Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Reynolds shear stress measurements in a separated boundary layer flow

Turbulence measurements were obtained for two cases of boundary layer flow with an adverse pressure gradient, one attached and the other separated. A three-component laser Doppler velocimeter system was used to measure three mean velocity components, all six Reynolds stress components, and all ten velocity triple product correlations. Independent measurements of skin-friction obtained with a laser oil-flow interferometer were used to examine the law of the wall in adverse pressure gradient flows where p(+) is less than 0.05. Strong similiarities were seen between the two adverse pressure gradient flows and free shear layer type flows. Eddy viscosities, dissipation rates, and pressure-strain rates were deduced from the data and compared to various turbulence modeling assumptions.

Driver, David M.↗
NASA NTRS1997

Residual Stress Measurements After Proof and Flight: ETP-0403

The intent of this testing was to evaluate the residual stresses that occur in and around the attachment details of a case stiffener segment that has been subjected to flight/recovery followed by proof loading. Not measured in this test were stresses relieved at joint disassembly due to out-of-round and interference effects, and those released by cutting the specimens out of the case segment. The test article was lightweight case stiffener segment 1U50715, S/N L023 which was flown in the forward stiffener position on flight SRM 14A and in the aft position on flight SRM24A. Both of these flights were flown with the 3 stiffener ring configuration. Stiffener L023 had a stiffener ring installed only on the aft stub in its first flight, and it had both rings installed on its second flight. No significant post flight damage was found on either flight. Finally, the segment was used on the DM-8 static test motor in the forward position. No stiffener rings were installed. It had only one proof pressurization prior to assignment to its first use, and it was cleaned and proof tested after each flight. Thus, the segment had seen 3 proof tests, two flight pressurizations, and two low intensity water impacts prior to manufacturing for use on DM-8. On DM-8 it received one static firing pressurization in the horizontal configuration. Residual stresses at the surface and in depth were evaluated by both the x-ray diffraction and neutron beam diffraction methods. The x-ray diffraction evaluations were conducted by Technology for Energy Corporation (TEC) at their facilities in Knoxville, TN. The neutron beam evaluations were done by Atomic Energy of Canada Limited (AECL) at the Chalk River Nuclear Laboratories in Ontario. The results showed general agreement with relatively high compressive residual stresses on the surface and moderate to low subsurface tensile residual stresses.

Webster, Ronald L..↗
NASA NTRS2017

Mechanical Stress Measurement During Thin-Film Fabrication

A method and system are provided for determining mechanical stress experienced by a film during fabrication thereof on a substrate positioned in a vacuum deposition chamber. The substrate's first surface is disposed to have the film deposited thereon and the substrate's opposing second surface is a specular reflective surface. A portion of the substrate is supported. An optical displacement sensor is positioned in the vacuum deposition chamber in a spaced-apart relationship with respect to a portion of the substrate's second surface. During film deposition on the substrate's first surface, displacement of the portion of the substrate's second surface is measured using the optical displacement sensor. The measured displacement is indicative of a radius of curvature of the substrate, and the radius of curvature is indicative of mechanical stress being experienced by the film.

Broadway, David M.↗
NASA NTRS1975

Psychological stress measurement through voice output analysis

Audio tape recordings of selected Skylab communications were processed by a psychological stress evaluator. Strip chart tracings were read blind and scores were assigned based on characteristics reported by the manufacturer to indicate psychological stress. These scores were analyzed for their empirical relationships with operational variables in Skylab judged to represent varying degrees of situational stress. Although some statistically significant relationships were found, the technique was not judged to be sufficiently predictive to warrant its use in assessing the degree of psychological stress of crew members in future space missions.

Older, H. J.↗
NASA NTRS1992

On the use of the hole-drilling technique for residual stress measurements in thin plates

The strain gage blind hole-drilling technique may be used to determine residual stresses at and below the surface of components. In this paper, the hole-drilling analysis methodology for thick plates is reviewed, and experimental data are used to evaluate the methodology and to assess its applicability to thin plates. Data on the effects of gage pattern, surface preparation, hole spacing, hole eccentricity, and stress level are also presented.

Hampton, R. W.↗
NASA NTRS1987

Gear tooth stress measurements on the UH-60A helicopter transmission

The U.S. Army UH-60A (Black Hawk) 2200-kW (3000-hp) class twin-engine helicopter transmission was tested at the NASA Lewis Research Center. Results from these experimental (strain-gage) stress tests will enhance the data base for gear stress levels in transmissions of a similar power level. Strain-gage measurements were performed on the transmission's spiral-bevel combining pinions, the planetary Sun gear, and ring gear. Tests were performed at rated speed and at torque levels 25 to 100 percent that of rated. One measurement series was also taken at a 90 percent speed level. The largest stress found was 760 MPa (110 ksi) on the combining pinion fillet. This is 230 percent greater than the AGMA index stress. Corresponding mean and alternating stresses were 300 and 430 MPa (48 and 62 ksi). These values are within the range of successful test experience reported for other transmissions. On the fillet of the ring gear, the largest stress found was 410 MPa (59 ksi). The ring-gear peak stress was found to be 11 percent less than an analytical (computer simulation) value and it is 24 percent greater than the AGMA index stress. A peak compressive stress of 650 MPa (94 ksi) was found at the center of the Sun gear tooth root.

Oswald, Fred B.↗
NASA NTRS1987

Residual stress measurement in silicon sheet by shadow moire interferometry

A shadow moire interferometry technique has been developed to measure residual strain in thin silicon sheet. The curvature of a segment of sheet undergoing four-point bending is analyzed to include the applied bending moments, the in-plane residual stresses, and the 'end effect' of the sheet since it is of finite length. The technique is applied to obtain residual stress distributions for silicon sheet grown by the edge-defined film-fed growth technique.

Kwon, Y.↗
NASA NTRS1988

Review of magnetoacoustic residual stress measurement technique for iron-like ferromagnetic alloys

It is shown that the elastic moduli of ironlike ferromagnetics depends explicitly on the state of 90 deg domain walls: the more 90 deg domain wall area available, the lower the elastic modulus. New experimental results obtained for three types of carbon and pure iron samples are presented. The magnetoacoustic response due to magnetization perpendicular to the uniaxial stress axis is considered as well as the magnetoacoustic response due to magnetization parallel to the uniaxial stress axis.

Namkung, M.↗
NASA NTRS1993

Differential temperature stress measurement employing array sensor with local offset

The instrument has a focal plane array of infrared sensors of the integrating type such as a multiplexed device in which a charge is built up on a capacitor which is proportional to the total number of photons which that sensor is exposed to between read-out cycles. The infrared sensors of the array are manufactured as part of an overall array which is part of a micro-electronic device. The sensor achieves greater sensitivity by applying a local offset to the output of each sensor before it is converted into a digital word. The offset which is applied to each sensor will typically be the sensor's average value so that the digital signal which is periodically read from each sensor of the array corresponds to the portion of the signal which is varying in time. With proper synchronization between the cyclical loading of the test object and the frame rate of the infrared array the output of the A/D converted signal will correspond to the stress field induced temperature variations. A digital lock-in operation may be performed on the output of each sensor in the array. This results in a test instrument which can rapidly form a precise image of the thermoelastic stresses in an object.

Lesniak, Jon R.↗
NASA NTRS1971

A borehole jack for deformability, strength, and stress measurements in a 2-inch borehole

A borehole jack devised for lunar exploration is described and results of its use in simulated lunar solids are presented. A hydraulic cylinder mounted between two stiff plates acts to spread the plates apart against the borehole walls when pressured. The spreading is measured by a displacement transducer and the load is measured hydraulically. The main improvement over previous instruments is the increased stroke, which allows large deformations of the borehole. Twenty-eight pistons are used to obtain a high hydraulic efficiency, and three return pistons are also provided. Pressure-deformation curves were obtained for each test on Lunar Soil Simulant No. 2, a light gray silty basalt powder.

Goodman, R. E.↗
NASA NTRS1982

Scientific opportunities using satellite surface wind stress measurements over the ocean

Scientific opportunities that would be possible with the ability to collect wind data from space are highlighted. Minimum requirements for the space platform and ground data reduction system are assessed. The operational uses that may develop in government and commercial applications of these data are reviewed. The opportunity to predict the large-scale ocean anomaly called El Nino is highlighted.

Source record↗
NASA NTRS1987

Acoustic radiation stress measurement

Ultrasonic radio frequency tone-bursts are launched into a sample of material tested. The amplitude of the tone-bursts and the slope of the resulting static displacement pulses are measured. These measurements are used to calculate the nonlinearities of the materials.

Cantrell, John H., Jr.↗
NASA NTRS1988

Voice-stress measure of mental workload

In a planned experiment, male subjects between the age of 18 and 50 will be required to produce speech while performing various tasks. Analysis of the speech produced should reveal which aspects of voice prosody are associated with increased workloads. Preliminary results with two female subjects suggest a possible trend for voice frequency and amplitude to be higher and the variance of the voice frequency to be lower in the high workload condition.

Alpert, Murray↗