SEARCH · Search NASA

Results for “TAIL ASSEMBLY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Modeling the Earth's magnetospheric magnetic field confined within a realistic magnetopause

Empirical data-based models of the magnetosphereic magnetic field have been widely used during recent years. However, the existing models (Tsyganenko, 1987, 1989a) have three serious deficiencies: (1) an unstable de facto magnetopause, (2) a crude parametrization by the K(sub p) index, and (3) inaccuracies in the equatorial magnetotail B(sub z) values. This paper describes a new approach to the problem; the essential new features are (1) a realistic shape and size of the magnetopause, based on fits to a large number of observed crossing (allowing a parametrization by the solar wind pressure), (2) fully controlled shielding of the magnetic field produced by all magnetospheric current systems, (3) new flexible representations for the tail and ring currents, and (4) a new directional criterion for fitting the model field to spacecraft data, providing improved accuracy for field line mapping. Results are presented from initial efforts to create models assembled from these modules and calibrated against spacecraft data sets.

Tsyganenko, N. A.↗

NASA NTRS1987

Independent Orbiter Assessment (IOA): Analysis of the orbital maneuvering system

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) are presented. The IOA approach features a top-down analysis of the hardware to determine failure modes, criticality, and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The independent analysis results for the Orbital Maneuvering System (OMS) hardware are documented. The OMS provides the thrust to perform orbit insertion, orbit circularization, orbit transfer, rendezvous, and deorbit. The OMS is housed in two independent pods located one on each side of the tail and consists of the following subsystems: Helium Pressurization; Propellant Storage and Distribution; Orbital Maneuvering Engine; and Electrical Power Distribution and Control. The IOA analysis process utilized available OMS hardware drawings and schematics for defining hardware assemblies, components, and hardware items. Each level of hardware was evaluted and analyzed for possible failure modes and effects. Criticality was asigned based upon the severity of the effect for each failure mode.

Prust, C. D.↗

NASA NTRS1994

Hot gas ingestion effects on fuel control surge recovery and AH-1 rotor drive train torque spikes

This report summarizes the work accomplished through computer simulation to understand the impact of the hydromechanical turbine assembly (TA) fuel control on rocket gas ingestion induced engine surges on the AH-1 (Cobra) helicopter. These surges excite the lightly damped torsional modes of the Cobra rotor drive train and can cause overtorqueing of the tail rotor shaft. The simulation studies show that the hydromechanical TA control has a negligible effect on drive train resonances because its response is sufficiently attenuated at the resonant frequencies. However, a digital electronic control working through the TA control's separate, emergency fuel metering system has been identified as a solution to the overtorqueing problem. State-of-the-art software within the electronic control can provide active damping of the rotor drive train to eliminate excessive torque spikes due to any disturbances including engine surges and aggressive helicopter maneuvers. Modifications to the existing TA hydromechanical control are relatively minor, and existing engine sensors can be utilized by the electronic control. Therefore, it is concluded that the combination of full authority digital electronic control (FADEC) with hydromechanical backup using the existing TA control enhances flight safety, improves helicopter performance, reduces pilot workload, and provides a substantial payback for very little investment.

Tokarski, Frank↗

NASA NTRS1993

Aircraft empennage structural detail design

The purpose of this project is to provide an empennage structural assembly that will withstand the operational loads defined in FAR Part 23, as well as those specified in the statement of work, i.e. snow, rain, humidity, tiedown forces, etc. The goal is to provide a simple yet durable lightweight structure that will transfer the aerodynamic forces produced by the tail surfaces through the most efficient load path to the airframe. The structure should be simple and cost-effective to manufacture and repair. All structures meet or exceed loading and fatigue criteria. The structure provides for necessary stiffness and ease of maintenance.

Lesnewski, David↗

NASA NTRS2010

A Flight-Calibrated Methodology for Determination of Cassini Thruster On-Times for Reaction Wheel Biases

This paper describes a methodology for accurate and flight-calibrated determination of the on-times of the Cassini spacecraft Reaction Control System (RCS) thrusters, without any form of dynamic simulation, for the reaction wheel biases. The hydrazine usage and the delta V vector in body frame are also computed from the respective thruster on-times. The Cassini spacecraft, the largest and most complex interplanetary spacecraft ever built, continues to undertake ambitious and unique scientific observations of planet Saturn, Titan, Enceladus, and other moons of Saturn. In order to maintain a stable attitude during the course of its mission, this three-axis stabilized spacecraft uses two different control systems: the RCS and the reaction wheel assembly control system. The RCS is used to execute a commanded spacecraft slew, to maintain three-axis attitude control, control spacecraft's attitude while performing science observations with coarse pointing requirements, e.g. during targeted low-altitude Titan and Enceladus flybys, bias the momentum of reaction wheels, and to perform RCS-based orbit trim maneuvers. The use of RCS often imparts undesired delta V on the spacecraft. The Cassini navigation team requires accurate predictions of the delta V in spacecraft coordinates and inertial frame resulting from slews using RCS thrusters and more importantly from reaction wheel bias events. It is crucial for the Cassini spacecraft attitude control and navigation teams to be able to, quickly but accurately, predict the hydrazine usage and delta V for various reaction wheel bias events without actually having to spend time and resources simulating the event in flight software-based dynamic simulation or hardware-in-the-loop simulation environments. The methodology described in this paper, and the ground software developed thereof, are designed to provide just that. This methodology assumes a priori knowledge of thrust magnitudes and thruster pulse rise and tail-off time constants for eight individual attitude control thrusters, the spacecraft's wet mass and its center of mass location, and a few other key parameters.

Earth Mean Equatorial↗

NASA NTRS2012

Using the EUV to Weigh a Sun-Grazing Comet as it Disappears in the Solar Corona

On July 6,2011, the Atmospheric Imaging Assembly (AlA) on the Solar Dynamics Observatory (SDO) observed a comet in most of its EUY passbands. The comet disappeared while moving through the solar corona. The comet penetrated to 0.146 solar radii ($\simapprox.100,000 km) above the photosphere before its EUY faded. Before then, the comet's coma and a tail were observed in absorption and emission, respectively. The material in the variable tail quickly fell behind the nucleus. An estimate of the comet's mass based on this effect, one derived from insolation, and one using the tail's EUY brightness, all yield $\sim 50$ giga-grams some 10 minutes prior to the end of its visibility. These unique first observations herald a new era in the study of Sun-grazing comets close to their perihelia and of the conditions in the solar corona and solar wind. We will discuss the observations and interpretation of the comet by SDO as well as the coronagraph observations from SOHO and STEREO. A search of the SOHO comet archive for other comets that could be observed in the SDO; AlA EUY channels will be described

Pesnell, William Dean↗

NASA NTRS2017

Observations of Deep Ionospheric F-Region Density Depletions with FPMU Instrumentation and their Relationship with the Global Dynamics of the June 22-23, 2015 Geomagnetic Storm

The magnetic storm that commenced on June 22-23, 2015 was one of the largest storms in our current solar cycle, resulting from an active region on the Sun that produced numerous coronal mass ejections (CMEs) and associated interplanetary shock waves. On June 22 at 18:36 UT the magnetosphere was impacted by the shock wave on the magnetosphere. Observations from several spacecraft observed the dynamic response of the magnetosphere and ionosphere. MMS observatories in the near earth tail These low altitude measurements are correlated in the magnetosphere with particle flux dropouts measured by MMS We follow the timing of this storm in the ionosphere with the density depletions throughout the ISS orbits, DMSP drift velocities, and enhanced AMPERE Birkland currents. Together these observations and simulation results will be assembled to provide each region's context to the global dynamics and time evolution of the storm. The models during these event support and flesh out the puzzle of the global dynamics.

Coffey, Victoria↗

NASA NTRS1978

Application of advanced technologies to small, short-haul aircraft

The results of a preliminary design study which investigates the use of selected advanced technologies to achieve low cost design for small (50-passenger), short haul (50 to 1000 mile) transports are reported. The largest single item in the cost of manufacturing an airplane of this type is labor. A careful examination of advanced technology to airframe structure was performed since one of the most labor-intensive parts of the airplane is structures. Also, preliminary investigation of advanced aerodynamics flight controls, ride control and gust load alleviation systems, aircraft systems and turbo-prop propulsion systems was performed. The most beneficial advanced technology examined was bonded aluminum primary structure. The use of this structure in large wing panels and body sections resulted in a greatly reduced number of parts and fasteners and therefore, labor hours. The resultant cost of assembled airplane structure was reduced by 40% and the total airplane manufacturing cost by 16% - a major cost reduction. With further development, test verification and optimization appreciable weight saving is also achievable. Other advanced technology items which showed significant gains are as follows: (1) advanced turboprop-reduced block fuel by 15.30% depending on range; (2) configuration revisions (vee-tail)-empennage cost reduction of 25%; (3) leading-edge flap addition-weight reduction of 2500 pounds.

Andrews, D. G.↗

NASA NTRS2004

Simulations of Hyperthermal Oxygen Beam Exposures

Pulsed sources of hyper-thermal O-atoms are now being extensively used to simulate low-earth orbit (LEO) surface exposure environments. The peak flux of these sources is many orders of magnitude larger than the corresponding LEO flux. Although it is desirable to accelerate the test by using higher fluxes than found in LEO, even commonly used fluxes are large enough to produce multi-collision effects by causing a build-up of gas at the sample surface. In this paper we characterize the physical consequences to the experiment using the direct simulation Monte Carlo (DSMC) method, DSMC allows us to extract the distributions of energy and impact angle for the O-atoms that reach the surface, and to record how strongly the gas build-up at the target assembly deflects flux from downstream instrumentation. By considering a range of source fluxes, we determine the onset conditions and severity of these multi-collision effects. We find that even at common experimental fluxes with a normally incident beam string a flat surface sample, the energy distribution of incident O-atoms broadens and develops a significant low-energy tail. The angular distributions also broaden significantly. The number of O-atoms that reach downstream instrumentation is decreased by approximately 50%. These simulations will aid in the calibration of ground-based O-atom measurements,a nd provide a model for the energy and angular distributions of O-atoms that actually impinge on surface samples.

Finchum, A.↗

NASA NTRS2003

DSMC Simulations of Hyperthermal Oxygen Beam Exposures

Pulsed sources of hyper-thermal O-atoms are now being extensively used to simulate low-earth orbit (LEO) surface exposure environments. The peak flux of these sources is many orders of magnitude larger than the corresponding LEO flux. Although it is desirable to accelerate the test by using higher fluxes than found in LEO, even commonly used fluxes are large enough to produce multi-collision effects by causing a build-up of gas at the sample surface. In this paper we characterize the physical consequences to the experiment using the direct simulation Monte Carlo (DSMC) method. DSMC allows us to extract the distributions of energy and impact angle for the O-atoms that reach the surface, and to record how strongly the gas build-up at the target assembly deflects flux from downstream instrumentation. By considering a range of source fluxes, we determine the onset conditions and severity of these multi-collision effects. We find that even at common experimental fluxes with a normally incident beam striking a flat surface sample, the energy distribution of incident O-atoms broadens and develops a significant low-energy tail. The angular distributions also broaden significantly. The number of O-atoms that reach downstream instrumentation is decreased by approximately 50%. These simulations will aid in the calibration of ground-based O-atom measurements, and provide a model for the energy and angular distributions of O-atoms that actually impinge on surface samples.

Cline, Jason A.↗

NASA NTRSDate not supplied

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

A transonic, high Reynolds number wind tunnel test of a Boundary Layer Ingesting Tailcone System (BLITS) was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center during the spring of 2023. The test was sponsored by the NASA Advanced Air Transport Technology Project and produced a large dataset to help in the development and validation of an integrated airframe-turbomachinery computational simulation capability. The Common Research Model with Tail Cone Thruster (CRM-TCT) configuration was tested at Mach numbers from 0.75 to 0.85 and Reynolds number based on mean aerodynamic chord from 5 to 15 million, with the objective of characterizing the tailcone nacelle inlet pressure and flow angle profile, characterizing the aftbody boundary layer (BL), and evaluating the overall airframe configuration performance. The test article included multiple tailcone nacelle assemblies with different measurement objectives, and each assembly was able to be controlled remotely and rotate in small increments, allowing for an increased measurement density for characterizing the nacelle inlet distortion. Additionally, the use of cryogenic-rated miniature BL rakes was successful in measuring boundary layer heights on the aftbody. Sensitivities of the measured quantities of interest to Mach number, Reynolds number, angle of attack, and nacelle weight flow rate are also presented.

boundary layer ingestion (BLI)↗

NASA NTRSDate not supplied

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

boundary layer ingestion (BLI)↗

NASA NTRS2012

Further Evaluation of Scaling Methods for Rotorcraft Icing

The paper will present experimental results from two recent icing tests in the NASA Glenn Icing Research Tunnel (IRT). The first test, conducted in February 2009, was to evaluate the current recommended scaling methods for fixed wing on representative rotor airfoils at fixed angle of attack. For this test, scaling was based on the modified Ruff method with scale velocity determined by constant Weber number and water film Weber number. Models were un-swept NACA 0012 wing sections. The reference model had a chord of 91.4 cm and scale model had a chord of 35.6 cm. Reference tests were conducted with velocity of 100 kt (52 m/s), droplet medium volume diameter (MVD) 195 m, and stagnation-point freezing fractions of 0.3 and 0.5 at angle of attack of 5deg and 7deg . It was shown that good ice shape scaling was achieved with constant Weber number for NACA 0012 airfoils with angle of attack up to 7deg . The second test, completed in May 2010, was primarily focused on obtaining transient and steady-state iced aerodynamics, ice accretion and shedding, and thermal icing validation data from an oscillating airfoil section over some selected ranges of icing conditions and blade assembly operational configurations. The model used was a 38.1-cm chord Sikorsky SC2110 airfoil section installed on an airfoil test apparatus with oscillating capability in the IRT. For two test conditions, size and condition scaling were performed. It was shown that good ice shape scaling was achieved for SC2110 airfoil at dynamic pitching motion. The data obtained will be applicable for future main rotor blade and tail rotor blade applications.

Tsao, Jen-Ching↗

NASA NTRS1990

Computing interference flows past cylinder-fin-sting assembly in and near a cavity

The internal carriage of stores by the military aircraft is an option, particularly at high speeds, for a possible reduction in the aerodynamic drag and in the radar observability. Trade studies of this option, which include the safe separation of stores from their bays and aerodynamic complications of a cavity flow, require studying the aircraft and the stores together. With this motivation, the computer code, VISCC, is developed to solve the three-dimensional, Reynolds-averaged, unsteady, compressible, and complete Navier-Stokes equations. The store considered here for simulation is a missile configuration with four tail fins and an L-shaped offset sting. The missile is placed first directly above the opening of a rectangular box cavity, then submerged completely inside the cavity. The freestream Mach and the unit Reynolds numbers are 2.75 and 2.97 million per foot, respectively. The results of the time-accurate computations depict these complex flows and help understanding the interference effects. The time-averaged surface pressures compare favorably with the available wind tunnel data.

Baysal, O.↗

NASA NTRS1947

Low-Speed Wind-Tunnel Tests of a Pilotless Aircraft Having Horizontal and Vertical Wings and Cruciform Tail

Low-speed tests of a pilotless aircraft were conducted in the Langley propeller-research tunnel to provide information for the estimation of the longitudinal stability and. control, to measure the aileron effectiveness, and to calibrate the radome and the Machmeter pitot-static orifices. It was found that the model possessed a stEb.le variation of elevator angle required for trim throughout the speed range at the design angle of attack. A comparison of the airplane with and without JATO units and with an alternate rocket booster showed that a large loss in longitudinal stability and control resulting from the addition of the rocket booster to the aircraft was sufficient to make the rocket-booster assembly unsatisfactory as an alternate for the JATO units. Reversal of the aileron effectiveness was evident at positive deflections of the vertical wing flap indicating that the roll-stabilization system would produce roiling moments in a tight right turn contrary to its design purpose. Vertical-wing-flap deflections caused large errors in the static-pressure reading obtained by the original static-tube installation. A practical installation point on the fuselage was located which should yield reliable measurement of the free-stream static pressure.

Mastrocola, N↗

NASA NTRS1986

Infrared point sources aligned with the SgrA(asterisk) non-thermal radio source

Assembled 0.7-5.0 micron observational data for two point sources approximately aligned with the compact nonthermal radio source SgrA(asterisk) in the Galactic center, thus far interpreted as being from the same object on the basis of their position and spectral continuity, are presently given alternative interpretations. While the object must be a hot star surrounded by a circumstellar dust cloud if it is a foreground star, a Galactic center position calls for an unorthodox extinction curve which suggests that the IR emission may be the Rayleigh-Jeans tail of a hot star or star cluster, or perhaps a thermal accretion disk.

Stein, W. A.↗

NASA NTRS1977

Shuttle carrier aircraft flight tests

Since the Space Shuttle will need to be transported from its place of assembly to the launch site, a method has been developed whereby the Shuttle rides piggyback on a modified Boeing 747, called the Shuttle carrier aircraft (SCA). This paper describes tests of the SCA in its mated configuration. Tests include: flutter, found to decrease when fiberglass and wood fairings were added to the base of each supporting pylon; stability and control, found to be acceptable after damping with control pulses; noise and buffet, found high but acceptable; and climb, in which drag was marked but acceptable with the special rated thrust (SRT) power setting. Simulated launch maneuvers were undertaken at an airspeed of 273 KCAS. Transport of the Shuttle takes place with the Shuttle tail cone on, at a cruise speed of 288 KCAS at an altitude of 22,000 feet.

Fulton, F. L., Jr.↗

NASA NTRS1983

Preliminary observations of velocity fields at the solar poles

Using the 13 m Littrow spectrograph at Sacramento Peak Observatory, the Doppler shift of Fe I 5863 A in the polar regions of the sun over a 20 day interval is studied. The daily observations were assembled into a polar projection of the line-of-sight velocity field. The projection shows a very clear pattern of supergranulation. When a low-pass spatial filter is run over the data, a pattern of large-scale (80-100 Mm) velocity features can be seen. Cross-correlation studies show that the supergranular pattern rotates with a synodic period of 35 days, while there is evidence that the larger features rotate with a shorter period of about 30 days. At present, it is not possible to say whether the large-scale patterns represent a new scale of convection (possibly related to the dominant convective eddy in the lower solar convection zone) or to the low-wavenumber tail of a distribution of supergranular cells.

Cram, L. E.↗