SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Guidelines are presented for use of the computer program STIPPAN to simulate the subsonic flow in a slotted wind tunnel test section with a known model disturbance. Input data requirements are defined in detail and other aspects of the program usage are discussed in more general terms. The program is written for use in a CDC CYBER 200 class vector processing system.
A numerical model of a slotted wind tunnel test section, intended for use with sparsely measured wall pressures in a wall interference assessment procedure, is described. The numerical model includes a discrete finite length wall slot representation and accounts for the nonlinear effects of the dynamic pressure of the slot outflow jet and of the low energy of slot inflow air. By using th numerical model in a wall interference prediction mode, it is demonstrated that accounting for slot discreteness is important in interpreting wall pressures measured between slots, and that accounting for finite slot length and nonlinear effects in the slot boundary condition can yield significant departures from the wall interference predicted using the classical linear homogeneous infinite-length wall representation.
A simplified physical model was constructed which simulates the viscous crossflow in a fluid layer near the slots at a fixed streamwise location in a slotted wind tunnel. For low to moderate Reynolds numbers, numerical solutions of the two dimensional, incompressible Navier-Stokes equations in stream function and vorticity, which govern the model flow, were obtained. Fairly general slot geometry was incorporated by means of the Thompson-Thames-Mastin transformation. An approximate factorization scheme with cyclic acceleration parameters was employed to solve a finite difference analog of the stream function equation. The vorticity equation was numerically solved with a modified version of the classical alternating direction implicit scheme. Although no quantitative assessment of solution accuracy can be made, numerical results for variations in incremental wall pressure around the slat are at least qualitatively similar to some experimental results.
A simplified physical model is constructed which simulates the viscous crossflow in a fluid layer near the slots at a fixed streamwise location in a slotted wind tunnel. For low to moderate Reynolds numbers, numerical solutions of the two-dimensional, incompressible Navier-Stokes equations in stream function and vorticity, which govern the model flow, are obtained. Fairly general slot geometry is incorporated by means of the Thompson-Thames-Mastin transformation. An approximate factorization scheme with cyclic acceleration parameters is employed to solve a finite difference analog of the stream function equation. The vorticity equation is numerically solved with a modified version of the classical alternating direction implicit (ADI) scheme. Although no quantitative assessment of solution accuracy can be made, numerical results for variations in incremental wall pressure around the slot are at least qualitatively similar to some experimental results of Berndt and Sorenson.
Exploratory calculations of transonic flows over the airfoil with a quarter-chord oscillating flap were made using a program which obtains approximate solutions to the Euler equations with an explicit, shock-capturing, finite-difference scheme. The calculations, essentially inviscid and for the airfoil at zero angle-of-attack in a free-stream, are at Mach numbers and reduced frequencies which were tested in experiments by Tijdeman. The oscillatory lifts from analogus calculations by various investigators generally agree with one another better than they agree with Tijdeman's data. Inclusion in the calculations of an approximate modelling of boundary conditions expected at slotted wind tunnel walls tends to shift some of the results closer to the experimental values.
A computational simulation of a transonic wind tunnel test section with longitudinally slotted walls is developed and described herein. The nonlinear slot model includes dynamic pressure effects and a plenum pressure constraint, and each slot is treated individually. The solution is performed using a finite-difference method that solves an extended transonic small disturbance equation. The walls serve as the outer boundary conditions in the relaxation technique, and an interaction procedure is used at the slotted walls. Measured boundary pressures are not required to establish the wall conditions but are currently used to assess the accuracy of the simulation. This method can also calculate a free-air solution as well as solutions that employ the classical homogeneous wall conditions. The simulation is used to examine two commercial transport aircraft models at a supercritical Mach number for zero-lift and cruise conditions. Good agreement between measured and calculated wall pressures is obtained for the model geometries and flow conditions examined herein. Some localized disagreement is noted, which is attributed to improper simulation of viscous effects in the slots.
A large wind tunnel, approximately 8 feet in diameter, has been converted to transonic operation by means of slots in the boundary extending in the direction of flow. The usefulness of such a slotted wind tunnel, already known with respect to the reduction of the subsonic blockage interference and the production of continuously variable supersonic flows, has been augmented by devising a slot shape with which a supersonic test region with excellent flow quality could be produced. Experimental locations of detached shock waves ahead of axially symmetric bodies at low supersonic speeds in the slotted test section agreed satisfactorily with predictions obtained by use of existing approximate methods.
Wind tunnel investigation of external-flow jet-flap transport configuration having full-span tripple-slotted flaps - graphs
The traditional procedure for estimating the performance of slotted walls for airfoil wind tunnels is reviewed, and a modification which improves the accuracy of this procedure is described. Unlike the traditional procedure, the modified procedure indicates that the design of airfoil wind-tunnel walls which induce minimal blockage and streamline-curvature effects is feasible. The design and testing of such a slotted wall is described. It is shown experimentally that the presence of a model can affect the plenum pressure and thus make the use of the plenum pressure as a calibration reference questionable. Finally, an ONERA experiment which shows the effect of the sidewall boundary layer on the measured model normal force is discussed.
An investigation was conducted in a 300-mph 7- by 10- foot tunnel to obtain data for a slot spoiler direct lift control system. Slot spoilers are believed to have advantages over flap-type direct lift control (DLC) systems because of the small amount of power required for actuation. These tests, run at a Reynolds number of 1,400,000 showed that up to 78 percent of the lift due to flap deflection could be spoiled by opening several spanwise slots within the flaps. For a given lift change the drag change was significantly less than that which would be obtained by a variable flap DLC system. A nozzle-shaped slot was the most effective of the slot shapes tested.
Explore the source record for details and available documents.
Wind tunnel tests of swept wing jet transport aircraft model with four pod mounted engines under wing and external flow, jet augmented double slotted flap
The flow in the vicinity of a longitudinally slotted wind-tunnel wall is theoretically analyzed, and equations describing the pressure drop across the wall are derived. The ideal form of the slotted-wall boundary condition is shown to effectively model the wall pressure drop upstream of the point of maximum model thickness providing that a zero-shift correction to the reference pressure is included in the analysis. The wall-pressure drop equations can be linearized by subtracting the tunnel-empty boundary condition. Good correlation is obtained between experimental and theoretical values for variations in Mach number and angle of attack.
The design and wind tunnel test of a model vertical tail fin is described in this report. The model is designed to provide the aerodynamic forces necessary for lateral stabilization without moving parts or a separate source of power. It employs scoop-fed slots on both surfaces of the symmetrical airfoil. They are to be controlled differentially by means of a fluidic amplifier to implement an automatic fulltime lateral stabilization system. The results of tests show that the control of forces is stable and quite linear in various modes of operation. Significant forces were produced that can be increased as necessary by increasing slot size and scoop size. Slots can be located ahead of the conventional rudder and the scoop can be at the base of the vertical tail fin to avoid the need for major changes in conventional aircraft design. The first phase of the work demonstrated the feasibility of no-moving-parts aircraft control. The second phase established that a practical fluidic amplifier can be built to control slot flows from fluidic signals. Recommendations are made to optimize the design of the fluidic amplifier and to characterize its dynamic response in support of further analytical studies.
A wind-tunnel investigation has been conducted to determine the effects of slot spoilers on the longitudinal and lateral aerodynamic characteristics of a full-scale mockup of a light twin-engine airplane. The slots were located along the leading edge of the flaps and were used to modulate the flap-induced lift as a possible means of achieving direct lift control. The data showed that the slots were effective in spoiling up to 61 percent of the flap-induced lift, but that an adverse pitching-moment change (nose up) accompanied opening the slots. Opening the slots was found to decrease slightly the downwash angle at the tail and to increase slightly the longitudinal stability of the model.
A subsonic wind tunnel investigation of pneumatic vortex flow control on a chined forebody using slots was accomplished at a dynamic pressure of 50 psf resulting in a R(n)/ft of 1.3 x 10(exp 6). Data were acquired from angles of attack ranging from -4deg to +34deg at side slips of +0.4deg and +10.4deg. The test article used in this study was the 10% scale Fighter Lift and Control (FLAC) advanced diamond winged, vee-tailed fighter configuration. Three different slot blowing concepts were evaluated; outward, downward, and tangential with ail blowing accomplished asymmetrically. The results of three different mass flows (0.067, 0.13, and 0.26 lbm/s; C(sub mu)'s of less than or equal to 0.006, 0.011. and 0.022 respectively) were analyzed and reported. Test data are presented on the effects of mass flows, slot lengths and positions and blowing concepts on yawing moment and side force generation. Results from this study indicate that the outward and downward blowing slots developed yawing moment and side force increments in the direction opposite of the blowing side while the tangential blowing slots generated yawing moment and side force increments in the direction towards the blowing side. The outward and downward blowing slots typically produced positive pitching moment increments while the tangential blowing slots typically generated negative pitching moment increments. The slot blowing nearest the forebody apex was most effective at generating the largest increments and as the slot was moved aft or increased in length, its effectiveness at generating forces and moments diminished.
The wall interference assessment/correction code presented is nonlinear, involves four walls, and is applicable to transonic airfoil data from wind tunnels with shaped, solid top and bottom walls. Attention is given to its application to data from the NASA 0.3-m Transonic Cryogenic Tunnel Adaptive Test Section, for two sizes of a NACA 0012 airfoil and to simulated data for an inviscid two-dimensional full-potential code. This study indicates that while adaptive wall wind tunnels significantly reduce some aspects of wall-interference effects (by comparison to straight solid and slotted wall wind tunnels), residual wall and other interference effects are present.
The effect of slot width on transition and noise attenuation of a planar rod wall sound shield has been investigated at Mach 6. Boundary layer laminarization was obtained by induced suction through adjustable slots or gaps between the rods. Transition Reynolds numbers increased significantly with increasing gap width. The local mean flow field above the suction panel rod array was uniform. Important factors for design and performance of a supersonic wind-tunnel sound shield are rod diameter, gap-to-rod diameter ratio, surface finish of the rods, and leading-edge configuration.