Results for “Stokes shift” — Page 3

NASA NTRS1994

Raman-shifting an ArF excimer laser to generate new lines for obtaining optical diagnostic based information in flow fields

The application of tunable excimer lasers in combustion and flow diagnostics is almost routine nowadays. The properties of this laser system that enable density and temperature measurements in supersonic and hypersonic flow fields to be conducted are its high power, high repetition rate, and high spectral brightness. The limitation imposed by this system on these measurements is the paucity of lines in the wavelength region, the vacuum-ultraviolet, where species of interest, such as OH, N2, O2, H2, H2O, CO, NO, etc., are susceptible to electronic excitation to high-lying states. To circumvent this problem one normally resorts to nonlinear optical techniques such as frequency conversion via stimulated Raman scattering (SRS), more commonly known as Raman shifting or Raman mixing, to extend these nonintrusive and nonperturbing techniques to the shorter wavelengths in the VUV region and, for that matter, to longer wavelengths in the infrared region, if the need arises. The theoretical basis of SRS and its application are well documented in the literature. In essence, the Raman shift is a consequence of the inelastic scattering of the incident radiation by the sample. Most of the scattered radiation from the molecules of the sample is unchanged in frequency. However, a small fraction of the incident radiation is changed in frequency. This shift is a result of the fact that some of the incident photons on colliding with the molecules of the sample give up some of their energy and emerge with a lower energy resulting in the lower-frequency Stokes radiation. Other incident photons may increase their energy by colliding with the vibrationally excited molecules of the medium and emerge as higher-frequency antistokes radiation. The generation of the latter is the main objective of this project. The process, however, depends on several factors, including the beam quality of the pump laser, the cross-section of the gaseous medium, the gas pressure, and the ambient temperature of the gas near the focal region. Furthermore, since the Raman shifting process is polarization sensitive, it is necessary to have all of the laser energy in a single polarization. These factors were taken into consideration in the execution of the project. The implementation of the Raman shift was accomplished by focusing the 193 nm output of an ArF excimer laser (Lamda-Physik LPX 150) into a 1-meter long high pressure recirculating Raman cell filled with H2 gas. The laser system was modified in order to improve the mode quality of the pump beam to enhance the Raman shifting. To accomplish this feat, a prism beam expander and grating on the oscillator discharge provided wavelength tuning over the excimer gain profile. Furthermore, a triple-pass configuration, as opposed to unstable resonator optics, was employed in the operation of the amplifier cavity so that when the oscillator output radiation, focused by a 51-cm focal length fused silica lens through a 50 micron pinhole (serving as a spatial filter) and recollimated with a 25-cm focal length lens, was fed into the amplifier, it was injection locked, thereby providing tunable radiation with relatively low divergence. The forward scattered radiation emanating from the impingement of the modified pump beam on the Raman cell was detected using an energy meter after the latter had been separated from it using a dispersing prism.

Koker, Edmond B.↗

NASA NTRS1985

Measurements of distributed polarized radio sources from spinning spacecraft - Effect of a tilted axial antenna ISEE-3 application and results

An analysis is presented of the system response of a satellite receiver-antenna system to locate a radio source when the satellite is tilted on its axis. The satellite is spin stabilized but experiences a tilt due to either a mechanical misalignment or a shift in the electrical axis caused by parasitic currents in other spacecraft structures. The shorter the antenna, the more significant the effects. Numerical techniques are developed for obtaining the Stokes parameters and the angular parameters of a uniform conical source sensed by a linear antenna in order to derive the average power response of a synthesized dipole to a point on a distributed polarized source. Relative gains are calculated along the antenna at different angles to the source. The techniques are applied to sample ISEE-3 satellite data for Type III solar radio bursts which were sensed by an axial and an equatorial antenna. The two antennas permit localization of the source and quantification of the polarization and angular extent of the source. The resulting high precision in calculations of all three source parameters commends use of the model in analyses of data from the planned ULYSSES mission.

Fainberg, J.↗

NASA NTRS2011

USM3D Analysis of Low Boom Configuration

In the past few years considerable improvement was made in NASA's in house boom prediction capability. As part of this improved capability, the USM3D Navier-Stokes flow solver, when combined with a suitable unstructured grid, went from accurately predicting boom signatures at 1 body length to 10 body lengths. Since that time, the research emphasis has shifted from analysis to the design of supersonic configurations with boom signature mitigation In order to design an aircraft, the techniques for accurately predicting boom and drag need to be determined. This paper compares CFD results with the wind tunnel experimental results conducted on a Gulfstream reduced boom and drag configuration. Two different wind-tunnel models were designed and tested for drag and boom data. The goal of this study was to assess USM3D capability for predicting both boom and drag characteristics. Overall, USM3D coupled with a grid that was sheared and stretched was able to reasonably predict boom signature. The computational drag polar matched the experimental results for a lift coefficient above 0.1 despite some mismatch in the predicted lift-curve slope.

Carter, Melissa B.↗

NASA NTRS1993

Pulsed laser Rayleigh scattering diagnostic for hydrogen/oxygen rocket exit plane flowfield velocimetry

A Doppler-resolved, pulsed laser Rayleigh scattering diagnostic has been developed to obtain local flowfield velocity measurements at the exit plane of a low thrust hydrogen/oxygen rocket engine operating in a high-altitude test facility. Fiberoptic signal collection was employed to obtain the forescatter and backscatter Doppler shifts necessary to resolve the axial and radial velocity components. A radial profile was obtained by traversing the collection probes along the beam path at the nozzle exit. The results are compared with theoretical predictions from a full Navier-Stokes model (RK/RPLUS). Significant discrepancies between the measured and predicted axial velocity profiles are observed, in terms of both magnitude and character. Radial velocity measurements exhibit excellent agreement with predictions near the centerline but show some departure off-axis. The discrepancies between theory and experiment are potentially the result of enhanced mixing between the core and fuel-film region beyond that predicted, and/or flow stratification between the hydrogen and oxygen injected into the central core region.

Zupanc, Frank J.↗

NASA NTRS1987

Raman-shifted dye laser for water vapor DIAL measurements

For improved DIAL measurements of water vapor in the upper troposphere or lower stratosphere, narrowband (about 0.03/cm) laser radiation at 720- and 940-nm wavelengths was generated by stimulated Raman scattering (SRS), using the narrow linewidth (about 0.02/cm) output of a Nd:YAG-pumped dye laser. For a hydrogen pressure of 350 psi, the first Stokes conversion efficiencies to 940 nm were 20 percent and 35 percent, when using a conventional and waveguide Raman cell, respectively. The linewidth of the first Stokes line at high cell pressures, and the inferred collisional broadening coefficients, agree well with those previously measured in spontaneous Raman scattering.

Grossmann, B. E.↗

NASA NTRS1992

Rocket plume flowfield characterization using laser Rayleigh scattering

A Doppler-resolved laser Rayleigh scattering diagnostic was applied to a 111 N thrust, regenerative and fuel-film cooled, gaseous hydrogen/gaseous oxygen rocket engine. The axial and radial mean gas velocities were measured from the net Doppler shifts observed for two different scattering angles. Translational temperatures and number densities were estimated from the Doppler widths and scattered intensities, respectively, by assuming that water was the dominant scattering species in the exhaust. The experimental results are compared with theoretical predictions from a full Navier-Stokes code (RD/RPLUS) and the JANNAF Two-Dimensional Kinetics (TDK) and Standardized Plume Flowfield (SPF-II) codes. Discrepancies between the measured and predicted axial velocities, temperatures, and number densities are evident. Radial velocity measurements, however, show excellent agreement with predictions. The discrepancies are attributed primarily to inefficient mixing and combustion caused by the injection of excessive oxidizer along one side of the thrust chamber. Thrust and mass flow rate estimates obtained from the Rayleigh measurements show excellent agreement with the globally measured values.

Zupanc, Frank J.↗

NASA NTRS1992

Rocket plume flowfield characterization using laser Rayleigh scattering

A Doppler-resolved laser Rayleigh scattering diagnostic was applied to a 111 N thrust, regenerative and fuel-film cooled, gaseous hydrogen/gaseous oxygen rocket engine. The axial and radial mean gas velocities were measured from the net Doppler shifts observed for two different scattering angles. Translational temperatures and number densities were estimated from the Doppler widths and scattered intensities, respectively, by assuming that water was the dominant scattering species in the exhaust. The experimental results are compared with theoretical predictions from a full Navier-Stokes code (RD/RPLUS) and the JANNAF Two-Dimensional Kinetics (TDK) and Standardized Plume Flowfield (SPF-II) codes. Discrepancies between the measured and predicted axial velocities, temperatures, and number densities are evident. Radial velocity measurements, however, show excellent agreement with predictions. The discrepancies are attributed primarily to inefficient mixing and combustion caused by the injection of excessive oxidizer along one side of the thrust chamber. Thrust and mass flow rate estimates obtained from the Rayleigh measurements show excellent agreement with the globally measured values.

Zupanc, Frank J.↗

NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

Boundary layer transition↗

NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

boundary layer transition↗

NASA NTRS2023

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

boundary layer transition↗

NASA NTRS2000

Numerical Simulation of Receptivity for a Transition Experiment

The cost of fuel to overcome turbulence induced viscous drag on a commercial airplane constitutes a significant fraction of the operating cost of an airline. Achieving laminar flow and maintaining it over a large portion of the wing can significantly reduce the viscous drag, and hence the cost. Design of such laminar-flow-control wings and their practical operation requires the ability to accurately and reliably predict the transition from laminar to turbulent flow. The transition process begins with the conversion of environmental and surface disturbances into the instability waves of the flow by a process called receptivity. The goal of the current research project has been to improve the prediction of transition through a better understanding of the physics of receptivity. The initial objective of this work was to investigate the specific stability and receptivity characteristics of a particular experimental investigation of boundary layer receptivity at NASA Langley. Some simulation results using direct solutions of the linearized Navier-Stokes equations which modeled this experiment where presented in the 1999 APS DFD meeting. However, based on these initial investigations, it became clear that to cover the vast receptivity parameter space required for a practical transition prediction tool, more efficient methods would be required. Thus, the focus of this research was shifted from modeling this particular experiment to formulating and developing new techniques that could efficiently yet accurately predict receptivity for a wide range of disturbance conditions.

Collis, S. Scott↗

NASA NTRS2008

Hybrid LES/RANS Simulation of Transverse Sonic Injection into a Mach 2 Flow

A computational study of transverse sonic injection of air and helium into a Mach 1.98 cross-flow is presented. A hybrid large-eddy simulation / Reynolds-averaged Navier-Stokes (LES/RANS) turbulence model is used, with the two-equation Menter baseline (Menter-BSL) closure for the RANS part of the flow and a Smagorinsky-type model for the LES part of the flow. A time-dependent blending function, dependent on modeled turbulence variables, is used to shift the closure from RANS to LES. Turbulent structures are initiated and sustained through the use of a recycling / rescaling technique. Two higher-order discretizations, the Piecewise Parabolic Method (PPM) of Colella and Woodward, and the SONIC-A ENO scheme of Suresh and Huyhn are used in the study. The results using the hybrid model show reasonably good agreement with time-averaged Mie scattering data and with experimental surface pressure distributions, even though the penetration of the jet into the cross-flow is slightly over-predicted. The LES/RANS results are used to examine the validity of commonly-used assumptions of constant Schmidt and Prandtl numbers in the intense mixing zone downstream of the injection location.

Boles, John A.↗

NASA NTRS1989

Optical Stark effect in the four-wave mixing and stimulated Raman spectra of N2

The influence of the optical Stark effect on spectral line shapes in four-wave-mixing Raman spectroscopy (FWMRS) and stimulated Raman spectroscopy (SRS) is investigated experimentally and theoretically. Using an experimental setup capable of rapid alternation between the simultaneous measurement of coherent Stokes Raman spectroscopy and inverse Raman spectroscopy at low and high intensities, together with a sophisticated frequency reference scheme, it was possible to perform a rather direct comparison between Stark-broadened and non-Stark-broadened spectra of both classes of Raman spectroscopies. The results demonstrate that SRS spectra show more Stark shift and broadening than their FWMRS counterparts. A discrepancy with theoretical results is pointed out, and an attempt is made to explain it.

Moosmuller, H.↗

NASA NTRS1982

The indirect effects on the computation of geoid undulations

The indirect effects on the geoid computation due to the second method of Helmert's condensation were studied. when Helmert's anomalies are used in Stokes's equation, there are three types of corrections to the free air geoid. The first correction, the indirect effect on geoid undulation due to the potential change in Helmert's reduction, had a maximum value of 0.51 meters in the test area covering the United States. The second correction, the attraction change effect on geoid undulation, had a maximum value of 9.50 meters when the 10 deg cap was used in Stokes' equation. The last correction, the secondary indirect effect on geoid undulatin, was found negligible in the test area. The corrections were applied to uncorrected free air geoid undulations at 65 Doppler stations in the test area and compared with the Doppler undulations. Based on the assumption that the Doppler coordinate system has a z shift of 4 meters with respect to the geocenter, these comparisons showed that the corrections presented in this study yielded improved values of gravimetric undulations.

Wichiencharoen, C.↗

NASA NTRS1999

Horizontal Wavenumber Spectra of Winds, Temperature and Trace Gases During the Pacific Exploratory Missions: Gravity Waves, Quasi-Two-Dimensional Turbulence, and Vortical Modes - 2

We examine the horizontal wavenumber spectra of horizontal velocity and potential temperature collected by aircraft above the Pacific Ocean to determine whether gravity waves, quasi-two-dimensional (Q-2-D) turbulence, or vortical modes dominate atmospheric fluctuations at scale sizes of 1-100 km and altitudes of 2-12 km. We conclude from the study of Doppler-shifting effects that Q-2-D turbulence and/or vortical modes are more prevalent than gravity waves over the ocean, except in the equatorial zone. The results are consistent with recent numerical simulations of Q-2-D turbulence, which show that the characteristic inverse cascade of energy is greatly facilitated by the presence of background rotation. Furthermore, a Stokes-parameter analysis reveals the general paucity of coherent wavelike motions, although specific cases of gravity-wave propagation are observed. Finally, a case study of a long flight segment displays a k(sup -3) horizontal velocity variance spectrum at scales longer than about 100 km. A Stokes-parameter analysis indicates that these large-scale fluctuations were likely due to vortical modes rather than inertio-gravity waves.

Cho, John Y. N.↗

NASA NTRS2004

Modeling of Turbulence Generated Noise in Jets

A numerically calculated Green's function is used to predict jet noise spectrum and its far-field directivity. A linearized form of Lilley's equation governs the non-causal Green s function of interest, with the non-linear terms on the right hand side identified as the source. In this paper, contributions from the so-called self- and shear-noise source terms will be discussed. A Reynolds-averaged Navier-Stokes solution yields the required mean flow as well as time- and length scales of a noise-generating turbulent eddy. A non-compact source, with exponential temporal and spatial functions, is used to describe the turbulence velocity correlation tensors. It is shown that while an exact non-causal Green's function accurately predicts the observed shift in the location of the spectrum peak with angle as well as the angularity of sound at moderate Mach numbers, at high subsonic and supersonic acoustic Mach numbers the polar directivity of radiated sound is not entirely captured by this Green's function. Results presented for Mach 0.5 and 0.9 isothermal jets, as well as a Mach 0.8 hot jet conclude that near the peak radiation angle a different source/Green's function convolution integral may be required in order to capture the peak observed directivity of jet noise.

Khavaran, Abbas↗

NASA NTRS2023

Large Photospheric Doppler Shift in Solar Active Region 12673: I. Field-Aligned Flows

Delta (δ) sunspots sometimes host fast photospheric flows along the central magnetic polarity inversion line (PIL). Here we study the strong Doppler shift signature in the central penumbral light bridge of solar active region NOAA 12673. Observations from the Helioseismic and Magnetic Imager (HMI) indicate highly sheared, strong magnetic fields. Large Doppler shifts up to 3.2 km s −1 appeared during the formation of the light bridge and persisted for about 16 hours. A new velocity estimator, called DAVE4VMwDV, reveals fast converging and shearing motion along the PIL from HMI vector magnetograms, and recovers the observed Doppler signal much better than an old version of the algorithm. The inferred velocity vectors are largely (anti-)parallel to the inclined magnetic fields, suggesting that the observed Doppler shift contains significant contribution from the projected, field-aligned flows. High-resolution observations from the Hinode/Spectro-Polarimeter (SP) further exhibit a clear correlation between the Doppler velocity and the cosine of the magnetic inclination, which is in agreement with HMI results and consistent with a field-aligned flow of about 9.6 km s −1 . The complex Stokes profiles suggest significant gradients of physical variables along the line of sight. We discuss the implications on the δ-spot magnetic structure and the flow-driving mechanism.

Solar active region magnetic fields↗

NASA NTRS1992

Infrared Pulse-laser Long-path Absorption Measurement of Carbon Dioxide Using a Raman-shifted Dye Laser

A pulsed laser source is effective in infrared laser long-path absorption measurements when the optical path length is very long or the reflection from a hard target is utilized, because higher signal-to-noise ratio is obtained in the detection of weak return signals. We have investigated the performance of a pulse-laser long-path absorption system using a hydrogen Raman shifter and a tunable dye laser pumped by a Nd:YAG laser, which generates second Stokes radiation in the 2-micron region.

Minato, Atsushi↗