Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Surface effects on deuterium permeation through vanadium membranes

Dense vanadium-based membranes offer high permeability and perfect selectivity to hydrogen isotopes, maintain favorable neutronic properties, and are compatible with liquid metals such as PbLi. These properties make vanadium membranes a promising fusion fuel cycle technology for processes such as tritium extraction from PbLi and exhaust processing. Surface contamination has a deleterious effect on the gas-phase hydrogen permeation through vanadium, and the reported permeabilities range from 10 -14 to 10 -7 mol m -1 s -1 Pa -0.5 . Thin dense films of palladium applied to clean vanadium surfaces enable a consistently high hydrogen permeability. In this study, uncoated vanadium resulted in deuterium permeabilities ranging from 2.8 × 10 -11 to 6.4 × 10 -9 mol m -1 s -1 Pa -0.5 at 300 °C–700 °C, respectively. Post-test analysis revealed a VO x surface layer and VC x subsurface layer formed on the feed side, while the as-received surface oxide dissolved leaving a submonolayer oxide on the permeate surface. Furthermore, the Pd-coated V resulted in a maximum deuterium permeability of 2.1 × 10 -7 m -1 s -1 Pa -0.5 at 375 °C upon activation of the Pd surface by oxidation and reduction. The deuterium permeation declined upon heating to 500 °C due to intermetallic diffusion between the Pd and V. The Mo 2 C-coated V resulted in deuterium permeabilities ranging from 2.7 × 10 -10 to 1.8 × 10-9 at 500 °C–700 °C, respectively, and a post-test analysis found the carbon in the Mo 2 C layer had dissolved into the V near the interface.

13 HYDRO ENERGY↗
NASA NTRSDate not supplied

Evaluation of CFD for Simulation of High-Supersonic Control Surface Effectiveness

This is the set of slides describing the CFD and wind-tunnel test studying the control surfaces of the CobraMRV concept for entry, descent, and landing on Mars. Difference between the CFD and wind-tunnel results are highlighted with the intent of showing whether CFD can replace wind-tunnel testing in the high supersonic flight regime.

wind tunnel↗
DOE OSTI2024

Concurrent Amorphization and Nanocatalyst Formation in Cu‐Substituted Perovskite Oxide Surface: Effects on Oxygen Reduction Reaction at Elevated Temperatures

Abstract The activity and durability of chemical/electrochemical catalysts are significantly influenced by their surface environments, highlighting the importance of thoroughly examining the catalyst surface. Here, Cu‐substituted La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3‐δ is selected, a state‐of‐the‐art material for oxygen reduction reaction (ORR), to explore the real‐time evolution of surface morphology and chemistry under a reducing atmosphere at elevated temperatures. Remarkably, in a pioneering observation, it is discovered that the perovskite surface starts to amorphize at an unusually low temperature of approximately 100 °C and multicomponent metal nanocatalysts additionally form on the amorphous surface as the temperature raises to 400 °C. Moreover, this investigation into the stability of the resulting amorphous layer under oxidizing conditions reveals that the amorphous structure can withstand a high‐temperature oxidizing atmosphere (≥650 °C) only when it has undergone sufficient reduction for an extended period. Therefore, the coexistence of the active nanocatalysts and defective amorphous surface leads to a nearly 100% enhancement in the electrode resistance for the ORR over 200 h without significant degradation. These observations provide a new catalytic design strategy for using redox‐dynamic perovskite oxide host materials.

Jeon, SungHyun↗
NASA NTRS1980

Surface effects on the microwave backscatter and emission of snow

Measurements were performed with active and passive microwave sensors for both dry and wet snow conditions. A layer of Rayleigh scatterers with irregular surface boundaries is found to be a reasonable model for interpreting passive and active measurements in X- and Ku-bands. It was found that roughness had a significant effect on both backscatter and emission from wet snow; however, only a small effect was noted for dry snow.

Fung, A. K.↗
NASA NTRS1984

Real Surface Effects in Elastohydrodynamic Lubrication

Following a general discussion of real effects in EHL, consideration is given in detail to the role played by stochastic roughness superimposed on the nominal solid boundaries. Particular attention is given to the full-film EHL regime where incipient asperity contact bears a negligible fraction of the load. Flow, from which an averaged Reynolds equation can be formed, is nonetheless modified by the amplitude and texture of the roughness patterns. In describing these effects by means of certain well-defined flow factors, it is found that only two extra parameters are needed - the rms surface height and the ratio of the correlation lengths in the two principal roughness directions. In a lowest order perturbation expansion of these flow factors in powers of the ratio of rms roughness to nominal film thickness, no other properties of the roughness appear. In most cases of practical interest, the factors describing Poiseuille flow are separable into the sum of two single-surface flow factors which means that a combination of a single equivalent rough surface versus an ideal smooth surface can always be found. For flow entrained by slip velocity the factors separate instead into a difference of single-surface factors and it becomes significant which of the two surfaces carries the equivalent roughness. Results are discussed of some applications of the averaged Reynolds equation based on the flow factor method to the EHL line contact problem. Finally, the partial EHL regime is considered where comparable load fractions are carried by the hydrodynamic film and by incipient mechanical contact. An extension of the method into this regime by combining it with asperity contact models appears most encouraging.

John H Tripp↗
DOE OSTI2020

Surface Effects on Pyrene Luminescence Excitation

Pyrene is a polycyclic aromatic hydrocarbon with fluorescence in the 370-400 nm range. The optical properties of pyrene deposited on different substrates were investigated from experimental and theoretical points of view. In contrast to prior studies of surface-enhanced fluorescence, in this work all substrates were semiconductors or insulators. Experimentally, the intensity of photoluminescence (PL) and PL excitation (PLE) spectra were investigated. PLE spectra of pyrene’s monomer emission show that the intensities of the two main absorption peaks vary according to the chosen substrate. Here, calculations for pyrene on zinc sulfide (ZnS) and surface-oxidized diamond suggest that this connection arises from the alignment of the pyrene electronic levels relative to the band edges of the substrate. The absorption peak at 272 nm (4.56 eV) is shown to depend on the HOMO-1→LUMO orbital contribution while the 335 nm (3.70 eV) peak depends upon the HOMO→LUMO transition. When the HOMO-1 level falls inside the substrate valence band, as in the case of ZnS, there is significant hybridization of the molecular state with surface states that causes an enhancement of the 272 nm peak. For pyrene on diamond, however, the HOMO-1 level falls in the substrate bandgap, leading to negligible hybridization and thus no enhancement.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1986

Surface effects on phase distributions of a fast-quenched miscibility gap type system - Succinonitrile-water

If a binary homogeneous melt is cooled into an immiscible region, the newly formed second phase will generally have a density different from the parent phase, and will separate readily by sedimentation. Observation of solidification processes in microgravity indicates that outside of sedimentation, at least two other important effets can separate the phases: (1) preferential wetting, and (2) thermal migration of second-phase droplets due to interfacial tension gradients. The latter effect would drive the minority phase along the thermal gradient toward the hottest part (assuming the interfacial tension decreases with increasing temperature), which is usually away from the crucible wall. On the other hand, if the minority phase preferentially wets the crucible, a minority phase layer which thickens as initial solution compositions approach critical, will form adjacent to the solid surface and remain in the coldest region of the ingot. This study presents compelling preliminary evidence that these two effects do exist and that they compete with one another. However, the temperature dependence of preferential wetting below T(c) for the current system of study is, as yet, undetermined. These effects are sensitive to the initial concentration of a hypermonotectic solution cooling through a miscibility gap.

Frazier, D. O.↗
NASA NTRS1985

Surface effects of corrosive media on hardness, friction, and wear of materials

Hardness, friction, and wear experiments were conducted with magnesium oxide exposed to various corrosive media and also with elemental iron and nickel exposed to water and NaOH. Chlorides such as MgCl2 and sodium containing films were formed on cleaved magnesium oxide surfaces. The MgCl2 films softened the magnesium oxide surfaces and caused high friction and great deformation. Hardness was strongly influenced by the pH value of the HCl-containing solution. The lower the pH, the lower the microhardness. Neither the pH value of nor the immersion time in NaOH containing, NaCl containing, and HNO3 containing solutions influenced the microhardness of magnesium oxide. NaOH formed a protective and low friction film on iron surfaces. The coefficient of friction and the wear for iron were low at concentrations of NaOH higher than 0.01 N. An increase in NaOH concentration resulted in a decrease in the concentration of ferric oxide on the iron surface. It took less NaOH to form a protective, low friction film on nickel than on iron.

Miyoshi, K.↗
NASA NTRS1985

Surface effects of corrosive media on hardness, friction, and wear of materials

Hardness, friction, and wear experiments were conducted with magnesium oxide exposed to various corrosive media and also with elemental iron and nickel exposed to water and NaOH. Chlorides such as MgCl2 and sodium containing films were formed on cleaved magnesium oxide surfaces. The MgCl2 films softened the magnesium oxide surfaces and caused high friction and great deformation. Hardness was strongly influenced by the pH value of the HCl-containing solution. The lower the pH, the lower the microhardness. Neither the pH value of nor the immersion time in NaOH containing, NaCl containing, and HNO3 containing solutions influenced the microhardness of magnesium oxide. NaOH formed a protective and low friction film on iron surfaces. The coefficient of friction and the wear for iron were low at concentrations of NaOH higher than 0.01 N. An increase in NaOH concentration resulted in a decrease in the concentration of ferric oxide on the iron surface. It took less NaOH to form a protective, low friction film on nickel than on iron.

Miyoshi, K.↗
DOE OSTI2024

Untangling charge-order dependent bulk states from surface effects in a topological kagome metal ScV 6 Sn 6

Kagome metals with charge density wave (CDW) order exhibit a broad spectrum of intriguing quantum phenomena. The recent discovery of the novel kagome CDW compound ScV 6 Sn 6 has spurred significant interest. However, understanding the interplay between CDW and the bulk electronic structure has been obscured by a profusion of surface states and terminations in this quantum material. Here, in this study, we employ photoemission spectroscopy and potassium dosing to elucidate the complete bulk band structure of ScV 6 Sn 6 , revealing multiple van Hove singularities near the Fermi level. We surprisingly discover a robust spin-polarized topological Dirac surface resonance state at the M point within the twofold van Hove singularities. Assisted by first-principles calculations, the temperature dependence of the k z -resolved angle-resolved photoemission spectroscopy spectrum provides unequivocal evidence for the proposed $\sqrt{3}$×$\sqrt{3}$×3 charge order over other candidates. Our work not only enhances the understanding of the CDW-dependent bulk and surface states in ScV 6 Sn 6 , but also establishes an essential foundation for potential manipulation of the CDW order in kagome materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The Ductility of 49Fe-49Co-2V Soft Magnetic Alloy Bar: Surface Effects and Test Methods

The tensile ductility of 49Fe-49Co-2V (Hiperco® 50A) bar was investigated in both as-received and heat-treated conditions. The as-received/machined specimens exhibit very low ductility compared to samples where heat treatment was the final step prior to testing. Microstructural characterization showed that internal residual strain from bar processing and, most importantly, surface machining damage, cause lower elongation in the as-received material. Because fracture of this intermetallic alloy initiates at the surface, it is particularly susceptible to surface machining damage, i.e., the near-surface region has already exhausted most of its ability to accumulate tensile strain. During heat treatment, the internal residual strain and near-surface machining damage are eliminated and ductility is improved, despite a higher degree of crystallographic ordering in the heat-treated condition (which typically lowers ductility). Furthermore, if machining is again performed after heat treatment, the material again exhibits brittle behavior, even with only light touch-up machining passes. Here, in this work, methods of tensile strain measurement were investigated, namely conventional knife-edge extensometry and noncontact digital image correlation (DIC) on heat-treated material. For clip-on knife-edge extensometry, the range of failure strain was 2.5-5.5% for heat-treated Hiperco. For noncontact methods, ductility up to 7% was observed. The results highlight the tendency for the alloy to fail at surface imperfections, even those produced by application of the extensometer itself. Noncontact laser extensometry is recommended for determining the intrinsic ductility of the alloy. A method of laser surface modification was developed which increased ductility by ~ 100% compared to unmodified samples. The high cooling rates achieved during laser surface processing can bypass the ordering reaction and produce a ductile disordered structure at the surface that exhibits ductile fracture characteristics.

EBSD↗
NASA NTRS1982

Strong refraction near the Venus surface - Effects observed by descent probes

The telemetry signals from Pioneer Venus probes indicated the strong downward refraction of radio waves. As the probes descended, the strength of the direct signal decreased because of absorption and refractive defocusing. During the last 30 km of descent there was a second measured component in addition to the direct signal. Strong atmospheric reaction is important in strengthening echoes that are scattered toward the earth. Such surface-reflected signals are good indicators of horizontal winds.

Croft, T. A.↗
DOE OSTI2026

Urban Land Surface Effects on Summertime Clouds and Moist Convection in Houston Under Different Synoptic Conditions

Urban landscapes modify cloud formation and convection through complex thermodynamic and aerodynamic processes; however, their influence under different synoptic regimes remains poorly understood. This study investigates the impact of the Houston metropolitan area on summertime cloud cover and convective cell characteristics using a combination of satellite observations, radar data, and high-resolution process-based modeling. We isolate urban effects by comparing model simulations with realistic urban land cover against hypothetical scenarios where all urban areas are replaced by rural vegetation. Results reveal that Houston's land cover consistently enhances cloud fraction and convective activity relative to surrounding rural areas, altered by large-scale meteorological forcing. Under weakly forced conditions, enhanced surface heat flux primarily contributes to driving low-level convergence and vertical ascent, leading to over 8% cloud fraction increase between 2 and 6 km over the city. Under strongly forced conditions, urban influences manifest differently depending on cloud type. For non-convective clouds, the city acts as a barrier that decelerates and lifts moist southerly inflow, increasing low cloud cover over the urban core, while decreasing it downwind the city. For convective clouds, both synoptic ascent and urbanization modulate moisture redistribution and cloud structure, producing modest cloud enhancement over the city and slight suppression over the downwind area. Urbanization exerts small changes in the intensity of the convective cells; however, it significantly decreases their duration and traveling distance. This work highlights the importance of accounting for land surface heterogeneity in modeling clouds and precipitation and demonstrates that urban impacts on clouds are highly regime-dependent.

Liu, Ye [Pacific Northwest National Laboratory (PN↗
NASA NTRSDate not supplied

Evaluation of CFD Predictions of CobraMRV Control Surface Effectiveness at the NASA Langley Unitary Plan Wind Tunnel

The ability of CFD simulations to serve as a surrogate for wind tunnel testing at high supersonic speeds has been evaluated for a sub-scale model of the Co-Optimization Blunt-body Re-entry Analysis-Mid-lift-to-drag Rigid Vehicle (CobraMRV) human Mars entry vehicle concept. The vehicle was tested at the Unitary Plan Wind Tunnel (UPWT) at the NASA Langley Research Center under flow conditions and surface control configurations relevant to the entry stage of a flight mission. The CFD simulations were performed prior to gaining access to test results in order to assess how blind predictions obtained using best practices compare to experiments. Solutions of empty tunnel simulations were used as inflow boundary condition for the CobraMRV simulations in a truncated portion of the test section. Different solvers and turbulence models were used by separate teams to assess sensitivity to numerical methods, physics, and users. After release of the test results, the pre-test computations were compared to the experimental results, and additional analyses have been conducted to explain observed discrepancies. The amount of time and resources dedicated to each phase of the computational work was logged for comparison to that required for wind tunnel tests, and to inform planning of future CFD data base development projects.

ARMD↗