Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stress relaxation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Stress Relaxation Cracking in 347H Stainless Steel Arc Welds: Susceptibility Evaluation of Heat-Affected Zone

Stress relaxation cracking (SRC) is considered one of the major failure mechanisms for 347H stainless steel welds at elevated service temperatures or during post weld heat treatment (PWHT), especially within the heat-affected zone (HAZ). This work focuses on the characterization of SRC susceptibility within 347H physically simulated arc welded HAZ at elevated temperatures. A four-step SRC thermomechanical test in combination with finite element modeling (FEM) of the welding and testing processes is developed to establish a susceptibility map for HAZ. The test first runs a thermal cycle with three different peak temperatures (1335, 1275, and 1150 °C) to duplicate representative HAZ subzone microstructures, followed by time-to-failure examination under a variety of pre-stress (260–600 MPa) and pre-strain conditions (0.03–0.19) as a function of reheat temperatures between 750 and 1050 °C. With the aid of FEM, SRC susceptibility maps are generated to identify the threshold stress, plastic strain, and creep strain as a function of test temperature. It was found out that HAZ subzone with a lower peak temperature (1150 °C) appears to be slightly less susceptible to SRC than the other two subzones that experienced higher peak temperatures. Generally, time-to-fracture reduces with increasing initially applied stress and strain for all test temperatures. The pre-stress thresholds decrease from about 500 to 330 MPa as the testing temperature increases from 800 to 1050 °C, while the corresponding initial plastic strain thresholds reduces from 0.15 to 0.06. The SRC susceptibility was also evaluated through the Larson–Miller Parameter (LMP) analysis as a function of plastic strain, initial stress and starting stress upon reaching the testing temperature, respectively. The 1050 °C test with a high pre-applied strain (0.1) exhibits an extremely short time to failure (t = 3 s) that lies outside the general trend in LMP analysis. Additionally, it was identified that a plastic strain above 0.07 is identified to significantly reduce the bulk creep strain tolerance to fracture and therefore increases SRC susceptibility. Hardness measurement and fractography analysis indicated that the strain aging of niobium carbonitrides and other potential phases in conjunction with intergranular precipitates contributes to an increase in microhardness and increased intergranular cracking susceptibility.

14 SOLAR ENERGY↗
DOE OSTI2025

Predicting long-term stress relaxation on Alloy 709 using the crystal plasticity finite element method

This report summarizes the results of physics-based, crystal plasticity simulations for the long-term stress relaxation behavior of Alloy 709. The purpose of the study was to provide insight into five key questions related to long-term behavior in high temperatures materials which are difficult or impossible to answer experimentally: (1) is there a threshold stress for long-term relaxation? (2) is there strain threshold for relaxation damage, below which significant damage does not accumulate? (3) does damage continue to accumulate as the material relaxes or will damage accumulation plateau under some loading conditions? (4) does stress relaxation loading inevitably lead to failure? and (5) which, if any, engineering models for relaxation damage accumulation reasonably match the simulation results? The report summarizes the numerical simulations used to address these five questions and provides at least partial answers to each question.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Intermediate time sub-diffusion and stress relaxation in ring polymer melts

The slow dynamics of non-concatenated ring melts remains a frontier problem in polymer science with implications for many soft material environments including cellular biophysics. Here, in this work, we report large-scale simulations of model ring melts that analyze the monomer and center-of-mass (CM) mean square displacements (MSD) and stress relaxation function on intermediate time and length scales. The degree of dynamical slowing down is characterized by the maximally sub-diffusive fractional time scaling exponents. The data span an exceptionally wide range of ring degrees of polymerization and stiffnesses and are not successfully organized based on the classic measure linear chain entanglement, N/N e . Rather, we find that the crossover degree of polymerization, N D , based on ring macromolecular caging that successfully allows master curves to be constructed for the long-time CM self-diffusion constant also collapses these temporal dynamic scaling exponents. Different properties display different exponents and exhibit one or two regimes of linear variation with the logarithm of N D / N . A distinct crossover of the CM-MSD and stress relaxation exponents emerges at sufficiently large N or stiffness that is not found for the monomer MSD, indicating a novel form of dynamic decoupling. This crossover aligns with the predicted critical degree of polymerization for transitioning from a weak to strong caging regime, indicative of activated transport. The latter may reflect the emergence of an intermolecular collective contribution to stress in analogy with dense soft colloidal matter. Suggestions are made for future theoretical work to address the rich patterns of behavior discovered.

Anomalous diffusion↗
NASA NTRS2007

Modeling Creep-Induced Stress Relaxation at the Leading Edge of SiC/SiC Airfoils

Anticipating the implementation of advanced SiC/SiC composites into internally cooled airfoil components within the turbine section of future aero-propulsion engines, the primary objective of this study was to develop physics-based analytical and finite-element modeling tools to predict the effects of composite creep and stress relaxation at the airfoil leading edges, which will generally experience large thermal gradients at high temperatures. A second objective was to examine how some advanced NASA-developed SiC/SiC systems coated with typical EBC materials would behave as leading edge materials in terms of long-term steady-state operating temperatures. Because of the complexities introduced by mechanical stresses inherent in internally cooled airfoils, a simple cylindrical thin-walled tube model subjected to thermal stresses only is employed for the leading edge, thereby obtaining a best-case scenario for the material behavior. In addition, the SiC/SiC composite materials are assumed to behave as isotropic materials with temperature-dependent viscoelastic creep behavior as measured in-plane on thin-walled panels. Key findings include: (1) without mechanical stresses and for typical airfoil geometries, as heat flux is increased through the leading edge, life-limiting tensile crack formation will occur first in the hoop direction on the inside wall of the leading edge; (2) thermal gradients through all current SiC/SiC systems should be kept below approx.300 F at high temperatures to avoid this cracking; (3) at temperatures near the maximum operating temperatures of advanced SiC/SiC systems, thermal stresses induced by the thermal gradients will beneficially relax with time due to creep; (4) although stress relaxation occurs, the maximum gradient should still not exceed 300oF because of residual tensile stress buildup on the airfoil outer wall during cool-down; and (5) without film cooling and mechanical stresses, the NASA-developed N26 SiC/SiC system with thru-thickness Sylramic-iBN fiber reinforcement and a typical EBC coating has the potential of offering a maximum long-term steady-state operating temperature of approx.3100 F at the surface of the EBC.

Lang, Jerry↗
NASA NTRS1981

Creep recovery and stress relaxation tests of 6061-0 aluminum

The investigation of creep recovery and stress relaxation in aluminum using a closed loop servo-hydraulic test system is described. The practicality of a computer controlled test system for constant plastic strain rate tension tests is demonstrated. The plastic strain rate and the magnitude of the initial strain are shown to have a noticeable effect on subsequent creep behavior of aluminum.

Wu, H. C.↗
DOE OSTI2022

Predicting variations of the least principal stress with depth: Application to unconventional oil and gas reservoirs using a log-based viscoelastic stress relaxation model

Knowledge of layer-to-layer variations of the least principal stress, S hmin , with depth is essential for optimization of multi-stage hydraulic fracturing in unconventional reservoirs. Utilizing a geomechanical model based on viscoelastic stress relaxation in relatively clay rich rocks, we present a new method for predicting continuous S hmin variations with depth. The method utilizes geophysical log data and S hmin measurements from routine diagnostic fracture injection tests (DFITs) at several depths for calibration. We consider a case study in the Wolfcamp formation in the Midland Basin, where both geophysical logs and values of S hmin from DFITs are available. We compute a continuous stress profile as a function of the well logs that fits all of the DFITs well. We utilized several machine learning technologies, such as bootstrap aggregation (or bagging), to improve the generalization of the model and demonstrate that the excellent fit between predicted and observed stress values is not the result of over-fitting the calibration points. The model is then validated by accurately predicting hold-out stress measurements from four wells within the study area and, without recalibration, accurately predicting stress as a function of depth in an offset pad about 6 miles away.

58 GEOSCIENCES↗
DOE OSTI2024

Stress Relaxation Cracking of Alloys at Temperatures Higher Than 540°C

Type 347H stainless steel (347H SS), used in commercial concentrating solar power (CSP) thermal energy storage to store solar-salt at a temperature of 565°C, has been reported in the literature to be susceptible to stress-relaxation cracking (SRC). The welded heat-affected zone (HAZ) and fusion zone (FZ) of 347H SS, particularly in thick sections, are known to be susceptible to failure during post-weld heat treatment (reheat cracking). SRC could also occur after months or years under an elevated-temperature service environment. Two conditions must be present for failure to occur in the HAZ and/or FZ: 1) a modified or sensitized microstructure and 2) sufficiently high tensile residual stresses present at the elevated service temperature. The overarching goal of this project is to recommend SRC mitigation protocols to avoid susceptibility to fail through SRC at temperatures relevant for CSP. Post weld heat treatment conditions and alternative alloys are investigated as potential mitigation solutions to SRC. We used Gleeble thermomechanical simulation tests and finite element (FE) models to understand the susceptibility of 347H SS to SRC as a function of temperature, stress, and microstructure. We started with a literature review of weldability issues with 347H SS and techniques to mitigate SRC in 347H SS weldments. Next, we used Gleeble experiments to determine reheat cracking susceptibility in the simulated HAZ of 347SS weldments and an alternative alloy, 316L SS (NUCL 167 SPH) with boron added. We also performed Gleeble experiments to compare the reheat cracking susceptibility of 347H cross welded with two different fillers: E347, which is used in some commercial CSP TES tanks, and E16.8.2. We validated the experimental results with FE models of the residual stresses. We found that although the 316L (NUCL 167 SPH) is less susceptible to reheat cracking, it is slightly weaker than 347H and ASME BP&V codes limit its use to a service condition of 565°C. We also found that welds using E16.8.2 as the weld filler are less susceptible to failure than those using E347, likely due to the higher creep ductility of E16.8.2, and that it may be used as an alternative filler for repair welding of 347H welds or as the primary choice of filler for newly developed weld joints. We also found that post weld heat treatment could be a viable solution for mitigating stress in E347-347H SS thick, constrained welds, like those found in CSP tanks, and propose several options for mitigating SRC in existing and future TES tanks.

14 SOLAR ENERGY↗
NASA NTRS1981

Long-time stress relaxation of a filled elastomer in vacuum environments

Samples of a filled elastomeric ablative material were stored at 45 C and 10 to the -6th torr for 7 months. Their tensile stress-relaxation modulus at constant strain was measured throughout the 7 months. Results of the testing are discussed primarily by comparisons of the data to atmospheric-pressure moduli (determined in this work for shorter periods of time) and with moduli predicted from short-time testing. Confirmation of the strengthening effects of vacuum on this composite was obtained. The use of time-temperature superposition techniques as an approximate accelerated testing procedure for this material under these conditions was also verified.

Ward, T. C.↗
DOE OSTI2020

Determination of Stress-Free Lattice Spacing (D₀) for Residual Stress Relaxation Measurement in Ni-based Superalloys by Neutron Diffraction

The residual stress and its relaxation in critical engineering components are key to structural materials reliability. The determination of residual stress in bulk engineering structures like Ni-based superalloys can be conducted by measuring the lattice strain with penetrating neutron diffraction. The state-of-the-art engineering diffraction beamline VULCAN at the Oak Ridge National Laboratory (ORNL) Spallation Neutron Source (SNS) provides the critical capability to evaluate the residual strain/stress relaxation in engineering component thanks to the high flux and event data features. By the means of residual stress/strain calculation, it is critical to accurately determine the stress-free lattice spacing d₀, which can be altered by the change of chemistry, unrelieved stress, and measurement scheme. Here we reported d₀ determination for determining residual stress relaxation and distribution in Alloy 718 superalloys after different quenching treatments. Selection of locations for d₀ measurement was discussed by considering the neutron path, attenuation and sample alignment. A dynamic d₀ that resulted from atom diffusion and chemistry change was estimated as function of time for the in-situ relaxation characterization. It demonstrated how the dynamic d₀ values may influence on the strain calculation in different thermally treated samples. The results highlight the importance of dynamic d₀ for in-situ relaxation involving chemical changes and provide guidance to the dynamic d₀ measurement and simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Discrete Measurements of the Least Horizontal Principal Stress from Core Data: An Application of Viscoelastic Stress Relaxation

Summary The emerging Paradox Oil Play in southeastern Utah is among the most significant unconventional plays in the western USA. The mean total undiscovered oil resources within just the Pennsylvanian Cane Creek interval of the Paradox Basin are believed to exceed 215 million barrels. However, to date, less than 5% (~9 million barrels) of the total Cane Creek resource has been produced from fewer than 40 wells, and only approximately one-half of those are horizontal wells. More than 95% of production is from the central Cane Creek Unit (CCU). Natural fractures are a key feature of many production wells, but stimulation by induced hydraulic fractures is not consistently successful. We hypothesize that more effective production in this play will rely on better fundamental characterization, especially on better quantification of the state of stress. Approximately 110 ft of core, well logs, and a diagnostic fracture injection test (DFIT) were acquired from the State 16-2 well within the CCU. With these data, we applied two methods to constrain and clarify the state of stress. The first technique, the Simpson’s coefficient method, provides lower bounds on the two horizontal principal stresses and relies on only limited data. Alternatively, the viscoelastic stress relaxation (VSR) method is used to estimate the least horizontal principal stress, building on observations that principal stresses become more isotropic as the viscous behavior of a rock is more pronounced. Results of these two methods support the hypothesis that the state of stress in the CCU of the Paradox Basin is nearly lithostatic and isotropic. Other factors consistent with this hypothesis include high formation pore pressure, which tends to reduce the possible stress states by changing the frictional failure equilibrium; lack of induced fractures in the core, which should be present in the case of stress anisotropy; and interbedded halite layers, which given their high degree of ductility, probably lead to greater VSR for the entire sedimentary package.

Energy & Fuels↗
DOE OSTI2020

Microscopic dynamics of stress relaxation in a nanocolloidal soft glass

Here, we report x-ray photon correlation spectroscopy (XPCS) experiments with in situ rheometry performed on a soft glass composed of a concentrated suspension of charged silica nanoparticles subjected to step strains that induce yielding and flow. The XPCS measurements characterize the particle-scale and mesoscale motions within the glass that underlie the highly protracted decay of the macroscopic stress following the step strains. These dynamics are anisotropic, with slow, convective particle motion along the direction of the preceding shear that persists for surprisingly large times and that is accompanied by intermittent motion in the perpendicular (vorticity) direction. A close correspondence between the convective dynamics and stress relaxation is demonstrated by power-law scaling between the characteristic velocity of the collective particle motion and the rate of stress decay.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Factors Influencing Propensity for Stress Relaxation Cracking in Inconel® Alloy 740H® and Practical Guidance for Applications

Inconel® alloy 740H® (UNS N07740) was the first age-hardenable nickel-based alloy approved by the ASME Boiler & Pressure Vessel Code for use in pressure-boundary applications. In recent years, advanced energy systems such as supercritical CO2 power cycles have utilized alloy 740H in large demonstration projects driven by the requirement for higher fluid temperatures and pressures. Stress relaxation cracking (SRxC) following post-weld heat-treatment (PWHT), also known as strain age cracking (SAC), has been identified in a limited number of weldments during these industrial builds resulting in focused research to further clarify factors influencing this cracking tendency. This paper will summarize some of the findings from shop and field fabrication leading to successful welds and characteristics of observed SRxC. Laboratory experiments supported by microstructural characterization will be presented to highlight the importance of variables such as strain, material starting condition, and PWHT temperatures. Finally, the results will be summarized within the context of practical guidance for industry to successfully weld the material in boiler, heat exchanger, and piping applications.

14 SOLAR ENERGY↗
NASA NTRS1971

Long-term aging of elastomers: Chemical stress relaxation of fluorosilicone rubber and other studies

Aerospace applications of elastomers are considered, including: propellant binders, bladder materials for liquid propellant expulsion systems, and fuel tank sealants for high-speed aircraft. A comprehensive molecular theory for mechanical properties of these materials has been developed but has only been tested experimentally in cases where chemical degradation processes are excluded. Hence, a study is being conducted to ascertain the nature, extent, and rate of chemical changes that take place in some elastomers of interest. Chemical changes that may take place in the fluorosilicone elastomer, LS 420, which is regarded as a fuel and high-temperature-resistant rubber are investigated. The kinetic analysis of the chemical stress relaxation and gel permeation chromatography studies comprise the major portion of the report.

Kalfayan, S. H.↗
NASA NTRS2004

Deformation, Stress Relaxation, and Crystallization of Lithium Silicate Glass Fibers Below the Glass Transition Temperature

The deformation and crystallization of Li(sub 2)O (center dot) 2SiO2 and Li(sub 2)O (center dot) 1.6SiO2 glass fibers subjected to a bending stress were measured as a function of time over the temperature range -50 to -150 C below the glass transition temperature (Tg). The glass fibers can be permanently deformed at temperatures about 100 C below T (sub)g, and they crystallize significantly at temperatures close to, but below T,, about 150 C lower than the onset temperature for crystallization for these glasses in the no-stress condition. The crystallization was found to occur only on the surface of the glass fibers with no detectable difference in the extent of crystallization in tensile and compressive stress regions. The relaxation mechanism for fiber deformation can be best described by a stretched exponential (Kohlrausch-Williams-Watt (KWW) approximation), rather than a single exponential model.The activation energy for stress relaxation, Es, for the glass fibers ranges between 175 and 195 kJ/mol, which is considerably smaller than the activation energy for viscous flow, E, (about 400 kJ/mol) near T, for these glasses at normal, stress-free condition. It is suspected that a viscosity relaxation mechanism could be responsible for permanent deformation and crystallization of the glass fibers below T,

Ray, Chandra S.↗