Results for “SKID LANDING” — Page 3

NASA NTRS1959

Tire-to-Surface Friction-Coefficient Measurements with a C-123B Airplane on Various Runway Surfaces

An investigation was conducted to obtain information on the tire-to-surface friction coefficients available in aircraft braking during the landing run. The tests were made with a C-123B airplane on both wet and dry concrete and bituminous pavements and on snow-covered and ice surfaces at speeds from 12 to 115 knots. Measurements were made of the maximum (incipient skidding) friction coefficient, the full-skidding (locked wheel) friction coefficient, and the wheel slip ratio during braking.

Sawyer, Richard H.↗

NASA NTRS1979

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces. A slip-velocity-controlled, pressure-bias-modulated system

The braking and cornering response of a slip velocity controlled, pressure bias modulated aircraft antiskid braking system is investigated. The investigation, conducted on dry and wet runway surfaces, utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC 9 series 10 airplane. The landing gear strut was replaced by a dynamometer. The parameters, which were varied, included the carriage speed, tire loading, yaw angle, tire tread condition, brake system operating pressure, and runway wetness conditions. The effects of each of these parameters on the behavior of the skid control system is presented. Comparisons between data obtained with the skid control system and data obtained from single cycle braking tests without antiskid protection are examined.

Stubbs, S. M.↗

NASA NTRS2024

Development of a Surface Water Transportation System for ISRU Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. Initial analysis assumptions allow for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Mars surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer water across the Martian surface from a source point to an in-situ resource utilization (ISRU) plant that would use this water as a feedstock to generate oxygen and methane to enable launch of the MAV. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Fluid Structure Interface↗

NASA NTRSDate not supplied

Assessment of a Surface Water Transportation System for ISRU Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. Initial analysis assumptions allow for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Mars surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer water across the Martian surface from a source point to an in-situ resource utilization (ISRU) plant that would use this water as a feedstock to generate oxygen and methane to enable launch of the MAV. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Fluid Structure Interface↗

NASA NTRSDate not supplied

Assessment of a Surface Propellant Transportation System Concept for Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. One potential architecture option allows for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Martian surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without its ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer cryogenic propellant, consisting of oxygen and methane, across the Martian surface from a delivery lander to the MAV to enable its launch. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Propellant↗

NASA NTRSDate not supplied

Assessment of a Surface Propellant Transportation System Concept for Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. One potential architecture option allows for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Martian surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without its ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This presentation describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer cryogenic propellant, consisting of oxygen and methane, across the Martian surface from a delivery lander to the MAV to enable its launch. Design considerations, concept of operations, and rover energetics will be discussed in this presentation.

Surface↗

NASA NTRS1977

Approach and landing test program status

This paper discusses captive-active tests of the Shuttle Orbiter's landing capability. Tests include: free-flight, in which a flare maneuver was undertaken to evaluate the control stick steering mode; separation, in which the pilot pitches up and rolls at a 20 deg bank angle; up and away flight, to test vehicle handling and stability; 2nd rollout, to test the anti-skid system and braking. Attention is given to bare airframe handling qualities, stressing the role of the pilot in controlling the craft.

Haise, F. W., Jr.↗

NASA NTRS2000

Design and Operating Characteristics of High-Speed, Small-Bore Cylindrical-Roller Bearings

The computer program SHABERTH was used to analyze 35-mm-bore cylindrical roller bearings designed and manufactured for high-speed turbomachinery applications. Parametric tests of the bearings were conducted on a high-speed, high-temperature bearing tester and the results were compared with the computer predictions. Bearings with a channeled inner ring were lubricated through the inner ring, while bearings with a channeled outer ring were lubricated with oil jets. Tests were run with and without outer-ring cooling. The predicted bearing life decreased with increasing speed because of increased contact stresses caused by centrifugal load. Lower temperatures, less roller skidding, and lower power losses were obtained with channeled inner rings. Power losses calculated by the SHABERTH computer program correlated reasonably well with the test results. The Parker formula for XCAV (used in SHABERTH as a measure of oil volume in the bearing cavity) needed to be adjusted to reflect the prevailing operating conditions. The XCAV formula will need to be further refined to reflect roller bearing lubrication, ring design, cage design, and location of the cage-controlling land.

Pinel, Stanley, I.↗

DOE OSTI2022

Blue Rock CropSpanPV - Low Cost Racking for Agricultural Solar Photovoltaics

In this work, a total of four solar panel layouts, applied to Agrivoltaics, are investigated. This study presents two hypotheses: 1. Prefabrication - Lower total cost can be achieved by constructing a pre-assembled, pre-wired solar array in a factory, with automation, then rapidly deploying it in the field. 2. Tension Structures - Using tension structures in a way to suspend an overhead solar array also reduces costs when compared to conventional support methods. Designs are presented for frames to hold the panels. Configurations are advanced to connect the frames into arrays. Supports and foundations to hold the arrays in the desired layout are calculated, selected and presented. Cost models are prepared for the four layouts, which include definition of the business enterprise, the manufacturing operation, and the required facility for production at scale. Cost models include, detail material and task/labor take-offs for both manufacturing and installation. Comparisons with conventional system adapted to Agrivoltaics reveal that the two hypotheses do not hold true. A prefabricated array requires additional material that is not needed in the base system and the cost of this additional material is not outweighed by the cost savings of reduced field installation. The cost of wire rope for a tension structure does result in an economy of material, however, the cost of end connections and tensioning devices adds significantly to the cost of the overall tension structure. Foundation loads with tension structures, especially the large wind uplift seen with a fixed tilt solar array, impose significant constraints and high costs. The following conclusions are recommended for further consideration: 1. Best Case Agrivoltaic Configuration - The best value/lowest cost configuration for agrivoltaics is the installation of solar panels mounted on a single axis tracker in either a 2-in-portrait or 2-in landscape arrangement. This is useful for grazing lands and for staple crops which require high light levels. These applications represent the vast majority of the potential agrivoltaic market. Important elements in this configuration are the specific geometric layout coordinated with the various field operations and a control system linked between the farm equipment and single axis tracker. The control system is to monitor location and orientation, then actively tilt the solar panels or brake the field equipment to provide clearance and avoid collisions. 2. Long Span Applications - The use of tension structures for an overhead fixed tilt array is beneficial where long spans are a necessity, especially where the base support in the project location has consolidated rock near the surface or some other solid structure. One application is spanning wide irrigation canals. Another may be as an installation at the top deck of parking structures. 3. Direct Ground Mount Configuration – Having skids at the base of a pre-fabricated array that extend when the array is deployed, could be a successful design. This could be a useful strategy for dense, flat, ground-mount configurations like that employed by a couple of successful commercial operations (5G Maverick and Erthos). Arrays would be orientated north and south, deployed very low on prepared grade. Arrays would be aligned closely next to each other and anchored with small ground screws or simply with ballast. This same product arrangement could be very useful for rapid deployment and set-up of solar arrays for temporary deployments, disaster response and the military operations

14 SOLAR ENERGY↗

NASA NTRS2011

Full-Scale Crash Test of an MD-500 Helicopter

A full-scale crash test was successfully conducted in March 2010 of an MD-500 helicopter at NASA Langley Research Center s Landing and Impact Research Facility. The reasons for conducting this test were threefold: 1 To generate data to be used with finite element computer modeling efforts, 2 To study the crashworthiness features typically associated with a small representative helicopter, and 3 To compare aircraft response to data collected from a previously conducted MD-500 crash test, which included an externally deployable energy absorbing (DEA) concept. Instrumentation on the airframe included accelerometers on various structural components of the airframe; and strain gages on keel beams, skid gear and portions of the skin. Three Anthropomorphic Test Devices and a specialized Human Surrogate Torso Model were also onboard to collect occupant loads for evaluation with common injury risk criteria. This paper presents background and results from this crash test conducted without the DEA concept. These results showed accelerations of approximately 30 to 50 g on the airframe at various locations, little energy attenuation through the airframe, and moderate to high probability of occupant injury for a variety of injury criteria.

Littell, Justin↗

NASA NTRS1981

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces: Hydromechanically controlled system

The investigation utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC-9 series 10 airplane. The landing-gear strut was replaced by a dynamometer. During maximum braking, average braking behavior indexes based upon brake pressure, brake torque, and drag-force friction coefficient developed by the antiskid system were generally higher on dry surfaces than on wet surfaces. The three braking behavior indexes gave similar results but should not be used interchangeably as a measure of the braking of this antiskid sytem. During the transition from a dry to a flooded surface under heavy braking, the wheel entered into a deep skid but the antiskid system reacted quickly by reducing brake pressure and performed normally during the remainder of the run on the flooded surface. The brake-pressure recovery following transition from a flooded to a dry surface was shown to be a function of the antiskid modulating orifice.

Tanner, J. A.↗

NASA NTRS2010

Crash Test of an MD-500 Helicopter with a Deployable Energy Absorber Concept

On December 2, 2009, a full scale crash test was successfully conducted of a MD-500 helicopter at the NASA Langley Research Center Landing and Impact Research Facility . The purpose of this test was to evaluate a novel composite honeycomb deployable energy absorbing (DEA) concept for attenuation of structural and crew loads during helicopter crashes under realistic crash conditions. The DEA concept is an alternative to external airbags, and absorbs impact energy through crushing. In the test, the helicopter impacted the concrete surface with 11.83 m/s (38.8 ft/s) horizontal, 7.80 m/s (25.6 ft/s) vertical and 0.15 m/s (0.5 ft/s) lateral velocities; corresponding to a resultant velocity of 14.2 m/s (46.5 ft/s). The airframe and skid gear were instrumented with accelerometers and strain gages to determine structural integrity and load attenuation, while the skin of the airframe was covered with targets for use by photogrammetry to record gross vehicle motion before, during, and after the impact. Along with the collection of airframe data, one Hybrid III 50th percentile anthropomorphic test device (ATD), two Hybrid II 50th percentile ATDs and a specialized human surrogate torso model (HSTM) occupant were seated in the airframe and instrumented for the collection of occupant loads. Resultant occupant data showed that by using the DEA, the loads on the Hybrid II and Hybrid III ATDs were in the Low Risk regime for the injury criteria, while structural data showed the airframe retained its structural integrity post crash. Preliminary results show that the DEA is a viable concept for the attenuation of impact loads.

Littell, Justin D.↗

NASA NTRS2019

Towards Articulated Mobility and Efficient Docking for the DuAxel Tethered Robot System

Sites of increasing interest for planetary science,such as craters, cold traps, and vents lie in terrains that are inaccessible to state-of-the-art rovers. The Jet Propulsion Laboratory, in collaboration with Caltech, is actively developing a tethered mobile robot, Axel, for traversing and exploring extremely steep terrain, such as Recurring Slope Lineae on Mars and vertical pits on the Moon. However, on Mars, where landing-site uncertainty is high due to the presence of an atmosphere, Axel may need to traverse several kilometers from its lander untethered due to a ﬁnite tether carrying capacity (⇠300m). This paper proposes a novel design for a hybrid mobility system that allows a pair of Axel rovers to dock, lock, and drive long distances as a four-wheeled, articulated steering vehicle. The design improves upon prior efforts to achieve DuAxel mobility by leveraging two actuated docking mechanisms attached on opposite ends of a central module to enable ‘sit/stand’ functionality; the prior DuAxel system was limited to skid steering, which was inefﬁcient due to Axel’s grouser-style, high-friction wheels. In the proposed system, the ‘sit’ conﬁguration is achieved by aligning each dock parallel to the surface, allowing one Axel to detach and explore while the other remains docked and serves as a backup. While ‘sitting’, the central module rests on the ground and is outﬁtted with shovel-style wedges for passive anchoring to sandy terrain (an optional drill can be integrated for anchoring to rock). In order to ‘stand’, the exploring Axel reattaches, locks, and both docks are rotated until Axel’s tether caster arm is upright and the central module is lifted off the ground. Once upright, each Axel rotates about a pivot point for articulated, all-wheel steering, which is accomplished by applying differential wheel torques. The main contributions of this paper are i) a detailed systems design of the docking mechanism and central module, ii) kinematic modeling of articulated mobility and ‘sit/stand’ docking functionality, and iii) initial testing in a relevant environment to characterize the mobility of the proposed system.

Nesnas, Issa↗

NASA NTRS1973

Cornering characteristics of a 40 by 14-16 type 7 aircraft tire and a comparison with characteristics of a C40 by 14-21 cantilever aircraft tire

An investigation was conducted at the Langley aircraft landing loads and traction facility to determine the cornering characteristics of a 40 x 14-16 type VII aircraft tire. These characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained for the tire operating on dry, damp and flooded runway surfaces over a range of yaw angles from 0 deg to 20 deg and at ground speeds from 5 to 100 knots, both with and without braking. The results of this investigation indicated that the cornering capability of the 40 x 14-16 type VII aircraft tire is degraded by high ground speeds, thin-film lubrication and tire hydroplaning effects on the wet surfaces, and brake torque. The cornering capability is greatly diminished when locked-wheel skids are encountered.

Tanner, J. A.↗

NASA NTRS2014

Terrain Physical Properties Derived from Orbital Data and the First 360 Sols of Mars Science Laboratory Curiosity Rover Observations in Gale Crater

Physical properties of terrains encountered by the Curiosity rover during the rst 360 sols of operations have been inferred from analysis of the scour zones produced by Sky Crane Landing System engine plumes, wheel touch down dynamics, pits produced by Chemical Camera (ChemCam) laser shots, rover wheel traverses over rocks, the extent of sinkage into soils, and the magnitude and sign of rover-based slippage during drives. Results have been integrated with morphologic, mineralogic, and thermophysical properties derived from orbital data, and Curiosity-based measurements, to understand the nature and origin of physical properties of traversed terrains. The hummocky plains (HP) landing site and traverse locations consist ofmoderately to well-consolidated bedrock of alluvial origin variably covered by slightly cohesive, hard-packedbasaltic sand and dust, with both embedded and surface-strewn rock clasts. Rock clasts have been addedthrough local bedrock weathering and impact ejecta emplacement and form a pavement-like surface in whichonly small clasts (5 to 10 cm wide) have been pressed into the soil during wheel passages. The beddedfractured (BF) unit, site of Curiositys rst drilling activity, exposes several alluvial-lacustrine bedrock unitswith little to no soil cover and varying degrees of lithication. Small wheel sinkage values (1 cm) for both HPand BF surfaces demonstrate that compaction resistance countering driven-wheel thrust has been minimaland that rover slippage while traversing across horizontal surfaces or going uphill, and skid going downhill,have been dominated by terrain tilts and wheel-surface material shear modulus values.

Mars Science Laboratory Curiosity Gale Crater↗

NASA NTRS1997

Sensitivity of Runway Occupancy Time (ROT) to Various Rollout and Turnoff (ROTO) Factors: Complete Set of Plotted Data - Volume 2

The Terminal Area Productivity (TAP) research program was initiated by NASA to increase the airport capacity for transport aircraft operations. One element of the research program is called Low Visibility Landing and Surface Operations (LVLASO). A goal of the LVLASO research is to develop transport aircraft technologies which reduce Runway Occupancy Time (ROT) so that it does not become the limiting factor in the terminal area operations that determine the capacity of a runway. Under LVLASO, the objective of this study was to determine the sensitivity of ROT to various factors associated with the Rollout and Turnoff (ROTO) operation for transport aircraft. The following operational factors were studied and are listed in the order of decreasing ROT sensitivity: ice/flood runway surface condition, exit entrance ground speed, number of exits, high-speed exit locations and spacing, aircraft type, touchdown ground speed standard deviation, reverse thrust and braking method, accurate exit prediction capability, maximum reverse thrust availability, spiral-arc vs. circle-arc exit geometry, dry/slush/wet/snow runway surface condition, maximum allowed deceleration, auto asymmetric braking on exit, do not stow reverse thrust before the exit, touchdown longitudinal location standard deviation, flap setting, anti-skid efficiency, crosswind conditions, stopping on the exit and touchdown lateral offset.

Goldthorpe, S. H.↗

NASA NTRS1997

Sensitivity of Runway Occupancy Time (ROT) to Various Rollout and Turnoff (ROTO) Factors

The Terminal Area Productivity (TAP) research program was initiated by NASA to increase the airport capacity for transport aircraft operations. One element of the research program is called Low Visibility Landing and Surface Operations (LVLASO). A goal of the LVLASO research is to develop transport aircraft technologies which reduce Runway Occupancy Time (ROT) so that it does not become the limiting factor in the terminal area operations that determine the capacity of a runway. Under LVLASO, the objective of this study was to determine the sensitivity of ROT to various factors associated with the Rollout and Turnoff (ROTO) operation for transport aircraft. The following operational factors were studied and are listed in the order of decreasing ROT sensitivity: ice/flood runway surface condition, exit entrance ground speed, number of exits, high-speed exit locations and spacing, aircraft type, touchdown ground speed standard deviation, reverse thrust and braking method, accurate exit prediction capability, maximum reverse thrust availability, spiral-arc vs. circle-arc exit geometry, dry/slush/wet/snow runway surface condition, maximum allowed deceleration, auto asymmetric braking on exit, do not stow reverse thrust before the exit, touchdown longitudinal location standard deviation, flap setting, anti-skid efficiency, crosswind conditions, stopping on the exit and touchdown lateral offset.

Goldthorpe, S. H.↗