The desired momentum state is chosen based on wheel capacity, wheel configuration, thruster layout and thruster sizing. For the Solar Dynamics Observatory mission, the predefined wheel momentum capacity is a function of the jitter requirements, power, and maximum momentum capacity. Changes in jitter requirements or power limits can lead to changes in the desired momentum state. These changes propagate into the changes in the momentum management plan and therefore the Delta H mode design. This paper presents the analysis and design performed for the Solar Dynamics Observatory Delta H mode. In particular, the mode logic and processing needed to meet requirements is described along with the momentum distribution formulation. The Delta H mode design is validated using the Solar Dynamics Observatory High Fidelity simulator. Finally, a summary of the design is provided along with concluding remarks.

Mason, Paul A.↗

NASA NTRS2008

Solar Dynamics Observatory (SDO) HGAS Induced Jitter

This paper presents the results of a comprehensive assessment of High Gain Antenna System induced jitter on the Solar Dynamics Observatory. The jitter prediction is created using a coupled model of the structural dynamics, optical response, control systems, and stepper motor actuator electromechanical dynamics. The paper gives an overview of the model components, presents the verification processes used to evaluate the models, describes validation and calibration tests and model-to-measurement comparison results, and presents the jitter analysis methodology and results.

Liu, Alice↗

NASA NTRS2010

Solar Flare Impulsive Phase Observations from SDO and Other Observatories

With the start of normal operations of the Solar Dynamics Observatory in May 2010, the Extreme ultraviolet Variability Experiment (EVE) and the Atmospheric Imaging Assembly (AIA) have been returning the most accurate solar XUV and EUV measurements every 10 and 12 seconds, respectively, at almost 100% duty cycle. The focus of the presentation will be the solar flare impulsive phase observations provided by EVE and AIA and what these observations can tell us about the evolution of the initial phase of solar flares. Also emphasized throughout is how simultaneous observations with other instruments, such as RHESSI, SOHO-CDS, and HINODE-EIS, will help provide a more complete characterization of the solar flares and the evolution and energetics during the impulsive phase. These co-temporal observations from the other solar instruments can provide information such as extending the high temperature range spectra and images beyond that provided by the EUV and XUV wavelengths, provide electron density input into the lower atmosphere at the footpoints, and provide plasma flows of chromospheric evaporation, among other characteristics.

Chamberlin, Phillip C.↗

NASA NTRS2011

SDO and RHESSI Observations of Microflares

We present observations of 100 flares (B and A GOES Class) with simultaneous observations in both hard X-ray (HXR) and ultraviolet (UV/EUV) observations by RHESSI and SDO/AIA, respectively. The micro flares were chosen by visually searching for time-isolated events in the available concurrent RHESSI/SDO dataset. Identifying the flare region using RHESSI imaging observations, we compare HXR (thermal and nonthermal) light curves and images with those observed by AlA in every available UV/EUV channels. Many events show complex morphologies with multiple flaring loops observed in AlA images. For the simplest event with a single flare loop, good correlation is found between the hot thermal (approx.10 MK) HXR emission and emission from 131 and 94 Angstrom and the filter-ratio derived temperatures agree with the HXR-derived temperatures during the decay phase. During the impulsive phase, footpoints emission was observed at all wavelengths with filter-ratios suggest the presence of multiple temperatures.

Christe, Steven D.↗

NASA NTRS2012

Evidence for Widespread Cooling in an Active Region Observed with the SDO Atmospheric Imaging Assembly

A well known behavior of EUV light curves of discrete coronal loops is that the peak intensities of cooler channels or spectral lines are reached at progressively later times. This time lag is understood to be the result of hot coronal loop plasma cooling through these lower respective temperatures. However, loops typically comprise only a minority of the total emission in active regions. Is this cooling pattern a common property of active region coronal plasma, or does it only occur in unique circumstances, locations, and times? The new SDO/AIA data provide a wonderful opportunity to answer this question systematically for an entire active region. We measure the time lag between pairs of SDO/AIA EUV channels using 24 hours of images of AR 11082 observed on 19 June 2010. We find that there is a time-lag signal consistent with cooling plasma, just as is usually found for loops, throughout the active region including the diffuse emission between loops for the entire 24 hour duration. The pattern persists consistently for all channel pairs and choice of window length within the 24 hour time period, giving us confidence that the plasma is cooling from temperatures of greater than 3 MK, and sometimes exceeding 7 MK, down to temperatures lower than approx. 0.8 MK. This suggests that the bulk of the emitting coronal plasma in this active region is not steady; rather, it is dynamic and constantly evolving. These measurements provide crucial constraints on any model which seeks to describe coronal heating.

Viall, Nicholeen M.↗

NASA NTRS2013

Observations from Hinode and SDO of a Twisting and Writhing Start to a Solar-filament-eruption Cascade

Active region eruption of 1 June 2011. Ejective eruption. GOES class C4.1 flare. SDO/AIA, various filters (94, 131, 171, 193, 211, 304, 335 Ang.) High time cadence (24 s) and high spatial resolution (0 .6 pixels). SDO/HMI line-of-sight magnetograms. Hinode observed the onset, and the later decay phase. There are two filament eruptions (filament 1 and filament 2). Filament 1 has slow rise with steps, as in several previous cases. GOES "episodes" play role of "microflares" in other events; that is, filament jumps <=> intensity peaks. Episode 1 brightening: Accompanied by filament 1 s initial motions. (Rest of talk.) Filament 1 becomes unstable, and.. Episode 2 brightening: Flare ribbons following filament 1 s fast liftoff. This destabilizes neighboring filament 2, and... Episode 3 brightening: Flare ribbons of whole system following filament 2 s eruption.Something leads to reconnection; not totally clear what. Reconnection -> twisted flux rope in approx.20 min; episode 1 microflare (flare ribbons; TC) and filament jump. Twist -> writhe, via kink instability; filament-trajectory plateau, approx. 20 min. Writhe -> jump and eruption of filament 1, via instability; episode 2 microflare (flare ribbons; TC). (E.g., Williams et al.) First eruption -> second filament eruption (episode 3 flare ribbons; TC). (E.g., Sterling, Moore; Liu et al.; Torok et al.; Schrijver & Title.). Estimate amount of free energy in newly-twisted field (cf. Moore 1988): where we have taken L and r = 50, 3 arcsec. Energy of the total system is likely 1030 ergs or more. So "no" is answer to question. Additional energy comes from remainder of sheared large loop, shear (free energy) of second filament, etc. (Normally assumed situation.) Some history of twist-induced instability in filament eruptions: e.g., Sakurai, Torok & Kliem, Fan & Gibson, Gilbert et al., van Driel-Gesztelyi et al. Criterion : Kink instability for line-tied tube (Hood & Priest): 2.5pi; for Titov & Demoulin loop (Torok et al): approx.3.5pi We observe here: approx.1.5 turns (3.0pi) over ~50. => consistent with kink instability acting. (Cf. Srivastava et al. (2010): Small flare seen in TRACE and Hinode: approx.6.0pi)

Sterling, Alphonse C.↗

NASA NTRS2013

Evidence of Nanoflare Heating in Coronal Loops Observed with Hinolde-XRT and SDO-AIA

We study a series of coronal loop lightcurves from X-ray and EUV observations. In search for signatures of nanoflare heating, we analyze the statistical properties of the observed lightcurves and compare them with synthetic cases obtained with a 2D cellular-automaton model based on nanoflare heating driven by photospheric motions. Our analysis shows that the observed and the model lightcurves have similar statistical properties. The asymmetries observed in the distribution of the intensity fluctuations indicate the possible presence of widespread cooling processes in sub-resolution magnetic strands.

Lopez-Fuentes, M. C.↗

NASA NTRS2012

Using Sdo's AIA to Investigate Energy Transport from a Flare's Energy Release Site to the Chromosphere

Coordinated observations of a GOES B4.8 microflare with SDOs Atmospheric Imaging Assembly (AIA) and the RamatyHigh Energy Solar Spectroscopic Imager (RHESSI) on 2010 July 31 show that emission in all seven of AIAs EUV channels brightened simultaneously nearly 6 min before RHESSI or GOES detected emission from plasma at temperatures around 10 MK. Aims. To help interpret these and AIA flare observations in general, we characterized the expected temporal responses of AIAs 94, 131, 171, 193, 211, and 335 channels to solar flare brightenings by combining (1) AIAs nominal temperature response functions available through SSWIDL with (2) EUV spectral line data observed in a flare loop Coordinated observations of a GOES B4.8 microflare with SDOs Atmospheric Imaging Assembly (AIA) and the RamatyHigh Energy Solar Spectroscopic Imager (RHESSI) on 2010 July 31 show that emission in all seven of AIAs EUV channels brightenedsimultaneously nearly 6 min before RHESSI or GOES detected emission from plasma at temperatures around 10 MK.Aims. To help interpret these and AIA flare observations in general, we characterized the expected temporal responses of AIAs 94,131, 171, 193, 211, and 335 channels to solar flare brightenings by combining (1) AIAs nominal temperature response functionsavailable through SSWIDL with (2) EUV spectral line data observed in a flare loop

Solar X-rays↗

NASA NTRS2012

Erratum: SDO-AIA Observation of Kelvin-helmholtz Instability in the Solar Corona

The first SDOAIA observation of the KelvinHelmholtz instability in the solar corona in the 2010 April 8 event was reported by Ofman Thompson (2010, 2011). Foullon et al. (2011), which was published prior to Ofman Thompson (2011), claimed the detection of the KelvinHelmholtz instability in a later event (2010 November 3), and should have been cited in Ofman Thompson (2011).

Kelvin-helmholtz instability↗

NASA NTRS2012

Quasi-periodic Fast-mode Wave Trains Within a Global EUV Wave and Sequential Transverse Oscillations Detected by SDO-AIA

We present the first unambiguous detection of quasi-periodic wave trains within the broad pulse of a global EUV wave (so-called EIT wave) occurring on the limb. These wave trains, running ahead of the lateral coronal mass ejection (CME) front of 2-4 times slower, coherently travel to distances greater than approximately solar radius/2 along the solar surface, with initial velocities up to 1400 kilometers per second decelerating to approximately 650 kilometers per second. The rapid expansion of the CME initiated at an elevated height of 110 Mm produces a strong downward and lateral compression, which may play an important role in driving the primary EUV wave and shaping its front forwardly inclined toward the solar surface. The wave trains have a dominant 2 minute periodicity that matches the X-ray flare pulsations, suggesting a causal connection. The arrival of the leading EUV wave front at increasing distances produces an uninterrupted chain sequence of deflections and/or transverse (likely fast kink mode) oscillations of local structures, including a flux-rope coronal cavity and its embedded filament with delayed onsets consistent with the wave travel time at an elevated (by approximately 50%) velocity within it. This suggests that the EUV wave penetrates through a topological separatrix surface into the cavity, unexpected from CME-caused magnetic reconfiguration. These observations, when taken together, provide compelling evidence of the fast-mode MHD wave nature of the primary (outer) fast component of a global EUV wave, running ahead of the secondary (inner) slow component of CME-caused restructuring.

Solar Corona↗

NASA NTRS2014

Analysis of Inter-Moss Loops in the Solar Region with IRIS and SDO AIA: Automatic Event Detection and Characterization

The Interface Region Imaging Spectrograph (IRIS), launched in the summer of 2013, is designed specifically to observe and investigate the transition region and adjacent layers of the solar atmosphere, obtaining images in high spatial, temporal, and spectral resolution. Our particular work is focused on the evolution of inter-moss loops, which have been detected in the lower corona by the Atmospheric Imaging Assembly (AIA) and the High-Resolution Coronal Imager (Hi- C), but are known to have foot points below the transition region. With the high-resolution capabilities of IRIS and its Si IV pass band, which measures activity in the upper chromosphere, we can study these magnetic loops in detail and compare their characteristic length and time scales to those obtained from several AIA image sets, particularly the 171, 193, and 211 pass bands. By comparing the results between these four data sets, one can potentially establish a measure of the ionization equilibrium for the location in question. To explore this idea, we found a large, sit-and-stare observation within the IRIS database that fit our specifications. This data set contained a number of well-defined inter-moss loops (by visual inspection) with a cadence less than or equal to that of AIA (approximately 12 seconds). This particular data set was recorded on October 23, 2013 at 07:09:30, lasting for 3219 seconds with a field of view of 120.6 by 128.1 arcseconds, centered on -53.9 by 59.1 arcseconds from disk center. For ease of comparison, the AIA data has been interpolated to match the IRIS cadence and resolution. In the main portion of the poster, we demonstrate the detection of events, the information collected, and the immediate results to the right, showing the progress of an event with green as the start, blue as the peak, and red as the end. Below here, we demonstrate how pixels are combined to form groups. The 3D results are shown to the right.

event detection↗

NASA NTRS2015

Center-to-Limb Variation of Deprojection Errors in SDO HMI Vector Magnetograms

No abstract available

Magnetograms↗

NASA NTRS2015

Modeling a Full Coronal Loop Observed with Hinode EIS and SDO AIA

Physical parameters measured from an observation of a coronal loop from Gupta et al. (2015) using Hinode/EIS and SDO/AIA were used as input for the hydrodynamic, impulsively heating NRLSOFM 1-d loop model. The model was run at eight different energy inputs and used the measured quantities of temperature (0.73 MK), density (10(sup 8.5)cm(sup -3) and minimum loop lifetime to evaluate the success of the model at recreating the observations. The loop was measured by us to have an unprojected length of 236 Mm and was assumed to be almost perpendicular to the solar surface (tilt of 3.5 degrees) and have a dipolar geometry. Our results show that two of our simulation runs (with input energies of 0.01 and 0.02 ergs cm(sup -3)S(sup -1) closely match the temperature/density combination exhibited by the loop observation. However, our simulated loops only remain in the temperature sensitive region of the Mg 278.4 Angstrom filter for 500 and 800 seconds respectively which is less than the 1200 seconds that the loop is observed for with EIS in order to make the temperature/density measurements over the loop's entire length. This leads us to conclude that impulsive heating of a single loop is not complex enough to explain this observation. Additional steady heating or a collection of additional strands along the line-of-sight would help to align the simulation with the observation.

coronal loop↗

NASA NTRS2016

Analysis of Inter-Moss Loops in the Solar Region with IRIS and SDO AIA: Automatic Event Detection and Characterization

IRIS↗

NASA NTRS2014

SDO and STEREO Observations of Prominence Dynamics During a Series of Eight Homologous Flares

Homologous flares are eruptive events that occur repetitively in the same active region, with similar structure and morphology. A series of at least eight homologous flares occurred in active region NOAA 11237 over 16 - 17 June 2011. A filament is rooted in the active region with an overlying coronal cavity. The active region appears on the southeast solar limb as seen from SDO/AIA, and on the disk as viewed from STEREO-B/EUVI; the dual perspective allows us to study in detail behavior of prominence/filament material entrained in the magnetic field of the repeatedly-erupting system. Each of the eruptions was mainly confined, with active-region prominence material being ejected from the core of the erupting region onto outer-lobe loops of the active region. The eruption series repeatedly disrupted material of a quiet-Sun extension of the prominence, and that material became suspended at progressively higher heights above the surface. Two final eruptions from the core region destabilized the field holding that material, instigating a coronal mass ejection (CME).

homologous flares↗

NASA NTRS2018

IRIS and SDO Observations of Solar Jetlets Resulting from Flux Cancelation

Jets of all sizes are frequent magnetically channeled narrow eruptions. They occur in various solar environments: quiet regions, coronal holes and active regions. All coronal jets observed in UV, EUV and X-ray images show a bright spire with a base brightening, also known as jet bright point (JBP). Recent studies show that coronal jets are driven by small-scale filament eruptions. We found in on disk quiet regions and coronal holes that coronal jets originate at a neutral line between dominant-polarity flux and a patch of canceling minority-polarity flux.

Panesar, Navdeep K.↗