Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERED INTERFACES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Elucidating the role of earth alkaline doping in perovskite-based methane dry reforming catalysts

To elucidate the role of earth alkaline doping in perovskite-based dry reforming of methane (DRM) catalysts, we embarked on a comparative and exemplary study of a Ni-based Sm perovskite with and without Sr doping. While the Sr-doped material appears as a structure-pure Sm 1.5 Sr 0.5 NiO 4 Ruddlesden Popper structure, the undoped material is a NiO/monoclinic Sm 2 O 3 composite. Hydrogen pre-reduction or direct activation in the DRM mixture in all cases yields either active Ni/Sm 2 O 3 or Ni/Sm 2 O 3 /SrCO 3 materials, with albeit different short-term stability and deactivation behavior. The much smaller Ni particle size after hydrogen reduction of Sm 1.5 Sr 0.5 NiO 4 , and of generally all undoped materials stabilizes the short and long-term DRM activity. Carbon dioxide reactivity manifests itself in the direct formation of SrCO 3 in the case of Sm 1.5 Sr 0.5 NiO 4 , which is dominant at high temperatures. For Sm 1.5 Sr 0.5 NiO 4 , the CO : H 2 ratio exceeds 1 at these temperatures, which is attributed to faster direct carbon dioxide conversion to SrCO 3 without catalytic DRM reactivity. As no Sm 2 O 2 CO 3 surface or bulk phase as a result of carbon dioxide activation was observed for any material – in contrast to La 2 O 2 CO 3 – we suggest that oxy-carbonate formation plays only a minor role for DRM reactivity. Rather, we identify surface graphitic carbon as the potentially reactive intermediate. Graphitic carbon has already been shown as a crucial reaction intermediate in metal-oxide DRM catalysts and appears both for Sm 1.5 Sr 0.5 NiO 4 and NiO/monoclinic Sm 2 O 3 after reaction as crystalline structure. It is significantly more pronounced for the latter due to the higher amount of oxygen-deficient monoclinic Sm 2 O 3 facilitating carbon dioxide activation. Despite the often reported beneficial role of earth alkaline dopants in DRM catalysis, we show that the situation is more complex. In our studies, the detrimental role of earth alkaline doping manifests itself in the exclusive formation of the sole stable carbonated species and a general destabilization of the Ni/monoclinic Sm 2 O 3 interface by favoring Ni particle sintering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Research on the interfacial structure and property improvement of the Cfiber/2Si-B-3C-N ceramic matrix composite

Highlights: • The C{sub fiber}/2Si-B-3C-N composite with nice properties was successfully prepared. • ZrO{sub 2} promotes the densification process, homogeneous nucleation and grain growth. • The interface reaction in the composite was well controlled by the addition of ZrO{sub 2}. • The damage to carbon fiber was largely avoided by the addition of ZrO{sub 2}. - Abstract: A mixture of the mechanically alloyed 2Si-B-3C-N powder and short carbon fiber was hot pressed at 1800 °C for 30 mins in nitrogen. Careful investigation to the prepared C{sub fiber}/2Si-B-3C-N ceramic matrix composite revealed that the composite was very difficult to be densified. Heterogeneous nucleation, abnormal grain growth and severe interface reaction occurred on the fiber surface or between the fiber and the ceramic matrix, leading to a small density and weak mechanical properties of the composite. For the prepared composite without any additive, the relative density, flexural strength, elastic modulus and fracture toughness is 71.7%, 64.6 MPa, 14.7 GPa and 1.47 MPa·m{sup 1/2}, respectively. The average size of the SiC grains close to and far away from the carbon fiber is 249.10 nm and 50.45 nm, respectively. However, with the addition of ZrO{sub 2} (7.5 mol%), the above mentioned phenomenons are changed noticeably, and those properties are significantly increased to 88.5%, 112.4 MPa, 111.1 GPa and 2.94 MPa·m{sup 1/2}, respectively. At the same time, the SiC grains close to or far away from the carbon fiber almost have the same average size of about 448.21 nm, and almost no interface reaction occurs. It shows that the addition of ZrO{sub 2} not only facilitates the sintering and densification process, but also depresses the interface reaction, promotes the homogeneous nucleation and grain growth, and hence significantly improves the mechanical properties of the C{sub fiber}/2Si-B-3C-N composite. This interesting finding is favorable for the preparation of carbon fiber reinforced ceramic matrix composite, which requires both a large relative density and well controlled interface reaction.

36 MATERIALS SCIENCE↗

Stress Intensity of Delamination in a Sintered-Silver Interconnection: Preprint

In automotive power electronics packages, conventional thermal interface materials such as greases, gels, and phase-change materials pose bottlenecks to heat removal and are also associated with reliability concerns. The industry trend is toward high thermal performance bonded interfaces for large-area attachments. However, because of coefficient of thermal expansion mismatches between materials/layers and resultant thermomechanical stresses, adhesive and cohesive fractures could occur, posing a reliability problem. These defects manifest themselves in increased thermal resistance. This research aims to investigate and improve the thermal performance and reliability of sintered-silver for power electronics packaging applications. This has been experimentally accomplished by the synthesis of large-area bonded interfaces between metalized substrates and copper base plates that have subsequently been subjected to thermal cycles. A finite element model of crack initiation and propagation in these bonded interfaces will allow for the interpretation of degradation rates by a crack-velocity (V)-stress intensity factor (K) analysis. A description of the experiment and the modeling approach are discussed.

30 DIRECT ENERGY CONVERSION↗

Deep Understanding of Strong Metal Interface Confinement: A Journey of Pd/FeO x Catalysts

Tuning the atomic interface configuration of noble metals (NMs) and transition-metal oxides is an effective straightforward yet challenging strategy to modulate the activity and stability of heterogeneous catalysts. Herein, Pd supported on mesoporous Fe 2 O 3 with a high specific surface area was rationally designed and chosen to construct the Pd/iron oxide interface. As a versatile model, the physicochemical environments of Pd nanoparticles (NPs) could be precisely controlled by taming the reduction temperature. The experimental and density functional theory calculation results unveiled that the catalyst in the support–metal interface confinement (SMIC) state showed significantly enhanced catalytic activity and sintering resistance for CO oxidation. The constructed Fe sites at the interfaces between FeO x overlayers and Pd NPs not only provided additional coordinative unsaturated ferrous sites for the adsorption and activation of O 2 , thereby facilitating the activation efficiency of O 2 , but also impressively changed the reaction pathway of CO oxidation. As a result, the catalyst followed the Pd/Fe dual-site mechanism instead of the classical Mars–van Krevelen mechanism. For the catalyst in the strong metal–support interaction (SMSI) state, its catalytic activity was seriously suppressed because of the excessive encapsulation of the active Pd sites by FeO x overlayers. Thus, the present study therefore provides detailed insights into the SMIC and SMSI in ferric oxide-supported Pd catalysts, which could guide the preparation of highly efficient supported catalysts for practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Performance and Reliability of Bonded Interfaces for High-Temperature Packaging (Presentation)

The thermal performance and reliability of sintered-silver is being evaluated for power electronics packaging applications. This will be experimentally accomplished by the synthesis of large-area bonded interfaces between metalized substrates that will be subsequently subjected to thermal cycles. A finite element model of crack initiation and propagation in these bonded interfaces will allow for the interpretation of degradation rates by a crack-velocity (V)-stress intensity factor (K) analysis. The experiment is outlined, and the modeling approach is discussed.

30 DIRECT ENERGY CONVERSION↗

Correlation between dielectric breakdown strength and interface polarization in barium strontium titanate glass ceramics

The correlation between the dielectric breakdown performance and interface polarization was studied by the measurements of the dielectric breakdown strength and impedance spectroscopy as a function of sintering temperatures in a BaO-SrO-TiO{sub 2}-Al{sub 2}O{sub 3}-SiO{sub 2} glass ceramic system. It was found that dielectric breakdown strength strongly depends on the interface polarization. The sintering temperature dependence of breakdown strength is attributed to the variation in interfacial polarization based on the results of complex impedance analysis.

36 MATERIALS SCIENCE↗

Interfacial engineering via laser ablation for high-performing PEM water electrolysis

A rationalized interfacial design strategy was applied to tailor the porous transport layer (PTL)-catalyst layer (CL) contact and the PTL bulk-phase architecture. Particularly, at the PTL-CL interface, our results reveal that laser ablated sintered titanium power-based PTLs improve electrolyzer performance at both the H2NEW Consortium baseline catalyst loading of 0.4 mgIr cm -2 as well as at the ultra-low catalyst loading of 0.055 mgIr cm -2 . Under ultra-low catalyst loadings, the laser ablated PTL demonstrates maximum reduction of 230 mV compared to the commercial PTL at 4 A cm -2 , and reduces by 68 mV at 3.2 A cm -2 under H2NEW baseline loading. Laser ablation alters the titanium phase at the interface, so it forms more uniform structure like a microporous layer or a backing layer, leading to an increase in the surface area in contact with the catalyst layer while preventing the membrane from deforming into the PTL. Moreover, we reveal that bulk-phase architecture modification of the PTL by ablating patterned pores at the flow field-PTL interface improves mass transport without sacrificing contact at the CL-PTL interface. Overall, laser ablation of the PTL is an effective method to customize interfacial design to enhance proton exchange membrane electrolyzer performance.

08 HYDROGEN↗

Avoiding CO 2 Improves Thermal Stability at the Interface of Li 7 La 3 Zr 2 O 12 Electrolyte with Layered Oxide Cathodes

Abstract Solid‐state batteries promise higher energy densities and better safety than Li‐ion batteries with liquid electrolytes. However, the interface between solid electrolyte and cathode is unstable at the elevated temperatures that are needed while sintering to achieve good bonding between ceramic components. Here, the hypothesis is that, the gas environment, especially the presence of CO 2, is critical in determining the stability of the solid electrolyte–cathode interface. The effect of gas species on the interface is systematically probed, by a using Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte with a thin film LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode as a model system to enable interface sensitivity. Detrimental phases formed at the interface and their onset conditions are identified by X‐ray absorption spectroscopy, X‐ray diffraction, and Gibbs free energy analysis. As a result, removing CO 2 and minimizing H 2 O(g) during sintering is necessary to obtain good contact at the LLZO|cathode interface without forming secondary phases. Sintering in O 2 is ideal, yielding excellent chemical stability and low interfacial resistance. Secondary phases also do not form in N 2, but oxygen loss occurs at elevated temperatures. The interfacial resistance obtained upon sintering in pure O 2 is comparable to the lowest values at LLZO interfaces with protective coatings, but here without the need for interface coatings.

25 ENERGY STORAGE↗

Power Electronics Materials and Bonded Interfaces - Reliability and Lifetime

The emergence of wide-bandgap (WBG) devices in power electronics packages has brought significant attention to the reliability and thermal performance of the bonded interfaces. These interfaces, such as die-attach and substrate-attach, need to withstand the severe stress induced on them by the high-temperature (> 200°C) operation of the WBG devices. Sintered silver and transient liquid phase alloys are key bonded interfaces that can enable the high-temperature operation of WBG devices, however it is essential to evaluate their reliability and study the possible failure mechanisms before they can be used in power electronics packages. Sintered silver is already being adopted in commercial packages as a die-attach, but large-area substrate-attach offers additional reliability challenges. In this project, we investigate the reliability of these interface materials under accelerated thermal cycling and correlate these results with finite element simulations to develop lifetime prediction models. The failure mechanisms of these bonded interfaces are also studied.

47 OTHER INSTRUMENTATION↗

Power Electronics Materials and Bonded Interfaces - Reliability and LIfetime

The emergence of wide-bandgap (WBG) devices in power electronics packages has brought significant attention to the reliability and thermal performance of the bonded interfaces. These interfaces, such as die-attach and substrate-attach, need to withstand the severe stress induced on them by the high-temperature (> 200 degrees C) operation of the WBG devices. Sintered silver and transient liquid phase alloys are key bonded interfaces that can enable the high-temperature operation of WBG devices, however it is essential to evaluate their reliability and study the possible failure mechanisms before they can be used in power electronics packages. Sintered silver is already being adopted in commercial packages as a die-attach, but large-area substrate-attach offers additional reliability challenges. In this project, we investigate the reliability of these interface materials under accelerated thermal cycling and correlate these results with finite element simulations to develop lifetime prediction models. The failure mechanisms of these bonded interfaces are also studied.

33 ADVANCED PROPULSION SYSTEMS↗

Development of Multilayer Sinter Cladding of Cold Work Tool Steel on Hadfield Steel Plates for Wear-Resistant Applications

Machinery components used for mining and mineral processing activities are often subjected to high impact loads and wear which have placed demands for the development of materials with high resistance to dynamic loads and aggressive wear conditions. In this study, a multilayered cladding of high alloyed cold work tool steel (X245VCrMo9-4), interlayered with Hadfield steel (X120Mn12) plates, which was also used as substrate using super-solidus liquid-phase sintering technique was investigated. A stack of the cold work tool steel powder was prepared with interlayered X120Mn12 steel plates in an alumina crucible at tap density with the substrate placed on it and was sintered in a vacuum furnace at 1250 °C at a heating rate of 10 K/min, held for 30 min under a nitrogen atmosphere at 0.08 MPa and furnace-cooled. Sample from the as-sintered cladding was subjected to austenization at 1000 °C, quenched in oil and tempered at 150 °C for 2 h. Samples were subjected to microstructural examination using optical and scanning electron microscopy. The microstructural investigations were supplemented by hardness and impact wear tests. Computational thermodynamics was used to support experimental findings. The results revealed that a near-net densification of the sintered X245 was achieved with 99.93 ± 0.01% density. The sintered X245 was characterized by a dispersion of vanadium carbonitride precipitates, especially at the grain boundaries. The heat-treated X245 sample had the highest hardness of 680 ± 7 HV30 due to the matrix of tempered martensitic microstructure when compared to as-sintered with hardness of 554 ± 2 HV30. The X245/X120 interface was characterized by diffusion of Cr, Mo, Mn and C, which resulted in metallurgical bonding between the cladded materials. The impact wear resistance of the sintered X245 was eight times that of the X120; hence, a tough and wear-resistant tool is anticipated when the X120 work hardened in service.

36 MATERIALS SCIENCE↗

A New Approach to Joining Dissimilar Ceramic Oxides for Chemical Sensors

Conventional joining of dissimilar oxides for sensing electrodes (SE) of chemical sensors has been pivotal to the development of various sensors and is vital to their further development. However, it is shown that the uncertainty (of a fundamental nature) in the properties of dissimilar oxides in SE causes the determination of their sensing characteristics to be ambiguous. Characteristics are different for such controlled parameters as pyrolysis temperature, crystal structure, particle's morphology and size, chemical and phase composition, the coefficient of thermal expansion (CTE), surface architecture, the bulk and surface stoichiometry and type and conductivity of additives. Here, we provide an alternative approach for joining dissimilar metal-oxides for chemical sensors SE. The approach relies on the development of at least one transient liquid oxide phase on the ceramic-SE interface. These results constitute key points relevant to selection oxides for joining, sintering temperatures and heating/cooling temperature rates.

36 MATERIALS SCIENCE↗

Enhanced activity and stability of MgO-promoted Ni/Al 2 O 3 catalyst for dry reforming of methane: Role of MgO

Highly dispersed nickel nanoparticles (NPs) were deposited on Al 2 O 3 NPs by atomic layer deposition (ALD). Various amounts of MgO were loaded on Ni/Al 2 O 3 catalysts by the incipient wetness (IW) method for dry reforming of methane. Fresh and used catalysts were systematically characterized to reveal the effects of MgO on the catalytic performance. MgO was found to increase the basic amount and basic strength of catalyst surfaces, which provided additional surface oxygen species and assisted the adsorption and activation of CO 2 . Although the formation of NiO-MgO solid solution, during the calcination of incipient wetness, did not improve the overall reducibility, the Ni NPs from NiO-MgO solid solution after reduction formed an intimate interaction with MgO, which could inhibit Ni NPs from sintering and provide sufficient metal-support interface for CO 2 activation. The MgO-promoted Ni/Al 2 O 3 reached a methane reforming rate of 1780 L CH4 g Ni -1 h -1 at 850 °C, which is 26% more than that of the pristine Ni/Al 2 O 3 . Finally, the higher CO 2 activity enhanced the oxidation rate of the surface carbon generated from side-reactions, thereby resulting in a higher reforming rate and inhibiting coke formation, especially the detrimental graphitic encapsulating carbon on the active nickel surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Engineering Two-Phase and Three-Phase Microstructures from Water-Based Dispersions of Nanoparticles for Eco-Friendly Polymer Solar Cell Applications

Nanoparticle organic photovoltaics, a subfield of organic photovoltaics (OPV), has attracted increasing interest in recent years due to the eco-friendly fabrication of solar modules afforded by colloidal ink technology. Importantly, using this approach it is now possible to engineer the microstructure of the light absorbing/charge generating layer of organic photovoltaics; decoupling film morphology from film deposition. In this study, single-component nanoparticles of poly(3-hexylthiophene) (P3HT) and phenyl-C 61 butyric acid methyl ester (PC 61 BM) were synthesized and used to generate a two-phase microstructure with control over domain size prior to film deposition. Scanning transmission X-ray microscopy (STXM) and electron microscopy were used to characterize the thin film morphology. Uniquely, the measured microstructure was a direct input for a nanoscopic kinetic Monte Carlo (KMC) model allowing us to assess exciton transport properties that are experimentally inaccessible in these single-component particles. Photoluminescence, UV-vis spectroscopy measurements, and KMC results of the nanoparticle thin films enabled the calculation of an experimental exciton dissociation efficiency (η ED ) of 37% for the two-phase microstructure. The glass transition temperature (T g ) of the materials was characterized with dynamic mechanical thermal analysis (DMTA) and thermal annealing led to an increase in ηED to 64% due to an increase in donor-acceptor interfaces in the thin film from both sintering of neighboring opposite-type particles in addition to the generation of a third mixed phase from diffusion of PC 61 BM into amorphous P3HT domains. Finally, this study demonstrates the higher level of control over donor-acceptor film morphology enabled by customizing nanoparticulate colloidal inks, where the optimal three-phase film morphology for an OPV photoactive layer can be designed and engineered.

36 MATERIALS SCIENCE↗

Power Electronics Thermal Control (Presentation)

Thermal management plays an important part in the cost of electric drives in terms of power electronics packaging. Very promising results have been obtained by using microporous coatings and skived surfaces in conjunction with single-phase and two-phase flows. Sintered materials and thermoplastics with embedded fibers show significant promise as thermal interface materials, or TIMs. Appropriatecooling technologies depend on the power electronics package application and reliability.

33 ADVANCED PROPULSION SYSTEMS↗

Thermomechanical Degradation of Sintered Copper Under High-Temperature Thermal Shock

The need for reliable bonded interface materials is critical to realize the performance benefits of wide-bandgap devices in power electronics modules, especially in operating temperatures greater than 150 degrees C. In this paper, we investigate the thermomechanical performance of sintered copper (Cu) as a large-area attachment, bonded between Cu baseplates and active-metal-bonded substrates, under accelerated thermal shock (-40 degrees C to 200 degrees C) conditions. In the fabrication phase of the samples, we used different stencil patterns and found that the grid and stripe patterns resulted in a better outgassing of the residual organics during the sintering process, thereby ensuring a substantially improved bond quality compared to a full-area print. The paste consisted of Cu microflakes, and we performed sintering using a Budatec SP300 sintering press at 275 degrees C with 15 MPa of bonding pressure for 5 minutes in a nitrogen atmosphere. Under accelerated experiments, we monitored the degradation of the sintered Cu bond in the samples through C-mode scanning acoustic microscope (C-SAM) images. To quantify the defect percentage in C-SAM images, we investigated image denoising techniques to exclude the pattern prints. Finally, we cross-sectioned a sample and obtained scanning electron microscope images, which revealed adhesive fracture as the dominant failure mechanism.

ADVANCED PROPULSION SYSTEMS,INORGANIC, ORGANIC, PH↗

Structure, Chemistry, and Charge Transfer Resistance of the Interface between Li 7 La 3 Zr 2 O 12 Electrolyte and LiCoO 2 Cathode

All-solid-state batteries promise significant safety and energy density advantages over liquid-electrolyte batteries. The interface between the cathode and the solid electrolyte is an important contributor to charge transfer resistance. Strong bonding of solid oxide electrolytes and cathodes requires sintering at elevated temperatures. Knowledge of the temperature dependence of the composition and charge transfer properties of this interface is important for determining the ideal sintering conditions. To understand the interfacial decomposition processes and their onset temperatures, model systems of LiCoO 2 (LCO) thin films deposited on cubic Al-doped Li 7 La 3 Zr 2 O 12 (LLZO) pellets were studied as a function of temperature using interface-sensitive techniques. X-ray photoelectron spectroscopy, secondary ion mass spectroscopy, and energy-dispersive X-ray spectroscopy data indicated significant cation interdiffusion and structural changes starting at temperatures as low as 300 °C. La 2 Zr 2 O 7 and Li 2 CO 3 were identified as decomposition products after annealing at 500 °C by synchrotron X-ray diffraction. X-ray absorption spectroscopy results indicate the presence of also LaCoO 3 in addition to La 2 Zr 2 O 7 and Li 2 CO 3 . On the basis of electrochemical impedance spectroscopy and depth profiling of the Li distribution upon potentiostatic hold experiments on symmetric LCO|LLZO|LCO cells, the interfaces exhibited significantly increased impedance, up to 8 times that of the as-deposited samples after annealing at 500 °C. Here, our results indicate that lower-temperature processing conditions, shorter annealing time scales, and CO 2 -free environments are desirable for obtaining ceramic cathode|electrolyte interfaces that enable fast Li transfer and high capacity.

25 ENERGY STORAGE↗

Development of low-cost technology for the next generation of high efficiency solar cells composed of earth abundant elements

The development of renewable, affordable, and environmentally conscious means of generating energy on a global scale represents a grand challenge of our time. Due to the “permanence” of radiation from the sun, solar energy promises to remain a viable and sustainable power source far into the future. Established single-junction photovoltaic technologies achieve high power conversion efficiencies (pce) near 20% but require complicated manufacturing processes that prohibit the marriage of large-scale throughput (e.g. on the GW scale), profitability, and quality control. Our approach to this problem begins with the synthesis of nanocrystals of semiconductor materials comprising earth abundant elements and characterized by material and optoelectronic properties ideal for photovoltaic applications, namely Cu2ZnSn(S,Se)4 (CZTSSe). Once synthesized, such nanocrystals are formulated into an ink, coated onto substrates, and processed into completed solar cells in such a way that enables scale-up to high throughput, roll-to-roll manufacturing processes. This project aimed to address the major limitation to CZTSSe solar cell pce’s – the low open-circuit voltage (Voc) reported throughout literature for devices comprised of this material. Throughout the project significant advancements have been made in fundamental understanding of the CZTSSe material and device limitations associated with this material system. Additionally, notable improvements have been made to our nanocrystal based processing technique to alleviate performance limitations due to the identified device limitations. Notably, (1) significant improvements have been made in reducing intra- and inter-nanoparticle heterogeneity, (2) improvements in device performance have been realized with novel cation substitution in Ge-alloyed CZTGeSSe absorbers, (3) systematic analysis of absorber sintering has been conducted to optimize the selenization process for large grain CZTSSe absorbers, (4) novel electrical characterization analysis techniques have been developed to identify significant limitations to traditional electrical characterization of CZTSSe devices, and (5) the developed electrical analysis techniques have been used to identify the role that band gap and electrostatic potential fluctuations have in limiting device performance for this material system. The device modeling and characterization of CZTSSe undertaken with this project have significant implications for the CZTSSe research community, as the identified limitations due to potential fluctuations are expected to be a performance limitation to high-efficiency CZTSSe devices fabricated from all current processing techniques. Additionally, improvements realized through enhanced absorber processing conditions to minimize nanoparticle and large-grain absorber heterogeneity are suggested to be beneficial processing improvements which should be applied to CZTSSe devices fabricated from all processing techniques. Ultimately, our research has indicated that improved performance for CZTSSe will be achieved through novel absorber processing which minimizes defect formation, elemental losses, secondary phase formation, and compositional uniformity in CZTSSe absorbers; we believe this novel absorber processing can be achieved through nanocrystal based processing of CZTSSe which is an active area of research at the conclusion of this award. While significant fundamental understanding of CZTSSe and the performance limitations associated with this material system, as well as notable improvements in the processing of nanocrystal based CZTSSe absorbers, have been achieved under this project, the limitation of two years of research funding towards our goals prevents further significant advancements directly identified through pce. improvements relative to those reported herein. As the characterization and modeling subtask of this project has been the main driving force for understanding device limitations, the conclusions of this analysis have just recently been applied to the processing of nanocrystal based CZTSSe absorbers -- with notable success. We expect the notable fundamental understanding of device limitations and absorber sintering achieved under this project will lead to significant improvements in device performance for CZTSSe devices in the near future for devices fabricated from a variety of processing techniques

14 SOLAR ENERGY↗