Preliminary Investigation of the Effect of Fences and Balancing Tabs on the Hinge-moment Characteristics of a Tip Control on a 60 Degree Delta Wing at Mach Number 1.61
Explore the source record for details and available documents.
Czarnecki, K R↗
SEARCH · Search NASA
Results for “TAB EFFECT”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Film-Cooling Heat-Transfer Measurements Using Liquid Crystals
The following topics are discussed: (1) The Transient Liquid-Crystal Heat-Transfer Technique; (2) 2-D Film-Cooling Heat-Transfer on an AlliedSignal Vane; and (3) Effects of Tab Vortex Generators on Surface Heat Transfer. Downstream of a Jet in Crossflow.
Hippensteele, Steven A.↗
Supersonic Aerodynamic Characteristics of Blunt Body Trim Tab Configurations
Trim tabs are aerodynamic control surfaces that can allow an entry vehicle to meet aerodynamic performance requirements while reducing or eliminating the use of ballast mass and providing a capability to modulate the lift-to-drag ratio during entry. Force and moment data were obtained on 38 unique, blunt body trim tab configurations in the NASA Langley Research Center Unitary Plan Wind Tunnel. The data were used to parametrically assess the supersonic aerodynamic performance of trim tabs and to understand the influence of tab area, cant angle, and aspect ratio. Across the range of conditions tested (Mach numbers of 2.5, 3.5, and 4.5; angles of attack from -4deg to +20deg; angles of sideslip from 0deg to +8deg), the effects of varying tab area and tab cant angle were found to be much more significant than effects from varying tab aspect ratio. Aerodynamic characteristics exhibited variation with Mach number and forebody geometry over the range of conditions tested. Overall, the results demonstrate that trim tabs are a viable approach to satisfy aerodynamic performance requirements of blunt body entry vehicles with minimal ballast mass. For a 70deg sphere-cone, a tab with 3% area of the forebody and canted approximately 35deg with no ballast mass was found to give the same trim aerodynamics as a baseline model with ballast mass that was 5% of the total entry mass.
Korzun, Ashley M.↗
Flight Measurements to Determine Effect of a Spring-Loaded Tab on Longitudinal Stability of an Airplane
In conjunction with a program of research on the general problem of stability of airplanes in the climbing condition, tests have been made of a spring-loaded tb which. is referred to as a ?springy tab,? installed on the elevator of a low-wing scout bomber. The tab was arranged to deflect upward with decrease in speed which caused an increase in the pull force required to trim at low speeds and thereby increased the stick-free static longitudinal stability of the airplane. It was found that the springy tab would increase the stick-free stability in all flight conditions, would reduce the danger of inadvertent stalling because of the definite pull force required to stall the airplane with power on, would reduce the effect of center-of-gravity position on stick-free static stability, and would have little effect on the elevator stick forces in accelerated f11ght. Another advantage of the springy tab is that it might be used to provide almost any desired variation of elevator stick force with speed by adjusting the tab hinge-moment characteristics and the variation of spring moment with tab deflection. Unlike the bungee and the bobweight, the springy tab would provide stick-free static stability without requiring a pull force to hold the stick back while taxying. A device similar to the springy tab may be used on the rudder or ailerons to eliminate undesirable trim-force variations with speed.
TABS, ELEVATOR↗
Numerical Simulation of Mixing Enhancement in a Hot Supersonic Jet
Experimental observations show that the presence of small tabs on the edge of a hot, compressible jet exiting into a slower moving, colder ambient flow can increase the rate of spreading of the jet. This suggests that the rate of mixing of the jet and the ambient fluid is also increased. In order to elucidate the physical mechanism responsible for the increased spreading rate a set of calculations were carried out within the framework of the compressible three dimensional Navier-Stokes equations. A series of grid refinements were made to assess the accuracy of the results. The first simulated the flow without the tabs, obtaining reasonable agreement with experimental measurements of the velocity. We then simulated the flow, without tabs, over a range of values of the convective Mach number in order to determine the dependence of the mixing on this parameter. Simulations with modeled tabs were also carried out. In these calculations the effect of the tabs on the flow was modeled by pairs of counter rotating vortices. The results of these calculations indeed show that the presence of the tabs increase the spreading rate of the jet. The basic physical mechanism responsible for the enhanced spreading rate is discussed and qualitative comparisons with flow visualizations are made.
Grosch, C. E.↗
Effects of Elevator Nose Shape, Gap, Balance, and Tabs on the Aerodynamic Characteristics of a Horizontal Tail Surface
Results are presented showing the effects of gap, elevator, nose shape, balance, cut-out, and tabs on the aerodynamic characteristics of a horizontal tail surface tested in the NACA full-scale tunnel.
Goett, Harry J↗
The Effect of Vortex Generators on a Jet in a Cross-Flow
The effect of vortex generators in the form of tabs on the penetration and spreading of a jet in a cross-flow has been studied experimentally. It is found that the tab has very little effect when placed on the leeward side, i.e., on the downstream edge of the jet nozzle relative to the free-stream flow. A study of the static pressure distribution reveals significantly lower pressures on the leeward side. Thus, when placed on that side the tab does not produce a "pressure hill" of sufficient magnitude that is the primary source of streamwise vorticity in the flow field over the tab. This qualitatively explains the ineffectiveness. In comparison, there is a significant effect on the flow field when the tab is placed on the windward side, The sense of vorticity generated by the tab in the latter configuration is opposite to that of the bound vortex pair that otherwise characterizes the flow. Thus, the strength of the bound vortex pair is diminished and the jet penetration is reduced.
Zaman, K. B. M. Q.↗
Reduction of Jet Penetration in a Cross-Flow by Using Tabs
A tab placed suitably on a nozzle that produces a jet in a cross-flow can reduce the penetration of the jet. This effect, achieved when the tab is placed on the windward side of the nozzle relative to the cross flow, may be of interest in film cooling applications. Wind tunnel experiments are carried out, in the momentum ratio (J) range of 10-90, to investigate the tab geometry that would maximize this effect. The preliminary results show that a 'delta tab' having a base width approximately fifty percent of the nozzle diameter may be considered optimum. With a given tab size, the effect is more pronounced at higher J. Reduction in jet penetration by as much as 40% is observed. Comparable reduction in jet penetration is also obtained when a triangular shaped tab is placed flush with the tunnel wall or with its apex tilted down into the jet nozzle (the 'delta tab' being the configuration in which the apex is tilted up). However, the delta tab involves the least flow blockage and pressure loss. Relative to the baseline case, the lateral spreading of the jet is found to be more with the delta tab but less with other orientations of the tab.
Zaman, K. B. M. Q.↗
Experimental and Computational Investigation of Lift-Enhancing Tabs on a Multi-Element Airfoil
An experimental and computational investigation of the effect of lift-enhancing tabs on a two-element airfoil has been conducted. The objective of the study was to develop an understanding of the flow physics associated with lift-enhancing tabs on a multi-element airfoil. An NACA 63(2)-215 ModB airfoil with a 30% chord fowler flap was tested in the NASA Ames 7- by 10-Foot Wind Tunnel. Lift-enhancing tabs of various heights were tested on both the main element and the flap for a variety of flap riggings. A combination of tabs located at the main element and flap trailing edges increased the airfoil lift coefficient by 11% relative to the highest lift coefficient achieved by any baseline configuration at an angle of attack of 0 deg, and C(sub 1max) was increased by 3%. Computations of the flow over the two-element airfoil were performed using the two-dimensional incompressible Navier-Stokes code INS2D-UP. The computed results predicted all of the trends observed in the experimental data quite well. In addition, a simple analytic model based on potential flow was developed to provide a more detailed understanding of how lift-enhancing tabs work. The tabs were modeled by a point vortex at the air-foil or flap trailing edge. Sensitivity relationships were derived which provide a mathematical basis for explaining the effects of lift-enhancing tabs on a multi-element airfoil. Results of the modeling effort indicate that the dominant effects of the tabs on the pressure distribution of each element of the airfoil can be captured with a potential flow model for cases with no flow separation.
Ashby, Dale L.↗
Nonstationary flow about a wing-aileron-tab combination including aerodynamic balance
This paper presents a continuation of the work published in Technical Report no. 496. The results of that paper have been extended to include the effect of aerodynamic balance and the effect of a tab added to the aileron. The aerodynamic coefficients are presented in a form convenient for application to the flutter problem.
Theodorsen, Theodore↗
Numerical investigation of multi-element airfoils
The flow over multi-element airfoils with flat-plate lift-enhancing tabs was numerically investigated. Tabs ranging in height from 0.25 percent to 1.25 percent of the reference airfoil chord were studied near the trailing edge of the main-element. This two-dimensional numerical simulation employed an incompressible Navier-Stokes solver on a structured, embedded grid topology. New grid refinements were used to improve the accuracy of the solution near the overlapping grid boundaries. The effects of various tabs were studied at a constant Reynolds number on a two-element airfoil with a slotted flap. Both computed and measured results indicated that a tab in the main-element cove improved the maximum lift and lift-to-drag ratio relative to the baseline airfoil without a tab. Computed streamlines revealed that the additional turning caused by the tab may reduce the amount of separated flow on the flap. A three-element airfoil was also studied over a range of Reynolds numbers. For the optimized flap rigging, the computed and measured Reynolds number effects were similar. When the flap was moved from the optimum position, numerical results indicated that a tab may help to reoptimize the airfoil to within 1 percent of the optimum flap case.
Cummings, Russell M.↗
Testing of the Trim Tab Parametric Model in NASA Langley's Unitary Plan Wind Tunnel
In support of NASA's Entry, Descent, and Landing technology development efforts, testing of Langley's Trim Tab Parametric Models was conducted in Test Section 2 of NASA Langley's Unitary Plan Wind Tunnel. The objectives of these tests were to generate quantitative aerodynamic data and qualitative surface pressure data for experimental and computational validation and aerodynamic database development. Six component force-and-moment data were measured on 38 unique, blunt body trim tab configurations at Mach numbers of 2.5, 3.5, and 4.5, angles of attack from -4deg to +20deg, and angles of sideslip from 0deg to +8deg. Configuration parameters investigated in this study were forebody shape, tab area, tab cant angle, and tab aspect ratio. Pressure Sensitive Paint was used to provide qualitative surface pressure mapping for a subset of these flow and configuration variables. Over the range of parameters tested, the effects of varying tab area and tab cant angle were found to be much more significant than varying tab aspect ratio relative to key aerodynamic performance requirements. Qualitative surface pressure data supported the integrated aerodynamic data and provided information to aid in future analyses of localized phenomena for trim tab configurations.
Murphy, Kelly J.↗
Supersonic jet mixing enhancement by delta-tabs
The results of a continuing investigation of the effect of vortex generators, in the form of small tabs at the nozzle exit, on the evolution of a jet are reported. Primarily, tabs of triangular shape are considered, and the effect is studied up to an equivalent jet Mach number of 1.8. By changing the orientation of the tab with respect to the nozzle exit plane, streamwise vortex pairs of opposite sign were generated. This resulted in either an outward election of jet core fluid into the ambient or an inward indentation of the mixing layer into the core of the jet. A triangular shaped tab with its apex leaning downstream, referred to as a delta tab, was found to be the most effective in influencing the jet evolution. Two delta tabs, spaced 180 degrees apart, completely bifurcated the jet. Four delta tabs increased jet mixing substantially, more than by various other methods tried previously; the mass flux at fourteen jet diameters downstream from the nozzle increased by about 50 percent over that for the no tab case. The tabs were found to be effective in jets with laminar or turbulent boundary layers as well as in jets with low or high core turbulence intensities.
Zaman, K. B. M. Q.↗
Supersonic jet mixing enhancement by 'delta-tabs'
The results of a continuing investigation of the effect of vortex generators, in the form of small tabs at the nozzle exit, on the evolution of a jet are reported. Primarily, tabs of triangular shape are considered, and the effect is studied up to an equivalent jet Mach number of 1.8. By changing the orientation of the tab with respect to the nozzle exit plane, streamwise vortex pairs of opposite sign were generated. This resulted in either an outward selection of jet core fluid into the ambient or an inward indentation of the mixing layer into the core of the jet. A triangular shaped tab with its apex leaning downstream, referred to as a delta tab, was found to be the most effective in influencing the jet evolution. Two delta tabs, spaced 180 degrees apart, completely bifurcated the jet. Four delta tabs increased jet mixing substantially, more than by various other methods tried previously; the mass flux at fourteen jet diameters downstream from the nozzle increased by about 50 percent over that for the no tab case. The tabs were found to be effective in jets with laminar or turbulent boundary layers as well as in jets with low or high core turbulence intensities.
Zaman, K. B. M. Q.↗
Investigation at Transonic Speeds of the Effect of a Positive-lift Balancing Tab on the Hinge-moment and Lift-characteristics of a Full-span Flap on a Tapered 45 Degrees Sweptback Wing of Aspect Ratio 3
Explore the source record for details and available documents.
Lockwood, Vernard E↗
Wind-Tunnel Investigation of Control-Surface Characteristics XX : Plain and Balanced Flaps on an NACA 0009 Rectangular Semispan Tail Surface
Correlation is established between aerodynamic characteristics of control surfaces in two-dimensional and three-dimensional flow. Slope of lift curve was affected little by overhang and balance-nose shape, but increased by sealing flap-nose gap. Effectiveness of balancing tab was same for sealed plain flap and unsealed overhang flap. Changes in hinge-moment coefficient were diminished by sealing gap. Values measured by three-dimensional flow disagreed with two-dimensional flow values until aspect ratio corrections were made.
CONTROL SURFACES, BALANCED↗
Pressure-distribution investigation of an N.A.C.A. 0009 airfoil with a 50-percent-chord plain flap and three tabs
Pressure-distribution tests of an N.A.C.A. 0009 airfoil with a 50-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made in the N.A.C.A. 4- by 6- foot vertical tunnel. The tests supplied aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab. Plots are also given of increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs. The experimental results and values computed by analytical methods are in good agreement for small flap and tab deflections. The results of the tests indicated that the effectiveness of all three tab sizes in reducing flap hinge moments decreased with increasing flap deflection.
Street, William G↗
Experimental investigation of stability and stall flutter of a free-floating wing V/STOL model
An experimental investigation was made of the static and dynamic stability characteristics of a one-fourth scale model of a tilt-propeller free-wing V/STOL aircraft. The effects of wing pivot location, wing chord, trailing-edge angle, propeller tilt angle, and thrust were studied, and a limited evaluation was made of high-lift devices. A dynamically similar wing was used to measure frequency and damping ratio from transient response data in the linear aerodynamic regime and the results were compared to quasi-steady and unsteady aerodynamic theory. It was found that at high trim angles of attack, in the nonlinear aerodynamic regime, stall flutter oscillations occurred with typical amplitudes ranging from 15 to 20 deg. Wing control tab deflection was effective in initiating and terminating stall flutter but variations in configuration or operating conditions did not greatly influence the occurrence of characteristics of the oscillations.
Ormiston, R. A.↗