Search NASA⌕ Search

SEARCH · Search NASA

Results for “STOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

STOL propulsion systems

The selection and the characteristics of quiet, clean propulsion systems for STOL aircraft are discussed. Engines are evaluated for augmentor wing and externally blown flap STOL aircraft with the engines located both under and over the wings. Some supporting test data are presented. Optimum engines are selected based on achieving the performance, economic, acoustic, and pollution goals presently being considered for future STOL aircraft. The data and results presented were obtained from a number of contracted studies and some supporting NASA inhouse programs, most of which began in early 1972. The contracts include: (1) two aircraft and mission studies, (2) two propulsion system studies, (3) the experimental and analytic work on the augmentor wing, and (4) the experimental programs on Q-Fan. Engines are selected and discussed based on aircraft economics using the direct operating cost as the primary criterion. This cost includes the cost of the crew, fuel, aircraft, and engine maintenance and depreciation.

Denington, R. J.↗
NASA NTRS1973

Aspects of investigating STOL noise using large-scale wind-tunnel models.

The applicability of the NASA Ames 40- by 80-foot wind tunnel for acoustic research on STOL concepts has been investigated. The acoustic characteristics of the wind-tunnel test section have been studied with calibrated acoustic sources. Acoustic characteristics of several large-scale STOL models have been studied in both the free-field and wind-tunnel acoustic environments. The results of these studies indicate that the acoustic characteristics of large-scale STOL models can be measured in the wind tunnel if the test section acoustic environment and model acoustic similitude are taken into consideration. The reverberant field of the test section must be determined with an acoustically similar noise source. A directional microphone, a phased array of microphones, and extrapolation of near-field data to far-field are some of the techniques being explored as possible solutions to the directivity loss in a reverberant field. The model sound pressure levels must be of sufficient magnitude to be distinguishible from the wind-tunnel background noise.

Falarski, M. D.↗
NASA NTRS1973

Preliminary assessment of the microwave landing system requirements for STOL operations

The results of an investigation made to assess the Microwave Landing System (MLS) Requirements for use by civil STOL aircraft are described. The principal MLS characteristics investigated in the report were signal accuracy and volume of coverage. The study utilized a nonlinear six-degree-of-freedom digital simulation of a De Havilland Buffalo C-8A aircraft. Fully automatic control of timed curve flight down to touchdown was simulated. Selected MLS accuracy and coverage parameters for the azimuth, primary elevation, flare evelation and DME signals were varied. The resulting STOL aircraft system performance in following a representative curved flight path was statistically determined. Coverage requirements for STOL aircraft operating in the terminal area environment were also investigated.

Burrous, C. N.↗
NASA NTRS1974

Analytical design and simulation evaluation of an approach flight director system for a jet STOL aircraft

A program was undertaken to develop design criteria and operational procedures for STOL transport aircraft. As part of that program, a series of flight tests shall be performed in an Augmentor Wing Jet STOL Aircraft. In preparation for the flight test programs, an analytical study was conducted to gain an understanding of the characteristics of the vehicle for manual control, to assess the relative merits of the variety of manual control techniques available with attitude and thrust vector controllers, and to determine what improvements can be made over manual control of the bare airframe by providing the pilot with suitable command guidance information and by augmentation of the bare airframe dynamics. The objective of the study is to apply closed-loop pilot/vehicle analysis techniques to the analysis of manual flight control of powered-lift STOL aircraft in the landing approach and to the design and experimental verification of an advanced flight director display.

Klein, R. H.↗
NASA NTRS1974

A simulator investigation of engine failure compensation for powered-lift STOL aircraft

A piloted simulator investigation of various engine failure compensation concepts for powered-lift STOL aircraft was carried out at the Ames Research Center. The purpose of this investigation was to determine the influence of engine failure compensation on recovery from an engine failure during the landing approach and on the precision of the STOL landing. The various concepts include: (1) cockpit warning lights to cue the pilot of an engine failure, (2) programmed thrust and roll trim compensation, (3) thrust command and (4) flight-path stabilization. The aircraft simulated was a 150 passenger four-engine, externally blown flap civil STOL transport having a 90 psf wing loading and a .56 thrust to weight ratio. Results of the simulation indicate that the combination of thrust command and flight-path stabilization offered the best engine-out landing performance in turbulence and did so over the entire range of altitudes for which engine failures occurred.

Nieuwenhuijse, A. W.↗
NASA NTRS1974

A STOL airworthiness investigation using a simulation of a deflected slipstream transport. Volume 1: Summary of results and airworthiness implications

A simulator study of short takeoff and landing (STOL) aircraft was conducted using a model of a deflected slipstream transport aircraft. The subjects considered are: (1) the approach, (2) flare and landing, (3) go-around, and (4) takeoff phases of flight. The results are summarized and possible implications with regard to airworthiness criteria are discussed. A data base is provided for future STOL airworthiness requirements and a preliminary indication of potential problem areas is developed. Comparison of the simulation results with various proposed STOL criteria indicates significant deficiencies in many of these criteria.

Stapleford, R. L.↗
NASA NTRS1975

Interior noise considerations for powered-lift STOL aircraft

Powered-jet configuration which are under development for use on STOL aircraft involve impingement of the jet engine exhaust onto wing and flap surfaces. The impinging jet produces higher noise levels at lower frequencies than does the jet alone. These higher levels, together with the close proximity of the engine and flap noise sources to the fuselage sidewall, suggest that the noise levels in these aircraft may be high enough to interfere with passenger comfort. To investigate this possibility, interior noise levels were estimated for both an upper surface blown and an externally blown flap configuration. This paper describes the procedure used to estimate the interior noise levels is described these levels are compared with levels on existing jet aircraft and on ground transportation vehicles. These estimates indicate high levels in the STOL aircraft; therefore, areas of possible improvements in technology for control of STOL interior noise are also discussed.

Barton, C. K.↗
NASA NTRS1975

Exploratory flight investigation of aircraft response to the wing vortex wake generated by the augmentor wing jet STOL research aircraft

A brief exploratory flight program was conducted at Ames Research Center to investigate the vortex wake hazard of a powered-lift STOL aircraft. The study was made by flying an instrumented Cessna 210 aircraft into the wake of the augmentor wing jet STOL research aircraft at separation distances from 1 to 4 n.mi. Characteristics of the wake were evaluated in terms of the magnitude of the upset of the probing aircraft. Results indicated that within 1 n.mi. separation the wake could cause rolling moments in excess of roll control power and yawing moments equivalent to rudder control power of the probe aircraft. Subjective evaluations by the pilots of the Cessna 210 aircraft, supported by response measurements, indicated that the upset caused by the wake of the STOL aircraft was comparable to that of a DC-9 in the landing configuration.

Jacobsen, R. A.↗
NASA NTRS1975

Interior noise considerations for powered-lift STOL aircraft

Powered-lift configurations which are currently under development for future use on STOL aircraft involve impingement of the jet engine exhaust onto wing and flap surfaces. Previous studies have suggested that the impinging jet produces higher noise levels at lower frequencies than does the jet alone. These higher levels, together with the close proximity of the engine and flap noise sources to the fuselage sidewall, suggest that the noise levels in these aircraft may be high enough to interfere with passenger comfort. To investigate this possibility, interior noise levels were estimated for both an upper surface blown (USB) and an externally blown flap (EBF) configuration. This paper describes the procedure used to estimate the interior noise levels and compares these levels with levels on existing jet aircraft and on ground transportation vehicles. These estimates indicate high levels in the STOL aircraft; therefore, areas of possible improvements in technology for control of STOL interior noise are also discussed.

Barton, C. K.↗
NASA NTRS1975

Computed lateral rate and acceleration power spectral response of conventional and STOL airplanes to atmospheric turbulence

Power-spectral-density calculations were made of the lateral responses to atmospheric turbulence for several conventional and short take-off and landing (STOL) airplanes. The turbulence was modeled as three orthogonal velocity components, which were uncorrelated, and each was represented with a one-dimensional power spectrum. Power spectral densities were computed for displacements, rates, and accelerations in roll, yaw, and sideslip. In addition, the power spectral density of the transverse acceleration was computed. Evaluation of ride quality based on a specific ride quality criterion was also made. The results show that the STOL airplanes generally had larger values for the rate and acceleration power spectra (and, consequently, larger corresponding root-mean-square values) than the conventional airplanes. The ride quality criterion gave poorer ratings to the STOL airplanes than to the conventional airplanes.

Lichtenstein, J. H.↗
NASA NTRS1976

A flight investigation of piloting techniques and crosswind limitations during visual STOL-type landing operations

A flight research program was undertaken to investigate problems concerned with landing a STOL airplane in crosswind conditions. The program included a study of piloting techniques and crosswind limitations during visual STOL type landing operations. The results indicated that the crosswind was more limiting during the ground roll out than during the airborne phases. The pilots estimated that the crosswind limit for commercial STOL type operations with the test aircraft would be approximately 15 to 20 knots. The pilots thought that the crosswind limits for ground operation might be extended by incorporating wing-lift spoilers, improved nose gear steering, and improved engine response. The pilots agreed that a crosswind landing gear would also be beneficial.

Fisher, B. D.↗
NASA NTRS1976

Operational experience with a powered-lift STOL aircraft

The experience gained in over four years of STOL operations with the augmentor wing research aircraft and the background of operation of other STOL powered-lift aircraft indicate that the use and percent of lift achieved by powered lift have significant effects on the operational characteristics of STOL aircraft and, therefore, on the performance that can be achieved. A brief description of the augmentor wing including the means by which it achieves its powered lift is presented. Specific problem areas relating to the control of longitudinal flight path are discussed as well as the consequences these might have on the design and operation of this class of aircraft. Particular emphasis is given to the approach and landing phase of flight where the consequences of the powered lift are most pronounced, and the resultant characteristics most different from those of conventional aircraft.

Innis, R. C.↗
NASA NTRS1977

Thrust augmentor application for STOL and V/STOL

A general parametric description is suggested for thrust augmentor application to STOL and V/STOL aircraft. The parameters and their relationships are discussed using several aircraft augmentor integration problems. For a STOL transport design, the ram drag is a key consideration, limiting the maximum gross augmentation that can be utilized. Maximizing gross augmentation and balancing the aircraft are key considerations for a V/STOL fighter design. Results from wind tunnel investigations on several different thrust augmentor concepts and system studies on STOL transport designs are also included.

Aiken, T. N.↗
NASA NTRS1979

Identification of a STOL propulsion plant model from flight data

Accurate dynamic models for propulsion system behavior are critical to successful synthesis of STOL autothrottle/autoland control systems. This paper describes the development of a nonlinear dynamic model for the response of a STOL aircraft in the landing/approach configuration. The model is based upon an analysis of the throttle, governor, and turbofan engine components. Model parameters are directly identified from data acquired during a flight of the NASA Augmentor Wing Jet STOL research aircraft. The accuracy of the model and a comparison of results for two engines are described. Various approaches to modeling propulsion system response for complex systems representative of current and near-term aircraft are discussed.

De Hoff, R. L.↗
NASA NTRS1981

A method for determining landing runway length for a STOL aircraft

Based on data obtained from flight tests of the augmentor wing jet STOL research aircraft, a method is proposed for determining the length of the landing runway for powered-lift STOL aircraft. The suggested method determines runway landing length by summing three segments: the touchdown-dispersion distance, the transition distance from touchdown to application of brakes, and the stopping distance after brakes are applied. It is shown how the landing field length can be reduced either through improved autoland system design or by providing the pilot with appropriate information to allow him to identify a "low probability" long or short landing and to execute a go-around. The proposed method appears to determine a safe runway landing length for the STOL application and offers the potential for reducing runway length if great emphasis is placed on a short-runway capability. FAR Parts 25 and 121 appear conservative and suitable for the situation where no great emphasis is placed on reducing the runway length requirement.

Watson, D. M.↗
NASA NTRS1983

STOL wind tunnel test results for a tactical supercruiser

Attention is given to the NASA Langley Research Center's testing of a 10.5 percent-scale supersonic cruiser (supercruiser) aircraft model in its V/STOL wind tunnel, in order to investigate the low speed aerodynamic characteristics of STOL enhancement devices. The STOL devices employed by the supercruiser configuration are high vector angle ramp nozzles, working in conjunction with a remote augmented lift system (RALS), in addition to a canard trim system. Also investigated were thrust reverser/ground plane interaction effects, for the evaluation of landing characteristics. It is noted that STOL approach thrust management requires the use of a partially reversing RALS nozzle which develops approximately 31 percent of main nozzle thrust, and that strong nose-up interactions during ground roll, with reverser operation, may limit dry power engine thrust for braking assistance to about 50 percent of maximum dry power.

Hutchison, R. A.↗
NASA NTRS1986

Flight evaluation of a precision landing task for a powered-lift STOL aircraft

A flight research experiment was conducted with the NASA-Ames Research Center's Quiet Short-Haul Research Aircraft to determine the factors which influence the touchdown distribution for a powered-lift STOL aircraft. The pilots were given two tasks for each of a series of precision approaches flown using a microwave landing system (MLS) in simulated instrument meteorological conditions. They flew the aircraft, with forward vision obscured by a screen, to a 100-ft decision height using a flightpath-oriented, color electronic display and one of four levels of control augmentation. Approaches were flown along a nominal 6 deg glidepath, as well as to calibrated offsets at the decision height to establish a variety of initial conditions for the landing task. The screen was removed at the decision height and the pilot was briefed to land in a 200 foot touchdown zone of the STOLport with a sink rate less than 5 ft/sec. Statistical performance envelopes and pilot ratings are used to describe the results of this experiment. The data generated are expected to be useful for establishing STOL aircraft operating requirements and STOL MLS approach criteria.

Watson, D. M.↗
NASA NTRS1986

Recommendations for ground effects research for V/STOL and STOL aircraft and associated equipment for large scale testing

The current understanding of the effects of ground proximity on V/STOL and STOL aircraft is reviewd. Areas covered include (1) single jet suckdown in hover, (2) fountain effects on multijet configurations, (3) STOL ground effects including the effect of the ground vortex flow field, (4) downwash at the tail, and (5) hot gas ingestion in both hover and STOL operation. The equipment needed for large scale testing to extend the state of the art is reviewed and developments in three areas are recommended as follows: (1) improve methods for simulating the engine exhaust and inlet flows; (2) develop a model support system that can simulate realistic rates of climb and descent as well as steady height operation; and (3) develop a blowing BLC ground board as an alternative to a moving belt ground board to properly simulate the flow on the ground.

Kuhn, Richard E.↗