Search NASA⌕ Search

SEARCH · Search NASA

Results for “Small-Scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Stability and Control Characteristics of a Small-Scale Model of an Aerial Vehicle Supported by Two Ducted Fans

An investigation has been made to determine the stability and control characteristics in hovering and in forward flight of a free-flight model representing a type of vertical-take-off-and-landing aircraft which utilizes two fixed ducted fans as its sole source of lift and propulsion. The model, having fans 28 inches in diameter, was considered to be approximately one-third the size of a full-scale aircraft. Control moments for most of the hovering tests and all the forward-flight tests were provided by remotely controlled compressed-air jets at the sides and ends of the model. For one brief phase of the hovering investigation a system of vanes in the duct slipstreams was substituted for the jets as a means of roll control. During the forward-flight tests, the model was flown with both the tandem and side-by-side duct arrangements. In hovering the model exhibited strongly divergent oscillations about the pitch and roll axes. The pitching oscillation of the tandem configuration was of a fairly long period and was not particularly difficult to control; the rolling oscillation, however, was of a relatively short period and was extremely difficult to control. Both oscillations could be completely eliminated by the addition of a sufficient amount of artificial damping. The control moments produced by the vane-type roll control system were weak and were accompanied by a side force of appreciable magnitude and undesirable direction. In forward flight the model required an undesirably large nose-down tilt angle for equilibrium at any appreciable speed. A vane was placed transversely in the slipstream of the forward duct of the tandem configuration in an attempt to reduce this tilt angle. The vane was effective in reducing the tilt angle but apparently caused an increase in the power requirements and in the angle-of-attack instability. Without the vane, a forward speed of 30 knots (full scale) required a nose-down tilt angle of about 300. A powerful pitch control moment was required not only to maintain the trim attitude but also to 2 overcome the effects of instability with angle of attack. Less pitch control moment was required for the tandem configuration than for the side-by-side configuration at any given forward speed. The instability in roll increased with forward speed. No forward speeds in excess of about 20 knots (full scale) were achieved until the artificial damping in roll and the yaw control moment were increased appreciably above values which had proved satisfactory for hovering flight.

Parlett, Lysle P.↗
NASA NTRS1960

Wind-Tunnel Investigation of a Small-Scale Model of an Aerial Vehicle Supported by Tilting Ducted Fans

A wind-tunnel investigation has been made to study the static longitudinal and lateral stability characteristics of a simplified aerial vehicle supported by ducted fans that tilt relative to the airframe. The ducts were in a triangular arrangement with one duct in front and two at the rear in order to minimize the influence of the downwash of the front duct on the rear ducts. The results of the investigation were compared with those of a similar investigation for a tandem two-duct arrangement in which the ducts were fixed (rather than tiltable) relative to the airframe, since the three-duct configuration had been devised in an attempt to avoid some of the deficiencies of the tandem fixed-duct configuration. The results of the investigation indicated that the tilting-duct arrangement had less noseup pitching moment for a given forward speed than the tandem fixed-duct arrangement. The model had less angle-of-attack instability than the tandem fixed-duct arrangement. The model was directionally unstable but had a positive dihedral effect throughout the test speed range.

Smith, Charles C., Jr.↗
NASA NTRS1947

An Investigation of the Low-speed Stability and Control Characteristics of Swept-forward and Swept-back Wing in the Ames 40- by 80-foot Wind Tunnel

An investigation has been made at large scale of the characteristics of highly swept wings. Data were obtained at several angles of sideslip on wings having angles of sweep of plus or minus 45 degrees, plus or minus 30 degrees, and 0 degrees. The airfoil sections of the wings varied from approximately NACA 0015 at the root to NACA 23009 at the tip. Each wing was investigated with flaps under flection, partial-span split flaps deflected 60 degrees, full-span split flaps defected 60 degrees and split-flap-type ailerons deflected plus or minus 15 degrees. Values of maximum lift were obtained at Reynolds numbers raging from 5.7 to 9.2 times 10 to the 6th power. In this report the summarized results are compared with the predictions made by use of the simplified theory for the effect of sweep and with existing small-scale data. The basic wind-tunnel results from which these summary data were taken are included in an appendix. The primary problems accompanying the use of weep as revealed by this investigation are the loss in maximum lift, the high effective dihedral, and the sharp reduction in lateral-control effectiveness. In general, simple theory enables good predictions to be made of the gross effects of sweep but further refinements are necessary to obtain the accuracy required for design purposes. In cases where comparisons can be made, the indications are that, as sweep increases, scale effects diminish and large-scale results approach small-scale results.

Mccormack, Gerald M↗
NASA NTRS1966

A Supersonic/Hypersonic Aerodynamic Investigation of the Saturn 1B/Apollo Upper Stage

The static stability and axial force characteristics of an upper stage Saturn 1B/Apollo model were investigated in a series of wind tunnel tests at Mach numbers between 1. 93 and 8. 05. This report presents and analyzes the results of these small-scale studies. Test procedures and models are described, and consideration of boundary layer characteristics and violated modeling rules yields an assessment of the validity of the data. Four basic models provided evaluation of the basic launch vehicle characteristics, as well as the effects of two modes of mission abort and jettison of the launch escape system. The launch configuration experienced sudden, strong changes in stability derivatives and axial force coefficients near Mach 5. No similar changes were observed on the other configurations. Effects of Reynolds number, Mach number and boundary layer trips were obtained for each shape. The faired curves are believed to be valid for full-scale flight of the Saturn 1B/Apollo upper stage.

Source record↗
NASA NTRS1966

Comparison of wind-tunnel and flight results on a four-propeller tilt-wing configuration

Over the years aerodynamicists have learned to rely heavily on wind­-tunnel-model results in predicting the aerodynamic characteristics of con­ventional aircraft configurations. With the development of V/STOL con­figurations which have high slipstream deflection angles. such as the four-propeller tilt-wing XC-142A V/STOL aircraft, the reliability of small-scale wind-tunnel-model results in predicting full-scale airplane characteristics needs to be reexamined. Extensive tests have been made by NASA on several sizes of wind-tunnel models of the XC-142A V/STOL configuration and by Ling-Temco-Vought, Inc., on the airplane. These results show that models predict the slow-speed level-flight characteristics very well but that small models underpredict the descent capability of the airplane. Larger scale wind-tunnel models of approximately half size show better agreement with the airplane descent characteristics. It was found from smoke flow studies that small models can also pre­dict the region in which self-generated disturbances will be encountered by tilt-wing configurations in ground proximity.

WIND TUNNEL MODEL↗
NASA NTRS1960

Effects of Fixing Boundary-Layer Transition for a Swept- and a Triangular-Wing and Body Combination at Mach Numbers from 0.60 to 1.40

The aerodynamic effects of fixing boundary-layer transition for a swept- and a triangular-wing configuration have been determined from tests of two small-scale wing-body models. The wings had an aspect ratio of 2.99 and 3-percent-thick biconvex sections. Lift, pitching-moment, and drag data were obtained at Mach numbers ranging from 0.60 to 1.40 for angles of attack between -2 deg and about 15 deg. The Reynolds number of the tests was generally 1.5 million; however, minimum drag measurements were made for both models over a range of Reynolds numbers from 1.0 million to about 3.0 or 4.0 million.

Stivers, Louis S., Jr.↗
NASA NTRS1951

Wind-tunnel Tests at Low Speed of Swept and Yawed Wings Having Various Plan Forms

Results are presented of wind-tunnel tests made at low speed of various small-scale models of sweptback, sweptforward, and yawed wings. The tests covered changes in aspect ratio, taper ratio, and tip shape. Some data were obtained with high-lift devices on sweptback wings and with ailerons on sweptforward wings. The data have been briefly analyzed and some comparisons have been made with the available theory.

HIGH LIFT DEVICES - COMPLETE WINGS↗
NASA NTRS1953

Ignition Delays of Alkyl Thiophosphites with White and Red Fuming Nitric Acids Within Temperature Range 80 to -105 F

Ignition delays of alkyl thiophosphites were obtained in a modified open-cup apparatus and a small-scale rocket engine apparatus. At -40 F, mixed alkyl thiophosphites gave short delays with white fuming nitric acid containing 2 percent water and red fuming nitric acids of widely varying compositions. At -40 F and higher, triethyl trithiophosphite blended with as much as 40 percent n-heptane gave satisfactory self-igniting properties at temperatures as low as -76 F.

FUELS - PROPERTIES PHYSICAL AND CHEMICAL↗
NASA NTRS1944

Scale and Turbulence Effects on the Lift and Drag Characteristics of the NACA 65(Sub 3)-418, A=1.0 Airfoil Section

Wind-tunnel tests, investigating low drag wing performance in small-scale tests, showed a large increase in minimum drag coefficient, and a decrease of maximum lift coefficient occurred with decreasing Reynolds Number above certain designated values. The lift-curve slope varied up to 6% between high and low turbulence levels. Low Reynolds Number test data are unreliable for low drag airfoils either to estimate full-scale characteristics or to determine merits of airfoils for higher Reynolds numbers.

REYNOLDS NUMBER↗
NASA NTRS1946

The Knock-Limited Performance of Fuel Blends Containing Aromatics V : N-Propylbenzene, N-Butylbenzene, Isobutylbenzene, M-Xylene, and 1-Isopropyl-4-Methylbenzene

Results are reported of knock-limited tests of five aromatics, each individually blended with selected base fuels and tested with and without TEL, using 17.6, F-4, and F-3 small-scale engines. The five aromatics rated in the following order of decreasing antiknock effectiveness at fuel/air ratio 0.10: m-xylene, 1-isopropyl-4-methylbenzene, n-propylbenzene, isobutylbenzene, and n-butylbenzene.

FUELS - ISOPROPYLMETHYLBENZENE↗
NASA NTRS1955

Effect of surface roughness on characteristics of spherical shock waves

An investigation has been conducted on a small-scale test layout in which direct observation of the shock wave movement with time could be made in order to determine the effects of surface roughness on the characteristics of spherical shock waves. Data were obtained with 15-gram pentolite charges at four heights of burst, both for a smooth surface and for a surface completely covered with pyramid-shaped roughness elements. The observations resulted in determinations of shock peak overpressure and Mach stem height as a function of distance for each test. Comparison of the smooth-surface data with those obtained for the extremely rough condition showed a small net effort of roughness on the shock peak overpressures at the surface for all burst heights, the effect being to lower the overpressures. The effect of surface roughness on the Mach stem formation and growth was to delay the formation at the greatest charge height and to lower the height of the Mach stem for all heights.Comparison of the free-air shock peak overpressures with larger scale data showed good similarity of the overpressure-distance relationships. The data did not fit a geometrical similarity parameter for the path of the triple point at different heights of burst suggested by other investigators. A simple similarity parameter (relating the horizontal distance to the theoretical point of Mach formation) was found which showed only a small influence of burst height on the path of the triple point. While the data presented provide knowledge of the effect of many surface-roughness elements on the overall shock characteristics, the data do not provide insight into the details of the air-flow characteristics along the surface, nor the relative contribution of individual roughness elements to the results obtained.

Huber, Paul W↗
NASA NTRS1961

Preliminary Base Pressures Obtained from the X-15 Airplane at Mach Numbers from 1.1 to 3.2

Base pressure measurements have been made on the fuselage, 10 deg.-wedge vertical fin, and side fairing of the X-15 airplane. Data are presented for Mach numbers between 1.1 and 3.2 for both powered and unpowered flight. Comparisons are made with data from small-scale-model tests, semiempirical estimates, and theory. The results of this preliminary study show that operation of the interim rocket engines (propellant flow rate approximately 70 lb/sec) reduces the base drag of the X-15 by 25 to 35 percent throughout the test Mach number range. Values of base drag coefficient for the side fairing and fuselage obtained from X-15 wind-tunnel models were adequate for predicting the overall full-scale performance of the test airplane. The leading-edge sweep of the upper movable vertical fin was not an important factor affecting the fin base pressure. The power-off base pressure coefficients of the upper movable vertical fin (a 10 deg. wedge with chord-to-thickness ratio of 5.5 and semispan-to-thickness ratio of 3.2) are in general agreement with the small-scale blunt-trailing-edge-wing data of several investigators and with two-dimensional theory.

Saltzman, Edwin J.↗
NASA NTRS1959

An Investigation of the Performance of Various Reaction Control Devices

An investigation of a small-scale reaction control devices in still air with both subsonic and supersonic internal flows has shown that lateral forces approaching 70 percent of the resultant force of the undeflected jet can be obtained. These results were obtained with a tilted extension at a deflection of 40 deg. The tests of tilted extensions indicated an optimum length-to-diameter ratio of approximately 0.75 to 1.00, dependent upon the deflection angle. For the two geometric types of spoiler tabs tested, blockage-area ratio appears to be the only variable affecting the lateral force developed. Usable values of lateral force were developed by the full-eyelid type of device with reasonably small losses in the thrust and weight flow. Somewhat larger values of lateral force were developed by injecting a secondary flow normal to the primary jet, but for conditions of these tests the losses in thrust and weight flow were large. Relatively good agreement with other investigations was obtained for several of the devices. The agreement of the present results with those of an investigation made with larger-scale equipment indicates that Reynolds number may not be critical for these tests. In as much as the effects of external flow could influence the performance and other factors affecting the choice of a reaction control for a specific use, it would appear desirable to make further tests of the devices described in this report in the presence of external flow.

Hunter, Paul A.↗
NASA NTRS1955

Comparison of the Drag of a Fin-Stabilized Body of Revolution and of a Complete Airplane Configuration as Obtained at Transonic Speeds in a Slotted Wind Tunnel and in Free Flight

A comparison of the zero-lift drag coefficients at Mach numbers from 0.81 to 1.41 of a fin-stabilized parabolic body of revolution as measured in the Langley transonic blowdown tunnel has been made with measurements obtained in free-flight on a larger but geometrically similar model. The absolute values of drag coefficient obtained in the slotted wind tunnel were equivalent to the free-flight drag-coefficient values up to a Mach number of 1.4 when adjustments were made for the effect on viscous drag of differences in Reynolds number between the two test conditions. Excellent agreement was obtained between the two tests for the pressure-drag variation with Mach number, regardless of whether the scale effect on skin friction was considered. Favorable agreement was also obtained between the pressure-drag increments due t o the presence of the stabilizing fins as determined in the wine tunnel from fins-on and fins-off tests and as obtained by a different method in free flight. Tests of a specific airplane configuration to obtain an indication of the problems involved in the construction and tests of small-scale (approximately 7-inch span) complete airplane configuration with internal air flow indicated that reliable zero-lift drag-coefficient measurements at Mach numbers up to 1.4 can be attained with such models, provided the model is constructed with a high but not an unreasonable degree of accuracy.

Howell, Robert R.↗
NASA NTRS1935

Large-Scale Boundary-Layer Control Tests on Two Wings in the NACA 20-Foot Wind Tunnel, Special Report

Tests were made in the N.A.C.A. 20-foot wind tunnel on: (1) a wing, of 6.5-foot span, 5.5-foot chord, and 30 percent maximum thickness, fitted with large end plates and (2) a 16-foot span 2.67-foot chord wing of 15 percent maximum thickness to determine the increase in lift obtainable by removing the boundary layer and the power required for the blower. The results of the tests on the stub wing appeared more favorable than previous small-scale tests and indicated that: (1) the suction method was considerably superior to the pressure method, (2) single slots were more effective than multiple slots (where the same pressure was applied to all slots), the slot efficiency increased rapidly for increasing slot widths up to 2 percent of the wing chord and remained practically constant for all larger widths tested, (3) suction pressure and power requirements were quite low (a computation for a light airplane showed that a lift coefficient of 3.0 could be obtained with a suction as low as 2.3 times the dynamic pressure and a power expenditure less than 3 percent of the rated engine power), and (4) the volume of air required to be drawn off was quite high (approximately 0.5 cubic feet per second per unit wing area for an airplane landing at 40 miles per hour with a lift coefficient of 3,0), indicating that considerable duct area must be provided in order to prevent flow losses inside the wing and insure uniform distribution of suction along the span. The results from the tests of the large-span wing were less favorable than those on the stub wing. The reasons for this were, probably: (1) the uneven distribution of suction along the span, (2) the flow losses inside the wing, (3) the small radius of curvature of the leading edge of the wing section, and (4) the low Reynolds Number of these tests, which was about one half that of the stub wing. The results showed a large increase in the maximum lift coefficient with an increase in Reynolds Number in the range of the tests. The results of drag tests showed that the profile drag of the wing was reduced and the L/D ratio was increased throughout the range of lift coefficients corresponding to take-off and climb but that the minimum drag was increased. The slot arrangement that is best for low drag is not the same, however, as that for maximum lift.

Freeman, Hugh B.↗