Search NASA⌕ Search

SEARCH · Search NASA

Results for “SOARING FLIGHT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

An Analytical Thermal Model for Autonomous Soaring Research

A viewgraph presentation describing an analytical thermal model used to enable research on autonomous soaring for a small UAV aircraft is given. The topics include: 1) Purpose; 2) Approach; 3) SURFRAD Data; 4) Convective Layer Thickness; 5) Surface Heat Budget; 6) Surface Virtual Potential Temperature Flux; 7) Convective Scaling Velocity; 8) Other Calculations; 9) Yearly trends; 10) Scale Factors; 11) Scale Factor Test Matrix; 12) Statistical Model; 13) Updraft Strength Calculation; 14) Updraft Diameter; 15) Updraft Shape; 16) Smoothed Updraft Shape; 17) Updraft Spacing; 18) Environment Sink; 19) Updraft Lifespan; 20) Autonomous Soaring Research; 21) Planned Flight Test; and 22) Mixing Ratio.

Allen, Michael↗
NASA NTRS2007

Guidance and Control of an Autonomous Soaring UAV

Thermals caused by convection in the lower atmosphere are commonly used by birds and glider pilots to extend flight duration, increase cross-country speed, improve range, or simply to conserve energy. Uninhabited Aerial Vehicles (UAVs) can also increase performance and reduce energy consumption by exploiting atmospheric convection. An autonomous soaring research project was conducted at the NASA Dryden Flight Research Center to evaluate the concept through flight test of an electric-powered motor-glider with a wingspan of 4.27 m (14 ft). The UAV's commercial autopilot software was modified to include outer-loop soaring guidance and control. The aircraft total energy state was used to detect and soar within thermals. Estimated thermal size and position were used to calculate guidance commands for soaring flight. Results from a total of 23 thermal encounters show good performance of the guidance and control algorithms to autonomously detect and exploit thermals. The UAV had an average climb of 172 m (567 ft) during these encounters.

Allen, Michael J.↗
NASA NTRS1979

The application of microprocessor technology to in-flight computation

A modular design of a general purpose microprocessor-based computer to perform in-flight computations for cross-country soaring pilots is described. The basic requirements for the system are discussed. Several specialized applications of the computer are presented, including real-time pilot feedback and flight-test data acquisition and reduction.

Sawyer, P. L.↗
NASA NTRS1962

Dyna-Soar Bioastronautics

Dyna-Soar is a manned boost-orbit-glide vehicle. Conventional booster and guidance systems will place the glider on a course at the proper altitude and velocity with the resultant energy to accomplish the planned mission. After boost termination, the pilot verifies the course during orbit and controls the flight path during reentry, approach, and landing. The flight profiles and over-all flight regime for the Dyna-Soar's single-orbit mission will impose no new or extreme environmental hazards on the pilot. '!he environmental parameters of a normal space flight will not expose the pilot to stress magnitudes as great as pilots have experienced in the Mercury flights. Under presently planned flights, the pilot should be in an environment that is well within known human tolerances. We will present the calculated environmental stress to be imposed on the pilot in both normal and emergency conditions and the design techniques .developed to provide a cockpit that will keep the pilot well within his tolerance limits. The various primary environmental parameters will be discussed separately. The solution for each parameter will be discussed in a concurrent manner. No significance is attached to the order in which the specific parameters of the environment are considered.

Spacecraft↗
NASA NTRS1997

Toy Gliders

Toy designers at Hasbro, Inc. wanted to create a foam glider that a child could fly with little knowledge of aeronautics. But early in its development, the Areo Nerf gliders had one critical problem: they didn't fly so well. Through NASA's Northeast Regional Technology Transfer Center, Hasbro was linked with aeronautical experts at Langley Research Center. The engineers provided information about how wing design and shape are integral to a glider's performance. The Hasbro designers received from NASA not only technical guidance but a hands-on tutorial on the physics of designing and flying gliders. Several versions of the Nerf glider were realized from the collaboration. For instance, the Super Soaring Glider can make long-range, high performance flights while the Ultra-Stunt Glider is ideal for performing aerial acrobatics.

Source record↗
NASA NTRS2013

Bayesian Approach for Reliability Assessment of Sunshield Deployment on JWST

Deployable subsystems are essential to mission success of most spacecraft. These subsystems enable critical functions including power, communications and thermal control. The loss of any of these functions will generally result in loss of the mission. These subsystems and their components often consist of unique designs and applications, for which various standardized data sources are not applicable for estimating reliability and for assessing risks. In this study, a Bayesian approach for reliability estimation of spacecraft deployment was developed for this purpose. This approach was then applied to the James Webb Space Telescope (JWST) Sunshield subsystem, a unique design intended for thermal control of the observatory's telescope and science instruments. In order to collect the prior information on deployable systems, detailed studies of "heritage information", were conducted extending over 45 years of spacecraft launches. The NASA Goddard Space Flight Center (GSFC) Spacecraft Operational Anomaly and Reporting System (SOARS) data were then used to estimate the parameters of the conjugative beta prior distribution for anomaly and failure occurrence, as the most consistent set of available data and that could be matched to launch histories. This allows for an emperical Bayesian prediction for the risk of an anomaly occurrence of the complex Sunshield deployment, with credibility limits, using prior deployment data and test information.

Kaminskiy, Mark P.↗
NASA NTRS1972

Flexible wings for transportation.

The possible uses of flexible wings for transportation of passengers and cargo from point to point on earth are discussed along with emergency applications of flexible wings in connection with conventional aircraft. Topics considered include gliding and soaring as a sport, towing of flexible-wing gliders for cargo delivery, powered flight with small aircraft having folding flexible wings, aerial dropping of personnel and cargo on flexible wings instead of parachutes, landing and recovery of rocket payloads by means of flexible wings, and use of flexible wings with ejection seats and as an emergency landing system for conventional aircraft.

Rogallo, F. M.↗
NASA NTRS1931

Elmira soaring contest, 1930

This report details the Elmira, New York soaring contest of 1930 and provides up-current maps, experiences in piloting, distance flights, and a few details on glider design.

Hirth, Wolfram K E↗
NASA NTRS2006

Updraft Model for Development of Autonomous Soaring Uninhabited Air Vehicles

Large birds and glider pilots commonly use updrafts caused by convection in the lower atmosphere to extend flight duration, increase cross-country speed, improve range, or simply to conserve energy. Uninhabited air vehicles may also have the ability to exploit updrafts to improve performance. An updraft model was developed at NASA Dryden Flight Research Center (Edwards, California) to investigate the use of convective lift for uninhabited air vehicles in desert regions. Balloon and surface measurements obtained at the National Oceanic and Atmospheric Administration Surface Radiation station (Desert Rock, Nevada) enabled the model development. The data were used to create a statistical representation of the convective velocity scale, w*, and the convective mixing-layer thickness, zi. These parameters were then used to determine updraft size, vertical velocity profile, spacing, and maximum height. This paper gives a complete description of the updraft model and its derivation. Computer code for running the model is also given in conjunction with a check case for model verification.

Allen, Michael J.↗
NASA NTRS1975

Propulsive effects due to flight through turbulence

A simple and straightforward analysis is presented for evaluating the approximate magnitude of the propulsive effect for various types of airplane (soaring glider, light airplane, fighter, and transport). The airplane, subject to vertical gust disturbances, is assumed to be constrained to fly at constant airspeed and constant pitch angle. Changes in the magnitude and direction of the lift vector are taken into account. It is shown that the thrust effects due to turbulence vary as the square of the turbulence intensity and are quite small for moderate turbulence. Only for rather severe turbulence are the effects large enough to be given any consideration. The thrust coefficient is 10-20% of the drag coefficient of a soaring glider.

Phillips, W. H.↗
NASA NTRS1976

A simple total energy sensor

This research concerns a simple technique for total energy compensation having the primary requirement of good compensation with a low cost, easy to make sensor. A comprehensive library search and a small wind tunnel were used to explore fundamentals and to develop a number of probes which were flight tested with satisfactory results. Simple probe configurations were tested using the characteristics of laminar flow separation around a small cylinder to produce a sensor pressure having the desired relationship between static and dynamic pressures. Wind tunnel and flight tests confirmed the concepts for a wide range of speeds, altitudes, and flow directions encountered in soaring. Data and findings are presented, along with a discussion of factors important to total energy compensation.

Nicks, O. W.↗
NASA NTRS2001

A New and Innovative Use of the Thermal Knife and Kevlar Cord Components in a Restraint and Release System

A Kevlar cord and two thermal knives are key components in the Soar Array Restraint and Release System (SARRS) on the Microwave Anisotropy Probe (MAP) spacecraft at NASA's Goddard Space Flight Center. The SARRS uses a 25-foot (7.62 m) length Kevlar cord that encircles the spacecraft and secures the solar panels in stowed configuration for launch. Once in orbit, one of two redundantly configured thermal knives severs the Kevlar cord and permits the panels to deploy. The purpose of this paper is to present the details of the design, development test results, and the various innovations that were created during the development of this novel use of the thermal knife and Kevlar cord.

Stewart, Alphonso↗
NASA NTRS1973

Motorless flight research, 1972

The proceedings of a symposium on motorless flight research are presented. The subjects discussed are: (1) glider aerodynamic and design, (2) instrumentation, (3) structural concepts and materials, (4) soaring meteorology, (5) self-launching and ultralight sailplanes, and (6) performance testing.

Nash-Webber, J. L.↗
NASA NTRS1986

Mission adaptive wing soars at NASA Facility

Research pilots have flown the Mission Adaptive Wing (MAW) aircraft, a highly modified F-111 jet fighter, from subsonic speeds up to Mach 1.4 in initial flight tests. The inital test flights are clearing the envelope with the wings flexed at various curvatures. This process allows further research data to be safely gathered so that designers of future variable camber wing aircraft have the best information possible. The altitude envelope was cleared from 27,500 down to 7,500 feet where denser air can cause more stress on the aircraft. Testing with the aircraft was conducted with wing sweep angles of 26 and 58 degrees. At the conclusion of the performance tests in the manual configuration, the system will be reconfigured for automatic mode tests. The limited automatic modes include maneuver camber control where the wings are deflected automatically to the best lift versus drag combination for a particular speed; cruise camber control which can help protect the aircraft from high G stresses; and maneuver enhancement/gust alleviation which is designed to improve the aircraft's up and down movement response to pilot commands and reduce the aircraft response to turbulence.

Rahn, D.↗
NASA NTRS2005

Performance Monitoring and Assessment of Neuro-Adaptive Controllers for Aerospace Applications Using a Bayesian Approach

Modern exploration missions require modern control systems-control systems that can handle catastrophic changes in the system's behavior, compensate for slow deterioration in sustained operations, and support fast system ID. Adaptive controllers, based upon Neural Networks have these capabilities, but they can only be used safely if proper verification & validation (V&V) can be done. In this paper we present our V & V approach and simulation result within NASA's Intelligent Flight Control Systems (IFCS).

Gupta, Pramod↗
NASA NTRS2006

Space Shuttle Thermal Protection System Repair Flight Experiment Induced Contamination Impacts

NASA s activities to prepare for Flight LF1 (STS-114) included development of a method to repair the Thermal Protection System (TPS) of the Orbiter s leading edge should it be damaged during ascent by impacts from foam, ice, etc . Reinforced Carbon-Carbon (RCC) is used for the leading edge TPS. The repair material that was developed is named Non- Oxide Adhesive eXperimental (NOAX). NOAX is an uncured adhesive material that acts as an ablative repair material. NOAX completes curing during the Orbiter s descent. The Thermal Protection System (TPS) Detailed Test Objective 848 (DTO 848) performed on Flight LF1 (STS-114) characterized the working life, porosity void size in a micro-gravity environment, and the on-orbit performance of the repairs to pre-damaged samples. DTO 848 is also scheduled for Flight ULF1.1 (STS-121) for further characterization of NOAX on-orbit performance. Due to the high material outgassing rates of the NOAX material and concerns with contamination impacts to optically sensitive surfaces, ASTM E 1559 outgassing tests were performed to determine NOAX condensable outgassing rates as a function of time and temperature. Sensitive surfaces of concern include the Extravehicular Mobility Unit (EMU) visor, cameras, and other sensors in proximity to the experiment during the initial time after application. This paper discusses NOAX outgassing characteristics, how the amount of deposition on optically sensitive surfaces while the NOAX is being manipulated on the pre-damaged RCC samples was determined by analysis, and how flight rules were developed to protect those optically sensitive surfaces from excessive contamination where necessary.

Smith, Kendall A.↗