SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Device, which operates from 28 V dc, has four sections, a preregulator, a dc-to-dc converter, a current regulator, and a high voltage starter. The unique characteristics of the individual sections are described.
Beryllium fracture toughness test specimens were fatigue cracked using reversed cycling with a compression load two to three times the tension load. In worked beryllium, textures may be produced which result in fatigue cracks that are out of plane with the starter notch. Specimens of hot pressed stock exhibited load displacement records which were nonlinear throughout their course. Fracture specimens of both hot pressed and forged stock showed essentially no reduction of thickness and the fracture surfaces were flat and normal to the load axis. However, the stress intensity factor at maximum load increased with decreasing thickness. Load-displacement and electric potential records for the hot pressed beryllium specimens exhibited several anomalies such as negative residual crack mouth displacements and a decrease in electrical potential with increasing load.
The onboard navigational and alignment routines used during the nonthrusting phases of an Apollo mission are discussed as to their limitations, and alternate approaches that have more desirable capabilities are presented. A more efficient procedure for solving Kepler's equation, which is used in the calculation of Kepler's problem and Lambert's problem is included, and a sixth-order predictor scheme with a Runge-Kutta starter is recommended for numerical integration. The extension of the rendezvous navigation state to include angle biases and the use of a fixed coordinate system is also evaluated.
The integrated engine-generator concept of locating an electric generator inside an aircraft turbojet or turbofan engine concentric with, and driven by, one of the main engine shafts is discussed. When properly rated, the generator can serve as an engine starter as well as a generator of electric power. The electric power conversion equipment and generator controls are conveniently located in the aircraft. Preliminary layouts of generators in a large engine together with their physical sizes and weights indicate that this concept is a technically feasible approach to aircraft secondary power.
An integrated engine-generator for aircraft secondary power generation is described. The concept consists of an electric generator located inside a turbojet or turbofan engine and both concentric with and driven by one of the main engine shafts. The electric power conversion equipment and generator controls are located in the aircraft. When properly rated, the generator serves as an engine starter as well as a source of electric power. This configuration reduces or eliminates the need for an external gear box on the engine and permits reduction in the nacelle diameter.
Pilot tests were run to determine the applicability of the concepts of linear elastic fracture mechanics (LEFM) to the description of the mechanical behavior of initially cracked specimens of advanced fiber composite laminates. It was found that the failure mechanisms in such specimens were largely crack-dominated and that LEFM procedures were applicable even when the apparent failure mechanism was not explicitly dominated by a starter crack.
Design studies were conducted for an integral lift fan engine utilizing the Lycoming 502 fan core with the final MQT power turbine. The fan is designed for a 12.5 bypass ratio and 1.25:1 pressure ratio, and provides supercharging for the core. Maximum sea level static thrust is 8370 pounds with a specific fuel consumption of 0.302 lb/hr-lb. The dry engine weight without starter is 1419 pounds including full-length duct and sound-attenuating rings. The engine envelope including duct treatment but not localized accessory protrusion is 53.25 inches in diameter and 59.2 inches long from exhaust nozzle exit to fan inlet flange. Detailed analyses include fan aerodynamics, fan and reduction gear mechanical design, fan dynamic analysis, engine noise analysis, engine performance, and weight analysis.
The integrated engine-generator concept consists of an electric generator located inside a turbojet or turbofan engine and both concentric with and driven by one of the main engine shafts. The electric power-conversion equipment and generator controls are conveniently located in the aircraft. When properly rated, the generator serves as an engine starter as well as a source of electric power. The available generating capacity permits use of electrically driven engine accessories. This reduces or eliminates the need for an external gearbox on the engine, thereby simplifying the engine and nacelle assembly and increasing aircraft design flexibility. The nacelle diameter can then be decreased, resulting in less aerodynamic drag and reduced takeoff gross weight.
The refan JT8D-109 performance and stability characteristics are reported as determined from sea level testing, altitude testing, and DC-9 flight testing. The test results are summarized as follows: (1) TSFC at SLS achieved design goal of 12.66 percent reduction. (2) TSFC at altitude average cruise power 0.5 percent higher than design goal, (3) TSFC at altitude maximum cruise power 1.7-3.7 percent higher than design goal, (4) ground starting consistent with JT8D-9 base engine, (5) successful flight starts without starter assist, (6) transient surge margin equivalent to JT8D-9, (7) stable engine operation with inlet distortion, and (8) stable engine operation during snap acceleration and deceleration. A flight idle setting is required for acceptable aborted-landing go-around acceleration time due to increase in low-rotor moment of inertia, and a performance improvement program should be conducted as part of any future certification program.
The author has identified the following significant results. A variable date starter model for spring wheat depending on temperature was more precise than a fixed date model. The same conclusions for fall-planted wheat were not reached. If the largest and smallest of eight temperatures were used to estimate daily maximum and minimum temperatures; respectively, a 1-4 F bias would be introduced into these extremes. For Kansas, a reduction of 0.5 bushels/acre in the root-mean-square-error between model and SRS yields was achieved by a six fold increase (7 to 42) in the density of weather stations. An additional reduction of 0.3 b/A was achieved by incorporating losses due to rusts in the model.
The paper describes the design and capabilities of a compact multichannel electrochemical unit devised to detect and automatically indicate detection time length of bacteria. By connecting this unit to a strip-chart recorder, a permanent record is obtained of the end points and growth curves for each of eight channels. The experimental setup utilizing the multichannel unit consists of a test tube (25 by 150 mm) containing a combination redox electrode plus 18 ml of lauryl tryptose broth and positioned in a 35-C water bath. Leads from the electrodes are connected to the multichannel unit, which in turn is connected to a strip-chart recorder. After addition of 2.0 ml of inoculum to the test tubes, depression of the push-button starter activates the electronics, timer, and indicator light for each channel. The multichannel unit is employed to test tenfold dilutions of various members of the Enterobacteriaceae group, and a typical dose-response curve is presented.
Training manual used for preflight conditioning of NASA astronauts is written for audience with diverse backgrounds and interests. It suggests programs for various levels of fitness, including sample starter programs, safe progression schedules, and stretching exercises. Related information on equipment needs, environmental coonsiderations, and precautions can help readers design safe and effective running programs.
The author has identified the following significant results. The estimates of developmental stage dates from the LACIE adjustable crop calendar (ACC) winter wheat model was somewhat more accurate than the historical crop calendar after jointing. The ACC winter wheat model was not so accurate for the Texas Panhandle as it was for the other areas of the USPG-7 because dry soil conditions delayed fall planting in the Panhandle. Since the LACIE ACC winter wheat model does not contain a moisture term and it was started with historical planting dates, lengthy delays in planting mean that the ACC model will probably be started early and will estimate the developmental growth stages to occur too early in the season. The LACIE ACC spring wheat model was also started early in most areas because of late planting due to fields wet from melting snow and rain. The starter model used to estimate spring planting dates was not accurate under these wet soil conditions and tended to predict the developmental stages to occur earlier than the dates observed in the fields.
New crop calendars are produced for U.S. regions where several years of periodic growth stage observations are available on a CRD basis. Preexisting crop calendars from the LACIE are also collected as are U.S. crop calendars currently being created for the Foreign Commodities Production Forecast project. For the U.S.S.R. and Canada, no new crop calendars are created because no new data are available. Instead, LACIE crop calendars are compared against simulated normal daily temperatures and against the Robertson wheat and Williams barley phenology models run on the simulated normal temperatures. Severe inconsistencies are noted and discussed. For the U.S.S.R., spring and fall planting dates can probably be estimated accurately from satellite or meteorological data. For the starter model problem, the Feyerherm spring wheat model is recommended for spring planted small grains, and the results of an analysis are presented. For fall planted small grains, use of normal planting dates supplemented by spectral observation of an early stage is recommended. The importance of nonmeteorological factors as they pertain to meteorological factors in determining fall planting is discussed. Crop calendar data available at the Johnson Space Center for the U.S., U.S.S.R., Canada, and other countries are inventoried.
A plan is detailed for a supplemental experiment to evaluate several crop growth stage models and crop starter models. The objective of this experiment is to provide timely information to aid in understanding crop calendars and to provide data that will allow a selection between current crop calendar models.
Risk assessment, safety analysis of the automotive stirling engine (ASE) mod I, design criteria and materials properties for the ASE mod I and reference engines, combustion are flower development, and the mod I engine starter motor are discussed. The stirling engine system, external heat system, hot engine system, cold engine system, and engine drive system are also discussed.
Mechanism enables controlled release of two rotating objects. Mechanism applicable to some kinds of motor starters, drive shafts, or other drive systems released while rotating.
Today's benchmark system for the Boeing 757/767/A310 airplanes and future trends in hydromechanical aircraft power generating systems are discussed. The 757/767/A310 system represents the commercial state of the art and the direction in which Sundstrand Corp. is headed, particularly in regard to weight reduction. Sundstrand introduced microprocessor control in an in service system in the Boeing 767 and was the first to use databus communications between the controls. Plans to develop this technology are briefly discussed. Alternative ways to produce and use power in aircraft are discussed. The integrated starter drive is discussed.