Search NASA⌕ Search

SEARCH · Search NASA

Results for “Separation standard”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Pilot Evaluation of a UAS Detect-and-Avoid System's Effectiveness in Remaining Well Clear

Unmanned aircraft will equip with a detect-and-avoid (DAA) system that allows them to comply with the requirement to see and avoid other aircraft, an important layer in the overall set of procedural, strategic and tactical separation methods designed to prevent mid-air collisions. Although the effectiveness of the DAA system will be set to a minimum threshold by regulators, different combinations of algorithms, displays and procedures could be used to meet that minimum. The research presented in this paper indicates the effectiveness of the combined pilot-DAA system as a function of the DAA design requirements and provides data that may be used to model the behavior of pilots when employing such systems. Over the course of two simulations 21 professional UAS pilots evaluated eight different DAA system designs and metrics were collected on their ability to maintain the well clear separation standard. The independent variables were the time horizon at which pilots were alerted to potential losses of well clear, the location of the traffic display, and the tools and informational elements available on the display to aid the pilot in detecting and resolving those potential losses. In the second experiment the UAS encountered two categories of aircraft: those equipped with simulated transponders that could be seen dozens of miles away and those without that were only detectable by a simulated radar within a range of six nautical miles. The data indicate that integrating the traffic display with the primary mission map directly in front of the pilot reduced the frequency of losses of well clear. Improved detection and resolution tools, including explicit maneuver guidance and a trial planning capability, had less of an effect in reducing the frequency of losses but significantly reduced the time in loss when they occurred. The amount of warning time provided to the pilot had a strong effect on their ability to remain well clear: when alerts were first presented with less than about 15 seconds to a predicted loss of well clear pilots were able to maneuver successfully in only 26 percent of encounters, whereas they were about 83 percent successful when they had more than 15 seconds. Pilots' ability to separate from the two categories of aircraft was nearly the same after accounting for the amount of alert time provided in each encounter, although the limited surveillance volume for the non-transponder equipped aircraft meant alerts tended to occur later and therefore were more difficult to resolve.

loss of well clear↗

En route position and time control of aircraft using Kalman filtering of radio aid data

Fixed-time-of-arrival (FTA) guidance and navigation is investigated as a possible technique capable of operation within much more stringent en route separation standards and offering significant advantages in safety, higher traffic densities, and improved scheduling reliability, both en route and in the terminal areas. This study investigated the application of FTA guidance previously used in spacecraft guidance. These FTA guidance techniques have been modified and are employed to compute the velocity corrections necessary to return an aircraft to a specified great-circle reference path in order to exercise en route time and position control throughout the entire flight. The necessary position and velocity estimates to accomplish this task are provided by Kalman filtering of data from Loran-C, VORTAC/TACAN, Doppler radar, radio or barometric altitude,and altitude rate. The guidance and navigation system was evaluated using a digital simulation of the cruise phase of supersonic and subsonic flights between San Francisco and New York City, and between New York City and London.

Mcgee, L. A.↗

Eddy-current sensor measures bolt loading

Thin wire welded to bottom of hole down center of bolt permits measurement of tension in bolt. Bolt lengthens under strain, but wire is not loaded, so gap between wire and eddy-current gap transducer mounted on bolt head indicates bolt loading. Eddy-current transducer could measure gap within 0.05 mm. Method does not require separate "standard" for each bolt type, and is not sensitive to dirt or oil in bolt hole, unlike ultrasonic probes.

Burr, M. E.↗

Air traffic control using a microwave landing system

The performance of air traffic controllers using a simulated microwave landing system to control the landing of STOL aircraft is investigated. In a series of two experiments, controllers were asked to achieve a 60-sec separation between targets at the missed approach point when only two targets were on the simulated radar scope, and in the presence of 25 targets, with up to 10 on the screen at any one time. In both experiments, the presence of a ground wind is found to degrade separation performance, and an increased work load results in even greater separation variability, as the controllers did not have time to convert aircraft distances into times. In addition, curved courses are found to have an effect on performance. It is thus recommended that in order to create a practical air traffic control system with separation standards based on time, as in the MLS, controller work loads should be reduced and aircraft positions should be displayed with respect to time rather than distance.

Gershzohn, G.↗

Feasibility of an onboard wake vortex avoidance system

It was determined that an onboard vortex wake detection system using existing, proven instrumentation is technically feasible. This system might be incorporated into existing onboard systems such as a wind shear detection system, and might provide the pilot with the location of a vortex wake, as well as an evasive maneuver so that the landing separations may be reduced. It is suggested that this system might be introduced into our nation's commuter aircraft fleet and major air carrier fleet and permit a reduction of current landing separation standards, thereby reducing takeoff and departure delays.

Bilanin, Alan J.↗

A study of the interaction between a wake vortex and an encountering airplane

An analytical study of the mutual interaction between a wake vortex and an encountering airplane has been conducted. The interaction was calculated on the basis of conservation of angular momentum of the wake vortex and the encountering airplane in the roll axis. For the nominal conditions assumed in the study, the interaction reduced the roll response in the lust second by 20 percent compared to the classical method of calculating the response. However, depending on the conditions assumed, the reduction varied from 0 to 30 percent which could be highly significant in determining separation standards for airplanes. Controlled experiments are needed to determine the exact amount of interaction.

Stewart, E. C.↗

The challenges of simulating wake vortex encounters and assessing separation criteria

During landings and take-offs, the longitudinal spacing between airplanes is in part determined by the safe separation required to avoid the trailing vortex wake of the preceding aircraft. Safe exploration of the feasibility of reducing longitudinal separation standards will require use of aircraft simulators. This paper discusses the approaches to vortex modeling, methods for modeling the aircraft/vortex interaction, some of the previous attempts of defining vortex hazard criteria, and current understanding of the development of vortex hazard criteria.

Dunham, R. E.↗

Wake Vortex Field Measurement Program at Memphis, Tennessee: Data Guide

Eliminating or reducing current restrictions in the air traffic control system due to wake vortex considerations would yield increased capacity, decreased delays, and cost savings. Current wake vortex separation standards are widely viewed as very conservative under most conditions. However, scientific uncertainty about wake vortex behavior under different atmospheric conditions remains a barrier to development of an adaptive vortex spacing system. The objective of the wake vortex field measurement efforts during December, 1994 and August, 1995 at Memphis, TN were to record wake vortex behavior for varying atmospheric conditions and types of aircraft. This effort is part of a larger effort by the NASA Langley Research Center to develop an Aircraft Vortex Spacing System (AVOSS) as an element of the Terminal Area Productivity (TAP) program. The TAP program is being performed in concert with the FAA Terminal Air Traffic Control Automation (TATCA) program and ATC Automation. Wake vortex behavior was observed using a mobile continuous-wave (CW) coherent laser Doppler radar (lidar) developed at Lincoln Laboratory. This lidar features a number of improvements over previous systems, including the first-ever demonstration of an automatic wake vortex detection and tracking algorithm.

Campbell, S. D.↗

Study of the Mutual Interaction Between a Wing Wake and an Encountering Airplane

In an effort to increase airport productivity, several wind-tunnel and flight-test programs are currently underway to determine safe reductions in separation standards between aircraft. These programs are designed to study numerous concepts from the characteristics and detection of wake vortices to the wake-vortex encounter phenomenon. As part of this latter effort, computational tools are being developed and utilized as a means of modeling and verifying wake-vortex hazard encounters. The objective of this study is to assess the ability of PMARC, a low-order potential-flow panel method, to predict the forces and moments imposed on a following business-jet configuration by a vortex interaction. Other issues addressed include the investigation of several wake models and their ability to predict wake shape and trajectory, the validity of the velocity field imposed on the following configuration, modeling techniques and the effect of the high-lift system and the empennage. Comparisons with wind-tunnel data reveal that PMARC predicts the characteristics for the clean wing-body following configuration fairly well. Non-linear effects produced by the addition of the high-lift system and empennage, however, are not so well predicted.

Walden, A. B.↗

Vortex Wake Turbulence: Flight Tests Conducted During 1970

A flight test program designed to obtain data on the characteristics of wing-tip vortices generated by large jet aircraft was initiated on 12 February 1970. The objective was to update the interim air traffic separation standards issued on 21 January 1970 restricting the airspace behind the B-747 and C-5A aircraft 60 deg either side and 2,000 feet below to a distance of 10 miles. The program involved flight tests at three different locations, which were conducted simultaneously. (1) At the Edwards Air Force Base test range, a NASA CV-990 and F-104 probed the vortices of a C-5A. This supplemented previous flight tests in U-3A and F-104 behind a B-52 and C-5A. (2) At Seattle, the Boeing Company probed the vortices of a B-747 and a B-707-300 with a B-737 and F-86. In addition, approach, landing, takeoff, and crossing runway tests were conducted with a B-737 trailing a B-747. Immediately following the Edwards tests, the NASA CV-990 proceeded to Seattle and engaged in probing flights behind the same B-747 and B-707-300. (3) At Idaho Falls, Idaho, FAA personnel, utilizing the Atomic Energy Commission and Environmental Science Services Administration facilities and a 200 ft, instrumented tower, conducted 114 flights past the tower. The aircraft were positioned to permit their vortices to descend into the air flow sensors and smoke generated from various levels on the tower. This permitted obtaining measurements and photography of the vortex core diameters, tangential velocities and related characteristics. Immediately following this test phase, analysis of the interrelated data was completed by the project managers representing NASA, Boeing and FAA and a Compilation of Work Papers was issued on 30 April 1970. These data were the basis of a revised General Notice issued on 26 February 1970 which, in essence, modified the restricted airspace to five miles behind heavy jets in the 300,000 lb. gross takeoff weight category.

Source record↗

Wake Vortex Advisory System (WakeVAS) Concept of Operations

NASA Langley Research Center has a long history of aircraft wake vortex research, with the most recent accomplishment of demonstrating the Aircraft VOrtex Spacing System (AVOSS) at Dallas/Forth Worth International Airport in July 2000. The AVOSS was a concept for an integration of technologies applied to providing dynamic wake-safe reduced spacing for single runway arrivals, as compared to current separation standards applied during instrument approaches. AVOSS included state-of-the-art weather sensors, wake sensors, and a wake behavior prediction algorithm. Using real-time data AVOSS averaged a 6% potential throughput increase over current standards. This report describes a Concept of Operations for applying the technologies demonstrated in the AVOSS to a variety of terminal operations to mitigate wake vortex capacity constraints. A discussion of the technological issues and open research questions that must be addressed to design a Wake Vortex Advisory System (WakeVAS) is included.

Rutishauser, David↗

Improved Conflict Detection for Reducing Operational Errors in Air Traffic Control

An operational error is an incident in which an air traffic controller allows the separation between two aircraft to fall below the minimum separation standard. The rates of such errors in the US have increased significantly over the past few years. This paper proposes new detection methods that can help correct this trend by improving on the performance of Conflict Alert, the existing software in the Host Computer System that is intended to detect and warn controllers of imminent conflicts. In addition to the usual trajectory based on the flight plan, a "dead-reckoning" trajectory (current velocity projection) is also generated for each aircraft and checked for conflicts. Filters for reducing common types of false alerts were implemented. The new detection methods were tested in three different ways. First, a simple flightpath command language was developed t o generate precisely controlled encounters for the purpose of testing the detection software. Second, written reports and tracking data were obtained for actual operational errors that occurred in the field, and these were "replayed" to test the new detection algorithms. Finally, the detection methods were used to shadow live traffic, and performance was analysed, particularly with regard to the false-alert rate. The results indicate that the new detection methods can provide timely warnings of imminent conflicts more consistently than Conflict Alert.

Paielli, Russell A.↗

Considerations in the Integration of Small Aircraft Transportation System Higher Volume Operations (SATSHVO) in the National Airspace System (NAS)

The Small Aircraft Transportation System Higher Volume Operations (SATS HVO) concept holds the promise for increased efficiency and throughput at many of the nations under-used airports. This concept allows for concurrent operations at uncontrolled airports that under today s procedures are restricted to one arrival or one departure operation at a time, when current-day IFR separation standards are applied. To allow for concurrent operations, SATS HVO proposes several fundamental changes to today's system. These changes include: creation of dedicated airspace, development of new procedures and communications (phraseologies), and assignment of roles and responsibilities for pilots and controllers, among others. These changes would affect operations on the airborne side (pilot) as well as the groundside (controller and air traffic flow process). The focus of this paper is to discuss some of the issues and potential problems that have been considered in the development of the SATS HVO concept, in particular from the ground side perspective. Reasonable solutions to the issues raised here have been proposed by the SATS HVO team, and are discussed in this paper.

Lohr, Gary W.↗

Analysis of WakeVAS Benefits Using ACES Build 3.2.1

The FAA and NASA are currently engaged in a Wake Turbulence Research Program to revise wake turbulence separation standards, procedures, and criteria to increase airport capacity while maintaining or increasing safety. The research program is divided into three phases: Phase I near term procedural enhancements; Phase II wind dependent Wake Vortex Advisory System (WakeVAS) Concepts of Operations (ConOps); and Phase III farther term ConOps based on wake prediction and sensing. This report contains an analysis that evaluates the benefits of a closely spaced parallel runway (CSPR) Phase I ConOps, a single runway and CSPR Phase II ConOps and a single runway Phase III ConOps. A series of simulation runs were performed using the Airspace Concepts Evaluation System (ACES) Build 3.21 air traffic simulator to provide an initial assessment of the reduction in delay and cost savings obtained by the use of a WakeVAS at selected U.S. airports. The ACES simulator is being developed by NASA Ames Research Center as part of the Virtual Airspace Modelling and Simulation (VAMS) program.

Smith, Jeremy C.↗

Analysis of Wake VAS Benefits Using ACES Build 3.2.1: VAMS Type 1 Assessment

The FAA and NASA are currently engaged in a Wake Turbulence Research Program to revise wake turbulence separation standards, procedures, and criteria to increase airport capacity while maintaining or increasing safety. The research program is divided into three phases: Phase I near term procedural enhancements; Phase II wind dependent Wake Vortex Advisory System (WakeVAS) Concepts of Operations (ConOps); and Phase III farther term ConOps based on wake prediction and sensing. The Phase III Wake VAS ConOps is one element of the Virtual Airspace Modelling and Simulation (VAMS) program blended concepts for enhancing the total system wide capacity of the National Airspace System (NAS). This report contains a VAMS Program Type 1 (stand-alone) assessment of the expected capacity benefits of Wake VAS at the 35 FAA Benchmark Airports and determines the consequent reduction in delay using the Airspace Concepts Evaluation System (ACES) Build 3.2.1 simulator.

Smith, Jeremy C.↗

Wake Turbulence Mitigation for Arrivals (WTMA)

The preliminary Wake Turbulence Mitigation for Arrivals (WTMA) concept of operations is described in this paper. The WTMA concept provides further detail to work initiated by the Wake Vortex Avoidance System Concept Evaluation Team and is an evolution of the Wake Turbulence Mitigation for Departure concept. Anticipated benefits about reducing wake turbulence separation standards in crosswind conditions, and candidate WTMA system considerations are discussed.

Williams, Daniel M.↗

Relative-Motion Sensors and Actuators for Two Optical Tables

Optoelectronic sensors and magnetic actuators have been developed as parts of a system for controlling the relative position and attitude of two massive optical tables that float on separate standard air suspensions that attenuate ground vibrations. In the specific application for which these sensors and actuators were developed, one of the optical tables holds an optical system that mimics distant stars, while the other optical table holds a test article that simulates a spaceborne stellar interferometer that would be used to observe the stars. The control system is designed to suppress relative motion of the tables or, on demand, to impose controlled relative motion between the tables. The control system includes a sensor system that detects relative motion of the tables in six independent degrees of freedom and a drive system that can apply force to the star-simulator table in the six degrees of freedom. The sensor system includes (1) a set of laser heterodyne gauges and (2) a set of four diode lasers on the star-simulator table, each aimed at one of four quadrant photodiodes at nominal corresponding positions on the test-article table. The heterodyne gauges are used to measure relative displacements along the x axis.

Gursel, Yekta↗