SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Large transport approach and landing simulation - direct lift control applied to noise abatement approaches, and supersonic transport handling capabilities
Supersonic transport trajectory optimization example solutions
Supersonic transport fixed base simulator to anticipate integration problems with air traffic control systems
Flight characteristics of supersonic transports during landing approach with large jet transport in flight simulator
Following cancellation of the United States Supersonic Transport program, the status of the technology was assessed carefully and emphasis was put on finding solutions for what were considered the major technical difficulties. In particular, work on the breakthroughs needed to advance the technology was emphasized. Currently, solutions to all major technical problems are identified. Depending on the subject, either the problem is no longer a concern or the steps needed to bring about a solution are mapped out clearly. Throughout the NASA SCR program, important strides were made in the identification of design advances which would greatly improve supersonic airplane fuel efficiency, noise, and other performance and cost affecting parameters. Furthermore, these efforts created an atmosphere in which it was possible for new ideas to flourish and positive inventions to take place such as the variable cycle engine and the blended fuselage. These technical gains show that, given availability of such technology, advanced supersonic transports could be developed that would be economically successful and environmentally acceptable.
This paper presents the results of recent Douglas Aircraft Company integration studies for an advanced supersonic transport. The studies include technology improvements such as superplastic formed and diffusion-bonded titanium sandwich primary structure, composite secondary structure, bicone engine inlet, improved mechanical suppressors based on flight test data, improved aerodynamic efficiency based on wind tunnel test data, and updated performance for both variable-cycle and low-bypass-ratio engines. Technology development requirements for an economically viable and environmentally acceptable advanced supersonic transport are defined through these studies. A new Douglas Aircraft Company baseline supersonic transport designed to carry 350 passengers is defined for cost comparisons.
The rolling moment induced on aircraft models in the wake of a model of a subsonic transport and of a supersonic transport was measured as a function of angle of attack for several configurations. The tests are described and an analysis of the data is given in this memorandum.
To enable commercially viable civil supersonic transport (SST) aircraft, innovative solutions must be developed to meet noise and efficiency requirements for overland flight. This research effort consists of a multidisciplinary team of academic and industrial experts exploring for the first time the potential of small real-time geometric outer mold line (OML) reconfigurations to minimize sonic boom signatures and aircraft drag in response to changing ambient conditions, thereby enabling noise-compliant overland supersonic flight. The team utilizes recent advances in supersonic computational fluid dynamic (CFD) methods, new noise prediction tools, and new design approaches to consider embedded highly energy-dense shape memory alloy (SMA) actuators for local shape modifications to an SST aircraft leading to optimal low boom signature and low drag in different environments. This university-led program will provide strategic leadership toward technology convergence that advances NASA's Aerospace Research Mission Directorate's (ARMD) research objectives with regard to Thrust 2: “Innovation in Commercial Supersonic Aircraft” by exploring for the first time enabling low-boom operation across a range of flight conditions via structural adaptivity, and will promote education of the next generation of engineers. The overall research strategy is to pursue three critical areas: the design of configurations for reducing boom, SMA material development and modeling, and technology feasibility demonstration in a relevant environment. Initially, the team will identify potential applications where structure or geometry adaptivity provides a benefit in noise or drag across the entire flight envelope. For selected applications/structural locations, required OML geometry changes will be determined based on analysis of sonic boom ground signature and drag reduction using new design tools, trade studies, and atmospheric sensing techniques. Designs will be developed and evaluated against requirements on loading, stroke length, and operational temperature. New alloy formulations will be developed tailored for both autonomous and controlled actuation modes. As the SMA material development matures, integrated system-level factors will be investigated. Optimized designs for small-scale distributed adaptivity applications of maximum benefit will then be matured and tested, moving toward demonstration of the innovative technology approaches at a TRL 4-5 and showing that sonic booms can be reduced by reconfiguration on demand.
Supersonic transport instrumentation and flight simulation
Low-speed longitudinal handling qualities of supersonic transport aircraft obtained from a piloted simulator
Fatigue behavior of fusion welded structural assembly with supersonic transport application
Design-range and reserve-fuel requirements of supersonic transport
Increases in supersonic cruise lift drag ratio were sought at Mach numbers 2.2 and 2.7 using wing body planform and thickness blending. Constrained twist and camber optimization was performed in the presence of nacelles. Wing and fuselage thickness distributions were optimized for either minimum volume wave drag or minimum total pressure wave drag. The zero leading edge suction lift drag ratios were determined for three wing planforms. The magnitude of the effect of leading edge suction on attainable lift drag ratio was defined on one planform and estimation of available leading edge suction was made.
Commercial supersonic vehicles of the future will likely use engines with lower bypass ratios, where the design of the internal mixer will have a strong impact on the noise produced by the jet plume. Their exhaust systems may also feature external plugs to improve boattail angle for cruise performance at supersonic speeds. Currently there are no publicly available empirical noise models for such nozzle systems, and insight into their flow fields will help in creating these models. For those attempting to make large eddy simulations and other higher fidelity methods be their main prediction tool, the internally mixed exhaust system is also a good test case when going beyond simple single-stream jets. The turbulent flow statistics of several configurations previously tested for noise and shocks have been measured for flow conditions that can be used in development of empirical models and validating scale-resolving prediction tools. These measurements are presented and briefly analyzed for insights into the noise impacts from the flow impacts observed.
Commercial supersonic vehicles of the future will likely use engines with lower bypass ratios, where the design of the internal mixer will have a strong impact on the noise produced by the jet plume. Their exhaust systems may also feature external plugs to improve boattail angle for cruise performance at supersonic speeds. Currently there are no publicly available empirical noise models for such nozzle systems, and insight into their flow fields will help in creating these models. For those attempting to make large eddy simulations and other higher fidelity methods be their main prediction tool, the internally mixed exhaust system is also a good test case when going beyond simple single-stream jets. The turbulent flow statistics of several configurations previously tested for noise and shocks have been measured for flow conditions that can be used in development of empirical models and validating scale-resolving prediction tools. These measurements are presented and briefly analyzed for insights into the noise impacts from the flow impacts observed.
Most design methods for a low-boom supersonic aircraft were developed for achieving an undertrack low-boom goal at the start of cruise. Attempts were made to design a supersonic aircraft achieving a low-boom goal for multiple azimuthal angles at the start of cruise. One unanswered question is how to define an achievable low-boom goal for multiple azimuthal angles at the start of cruise. This paper proposes a new analysis method to assess off-design low-boom characteristics of a low-boom supersonic transport designed for an undertrack low-boom goal at the start of cruise. This method opens a potentially feasible path for designing a supersonic aircraft that has the desired low-boom characteristics over the primary boom carpet for the entire cruise segment.
The potential benefits of using the fuel heat sink of hydrogen fueled supersonic transports for cooling large portions of the aircraft wing and fuselage are examined. The heat transfer would be accomplished by using an intermediate fluid such as an ethylene glycol-water solution. Some of the advantages of the system are: (1) reduced costs by using aluminum in place of titanium, (2) reduced cabin heat loads, and (3) more favorable environmental conditions for the aircraft systems. A liquid hydrogen fueled, Mach 2.7 supersonic transport aircraft design was used for the reference uncooled vehicle. The cooled aircraft designs were analyzed to determine their heat sink capability, the extent and location of feasible cooled surfaces, and the coolant passage size and spacing.
Most conceptual design methods for low-boom supersonic aircraft are developed for achieving an undertrack low-boom goal at the start of cruise. Although attempts have been made to design a supersonic aircraft achieving a low-boom goal for multiple azimuthal angles at the start of cruise, one unanswered question in inverse design optimization is how to define an achievable low-boom goal for multiple azimuthal angles. This paper proposes a new analysis method to assess off-design low-boom characteristics of a low-boom supersonic transport designed for an undertrack low-boom goal at the start of cruise. This method opens a potentially feasible path for conceptual design of a supersonic aircraft that has desired low-boom characteristics over the primary boom carpet for the entire cruise segment.