Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shock Wave Boundary Layer Interaction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Heat-transfer measurements and computations of swept-shock-wave boundary-layer interactions

An experimental and computational research program providing new knowledge of the heat transfer in swept-shock-wave/boundary-layer interactions is described. An equilibrium turbulent boundary layer on a flat plate is subjected to impingement by a swept planar shock wave generated by a sharp fin. Five different interactions with fin angles ranging from 10 to 20 deg at freestream Mach numbers of 3 and 4 produce a variety of interaction strengths ranging from weak to very strong. A foil heater generates a uniform heat flux over the flat plate surface, and miniature thin-film-resistance sensors are used to measure the local surface temperature. The heat convection equation is then solved for the heat transfer distribution within an interaction, yielding an uncertainty of about +/- 10%. These data are compared with numerical Navier-Stokes solutions that employ a k-epsilon turbulence model. A simple peak heat transfer correlation for fin interactions is suggested.

Lee, Y.↗
NASA NTRS1975

Control of shock wave-boundary layer interactions by bleed in supersonic mixed compression inlets

An experimental investigation was conducted to determine the effect of bleed on a shock wave-boundary layer interaction in an axisymmetric mixed-compression supersonic inlet. The inlet was designed for a free-stream Mach number of 2.50 with 60-percent supersonic internal area contraction. The experiment was conducted in the NASA Lewis Research Center 10-Foot Supersonic Wind Tunnel. The effects of bleed amount and bleed geometry on the boundary layer after a shock wave-boundary layer interaction were studied. The effect of bleed on the transformed form factor is such that the full realizable reduction is obtained by bleeding of a mass flow equal to about one-half of the incident boundary layer mass flow. More bleeding does not yield further reduction. Bleeding upstream or downstream of the shock-induced pressure rise is preferable to bleeding across the shock-induced pressure rise.

Fukuda, M. K.↗
NASA NTRS1976

Turbulence measurements in hypersonic shock-wave boundary-layer interaction flows

Turbulent intensity and Reynolds shear stress measurements are presented for two nonadiabatic hypersonic shock-wave boundary-layer interaction flows, one with and one without separation. These measurements were obtained using a new hot-wire probe specially designed for heated flows. Comparison of the separated and attached flows shows a significant increase above equilibrium values in the turbulent intensity and shear stress downstream of the interaction region for the attached case, while for the separated case, the turbulent fluxes remain close to equilibrium values. This effect results in substantial differences in turbulence lifetimes for the two flows. It is proposed that these differences are due to a coupling between the turbulent energy and separation bubble unsteadiness, a hypothesis supported by the statistical properties of the turbulent fluctuations.

Mikulla, V.↗
NASA NTRS1976

Turbulence measurements in hypersonic shock-wave boundary-layer interaction flows

Turbulent intensity and Reynolds shear stress measurements are presented for two nonadiabatic hypersonic shock-wave boundary-layer interaction flows, one with and one without separation. These measurements were obtained using a new hot-wire probe specially designed for heated flows. Comparison of the separated and attached flows shows a significant increase above equilibrium values in the turbulent intensity and shear stress downstream of the interaction region for the attached case, while for the separated case, the turbulent fluxes remain close to equilibrium values. This effect results in substantial differences in turbulence lifetime for the two flows. We propose that these differences are due to a coupling between the turbulent energy and separation bubble unsteadiness, a hypothesis supported by the statistical properties of the turbulent fluctuations.

Mikulla, V.↗
NASA NTRS1993

Aerodynamic heating in the vicinity of hypersonic, axisymmetric, shock-wave boundary-layer interactions

Aerodynamic heating rates are calculated from time-dependent temperature measurements in the vicinity of shock-wave boundary-layer interactions due to conical compression ramps on an axisymmetric body. The data were acquired at the Ohio State University Aeronautical and Astronautical Research Laboratory and at the Air Force Flight Dynamics Laboratory at Mach numbers of 6 and 10. The model is a cylindrical body with a 10 deg conical nose. Conical ramps with half-angles of 10, 20, 25, 30, and 35 deg serve as shock-wave generators. Flowfield surveys are made in the vicinity of the ramp vertices, separation points, and reattachment points. Experimental results quantify temperature response and the resulting heat transfer rates as a function of ramp angle, Reynolds number and freestream Mach number. The temperature responses within the flowfield appear to be steady-state for all angles and all Reynolds numbers, and hence, the heat transfer rates appear to be steady-state.

Flanagan, M. J., Jr.↗
NASA NTRS2006

Optimal Control of Shock Wave Turbulent Boundary Layer Interactions Using Micro-Array Actuation

The intent of this study on micro-array flow control is to demonstrate the viability and economy of Response Surface Methodology (RSM) to determine optimal designs of micro-array actuation for controlling the shock wave turbulent boundary layer interactions within supersonic inlets and compare these concepts to conventional bleed performance. The term micro-array refers to micro-actuator arrays which have heights of 25 to 40 percent of the undisturbed supersonic boundary layer thickness. This study covers optimal control of shock wave turbulent boundary layer interactions using standard micro-vane, tapered micro-vane, and standard micro-ramp arrays at a free stream Mach number of 2.0. The effectiveness of the three micro-array devices was tested using a shock pressure rise induced by the 10 shock generator, which was sufficiently strong as to separate the turbulent supersonic boundary layer. The overall design purpose of the micro-arrays was to alter the properties of the supersonic boundary layer by introducing a cascade of counter-rotating micro-vortices in the near wall region. In this manner, the impact of the shock wave boundary layer (SWBL) interaction on the main flow field was minimized without boundary bleed.

Anderson, Bernhard H.↗
NASA NTRS1975

Control of shock-wave boundary-layer interactions by bleed in supersonic mixed compression inlets

An experimental investigation has been conducted to determine the effect of bleed region geometry and bleed rate on shock wave-boundary layer interactions in an axisymmetric, mixed-compression inlet at a Mach number of 2.5. The full realizable reduction in transformed form factor is obtained by bleeding off about half the incident boundary layer mass flow. Bleeding upstream or downstream of the shock-induced pressure rise is preferable to bleeding across the shock-induced pressure rise. Slanted holes are more effective than normal holes. Two different bleed hole sizes were tested without detectable difference in performance.

Fukuda, M. K.↗
NASA NTRS1975

An experimental documentation of a hypersonic shock-wave turbulent boundary layer interaction flow: With and without separation

An experiment, thoroughly documenting the flow field resulting from the interaction of a shock wave with a nonadiabatic hypersonic turbulent boundary layer, is described. Detailed mean flow and surface data are presented for two shock strengths resulting in attached and separated flows, respectively. The surface measurements include continuous pressure, shear and heat-flux distributions upstream, in, and downstream of the interaction regions. At closely spaced intervals along the surface, boundary-layer profiles of static and pitot pressure and total temperature were obtained from which velocity, density and static temperature profiles were derived. The data are presented in both graphical and tabular form. These data are of sufficient detail to validate advanced computer codes and their associated turbulence models.

Kussoy, M. I.↗
NASA NTRS1994

Validation of the RPLUS3D Code for Supersonic Inlet Applications Involving Three-Dimensional Shock Wave-Boundary Layer Interactions

A three-dimensional computational fluid dynamics code, RPLUS3D, which was developed for the reactive propulsive flows of ramjets and scramjets, was validated for glancing shock wave-boundary layer interactions. Both laminar and turbulent flows were studied. A supersonic flow over a wedge mounted on a flat plate was numerically simulated. For the laminar case, the static pressure distribution, velocity vectors, and particle traces on the flat plate were obtained. For turbulent flow, both the Baldwin-Lomax and Chien two-equation turbulent models were used. The static pressure distributions, pitot pressure, and yaw angle profiles were computed. In addition, the velocity vectors and particle traces on the flat plate were also obtained from the computed solution. Overall, the computed results for both laminar and turbulent cases compared very well with the experimentally obtained data.

Kapoor, Kamlesh↗
NASA NTRS1982

Turbulence amplification in shock-wave boundary-layer interaction

Attention is directed to the acoustics research of the 1950s and 1960s for guidance in understanding and quantizing the turbulence amplification that can occur in regions of shock-wave boundary-layer interaction. Three primary turbulence amplifier-generator mechanisms are identified and shown, by linear analysis, to be responsible for turbulence amplification across a shock wave in excess of 100% of the incident turbulence intensity.

Anyiwo, J. C.↗
NASA NTRS1989

An LDA (Laser-Doppler Anemometry) investigation of three-dimensional normal shock wave boundary-layer interactions

Nonintrusive measurements were made of a normal shock wave/boundary layer interaction. Two dimensional measurements were made throughout the interaction region while 3-D measurements were made in the vicinity of the shock wave. The measurements were made in the corner of the test section of a continuous supersonic wind tunnel in which a normal shock wave had been stabilized. Laser Doppler Anemometry, surface pressure measurement and flow visualization techniques were employed for two freestream Mach number test cases: 1.6 and 1.3. The former contained separated flow regions and a system of shock waves. The latter was found to be far less complicated. The results define the flow field structure in detail for each case.

Chriss, R. M.↗
NASA NTRS1991

Crossing shock wave-turbulent boundary layer interactions

Three-dimensional interactions between crossing shock waves generated by symmetric sharp fins and a turbulent boundary layer on a flat plate are investigated experimentally and theoretically at Mach number 2.95 and freestream unit Reynolds number 1.96 x 10 to the 7th/ft. The incoming boundary layer has a thickness of 4 mm at the location of the fin leading edges. A comparison of experimental and computational results for two sets of fin angles (11 x 11 and 9 x 9 deg) shows general agreement with regard to surface pressure measurements and surface streamline patterns. The principal feature of the streamline structure is a collision of counterrotating vortical structures emanating from near the fin leading edges and meeting at the geometric centerline of the interaction.

Narayanswami, N.↗
NASA NTRS1980

Asymptotic features of shock-wave boundary-layer interaction

A semi-implicit method is applied to solve the Navier-Stokes equations numerically and to evaluate the features of the free-interaction phenomenon that occurs when a shock wave impinges on a Blasius boundary layer. Comparisons are made with predictions of the triple-deck theory and experiment. Results include pressure and skin-friction distribution in the free-interaction region for various values of Reynolds number.

Hussaini, M. Y.↗
NASA NTRS1995

Reduction of fluctuating pressure loads in shock wave turbulent boundary layer interactions

Fluctuating surface pressure measurements have been made to investigate the effectiveness of boundary layer separators (BLS's) in reducing the fluctuating pressure loads produced by separated shock wave turbulent boundary layer interactions. Measurements have been made under unswept and swept compression corner interactions in a Mach 5 flow. BLS's fix the separation location and eliminate the large-amplitude, low-frequency fluctuating pressure loads upstream of the compression corners. The loads on the unswept compression corner face are reduced by as much as 59%. The BLS's also shift the mean pressure distribution on the unswept corner face in the streamwise direction. Results show that the loads on the corner face vary with the BLS height and the distance between the BLS and the compression corner. Suggestions for the optimum placement and the use of the BLS's are also made.

Barter, John W.↗