Search NASA⌕ Search

SEARCH · Search NASA

Results for “Small Core”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

From MAST-U to STEP: Power exhaust control challenges and opportunities

This work explores the challenges and opportunities for power exhaust control in STEP, informed by dedicated MAST-U experiments. The STEP system primarily relies on hydrogenic and argon gas injection into the divertors, compensating for transients originating in the plasma core. Fast transients (>10 Hz) that evolve too quickly for actuators to compensate must be absorbed passively; the enhanced transient buffering of the foreseen long-legged divertor provides a clear advantage over conventional geometries, as demonstrated in the MAST-U Super-X divertor. Experiments further indicate that STEP’s tight divertor baffling enables near-independent control of the upper and lower divertors. The most challenging transients are expected from power-sharing fluctuations, as MAST-U experiments observed extremely fast dynamics. Fluctuations from core pellet fuelling remain relatively benign due to the small pellet size according to simulations. Exhaust control in a reactor like STEP requires an integrated approach befitting its machine-critical nature. A predictive control element, integrated with core plasma control, allows pre-emptive preparation of the divertor for incoming transients. An observer-based diagnostic approach is foreseen to monitor the divertor in the challenging reactor environment, supported by an extended diagnostic set in the non-nuclear phase to validate the required dynamic models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Time-resolved atomic-resolution Brownian tomography of single nanocrystals reveals size-dependent dynamics

Atomic-resolution structure identification of nanocrystals by graphene liquid cell electron microscopy (GLC-EM) has revealed that small, solubilized platinum nanocrystals consist of an ordered crystalline core surrounded by mobile surface atoms, which dissociate during oxidative etching, resulting in distinct temporal structural states. Requirements imposed by the 3D reconstruction algorithm limit the number of structural states that can be resolved. We introduce a regularized 3D reconstruction algorithm that exploits the redundancy inherent in the experimental data, allowing us to improve the time resolution. Our developments provide a comprehensive molecular picture at unprecedented spatial and temporal resolution of the nonlinear, linear, and fluctuating dynamic phenomena that single nanocrystals undergo during the GLC-EM experiment. We determined atomic structures of 66 temporal structural states, extracted from 15 time trajectories of individual nanocrystals. Large (478 to 698 atoms) and small (<300 atoms) nanocrystals show etching that preserves a stable core, whereas mid-sized (351 to 571 atoms) nanocrystals present dynamics that change the coordination of the core.

Meana-Pañeda, Rubén↗
DOE OSTI2025

Multiscale Modeling Framework Using Element‐Based Galerkin Methods for Moist Atmospheric Limited‐Area Simulations

This paper presents a multiscale modeling framework (MMF) to model moist atmospheric limited-area weather. The MMF resolves large-scale convection using a coarse grid while simultaneously resolving local features through numerous fine local grids and coupling them seamlessly. Both large- and small-scale processes are modeled using the compressible Navier-Stokes equations within the Nonhydrostatic Unified Model of the Atmosphere (NUMA), and are discretized using a continuous element-based Galerkin method (spectral elements) with high-order basis functions. Consequently, the large-scale and small-scale models share the same dynamical core but have the flexibility to be adjusted individually. The proposed MMF method is tested in 2D and 3D idealized limited-area weather problems involving storm clouds produced by squall line and supercell simulations. Numerical results from the MMF showed enhanced representation of cloud processes compared to the coarse model.

Kang, Soonpil [Naval Postgraduate School, Monterey↗
DOE OSTI2025

Impact of moisture on microbial decomposition phenotypes and enzyme dynamics

Soil organic matter decomposition is a complex process reflecting microbial composition and environmental conditions. Moisture can modulate the connectivity and interactions of microbes. Due to heterogeneity, a deeper understanding of the influence of soil moisture on the dynamics of organic matter decomposition and resultant phenotypes remains a challenge. Soils from a long-term field experiment exposed to high and low moisture treatments were incubated in the laboratory to investigate organic matter decomposition using chitin as a model substrate. By combining enzymatic assays, biomass measurements, and microbial enrichment via activity-based probes, we determined the microbial functional response to chitin amendments and field moisture treatments at both the community and cell scales. Chitinolytic activities showed significant responses to the amendment of chitin, independent of differences in field moisture treatments. However, for other measurements of carbon metabolism and cellular functions, soils from high moisture field treatments had greater potential enzyme activity than soils from low moisture field treatments. A cell tagging approach was used to enrich and quantify bacterial taxa that are actively producing chitin-degrading enzymes. By integrating organism, community, and soil core measurements we show that (i) a small subset of taxa compose the majority (>50%) of chitinase production despite broad functional redundancy, (ii) the identity of key chitin degraders varies with moisture level, and (iii) extracellular enzymes that are not cell-associated account for most potential chitinase activity measured in field soil.

activity-based probes↗
DOE OSTI2025

pseudopod

Pseudopod is a software tool that makes it easier and safer to build and run Linux containers without needing additional system privileges. It is designed to work with the open-soruce Podman container runtime. Pseudopod also provides and implements small library named libpseudo that provides the core functionality for tracking and emulating identity related system calls with low performance overhead. This allows complex tools, such as package managers and build systems, to run in a familiar way within a container while preserving the security of the host system and networks.

Green, ElenaN [Lawrence Livermore National Laborat↗
DOE OSTI2025

DE‐SC0022708 RESEARCH PERFORMANCE FINAL REPORT

GismoPower’s Final Research Report documents the outcomes of a DOE SBIR Phase II project focused on advancing the MEGA® (Mobile Electricity Generating Appliance), a trailerable, plug-in solar canopy appliance designed to deliver appliance-class electricity generation for homes, small businesses and renters. The project’s core objective was to remove the technical and regulatory barriers that have historically prevented plug-in solar systems from being safely certified, permitted, and interconnected in the United States.

14 SOLAR ENERGY↗
DOE OSTI2024

Waveguides for neurostimulation in the cochlea

Introduction Optical stimulation has been suggested for neural stimulation to improve cochlear implants. Light allows for more spatially selective activation of neuron populations than electrical current, offering more independent frequency bands along the spiral ganglion. These bands are available to encode acoustic information with anticipated better frequency resolution, improving cochlear implant user performance in noisy listening environments, tonal languages, and music perception. Methods Optical cochlear implants (oCIs) can deliver light either directly via small emitters within the cochlea or via waveguides from external optical sources. We investigated three waveguide designs made from OrmoComp ® , a polymer that cures through ultraviolet (UV) radiation. Waveguides were fabricated via injection molding and coated using dip-coating or thermal reflow, or through aspiration of OrmoComp ® into polyimide tubing that served as the cladding of the waveguide. The choice of fabrication technique directly determined the waveguides' total diameter: thermal reflow yielded ≈940 μm, dip-coating produced ≈306 μm, and aspiration resulted in ≈132 μm core diameter waveguides. Given the human cochlea's small size, we focused on analyzing the 306-μm and 132-μm waveguides, evaluating their optical performance (propagation and bending losses) and mechanical properties (bending stiffness and insertion forces). Furthermore, we evaluated some of these designs in in-vivo guinea pigs experiments. Results For the 100-μm core diameter waveguides, the propagation losses were 12.34 ± 1.26, 1.18 ± 0.88, 1.49 ± 0.58, and 3.43 ± 0.68 dB/cm at 534, 1,375, 1,460, and 1,550 nm, respectively. The respective bending losses at a 2 mm radius of curvature were 5.50 ± 1.32, 0.56 ± 0.26, 0.79 ± 0.18, and 0.64 ± 0.23 dB, and at 1 mm 8.54 ± 1.30, 2.05 ± 0.84, 2.11 ± 0.50, and 1.44 ± 0.37 dB. The bending stiffness of a 1 mm segment of the 100-μm-diameter waveguides was 18.9 ± 2.2 N/m. Insertion forces for the 100-μm-diameter waveguides into an acrylic human-size scala tympani model were < 25 mN. For the waveguides with 306 and 940 μm total diameter, the propagation losses ranged between 0.43 and 2.40 dB/cm at 534, 680, 1,375, and 1,550 nm, between 2.19 and 3.78 dB/cm at 450 and 1,460 nm. Bending losses for 360 degrees at 1,375 nm were 5.0, 2.4, and 0.46 for a bending radius of 2.5-, 3-, and 4-mm. Discussion Our study demonstrated that the polymer OrmoComp ® is suitable for fabricating waveguides to transmit near-infrared radiation. In-vivo experiments showed optically evoked auditory responses originating from optical stimulation in the guinea pigs' first cochlear turn while radiation was delivered. Incoming experiments will focus on evaluating long-term performance of these waveguides in guinea pigs and cats. This study will be designed to provide insights into the waveguides' performance and biocompatibility over extended periods, essential for their potential clinical application in future oCIs.

Kim, Matthew↗
DOE OSTI2026

Geology of the One Earth Energy Site

The One Earth Energy site is one of two sites in the Illinois Storage Corridor (ISC) project. The objectives of the ISC project is to accelerate commercial deployment of carbon capture utilization and storage at two individual sites and receive approvals for Underground Injection Control (UIC) Class VI permits for construction at each site. At the One Earth Energy site, an extensive data collection program was undertaken, which included the drilling of a test well (One Earth Energy #1 [OEE #1]), four 2D seismic lines, and a small 3D seismic survey. The OEE #1 well was drilled in 2022 and acquired extensive core, log, and testing data to characterize the subsurface geology of the site. Coring was focused on the storage interval, the Mt. Simon Sandstone, and the confining interval, the Eau Claire Formation. The core and log data were used to evaluate the sedimentology and sequence stratigraphy, as well as to develop the conceptual geologic model. This report includes the geological summaries of the Mt. Simon Sandstone and the Eau Claire Formation. The extensive analysis of the log data is included in the petrophysical section, showing ranges of porosity, estimated pore size, and the mineral content of selected zones in the well. The separate petrographic technical report entitled “Petrographic and Advanced Geologic Characterization Report on One Earth Energy #1 (API# 1211325373)”, report number DOE-UIUC-0031892-04, details thin section point-counting analysis that includes mineralogical and pore space analysis, including grain size analysis, annotated thin section photomicrographs, scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), and statistics of grain size analysis on Mt. Simon thin sections from OEE #1. The final OEE #1 well data to be included in this geology report is the routine core analysis of both whole core plugs and rotary sidewall core plugs. In addition to the OEE #1 well, four 2D seismic lines and a small 3D survey were acquired as part of the overall subsurface geological characterization. This geology report references the seismic interpretation report, entitled “One Earth Energy Site Seismic Interpretation Task 5.0”, report number DOE-UIUC-0031892-07. This report details the stratigraphic and structural interpretation of the 2D and 3D seismic data acquired at the One Earth Energy site. The 2D seismic data was acquired in 2019 and 2021, and the 3D survey was acquired in 2022. The objectives of the seismic programs were to contribute to the subsurface characterization of the Mt. Simon-Eau Claire Storage Complex by evaluating the continuity of potential storage reservoirs and containment intervals across the project area, and to determine if any geologic features are present that would increase containment risk to the proposed carbon storage project.

09 BIOMASS FUELS↗
DOE OSTI2025

FAST Irradiations, Postirradiation Examinations, and Modeling of U-Mo for Light Water Reactor Applications

Many next generation light water reactor (LWR) concepts, such as mobile small modular reactors, are seeking to use smaller core dimensions than conventional reactor types. Smaller reactor cores require an increase in fissile material to maintain reactivity. For non-proliferation purposes, enrichment increases are limited to less than 20% (high assay low enriched uranium, [HALEU]) and so higher uranium density fuels than UO 2 must be considered. To this end, uranium-molybdenum alloys were tested using the Fission Accelerated Steady-state Test (FAST) approach. The experiment test matrix is focused on identifying the temperature transition between low swelling and high fission gas retention to break away swelling and low fission gas retention. This paper documents the results of irradiation tests and post-irradiation examinations (PIE) including neutron radiography, rodlet profilometry, fission gas collection analysis, and optical metallography. The results of these tests showed that unconstrained U-Mo fuels (solid, Na-bonded rodlets) have a swelling threshold between 400-450°C with minimal fission gas release below this point. Higher temperature solid fuel showed microstructural zoning with small pore networks while lower temperature solid fuels have a uniform microstructure with large pore networks. U-Annular Mo fuels where swelling had some self-constraint imposed upon it, were shown to have much reduced swelling compared to their solid counterparts as well as very low fission gas release for irradiation temperatures up to 500°C. These initial results show that the use of U-Mo in constrained fuel geometries could be used as a high uranium density HALEU fuel for LWRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Attosecond Probing of Coherent Vibrational Dynamics in CBr 4

A coherent vibrational wavepacket is launched and manipulated in the symmetric stretch (a1) mode of CBr 4 , by impulsive stimulated Raman scattering (ISRS) from nonresonant 400 nm laser pump pulses with various peak intensities on the order of tens of 10 12 W/cm 2 . Extreme ultraviolet (XUV) attosecond transient absorption spectroscopy (ATAS) records the wavepacket dynamics as temporal oscillations in XUV absorption energy at the bromine M 4,5 3d 3/2,5/2 edges around 70 eV. The results are augmented by nuclear timedependent Schrödinger equation simulations. Slopes of the (Br 3d 3/2,5/2 ) –1 10a 1 * core-excited state potential energy surface (PES) along the a 1 mode are calculated to be –9.4 eV/Å from restricted open-shell Kohn–Sham calculations. Using analytical relations derived for the small-displacement limit and the calculated slopes of the core-excited state PES, a deeper insight into the vibrational dynamics is obtained by retrieving the experimental excursion amplitude of the vibrational wavepacket and the amount of population transferred to the vibrational first-excited state as a function of pump-pulse peak intensity. Experimentally, the results show that XUV ATAS is capable of resolving oscillations in the XUV absorption energy on the order of a few to tens of meV with tens of femtosecond time precision. This corresponds to change in C–Br bond length on the order of 10 –4 to 10 –3 Å. The results and the analytic relationships offer a clear physical picture, on multiple levels of understanding, of how the pump-pulse peak intensity controls the vibrational dynamics launched by nonresonant ISRS in the small-displacement limit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Long-Chain Lipids Facilitate Insertion of Large Nanoparticles into Membranes of Small Unilamellar Vesicles

Insertion of hydrophobic nanoparticles into phospholipid bilayers is limited to small particles that can incorporate into a hydrophobic membrane core between two lipid leaflets. Incorporation of nanoparticles above this size limit requires the development of challenging surface engineering methodologies. In principle, increasing the long-chain lipid component in the lipid mixture should facilitate incorporation of larger nanoparticles. Here, we explore the effect of incorporating very long phospholipids (C24:1) into small unilamellar vesicles on the membrane insertion efficiency of hydrophobic nanoparticles that are 5–11 nm in diameter. To this end, we improve an existing vesicle preparation protocol and utilized cryogenic electron microscopy imaging to examine the mode of interaction and evaluate the insertion efficiency of membrane-inserted nanoparticles. We also perform classical coarse-grained molecular dynamics simulations to identify changes in lipid membrane structural properties that may increase insertion efficiency. Furthermore, our results indicate that long-chain lipids increase the insertion efficiency by preferentially accumulating near membrane-inserted nanoparticles to reduce the thermodynamically unfavorable disruption of the membrane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Bridging the Gap Between LLMs and LNS with Dynamic Data Format and Architecture Codesign

Deep neural networks (DNNs) have achieved tremendous success in the past few years. However, their training and inference demand exceptional computational and memory resources. Quantization has been shown as an effective approach to mitigate the cost, with the mainstream data types reduced from FP32 to FP16/BF16 and recently FP8 in the latest NVIDIA H100 GPUs. With increasingly aggressive quantization, however, the conventional floating-point formats suffer from limited precision in representing numbers around zero. Recently, NVIDIA demonstrated the potential of using a Logarithmic Number System (LNS) for the next generation of tensor cores. While LNS mitigates the hurdles in representing small numbers, in this work we observed a mismatch between LNS and the emerging Large Language Models (LLM), where LLM exhibits significant outliers when directly adopting the LNS format. In this paper, we present a data-format/architecture codesign to bright this gap. On the format side, we propose a dynamic LNS format to flexibly represent outliers at a higher precision, by exploiting asymmetry in the LNS representation and identifying outliers through a per-vector basis. On the architecture side, for demonstration, we realize the dynamic LNS format in a systolic array, which can handle the irregularity of the outliers at runtime. We implement our approach on an Alveo U280 FPGA as a prototype. Experimental results show that our design can effectively handle the outliers and resolve the mismatch between LNS and LLM, contributing to an accuracy improvement of 15.4% and 16% over the floating-point and the original LNS baselines, using four state-of-the-art LLM models. Our observation and design lay a solid foundation for the large-scale adoption of the LNS format in the next-generation deep learning hardware.

Haghi, Pouya↗
DOE OSTI2024

Impact of Linker Engineering in Core‐Linked Dimeric Acceptors for High‐Performance Organic Solar Cells

Abstract The dimerization of small molecule acceptors (SMAs) is a promising strategy for enhancing the long‐term stability and power conversion efficiency (PCE) of organic solar cells (OSCs). However, the reported DSMAs are primarily limited to end‐linked molecular configurations, highlighting the need for further exploration of various dimer architectures. Herein, the development of two distinct core‐linked dimerized SMAs (DYF‐V and DYF‐E) are reported with tailored linker structures (vinylene and ethynyl, respectively), achieving high‐performance OSCs (PCE = 18.53%). Interestingly, a subtle change in the linker structures results in markedly different molecular properties and photovoltaic performances of the dimer acceptors. DYF‐E with an ethynyl linker exhibits more twisted backbone conformation and mitigated aggregation property compared to DYF‐V, inducing desirable blend morphologies with a polymer donor including high crystallinity, face‐on oriented packing structures, and well‐intermixed domains. Thus, the DYF‐E‐based OSCs exhibit a high PCE (17.02%), which significantly outperforms the DYF‐V‐based OSCs (PCE = 9.98%). Furthermore, the ternary OSCs based on DYF‐E achieve a higher PCE of 18.53%. Thus, this study highlights the significance of selecting an appropriate linker in core‐linked dimerized SMAs for producing high‐performance OSCs.

Oh, Shinbee↗
DOE OSTI2025

Soft Nanoconfinement Nucleates and Stabilizes Ultrasmall Amorphous Calcium Carbonate from Aggregation

Organisms use soft confinement structures, such as vesicles and compartments, to direct the nucleation of calcium carbonate (CaCO 3 ) and its subsequent processes during biomineralization. Despite recent efforts elucidating confinement’s effects on CaCO 3 polymorph selection, we still poorly understand how the size and distribution of CaCO 3 are controlled within soft confinement. Here, using a size-controlled nanoemulsions system made from isooctane, Span 80, Tween 80, and aqueous solutions, we studied CaCO 3 formation in soft confinement. Small angle X-ray scattering (SAXS) confirmed that a 72 nm aqueous core in nanoemulsions served as the confined space for CaCO 3 formation. Unlike the ~ 50 nm CaCO 3 particles that formed in the unconfined solution, small angle neutron scattering (SANS) and transmission electron microscope (TEM) showed that ultrasmall and amorphous calcium carbonate precipitated within soft confinement and did not exhibit any aggregation/coalescence of nanoparticles even after 24 hrs of reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Characterization of the ELM-free negative triangularity edge on DIII-D

Tokamak plasmas with strong negative triangularity (NT) shaping typically exhibit fundamentally different edge behavior than conventional L-mode or H-mode plasmas. On DIII-D, every plasma with sufficiently negative triangularity (δ < δ crit ≃ -0.12) is found to be inherently free of edge localized modes (ELMs), even at injected powers well above the predicted L-H power threshold. It is also possible to access an ELM free state at weaker average triangularities provided that at least one of the two x-points is still sufficiently negative. Access to the ELM-free NT scenario is found to coincide with the closure of the second stability region for infinite-n ballooning modes, suggesting that ballooning stability may play a role in limiting the accessible pressure gradient in NT plasmas. Despite this, NT plasmas are able to support small pedestals and are typically characterized by an enhancement of edge pressure gradients beyond those found in traditional L mode plasmas. Further, the pressure gradient inside of this small pedestal is unusually steep, allowing access to high core performance that is competitive with other ELM-free regimes previously achieved on DIII-D. Since ELM-free operation in NT is linked directly to the magnetic geometry, NT fusion pilot plants are predicted to maintain advantageous edge conditions even in burning plasma regimes, potentially eliminating reactor core-integration issues caused by ELMs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Structural and physicochemical insights into pH-responsive poly(DEAEMA- co -HEMA)-grafted mesoporous silica nanoparticles

Mesoporous silica nanoparticles (SiO 2 ) grafted with responsive polymer shells are versatile hybrid systems. Understanding their three-dimensional organization in the hydrated state remains a significant challenge. Here, in this study, SiO 2 nanoparticles were functionalized with a poly(DEAEMA-co-HEMA) shell via a “grafting-from” polymerization strategy in aqueous media. Successful surface modification was confirmed by FTIR, thermogravimetric analysis, transmission electron microscopy, X-ray photoelectron spectroscopy, N 2 sorption, and ζ-potential, yielding grafting contents of 22% (p1 DEAEMA-co-HEMA ) and 49% (p2 DEAEMA-co-HEMA ). Small-angle neutron scattering (SANS) with solvent contrast variation was employed to elucidate the solution-state core–shell architecture of p1 and p2 hybrids at pH 2, where the grafted polymer shell is protonated and highly hydrated. Near contrast matching of the silica core, theoretically estimated at 58% D 2 O, suppressed the scattering intensity, enhancing sensitivity to the polymer shell. Constrained core–shell ellipsoid modeling across solvent contrasts revealed a systematic increase in shell thickness, overall particle dimensions, and shell anisotropy with increasing grafting content. In solution, the hydrated polymer shells were markedly more extended and structurally anisotropic than suggested by dry-state techniques structural characterization, highlighting the importance of solution-state structural analysis for accurately describing grafted polymer architectures.

Core-shell biomaterials↗
DOE OSTI2024

Material Characterization Study of Magnetite Nanocrystals for RF Sensing

Magnetite nanocrystals show promise for electrically small gigahertz frequency applications, which could lead to miniaturizing transformer cores and new sensing technologies. This work presents a rigorous radiofrequency characterization of these nanocrystals using vector network analyzer (VNA) ferromagnetic resonance (FMR) measurements. For the first time, two different average diameters of Fe 3 O 4 nanocrystals are investigated (7.3 and 20.2 nm). When the VNA–FMR results were compared to micromagnetic simulations, the magnetic anisotropy (K 1 ) deviated from the ideal mean orientation value of K 1 /2 to K 1 /80 for the 7.3 nm nanocrystal. In contrast, the obtained magnetic anisotropy in 20.2 nm nanocrystals slightly deviated to K 1 /11 due to less structural deformations. These findings resulted in a newly proposed methodology for an approximate simulation based on VNA–FMR measurements. In addition, this work estimates the approximate amount of nanocrystals needed to measure a useful VNA–FMR spectrum.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Assembly Bowing Reactivity Calculation Methodology Applied to Lead Fast Reactor

Ducted assemblies bow during operation due to power and temperature gradients which can be influenced by operating flow rates. For fast spectrum cores using ducted assemblies, the bowing behavior follows that of the duct and because there are gaps between the ducts, the bowing can result in compaction or expansion of the active core. This local displacement can have a positive or negative impact and knowing the net effect during transients is important for system reactivity control. Keeping the net bowing reactivity worth low is possible with attentive placement of load pads above the active core and selecting load pad gap thicknesses that result in a desired behavior at standard operating conditions. This paper considers a Lead Fast Reactor (LFR) concept fueled by HALEU UO2 developed by Westinghouse Electric Company (WEC) and applies a workflow of Argonne-developed codes to estimate the core bowing reactivity worth. Using orifice flow rates grouped by assembly type, the net reactivity impact due to core assembly bowing for the LFR was found to be small and in line with other liquid metal fast reactors: +29/+32/+35 pcm, or about +$0.049/+$0.055/+$0.059, for BOEC/MOEC/EOEC, respectively.

bowing reactivity↗