Search NASA⌕ Search

SEARCH · Search NASA

Results for “SPECTRAL NOISE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Optimized tracking of RF carriers with phase noise, including Pioneer 10 results

The ability to track very weak signals from distant spacecraft is limited by the phase instabilities of the received signal and of the local oscillator employed by the receiver. These instabilities ultimately limit the minimum loop bandwidth that can be used in a phase-coherent receiver, and hence limit the ratio of received carrier power to noise spectral density which can be tracked phase coherently. A method is presented for near real time estimation of the received carrier phase and additive noise spectrum, and optimization of the phase locked loop bandwidth. The method was used with the breadboard Deep Space Network (DSN) Advanced Receiver to optimize tracking of very weak signals from the Pioneer 10 spacecraft, which is now more distant that the edge of the solar system. Tracking with bandwidths of 0.1 Hz to 1.0 Hz reduces tracking signal threshold and increases carrier loop signal to noise ratio (SNR) by 5 dB to 15 dB compared to the 3 Hz bandwidth of the receivers now used operationally in the DSN. This will enable the DSN to track Pioneer 10 until its power sources fails near the end of the century.

Vilnrotter, V. A.↗

Design criteria for noncoherent Gaussian channels with MFSK signaling and coding

This paper presents data and criteria to assess and guide the design of modems for coded noncoherent communication systems subject to practical system constraints of power, bandwidth, noise spectral density, coherence time, and number of orthogonal signals M. Three basic receiver types are analyzed for the noncoherent multifrequency-shift keying (MFSK) additive white Gaussian noise channel: hard decision, unquantized (optimum), and quantized (soft decision). Channel capacity and computational cutoff rate are computed for each type and presented as functions of the predetection signal-to-noise ratio and the number of orthogonal signals. This relates the channel constraints of power, bandwidth, coherence time, and noise power to the optimum choice of signal duration and signal number.

Butman, S. A.↗

Aircraft Noise Prediction Program (ANOPP) Fan Noise Prediction for Small Engines

The Fan Noise Module of ANOPP is used to predict the broadband noise and pure tones for axial flow compressors or fans. The module, based on the method developed by M. F. Heidmann, uses empirical functions to predict fan noise spectra as a function of frequency and polar directivity. Previous studies have determined the need to modify the module to better correlate measurements of fan noise from engines in the 3000- to 6000-pound thrust class. Additional measurements made by AlliedSignal have confirmed the need to revise the ANOPP fan noise method for smaller engines. This report describes the revisions to the fan noise method which have been verified with measured data from three separate AlliedSignal fan engines. Comparisons of the revised prediction show a significant improvement in overall and spectral noise predictions.

Hough, Joe W.↗

Performance of mean-frequency estimators for Doppler radar and lidar

The performance of mean-frequency estimators for Doppler radar and lidar measurements of winds is presented in terms of two basic parameters: Phi, the ratio of the average signal energy per estimate to the spectral noise level; and Omega, which is proportional to the number of independent samples per estimate. For fixed Phi and Omega, the Cramer-Rao bound (CRB) (theoretical best performance) for unbiased estimators of mean frequency (normalized by the spectral width of the signal), signal power, and spectral width are essentially independent of the number of data samples M. For large Phi, the estimators of mean frequency are unbiased and the performance is independent of M. The spectral domain estimators and covariance based estimators are bounded by the approximate period of M. The spectral domain estimators and covariance based estimators are bounded by the approximate periodogram CRB. The standard deviation of the maximum-likelihood estimator approaches the exact CRB, which can be more than a factor of 2 better than the performance of the spectral domain estimators or covariance-based estimators for typical Omega. For small Phi, the estimators are biased due to the effects of the uncorrelated noise (white noise), which results in uniformly distributed 'bad' estimates. The fraction of bad estimates is a function of Phi and M with weak dependence on the parameter Omega. Simple empirical models describe the standard deviation of the good estimates and the fraction of bad estimates. For Doppler lidar and for large Phi, better performance is obtained by using many low-energy pulses instead of one pulse with the same total energy. For small Phi, the converse is true.

Frehlich, R. G.↗

Investigation of Physical Mechanisms for Jet Noise Reduction by Plug Nozzle Porosity

This paper presents the results of a computational study on porous-plug nozzles for their eventual application in reducing takeoff noise levels for supersonic civil transport. The study explores a wide range of porous-plug geometries, encompassing variations in hole size, plug length and porosity. Computational fluid dynamics (CFD) analyses are employed in concert with an advanced automated mesh refinement (AMR) scheme, Sketch-to-Solution (S2S), to investigate porous plug nozzle design strategies that may diminish shock strength, broad-band shock noise (BBSN), flow separation, and other undesirable characteristics associated with high takeoff noise levels. A selected subset of the porous-plug nozzles that were analyzed computationally were manufactured at subscale using stereolithography 3D printing. These nozzles were tested experimentally, obtaining far-field noise spectral data and schlieren flow visualization pictures. Detailed comparisons between CFD predictions and experimental results were conducted. These comparisons focus on gaining a better understanding of the underlying physical mechanisms responsible for noise reduction with the porous plugs relative to corresponding solid plugs.

computational fluid dynamics↗

Investigation of Physical Mechanisms for Jet Noise Reduction by Plug Nozzle Porosity

This paper presents the results of a computational study on porous-plug nozzles for their eventual application in reducing takeoff noise levels for supersonic civil transport. The study explores a wide range of porous-plug geometries, encompassing variations in hole size, plug length and porosity. Computational fluid dynamics (CFD) analyses are employed in concert with an advanced automated mesh refinement (AMR) scheme, Sketch-to-Solution (S2S), to investigate porous plug nozzle design strategies that may diminish shock strength, broad-band shock noise (BBSN), flow separation, and other undesirable characteristics associated with high takeoff noise levels. A selected subset of the porous-plug nozzles that were analyzed computationally were manufactured at subscale using stereolithography 3D printing. These nozzles were tested experimentally, obtaining far-field noise spectral data and schlieren flow visualization pictures. Detailed comparisons between CFD predictions and experimental results were conducted. These comparisons focus on gaining a better understanding of the underlying physical mechanisms responsible for noise reduction with the porous plugs relative to corresponding solid plugs.

Nozzles↗

Optical motion sensor for resonant-bar gravitational wave antennas

An experiment is described in which an optical method was used to measure fluctuations in the separation between two mirrors of a Fabry-Perot sensor cavity. Noise measurements were made to determine the sensitivity of this device to vibration amplitudes in the frequency range 1.1-2.1 kHz, which is of interest for resonant-bar gravitational wave antennas. The rms spectral noise density for length fluctuations in this range was sq rt 3.7 x 10 exp -15 m/Hz and can be related to electronic noise of the circuitry plus vibrational noise from the environment. The cavity finesse was relatively low at 117, and the power dissipated in the mirrors was estimated to be 1.9 micro-W. On a multimode gravitational wave detector, the sensor cavity would be formed by one reference mirror and by one mirror mounted on the last resonator. For a 1200-kg bar, 1.2-g last resonator system operating at 1600 Hz the sensor described here would exhibit a noise temperature of 18 micro-K; the resolution in h in the case of negligible thermal noise from the mechanical system would be sq rt 3.7 x 10 exp -18/Hz. Improvements in the sensitivity in a quiet antenna-like environment should be possible with higher finesse mirrors.

Richard, J.-P.↗

Broadband Noise Prediction of Two Small Hovering Rotors using FUN3D-ANOPP2

A computational study was performed on two small hovering rotors, the ideally twisted rotor and the optimum hovering 2-bladed rotor, using FUN3D-ANOPP2. The effects of different inviscid upwinding techniques and temporal resolutions on aerodynamic performance and acoustic prediction were compared against experimental data obtained in the Small Hover Anechoic Chamber facility at the NASA Langley Research Center. Decreasing the numerical dissipation with 𝜅 tuning or by using a higher-order inviscid flux reconstruction scheme was shown to improve aerodynamic performance predictions when compared to measured data for most cases. The effect of dissipation on the vorticity field was also seen to influence the amount of turbulence surrounding the vortex core of the first blade-vortex interaction (BVI), the coherence of the second and higher BVI vortex cores, and the downstream breakdown of the rotor wake for both rotor geometries. Tonal and broadband noise predictions from simulation cases with lower dissipation were seen to agree better with the experiment for the ideally twisted rotor, whereas temporal resolution differences had negligible impact on the broadband noise results. Similar fundamental BPF directivity patterns were obtained by all simulation cases for the optimum hovering 2-bladed rotor, while the most accurate 2*BPF directivity trend, compared to the experiment, was predicted by the lower-dissipation case at the coarse temporal resolution, albeit with an amplitude underprediction. Broadband noise spectral roll-off behavior was seen to occur at a higher frequency when using a finer temporal resolution for the optimum hovering 2-bladed rotor, unlike for the ideally twisted rotor geometry. The broadband noise prediction for the optimum hovering 2-bladed rotor from the higher-dissipation case at the coarse temporal resolution was also seen to predict a tone centered around approximately 8.5 kHz, which was similar in amplitude to the measured tone around 16.5 kHz.

Christopher S. Thurman↗

State of Jet Noise Prediction-NASA Perspective

This presentation covers work primarily done under the Airport Noise Technical Challenge portion of the Supersonics Project in the Fundamental Aeronautics Program. To provide motivation and context, the presentation starts with a brief overview of the Airport Noise Technical Challenge. It then covers the state of NASA s jet noise prediction tools in empirical, RANS-based, and time-resolved categories. The empirical tools, requires seconds to provide a prediction of noise spectral directivity with an accuracy of a few dB, but only for axisymmetric configurations. The RANS-based tools are able to discern the impact of three-dimensional features, but are currently deficient in predicting noise from heated jets and jets with high speed and require hours to produce their prediction. The time-resolved codes are capable of predicting resonances and other time-dependent phenomena, but are very immature, requiring months to deliver predictions without unknown accuracies and dependabilities. In toto, however, when one considers the progress being made it appears that aeroacoustic prediction tools are soon to approach the level of sophistication and accuracy of aerodynamic engineering tools.

Bridges, James E.↗

Microwave beamed power technology improvement

The magnetron directional amplifier was tested for (1) phase shift and power output as a function of gain, anode current, and anode voltage, (2) background noise and harmonics in the output, (3) long life potential of the magnetron cathode, and (4) high operational efficiency. Examples of results were an adequate range of current and voltage over which 20 dB of amplification could be obtained, spectral noise density 155 dB below the carrier, 81.7% overall efficiency, and potential cathode life of 50 years in a design for solar power satellite use. A fabrication method was used to fabricate a 64 slot, 30 in square slotted waveguide array module from 0.020 in thick aluminum sheet. The test results on the array are discussed.

Brown, W. C.↗

GPS high dynamic receiver tracking demonstration results

Demonstration results are presented for a high dynamic GPS receiver. The receiver tested is a breadboard unit capable of tracking one simulated satellite signal in pseudorange and range rate. The receiver makes approximate maximum likelihood estimates of pseudorange and range rate each 20 ms, and tracks these observables using a third order filter with a time constant of 0.14 s. Carrier phase is not tracked, which eliminates the typical failure mode of loss of carrier lock associated with PLLs at high dynamics. The receiver tracks with pseudorange lag errors of under 0.06 m when subjected to simulated 50 g turns with 40 g/s peak jerk. Pseudorange errors due to receiver noise alone are approximately 0.6 m rms at a carrier power to noise spectral density ratio of 34 dB-Hz. The tracking threshold SNR is approximately 28 dB-Hz, which provides 12 dB margin relative to the 40 dB-Hz that occurs with minimum specified satellite signal strength, 3.5 dB system noise figure, and 0 dBi antenna gain.

Hurd, W. J.↗

ADDRAS - An integrated systems approach

NASA-Langley's Acoustics Division Data Reduction and Analysis System (ADDRAS) computes far-field noise spectral estimates on the basis of weather, aircraft state and position, and acoustic data sets. The structure and function of ADDRAS has been primarily determined by rotorcraft flyover test design, data acquisition, and data flow criteria. The RIM relational database management software is used to organize all noise test data for ADDRAS.

Becker, Lawrence E.↗

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Vonglahn, U.↗

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Von Glahn, U.↗

Design of sidewall treatment of cabin noise control of a twin engine turboprop aircraft

An analytical procedure was used to predict the noise transmission into the cabin of a twin engine general aviation aircraft. This model was then used to optimize the interior A weighted noise levels to an average value of about 85 dBA. The surface pressure noise spectral levels were selected utilizing experimental flight data and empirical predictions. The add on treatments considered in this optimization study include aluminum honeycomb panels, constrained layer damping tape, porous acoustic blankets, acoustic foams, septum barriers and limp trim panels which are isolated from the vibration of the main sidewall structure. To reduce the average noise level in the cabin from about 102 kBA (baseline) to 85 dBA (optimized), the added weight of the noise control treatment is about 2% of the total gross takeoff weight of the aircraft.

Vaicaitis, R.↗

Contra-Rotating Open Rotor Tone Noise Prediction

Reliable prediction of contra-rotating open rotor (CROR) noise is an essential element of any strategy for the development of low-noise open rotor propulsion systems that can meet both the community noise regulations and the cabin noise limits. Since CROR noise spectra typically exhibits a preponderance of tones, significant efforts have been directed towards predicting their tone spectra. To that end, there has been an ongoing effort at NASA to assess various in-house open rotor tone noise prediction tools using a benchmark CROR blade set for which significant aerodynamic and acoustic data had been acquired in wind tunnel tests. In the work presented here, the focus is on the near-field noise of the benchmark open rotor blade set at the cruise condition. Using an analytical CROR tone noise model with input from high-fidelity aerodynamic simulations, detailed tone noise spectral predictions have been generated and compared with the experimental data. Comparisons indicate that the theoretical predictions are in good agreement with the data, especially for the dominant CROR tones and their overall sound pressure level. The results also indicate that, whereas individual rotor tones are well predicted by the linear sources (i.e., thickness and loading), for the interaction tones it is essential that the quadrupole sources be included in the analysis.

Propeller Noise↗

Fan Database and Web-tool for Choosing Quieter Spaceflight Fans

One critical aspect of designing spaceflight hardware is the selection of fans to provide the necessary cooling. And with efforts to minimize cost and the tendancy to be conservative with the amount of cooling provided, it is easy to choose an overpowered fan. One impact of this is that the fan uses more energy than is necessary. But, the more significant impact is that the hardware produces much more acoustic noise than if an optimal fan was chosen. Choosing the right fan for a specific hardware application is no simple task. It requires knowledge of cooling requirements and various fan performance characteristics as well as knowledge of the aerodynamic losses of the hardware in which the fan is to be installed. Knowledge of the acoustic emissions of each fan as a function of operating condition is also required in order to choose a quieter fan for a given design point. The purpose of this paper is to describe a database and design-tool that have been developed to aid spaceflight hardware developers in choosing a fan for their application that is based on aerodynamic performance and reduced acoustic emissions as well. This web-based-tool provides a limited amount of fan-data, provides a method for selecting a fan based on its projected operating point, and also provides a method for comparing and contrasting aerodynamic performance and acoustic data from different fans. Drill-down techniques are used to display details of the spectral noise characteristics of the fan at specific operation conditions. The fan aerodynamic and acoustic data were acquired at Ames Research Center in the Experimental Aero-Physics Branch's Anechoic Chamber. Acoustic data were acquired according to ANSI Standard S12.11-1987, "Method for the Measurement of Noise Emitted by Small Air-Moving Devices." One significant improvement made to this technique included automation that allows for a significant increase in flow-rate resolution. The web-tool was developed at Johnson Space Center and is based on the web-development application, SEQUEL, which includes graphics and drill-down capabilities. This paper will describe the type and amount of data taken for the fans and will give examples of this data. This paper will also describe the data-tool and gives examples of how it can be used to choose quieter fans for use in spaceflight hardware.

Allen, Christopher S.↗