Search NASA⌕ Search

SEARCH · Search NASA

Results for “SLENDER CONE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

A comparison of experimental and computational results for 5 and 10 degree cones at high Mach numbers

Experiments were performed on 5 and 10 deg slender cones at a velocity of approximately 5 km/sec in the NASA-Ames ballistic ranges. The flowfields for the cones were computed using ideal-gas and chemical nonequilibrium-air parabolized Navier-Stokes codes. Experimentally determined drag coefficients and shock shapes are compared with the results of the computer codes. Both the flight-data analysis methods and the computational codes are examined to achieve the most meaningful comparison. Under the conditions of the experiments, skin-friction drag makes up approximately 50 percent of the total drag for the 5 deg cone and 30 percent of the total drag for the 10 deg cone. Computed drag coefficients of the 10 deg cone agree well with the experimental values; predictions fall below the experimental values for the 5 deg cone.

Strawa, A. W.↗
NASA NTRS1973

Laminar film condensation on the inside of slender, rotating truncated cones.

A solution for film condensation on the inside of slender rotating truncated cones is established in the region where the half cone angle phi is close to zero and where the equation of Dhir and Lienhard (1971) is no longer valid. All the familiar assumptions used in Nusselt's theory of laminar film condensation are assumed valid, including negligible sub-cooling and momentum changes in the condensate film, no interfacial shear between the condensate and the vapor, and pure conduction within the condensate film. A Runge-Kutta numerical integration method using a digital computer was used. Results for a specific geometry are given for water condensing at 212 F on a condenser wall maintained at 70 F.

Marto, P. J.↗
NASA NTRS1993

Transition on a sharp cone at high enthalpy - New measurements in the shock tunnel T5 at GALCIT

An exploratory study of the laminar, transitional and turbulent boundary layer on a slender cone in hypervelocity flow was conducted in the high-enthalpy shock tunnel T5. A novel flow visualization technique using sodium seeding to increase the sensitivity of conventional interferometric techniques by resonant enhancement of the refractivity of the medium was developed to study its structure. The experiments were designed to cover a large range of specific reservoir enthalpy, ranging from the perfect-gas region to the range where significant oxygen and some nitrogen dissociation and recombination effects may be expected in the boundary layer. Surface heat flux measurements indicate that the transition Reynolds number is approximately the same as that observed in cold hypersonic flow in conventional continuous flow facilities, but significantly lower than that observed in 'quiet' tunnels. No significant effect of reservoir specific enthalpy on transition was observed. The heat flux distribution showed differences between the air and the nitrogen experiments in the laminar regime. These are consistent with the presence of recombination of oxygen at the wall. This view is supported by the fact that this effect is absent in the low-enthalpy region, where the heat flux distribution agrees with the similarity theory.

Germain, P.↗
NASA NTRS1972

A survey of NASA Langley studies on high-speed transition and the quiet tunnel

A quantitative experimental and theoretical assessment of the role of wind-tunnel disturbances in the boundary-layer transition process at hypersonic speeds is presented. The various approaches and recent results for the development of a low-noise-level tunnel are presented. A statistical parametric study of transition data with a large computer is shown for cones in free flight, ballistic ranges, and wind tunnels at essentially zero angle of attack. New transition results for slender cones at small angle of attack are also given, as are studies of transition at high angle of attack, which are compared with various correlation attempts. Included are results which indicate that hypersonic transition in the outer part of the boundary layer precedes the manifestation of transition at the wall.

Beckwith, I. E.↗
NASA NTRS1987

Experimental investigation of hypersonic aerodynamics

An extensive series of ballistic range tests are currently being conducted at the Ames Research Center. These tests are intended to investigate the hypersonic aerodynamic characteristics of two basic configurations, which are: the blunt-cone Galileo probe which is scheduled to be launched in late 1989 and will enter the atmosphere of Jupiter in 1994, and a generic slender cone configuration to provide experimental aerodynamic data including good flow-field definition which computational aerodynamicists could use to validate their computer codes. Some of the results obtained thus far are presented and work for the near future is discussed.

Heinemann, K.↗
NASA NTRS1983

Free-stream noise and transition measurements on a cone in a Mach 3.5 pilot low-disturbance tunnel

A small scale Mach 3.5 wind tunnel incorporating certain novel design features and intended for boundary-layer-transition research has been tested. The free stream noise intensities and spectral distributions were determined throughout the test section for several values of unit Reynolds number and for nozzle boundary layer bleed on and off. The boundary layer transition location on a slender cone and the response of this to changes in the noise environment were determined. Root mean square free stream noise levels ranged from less than one tenth up to values approaching those for conventional nozzles, with the lowest values prevailing at upstream locations within the nozzle. For low noise conditions, cone transition Reynolds numbers were in the range of those for free flight; whereas for high noise conditions, they were in the range of those in conventional tunnels.

Beckwith, I. E.↗
NASA NTRS1961

Aerodynamic Force Characteristics of a Series of Lifting Cone and Cone-Cylinder Configurations at a Mach Number of 6.83 and Angles of Attack up to 130 Deg

Force tests of a series of right circular cones having semivertex angles ranging from 5 deg to 45 deg and a series of right circular cone-cylinder configurations having semivertex angles ranging from 5 deg to 20 deg and an afterbody fineness ratio of 6 have been made in the Langley 11-inch hypersonic tunnel at a Mach number of 6.83, a Reynolds number of 0.24 x 10.6 per inch, and angles of attack up to 130 deg. An analysis of the results made use of the Newtonian and modified Newtonian theories and the exact theory. A comparison of the experimental data of both cone and cone-cylinder configurations with theoretical calculations shows that the Newtonian concept gives excellent predictions of trends of the force characteristics and the locations with respect to angle of attack of the points of maximum lift, maximum drag, and maximum lift-drag ratio. Both the Newtonian a.nd exact theories give excellent predictions of the sign and value of the initial lift-curve slope. The maximum lift coefficient for conical bodies is nearly constant at a value of 0.5 based on planform area for semivertex angles up to 30 deg. The maximum lift-drag ratio for conical bodies can be expected to be not greater than about 3.5, and this value might be expected only for slender cones having semivertex angles of less than 5 deg. The increments of angle of attack and lift coefficient between the maximum lift-drag ratio and the maximum lift coefficient for conical bodies decrease rapidly with increasing semivertex angles as predicted by the modified Newtonian theory.

Penland, Jim A.↗
NASA NTRS1966

Thin-film gage measures low heat-transfer rates

Low heat-transfer gage facilitates determination of the transition between laminar and turbulent conditions, in the boundary layer surrounding slender and moderately slender cones under test in a hypersonic blowdown helium tunnel. The gage consists of a thin layer of vacuum-evaporated platinum on a heat resistant glass substrate contoured to fit model surfaces.

Spitzer, C. R.↗
NASA NTRS1973

Comparison of the aerodynamic characteristics of an ablating and nonablating blunted conical body

The influence of ablation on the aerodynamic characteristics of a blunted slender cone was investigated. Plastic models were launched in free flight at ablating conditions. The results were compared with results of similar tests using metal nonablating models. Ablation was found to decrease the dynamic stability and the drag, but had little effect on static stability and lift. The plastic models appeared to experience ablation-induced roll.

Kruse, R. L.↗
NASA NTRS1986

Effects of compressibility and free-stream turbulence on boundary layer transition in high-subsonic and transonic flows

Based on the existing boundary layer transition data, the effects of compressibility, pressure fluctuations, and free-stream turbulence have been reexamined for subsonic and transonic flow speeds. It is confirmed that the compressibility effects may be adequately expressed in terms of a simple correlation with free-stream Mach number. Pressure fluctuations, especially at low levels, do not seem to significantly affect the transition phenomenon. Effects of free-stream turbulence in high-subsonic and transonic flows are similar to the trends observed for low-speed flows and the transition process is hastened. The trends, as seen from slender cone flow data, seem to suggest power law correlations between transition Reynolds number and free-stream turbulence.

Murthy, S. V.↗
NASA NTRS1988

An imaging system for quantitive surface temperature mapping using two-color thermographic phosphors

A technique for obtaining detailed quantitative temperature distributions on test models in hypersonic wind tunnels is presented. This technique is based on the ratio of blue to green (450, 520 nm) emission from an UV (365 nm) excited phosphor coating. Separately filtered images are recorded from a three-tube color camera, utilizing off-the-shelf front-end video optics to discriminate wavelengths. Two demonstration studies in a 31-inch Mach 10 tunnel are discussed. One study presents the windward surface temperature-time history for a transatmospheric vehicle, and the other illustrates nosetip heating on a spherically blunted slender cone.

Buck, Gregory M.↗
NASA NTRS1990

An embedded grid formulation applied to a delta wing

Applications using a three-dimensional embedded grid scheme are made to high angle of attack viscous flow over two bodies: a slender cone using the conical approximation and a 75 deg swept delta wing. The embedded grids are used principally to improve the numerical resolution of the separated vortical flow above the body. Detailed comparisons are made with experimental measurements of the velocity field over the delta wing. The prediction of the maximum steamwise velocity is improved using two levels of embedded grid refinement but is still less than the experimental measurements available from a laser velocimeter.

Krist, Sherrie L.↗
NASA NTRS1990

Application of the LAURA code for slender-vehicle aerothermodynamics

Application of a three-dimensional thin-layer Navier-Stokes code (LAURA) to compute the laminar, perfect gas aerothermodynamics of slender vehicles is demonstrated. Comparison of solutions with experimental data enabled an assessment of the code's aerodynamic heating prediction capabilities. The results show radial grid refinement to a wall cell Reynolds number of 2 to be accurate for predicting aerodynamic heating to a slender cone. Additional comparisons for an 80 deg slab-delta wing and a generic Aero-Space Plane vehicle show the method to be generally accurate using this radial cell spacing. Discrepancies between the predicted and measured heating in a region of crossflow separation on the Aero-Space Plane geometry are noted which indicates the need for further study. While additional applications and comparisons are required to fully test the LAURA program, the results of this study demonstrate the current level of confidence and the engineering utility of this particular code.

Thompson, Richard A.↗
NASA NTRS1991

An approximate Riemann solver for hypervelocity flows

We describe an approximate Riemann solver for the computation of hypervelocity flows in which there are strong shocks and viscous interactions. The scheme has three stages, the first of which computes the intermediate states assuming isentropic waves. A second stage, based on the strong shock relations, may then be invoked if the pressure jump across either wave is large. The third stage interpolates the interface state from the two initial states and the intermediate states. The solver is used as part of a finite-volume code and is demonstrated on two test cases. The first is a high Mach number flow over a sphere while the second is a flow over a slender cone with an adiabatic boundary layer. In both cases the solver performs well.

Jacobs, Peter A.↗
NASA NTRS1992

A method of analyzing holographic interferograms of ballistic models in hypersonic free-flight

The objective of this research was to develop a method to extract integrated flowfield density information from finite-fringe interferograms produced with a laser holographic interferometer. This method was applied to two sets of holograms. An aeroassist flight experiment model flown in a mixture of 50 percent air - 50 percent argon and a blunt slender cone flown in air were flown at Mach 14.5 into freestream static pressures of 0.04 and 0.08 atm, respectively. The method of analysis can be separated into two main divisions. The first step is to identify fringes inside the wake in terms of the fringes in the freestream. This is important because refraction effects have obscured the region near the shock such that fringes cannot be followed into the wake region. The second step is to extrapolate the freestream fringes into the wake to determine the location of disturbance-related fringe shifts. Coupled with assumptions about the shape of the wake region, the locations of the disturbance-related fringe shifts can be related to the integrated density.

Kieffer, Douglas L.↗
NASA NTRS1992

Modeling variable blowing effects in the turbulent hypersonic boundary layer

Studies of the effects of variable blowing in turbulent hypersonic boundary layers are presented. Numerical calculations of the skin friction and surface heat transfer rates are compared to the experimental measurements of Holden (1990) for a slender cone at zero angle of attack in steady flows at Mach numbers of 11 and 13. An analysis of the transpiration feed system of the cone model was performed and showed that the blowing rate could be variable along the cone surface. This effect is confirmed by internal pressure measurements which were taken inside the cone model. The blowing rates are recalibrated using the internal gauge readings and used as the wall boundary condition for a compressible turbulent boundary layer calculation using the low Reynolds number k-epsilon model of Chien (1982). At low blowing rates, the boundary layer calculations indicate that a situation where both the effects of suction and blowing are present within the same flow. The results show excellent qualitative prediction of the experimental data.

Vanosdol, John G.↗
NASA NTRS1992

Approximate Riemann solver for hypervelocity flows

We describe an approximate Riemann solver for the computation of hypervelocity flows in which there are strong shocks and viscous interactions. The scheme has three stages, the first of which computes the intermediate states assuming isentropic waves. A second stage, based on the strong shock relations, may then be invoked if the pressure jump across either wave is large. The third stage interpolates the interface state from the two initial states and the intermediate states. The solver is used as part of a finite-volume code and is demonstrated on two test cases. The first is a high Mach number flow over a sphere while the second is a flow over a flow over a slender cone with an adiabatic boundary layer. In both cases the solver performs well.

Jacobs, P. A.↗