Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Computational Fluid Dynamics Study of a Cross-Flow Marine Hydrokinetic Turbine and the Combined Influence of Struts and Helical Blades

A computational fluid dynamics study was performed for a cross-flow marine hydrokinetic turbine. The analysis was done in three dimensions and used the unsteady Reynolds-averaged Navier-Stokes solver in the commercial code STAR-CCM+. The base turbine configuration is the RivGen(R) Turbine, designed by the Ocean Renewable Power Company. A convergence and uncertainty analysis was performed for both the spatial and temporal discretization; this was done using the base configuration, which features support struts and helical foils. Both struts and helical blades introduce three-dimensional flow effects, influencing the complex flow phenomenon of dynamic stall. The study compares the relative impact of struts on power performance and blade loading for both helical and straight blades, and found that for this turbine the relative loss in power from struts was lower with helical blades.

CFD↗

Exploratory tests of two strut fuel injectors for supersonic combustion

Results of supersonic mixing and combustion tests performed with two simple strut injector configurations, one with parallel injectors and one with perpendicular injectors, are presented and analyzed. Good agreement is obtained between static pressure measured on the duct wall downstream of the strut injectors and distributions obtained from one-dimensional calculations. Measured duct heat load agrees with results of the one-dimensional calculations for moderate amounts of reaction, but is underestimated when large separated regions occur near the injection location. For the parallel injection strut, good agreement is obtained between the shape of the injected fuel distribution inferred from gas sample measurements at the duct exit and the distribution calculated with a multiple-jet mixing theory. The overall fraction of injected fuel reacted in the multiple-jet calculation closely matches the amount of fuel reaction necessary to match static pressure with the one-dimensional calculation. Gas sample measurements with the perpendicular injection strut also give results consistent with the amount of fuel reaction in the one-dimensional calculation.

Anderson, G. Y.↗

Normal injection of helium from swept struts into ducted supersonic flow

Recent design studies have shown that airframe-integrated scramjets should include instream mounted, swept-back strut fuel injectors to obtain short combustors. Because there was no data in the literature on mixing characteristics of swept strut fuel injectors, the present investigation was undertaken to provide such data. This investigation was made with two swept struts in a closed duct at Mach number of 4.4 and nominal jet-to-air mass flow ratio of 0.029 with helium used to simulate hydrogen fuel. The data is compared with flat plate mounted normal injector data to obtain the effect of swept struts on mixing. Three injector patterns were evaluated representing the range of hole spacing and jet-to-freestream dynamic pressure ratio of interest. Measured helium concentration, pitot pressure, and static pressure in the downstream mixing region are used to generate contour plots necessary to define the mixing region flow field and the mixing parameters.

Mcclinton, C. R.↗

Subscale, hydrogen-burning, airframe-integrated-scramjet: Experimental and theoretical evaluation of a water cooled strut airframe-integrated-scramjet: Experimental leading edge

A water-cooled leading-edge design for an engine/airframe integrated scramjet model strut leading edge was evaluated. The cooling design employs a copper cooling tube brazed just downstream of the leading edge of a wedge-shaped strut which is constructed of oxygen-free copper. The survival of the strut leading edge during a series of tests at stagnation point heating rates confirms the practicality of the cooling design. A finite difference thermal model of the strut was also proven valid by the reasonable agreement of calculated and measured values of surface temperature and cooling-water heat transfer.

Pinckney, S. Z.↗

Boron-epoxy-reinforced titanium aircraft landing-gear drag strut

The structural performance of a boron-epoxy-reinforced titanium drag strut, containing a bonded scarf joint and designed to the criteria of a large commercial transport, has been evaluated experimentally and analytically. The strut was exposed to two lifetimes of fatigue loading and was statically loaded to the tensile and compressive design ultimate loads. Throughout the test program no evidence of any damage in the drag strut was detected by strain-gage measurements, ultrasonic inspection, or visual observation. The bonded joint was analyzed using the NASTRAN computer program. A comparison of the strains predicted by the NASTRAN computer program with the experimentally determined values shows excellent agreement. An analytical study indicated that the nonlinear behavior of a structural spacer at each end of the strut could be explained by the inelastic behavior and possible creep of the adhesive.

Howell, W. E.↗

Preliminary design characteristics of a subsonic business jet concept employing an aspect ratio 25 strut braced wing

The advantages of replacing the conventional wing on a transatlantic business jet with a larger, strut braced wing of aspect ratio 25 were evaluated. The lifting struts reduce both the induced drag and structural weight of the heavier, high aspect ratio wing. Compared to the conventional airplane, the strut braced wing design offers significantly higher lift to drag ratios achieved at higher lift coefficients and, consequently, a combination of lower speeds and higher altitudes. The strut braced wing airplane provides fuel savings with an attendant increase in construction costs.

Turriziani, R. V.↗

A study of high-altitude manned research aircraft employing strut-braced wings of high-aspect-ratio

The effect of increased wing aspect ratio of subsonic aircraft on configurations with and without strut bracing. Results indicate that an optimum cantilever configuration, with a wing aspect ratio of approximately 26, has a 19% improvement in cruise range when compared to a baseline concept with a wing aspect ratio of approximately 10. An optimum strut braced configuration, with a wing aspect ratio of approximately 28, has a 31% improvment in cruise range when compared to the same baseline concept. This improvement is mainly due to the estimated reduction in wing weight resulting from use of lifting struts. All configurations assume the same mission payload and fuel. The drag characteristics of the wings are enhanced with the use of laminar flow airfoils. A method for determining the extent of attainable natural laminar flow, and methods for preliminary structural design and for aerodynamic analysis of wings lifting struts are presented.

Smith, P. M.↗

Tone generation by rotor-downstream strut interaction

A JT15D fan stage was acoustically tested in the NASA Lewis anechoic chamber as part of the joint Lewis-Langley Research Center investigation of flight simulation techniques and flight effects using the JT15D engine as a common test vehicle. Suspected rotor-downstream support strut interaction was confirmed through the use of simulated support struts which were tested at three axial rotor-strut spacings. Tests were also performed with the struts removed. Inlet boundary layer suction in conjuction with an inflow control device was also explored. The removal of the boundary layer reduced the fan fundamental tone levels suggesting that the mounting and mating of such a device to the nacelle requires careful attention. With the same inflow control device installed good acoustic agreement was shown between the engine on an outdoor test stand and the fan in the anechoic chamber.

Woodward, R. P.↗

Tone generation by rotor-downstream strut interaction

A JT15D fan stage was acoustically tested in the NASA Lewis anechoic chamber as part of the joint Lewis-Langley Research Center investigation of flight simulation techniques and flight effects using the JT15D engine as a common test vehicle. Suspected rotor-downstream support strut interaction was confirmed through the use of simulated support struts which were tested at three axial rotor-strut spacings. Tests were also performed with the struts removed. Inlet boundary layer suction in conjunction with an inflow control device was also explored. The removal of the boundary layer reduced the fan fundamental tone levels suggesting that the mounting and mating of such a device to the nacelle requires careful attention. With the same inflow control device installed good acoustic agreement was shown between the engine on an outdoor test stand and the fan in the anechoic chamber.

Woodward, R. P.↗

Passive Orbital Disconnect Strut (PODS 3) structural test program

A passive orbital disconnect strut (PODS-3) was analyzed structurally and thermally. Development tests on a graphite/epoxy orbit tube and S glass epoxy launch tube provided the needed data to finalize the design. A detailed assembly procedure was prepared. One strut was fabricated. Shorting loads in both the axial and lateral direction (vs. load angle and location) were measured. The strut was taken to design limit loads at both ambient and 78 K (cold end only). One million fatigue cycles were performed at predicted STS loads (half in tension, half in compression) with the cold end at 78 K. The fatigue test was repeated at design limit loads. Six struts were then fabricated and tested as a system. Axial loads, side loads, and simulated asymmetric loads due to temperature gradients around the vacuum shell were applied. Shorting loads were measured for all tests.

Parmley, R. T.↗

Development of Space Station strut design

Candidate Space Station struts exhibiting high stiffness (38-40 msi modulus of elasticity) were manufactured and experimentally evaluated. One and two inch diameter aluminum-clad evaluation specimens were manufactured using a unique dry fiber resin injection process. Preliminary tests were performed on strut elements having 80 percent high-modulus graphite epoxy and 20 percent aluminum. Performed tests included modulus of elasticity, thermal cycling, and coefficient of thermal expansion. The paper describes the design approach, including an analytical assessment of strut thermal deformation behavior. The major thrust of this paper is the manufacturing process which produces aluminum-clad struts with precisely controlled properties which can be fine-tuned after fabrication. An impact test and evaluation procedure for evaluating toughness is described.

Johnson, R. R.↗

Experimental investigation of flow about a strut-endwall configuration

An experimental study was conducted to investigate incompressible flow about a strut-endwall configuration positioned within a constant area duct. The endwal boundary layer was tripped, but natural transition occurred on the strut surface. The results indicate that spanwise varying transition on this surface leads to the formation of a secondary vortex which coexists with the horseshoe vortex generated by endwall flow separation upstream of the strut leading edge. Both vortices are similar in strength downstream of the strut trailing edge, and both distort the primary flow and local turbulence structure in the wake-endwall region. The level of distortion is demonstrated by means of axial mean velocity contours, turbulence kinetic energy contours, and Reynolds shear stress contours measured in the cross plane at two streamwise locations. Analysis of the results shows that conventional eddy viscosity and k-epsilon transport equation models are not wholly adequate for predicting this flow situation.

Chang, P. S.↗

Design of a D-Strut and its application results in the JPL, MIT, and LaRC test beds

High damping at very low magnitudes of vibration is provided by an 'Arched Flexure' D-Strut. Five of these devices have been incorporated in JPL's CSI truss structure, and five more in MIT's interferometer test bed. Two were also temporarily installed in the LaRC CSI test structure. Damping factors in the 50 percent category are being provided at vibration motions as small as 50 nm. The 'Arched Flexure' used in the D-Strut maximizes the volumetric stiffness parameter relative to its axial stiffness. In turn, this enables high damping factors, even in a very rigid truss structure. This paper includes a presentation and discussion of both element and system test data taken at JPL, LaRC, and MIT. Also provided is a detailed description of the D-Strut, the dynamic model, and several graphs showing design parameter variations that will make it possible to evaluate the D-Strut for other applications.

Davis, L. P.↗

A variable stiffness strut using strain induced bending for vibration suppression in the evolutionary model

A new piezoceramic strut has been developed. This strut utilizes strain induced bending as a means of actuation. The significance of this design is that the displacement of the strut's motion arm is independent of the expansion of the piezoceramic material. Design criteria was developed using continuous and finite element modeling techniques. Experimental and analytical results were compared. Finally, a numerical analysis was conducted that demonstrated the benefits of the piezoceramic strut configuration.

Pokines, Brett↗

Composite passive damping struts for large precision structures

In the field of viscoelastic dampers, a new strut design comprises a viscoelastic material sandwiched between multiple layers, some of which layers bear and dampen load force. In one embodiment, the layers are composite plies of opposing orientation. In another embodiment, the strut utilizes a viscoelastic layer sandwiched between V-shaped composite plies. In a third embodiment, a viscoelastic layer is sandwiched between sine-shaped plies. Strut strength is equal to or greater than conventional aluminum struts due to the unique high interlaminar shear ply design.

Dolgin, Benjamin P.↗

Wind tunnel tests of five strut sections in yaw

In the first series of wind tunnel tests, the drag and cross wing force of all the struts were measured at a wind speed of 30 mph and at angles of yaw from 0 degrees to 20 degrees. To determine the magnitude of the VL effect, each strut was tested at zero yaw and at a series of speeds ranging from 15 to 38 mph. Although designed as fairings for cables, part of these sections gave such high crosswind forces that they seemed to have possibilities as airfoils. Therefore, the lift (identical with the crosswind force) and drag coefficients were recalculated for four sections on the basis of broadside area to make them comparable with wing coefficients. The general conclusion that the best fineness ratio for a strut is a function of the Reynolds number, decreasing steadily as that quality increases, has of course been reached many times, both by theory and experiment. It was confirmed here once more, and the effect of form on sensitiveness to VL is also strikingly shown. It seems probable that this effect of form is largely due to interaction between the nose and tail, and to the influence which the form of the nose exerts over the whole flow around the strut.

PROPELLERS, METAL↗

Interference Effects and Drag of Struts on a Monoplane Wing

Tests were conducted in the Variable Density Wind Tunnel of the NACA to determine the importance of the interference effects and drag of struts on a monoplane. Inclined struts were placed upon a Gottingen 387 airfoil in the lower surface positions and in two upper surface positions. Tests were made at values of Reynolds Number comparable with those obtained in flight. It was found that the interference drag of struts may be as great as the drag of the struts alone.

Ward, Kenneth E↗

Aerodynamic Theory and Tests of Strut Forms-II

This report presents the second of two studies under the same title. In this part five theoretical struts are developed from distributed sources and sinks and constructed for pressure and resistance tests in a wind tunnel. The surface pressures for symmetrical inviscid flow are computed for each strut from theory and compared with those found by experiment. The theoretical and experimental pressures are found to agree quantitatively near the bow, only qualitatively over the suction range, the experimental suctions being uniformly a little low, and not at all near the stern. This study is the strut sequel to Fuhrmann's research on airship forms, the one being a study in two dimensions, the other in three. A comparison of results indicates that the agreement between theory and experiment is somewhat better for bodies of revolution than for cylinders when both are shaped for slight resistance. The consistent deficiency of the experimental suctions which is found in the case of struts was not found in the case of airships, for which the experimental suctions were sometimes above sometimes below their theoretical values.

Smith, R H↗