Search NASA⌕ Search

SEARCH · Search NASA

Results for “Substrate effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The effect of substrate temperature on the critical velocity in microparticle impact bonding

A number of nascent coating and micromanufacturing processes involve particles sprayed at a high velocity, which impact a substrate, deform, and adhere. Successful bonding between the particles and the substrate requires impact velocities higher than the so-called critical adhesion velocity. This critical velocity is influenced by the temperature of the substrate, a variable that we isolate in this work by conducting single-particle impacts on a variable-temperature substrate for three systems (Al–Al, Sn–Sn, and Ti–Ti) with particles individually selected within a narrow size distribution. Our results quantitatively connect the increase in substrate temperature to a significant lowering of the critical velocity, which we attribute to the lower dynamic strength of the thermally softened substrate. The data are generally consistent with expectations for bonding being controlled by a hydrodynamic process of jetting upon impact.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of substrate temperature on sputter-deposited boron carbide films

Sputter deposition of B4C films with tailored physical properties remains a challenge. Here, we systematically study how substrate temperature influences the properties of B4C films deposited by direct current magnetron sputtering onto planar substrates held at temperatures in the range of 100-510°C. Results show that all films are amorphous stoichiometric B4C, with low O content of ~1 at. %. Films deposited onto substrates at 100°C exhibit high compressive residual stress and decreased mechanical properties. Therefore, for elevated substrate temperatures in the range of 180-510°C, film mass density, surface roughness, Young’s modulus, and hardness are weakly dependent on substrate temperature. However, in this temperature range, an increase in substrate temperature leads to larger residual compressive stress accompanied by a corresponding reduction in the concentration of nanoscale inhomogeneities. At least for the landing atom ballistics conditions studied here, a substrate temperature range of ~185-250°C is optimum for growing films with near-zero intrinsic residual stress. The overall weak substrate temperature dependence of film properties revealed in this work is favorable for the development of a robust deposition process, particularly for the case of deposition onto non-planar substrates where temperature control is often challenging.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of substrate and growth method on vanadium dioxide thin films by RF magnetron sputtering: Vanadium metal oxidation vs reactive sputtering

Vanadium dioxide (VO 2 ) undergoes a metal–insulator phase transition at ~70 °C and has attracted substantial interest for potential applications in electronics, including those in neuromorphic computing. The vanadium–oxygen system has a rather complicated phase diagram, and controlling the stoichiometry and the phase of thin films of vanadium oxides is a well-known challenge. Here, we explore the novel combination of two methods of VO 2 thin film deposition using off-axis RF magnetron sputtering on (100)- and (111)-oriented yttria-stabilized zirconia (YSZ) substrates: reactive sputtering of vanadium in an oxygen environment and sputtering of vanadium metal followed by oxidation to VO 2 . Interestingly, the reactive sputtering process on both substrate orientations yields the metastable semiconducting VO 2 (B) phase, which is structurally stabilized by the YSZ surface. The metal sputtering and oxidation process on YSZ produces mainly the equilibrium monoclinic (or M1) phase of VO 2 that exhibits a metal–insulator transition. Using this method, we obtained thin films of (010)-textured polycrystalline VO 2 (M1) that show a metal–insulator transition with an on/off ratio larger than 1000.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Substrate Temperature on the Electrochemical and Supercapacitance Properties of Pulsed Laser-Deposited Titanium Oxynitride Thin Films

Electrocatalytically active titanium oxynitride (TiNO) thin films were fabricated on commercially available titanium metal plates using a pulsed laser deposition method for energy storage applications. The elemental composition and nature of bonding were analyzed using X-ray photoelectron spectroscopy (XPS) to reveal the reacting species and active sites responsible for the enhanced electrochemical performance of the TiNO electrodes. Symmetric supercapacitor devices were fabricated using two TiNO working electrodes separated by an ion-transporting layer to analyze their real-time performance. The galvanostatic charge–discharge studies on the symmetric cell have indicated that TiNO films deposited on the polycrystalline titanium plates at lower temperatures are superior to TiNO films deposited at higher temperatures in terms of storage characteristics. For example, TiNO films deposited at 300 °C exhibited the highest specific capacity of 69 mF/cm 2 at 0.125 mA/cm 2 with an energy density of 7.5 Wh/cm 2 . The performance of this supercapacitor (300 °C TiNO) device is also found to be ~22% better compared to that of a 500 °C TiNO supercapacitor with a capacitance retention ability of 90% after 1000 cycles. Furthermore, the difference in the electrochemical storage and capacitance properties is attributed to the reduced leaching away of oxygen from the TiNO films by the Ti plate at lower deposition temperatures, leading to higher oxygen content in the TiNO films and, consequently, a high redox activity at the electrode/electrolyte interface.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1978

Lubrication and failure mechanisms of molybdenum disulfide films. 2: Effect of substrate roughness

An optical microscope was used to study the lubrication and failure mechanisms of rubbed MoS2 films applied to three substrate surface finishes; polished, sanded, and sandblasted as a function of sliding distance. The lubrication mechanism was the plastic flow of thin films of MoS2 between flat plateaus on the rider and on the metallic substrate. If the substrate was rough, flat plateaus were created during run-in and the MoS2 flowed across them. Wear life was extended by increasing surface roughness since valleys in the roughened substrate served as reservoirs for MoS2 and as deposit sites for wear debris. In moist air the failure mechanism was the transformation of metallic colored MoS2 films to a black, powdery material that was found by X-ray diffraction to be alpha iron, MoO3, and possibly FeMoO3. In dry argon the failure mechanism was the gradual depletion of MoS2 from the contact region by transverse flow, and the wear debris on the track at failure was alpha iron, residual MoS2, and possibly FeS.

Fusaro, R. L.↗
NASA NTRS1980

Effect of Substrate Surface Finish on the Lubrication and Failure Mechanisms of Molybdenum Disulfide Films

An optical microscope was used to study the lubrication and failure mechanisms of rubbed (burnished) MoS2 films applied to three substrate surface finishes - polished, sanded, and sandblasted - as a function of sliding distance. The lubrication mechanism was the plastic flow of thin films of MoS2 between flat plateaus on the rider and on the metallic substrate. If the substrates were rough, flat plateaus were created during 'run in' and the MoS2 flowed across them. Wear life was extended by increasing surface roughness since valleys in the roughened substrate served as reservoirs for MoS2 and a deposit site for wear debris. In moist air, the failure mechanism was the transformation of metallic colored MoS2 films to a black, powdery material that was found by X ray diffraction to consist primarily of alpha iron and MoO3 powders. In dry argon, the failure mechanism was the gradual depletion of the MoS2 film from the contact region by transverse flow. Analysis of the wear debris on the wear track at failure showed it consisted mainly of alpha iron and some residual MoS2. No molybdenum oxides were found.

Fusaro, R. L.↗
NASA NTRS1981

Effect of substrate surface finish on the lubrication and failure mechanisms of molybdenum disulfide films

An optical microscope was used to study the lubrication and failure mechanisms of rubbed (burnished) MoS2 films applied to three substrate surface finishes - polished, sanded, and sandblasted - as a function of sliding distance. The lubrication mechanism was the plastic flow of thin films of MoS2 between flat plateaus on the rider and on the metallic substrate. If the substrate was rough, flat plateaus were created during 'run-in' and the MoS2 flowed across them. Wear life was extended by increasing surface roughness since valleys in the roughened substrate served as reservoirs for MoS2 and a deposit site for wear debris. In moist air, the failure mechanism was the transformation of metallic-colored MoS2 films to a black, powdery material that was found by X-ray diffraction to consist primarily of alpha-iron and MoO3 powders. In dry argon, the failure mechanism was the gradual depletion of the MoS2 film from the contact region by transverse flow. Analysis of the wear debris on the wear track at failure showed it consisted mainly of alpha-iron and some residual MoS2. No molybdenum oxides were found.

Fusaro, R. L.↗
NASA NTRS1988

Effect of substrate preparation on the structure and chemisorption properties of Pd/MgO model catalyst

Pd/MgO model catalysts are prepared by vapor deposition of Pd particles on MgO thin films which are deposited, at different temperatures, on UHV cleaved mica. MgO films and Pd particles are characterized in situ by Auger electron spectroscopy and energy-loss spectroscopy and ex situ by transmission electron microscopy. Succesive temperature programmed desorption (TPD) of CO shows a different evolution of the morphology of the Pd particles deposited on MgO films prepared at low and high temperature. In addition, on MgO prepared at low temperature, the smallest particles show a continuous decay of CO adsorption during TPD due to contamination by support species.

Henry, C. R.↗
NASA NTRS1999

Polarity Effects of Substrate Surface in Epitaxial ZnO Film Growth

Epitaxial ZnO films were grown on the two polar surfaces (0-face and Zn-face) of (0001) ZnO single crystal substrates using off-axis magnetron sputtering deposition. As a comparison, films are also deposited on the (000 I) Al203 substrates. It is found that the two polar surfaces have different photoluminescence (PL) spectrum, surface structure and morphology, which are strongly inference the epitaxial film growth. The morphology and structure of epitaxial films on the ZnO substrates are different from the film on the Al203 substrates. An interesting result shows that high temperature annealing of ZnO single crystals will improve the surface structure on the O-face surface rather than the opposite Surface. The measurements of PL, low-angle incident x-ray diffraction, and atomic force microscopy of ZnO films indicate that the O-terminated surface is better for ZnO epitaxial film growth using reactive sputtering deposition.

Zhu, Shen↗
DOE OSTI2021

Effect of substrate temperature on the growth of Nb$_3$Sn film on Nb by multilayer sputtering

Nb3Sn films were fabricated by multilayer sequential sputtering on Nb substrates at substrate temperatures ranging from room temperature to 250 °C. The film material properties were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, atomic force microscopy, and transmission electron microscopy. The films’ superconducting properties were studied by four-point probe resistivity measurements from room temperature to below the superconducting critical temperature Tc. The highest Tc was17.76 K, when the multilayers were deposited at room temperature. A superconducting Nb3Sn thin film with a smoother surface morphology but a lower Tc of 17.58 K was obtained on the film deposited at a substrate temperature of 250 °C.

Sayeed, Md. Nizam↗
NASA NTRS1994

Holt film wall shear instrumentation for boundary layer transition research

Measurements of the performance of hot-film wall-shear sensors were performed to aid development of improved sensors. The effect of film size and substrate properties on the sensor performance was quantified through parametric studies carried out both electronically and in a shock tube. The results show that sensor frequency response increases with decreasing sensor size, while at the same time sensitivity decreases. Substrate effects were also studied, through parametric variation of thermal conductivity and heat capacity. Early studies used complex dual-layer substrates, while later studies were designed for both single-layer and dual-layer substrates. Sensor failures and funding limitations have precluded completion of the substrate thermal-property tests.

Schneider, Steven P.↗
DOE OSTI2020

Density Functional Theory Study of the Adsorption and Dissociation of Copper(I) Acetamidinates on Ni(110): The Effect of the Substrate

In order to assess the role of a metal substrates on the thermal chemistry of adsorbed acetamidinate metalorganic compounds, we have studied the surface chemistry of copper(I)–N,N'-dimethylacetamidinate on Ni(110) using density functional theory and contrasted it with similar calculations we previously carried out on Cu(110). At low coverages, it was found that, in its most stable configuration, the molecular adsorption of copper(I)–N,N'-dimethylacetamidinate dimers occurs with the Cu atoms occupying surface hollow sites. In this work, the ligands reorient away from those metal centers, and the N atoms develop new direct bonds with surface Ni atoms. However, this configuration is not stable and decomposes by losing both ligands to the surface. In the final state, the two ligands bind via their N atoms to Ni sites one lattice space away from the sites where the Cu atoms remain, with their molecular planes perpendicular to that of the surface. This is in contrast with what happens in the case of adsorption on Cu(110), where the Cu atoms from the metalorganic complex still occupy hollow sites but where only one of the ligands breaks away and binds directly to the surface; the other remains on top of the two Cu ions. In terms of the energetics of adsorption and decomposition, the reactions on Ni(110) are much more exothermic than on Cu(110). Further analysis of the distribution of charge within the adsorbates shows a minor reduction of the Cu atoms of the dimer upon interaction with the surface; full reduction to metallic copper is complete only when both ligands have fully migrated to their new Ni surface sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1987

Model of hot-film sensor with substrate

A detailed model is constructed to investigate parameters influencing a hot-film anemometer system used to study cross-flow phenomena on swept wings. This anemometer is designed to detect vortices set up by cross-flow. The nature of the vortices is not well known, and a well-verified instrumentation model is considered essential to allow accurate interpretation of experimental results. Previous investigators have indicated that heat conduction to the film's substrate is significant. Two variations on the inclusion of substrate effects in the model are discussed. In the first, the substrate is assumed to have a constant temperature throughput: in the second more elaborate model, the temperature of the substrate is allowed to vary. This variation is related to the convective heat removal at the substrate/gas interface.

Mcree, Griffith J.↗
DOE OSTI2025

Conversion of Polystyrene to Terephthalic Acid via Sequential Acetylation and Mn/Br-Catalyzed Autoxidation

Most methods for the oxidative deconstruction of polystyrene produce benzoic acid, which has a low market size relative to the production of waste polystyrene. Here, the present study demonstrates a method for conversion of polystyrene into terephthalic acid, a high-volume chemical, by introducing a carbon-containing fragment into the para position of the phenyl groups in polystyrene, followed by Mn/Br-catalyzed autoxidation. Acetylated polystyrene is shown to be the most effective substrate for oxidation, affording an 81% yield of terephthalic acid. Mechanistic studies highlight the effectiveness of bromide as a cocatalyst and offer insight into the underlying reasons the acetyl group undergoes efficient oxidation.

Mid-Century Process↗
DOE OSTI2022

Effect of metal/dielectric substrates on photopolymerization of BITh thin films

Abstract We have studied effects of metal–dielectric substrates on photopolymerization of [2,2ʹ-Bi-1H-indene]-1,1ʹ-dione-3,3ʹ-diyl diheptanoate (BITh) monomer. We synthetized BITh and spin-coated it onto a variety of dielectric, metallic, and metal–dielectric substrates. The films were exposed to radiation of a UV–Visible Xe lamp, causing photo-polymerization of monomer molecules. The magnitude and the rate of the photo-polymerization were monitored by measuring the strength of the ~ 480 nm absorption band, which existed in the monomer but not in the polymer. Expectedly, the rate of photo-polymerization changed nearly linearly with the change of the pumping intensity. In contrast with our early study of photo-degradation of semiconducting polymer P3HT, the rate of photo-polymerization of BITh is getting modestly higher if the monomer film is deposited on top of silver separated from the monomer by a thin insulating MgF 2 layer preventing a charge transfer. This effect is partly due to a constructive interference of the incident and reflected light waves, as well as known in the literature effects of metal/dielectric substrates on a variety of spectroscopic and energy transfer parameters. At the same time, the rate of photopolymerization is getting threefold larger if monomer is deposited on Ag film directly and charge transfer is allowed. Finally, Au substrates cause modest (~ 50%) enhancement of both monomer film absorption and the rate of photo-polymerization.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Factors modulating the hydrolysis of Nylon-6,6 by a nylon hydrolase enzyme

The enzymatic hydrolysis of polyamides offers a promising approach to reduce the environmental impact of chemical recycling by enabling lower reaction temperatures, eliminating toxic organic solvents, and enhancing product selectivity. Achieving this goal will require increasing the low overall yield of enzymatic hydrolysis. In this work, we studied the mechanism of hydrolysis of commercial Nylon-6,6 polymer with a thermostable Nylon hydrolyzing enzyme and identified the substrate characteristics that influence the efficiency and deconstruction product yield. These results will guide the development of effective substrate pre-treatment methods to improve the yield of valuable oligoamide building blocks via enzymatic hydrolysis.

Bocharova, Vera [Oak Ridge National Laboratory (OR↗