Search NASA⌕ Search

SEARCH · Search NASA

Results for “TURBINES, GAS - PERFORMANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Cyber-Physical Simulation of an Innovative Solid Oxide Electrolysis Cell - Gas Turbine (SOEC-GT) Hybrid Energy System

To produce green hydrogen at scale and at low cost, the solid oxide electrolysis cell (SOEC) systems would be tied to renewable power sources (mainly solar and wind), leveraging zero-carbon electricity at low prices and even nearly free during overgeneration scenarios. However, due to the intermittency of renewable power generation, the SOEC system is subjected to rapid load transitions that occur not only in diurnal cycles but also in short timeframes (e.g., sub-minute). This can result in fast degradation and thus greatly reduce the SOEC’s lifetime. Our team at the National Energy Technology Laboratory has demonstrated that the anode air flow can have a crucial role in SOEC thermal management. Typically, a higher air flow rate can help to mitigate the local temperature gradient distortion during rapid load transitions. To move a large amount of air, the gas turbine (GT; i.e., compressor-turbine-generator set) has been regarded as the most mature and efficient technology. In this presentation, we show the configuration and preliminary results of an innovative SOEC-GT hybrid energy system in a cyber-physical simulation (CPS) approach.

Zhang, Biao↗
DOE OSTI2022

In-situ optical monitoring of gas turbine blade coatings under operational extreme environments

High temperature material systems consisting of thermal barrier coatings and the underlying superalloys are key to achieving higher gas temperatures which in turn control engine efficiencies and reduce emissions. With engine temperatures in excess of the limits that metallic blades and vanes can endure, advanced monitoring techniques that ensure the integrity and durability of these coatings are paramount to continuous and safe operation. Optical methods have the benefit of being non-invasive and are able to capture data under limited access available for monitoring the hot-section of turbines. Addressing Topic 5 on Advanced Instrumentation, the research and development effort for this project titled “In situ optical monitoring of gas turbine blade coatings under operational extreme environments” was completed by University of Central Florida researchers, including Raghavan (PI) and Ghosh (co-PI). In this project, the research team leveraged intrinsic properties of coatings and rare-earth dopants as active and intelligent “sensors” through their optical properties. The outcomes of this project pave the way for diagnostics of turbine blade coatings, under operating environments, through the development of the sensing thermal barrier coating configurations, calibration and associated instrumentation while ensuring coating integrity and durability goals are concurrently met.

42 ENGINEERING↗
DOE OSTI2023

Transition to High-Hydrogen Fueled Advanced Gas Turbine Engines for Land-Based Power Generation and Industrial Applications

Invited lecture presented as part of the 2023 University of Central Florida - Mechanical and Aerospace Engineering Seminar Series. These slides discuss the role of multi-sourced hydrogen for electrical power generation. Particular focus is given to the combustion of hydrogen for the purpose of chemical to thermal energy. Pressure gain combustion is given as an example technology that could leverage hydrogen as a fuel source ultimately leading to higher rates of energy conversion (chemical to electrical) resulting in greater energy security and reduced cost of electricity.

advanced gas turbines↗
DOE OSTI2023

Surface Roughness Effects from Additive Manufacturing in High Efficiency Gas Turbine Combustion Systems

In the past, clean combustion systems were characterized by high system development costs due to growing complexity and escalating manufacturing costs from conventional manufacturing processes. As a result, high efficiency concepts are difficult to design and more difficult to be cost-effectively manufactured. In recent years, with the introduction of additive manufacturing (AM) technologies, the rapid prototyping and mass production processes of clean combustion systems are promising to be significantly simplified with significant reduction in terms of engine manufacturing cost and engine energy cost. Compared with conventional manufacturing built parts, the AM process enabled a simpler design to be adopted for the nozzle, reducing the number of required braze and weld joints from twenty-five to just five. The resulting nozzle was 25% lighter and five times more durable and contributed to a 15% reduction in fuel burn in comparison with the previous model produced. Applying these improvements to a fleet of 5,000 turbofan engines at 150 kN thrust would result in fuel cost savings of $6B annually (at $5/gallon Jet-A fuel price, 700 gallon/hour fuel consumption rate, and 2,300 operational hours per year),and reduce CO2 emissions by more than 25 million tons per year. These advances support core Department of Energy (DOE)missions in energy efficiency, improving productivity, and environmental sustainability. Maximizing the benefit of these new capabilities will require high prediction capability of high speed turbulent flow with wall modeled Large Eddy Simulation (LES). GE Aviation maintains that advanced simulation technology and supercomputing is required in order to provide the appropriate boundary conditions to realize the maximum potential of AM and Ceramic Matrix Composite to reduce cooling flow, a first order penalty on the Brayton cycle. The algorithm developed using the ANSYS/Fluent software would provide the foundation for entirely new avenues of research and development with potential multi-billion dollar impact to the US economy, and significant reduction in carbon based emissions across the aerospace and power generation industries. The formulation of this iWLES (integral wall model for LES) is generic and allows to capture the changes in flow dynamics that have a significant impact on the wall bounded flow characteristics, such as swirler effective area, bulk swirl number, local pressure distribution, exit velocity profile, and turbulence kinetic energy profile. A periodic channel flow with rough flat plate is simulated using LES (Wall-Adapting Local Eddy-viscosity) model to verify the implementation of iWLES in the Fluent User Defined Function (UDF). As the flow fields are highly sensitive due to surface roughness of the wall bounded flows in the combustion systems, there is significant potential to conduct further LES studies focusing on the turbulence boundary layer interaction. Accurately capturing near wall physics will elucidate the impact of rough surfaces on combustor flow and aero-thermal interactions.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Impact of Biofuel Blends on Black Carbon Emissions from a Gas Turbine Engine

With a view towards renewable feedstock while decreasing the CO2 footprint associated with jet travel, biofuels are receiving increasing interest. Presented here is an overview of non-volatile particulate matter (nvPM) emissions, i.e. “soot” as gauged by varied TEM analyses for a J-85 turbojet fueled with Jet-A as well as with blends of Jet-A using Camelina biofuel. A unifying explanation is provided encompassing fuels and spanning length scales across three orders of magnitude. The variation of primary particle size, aggregate size and nanostructure are analyzed as a function of biofuel blend across range of engine thrust levels. The postulate is based on where fuels start along the soot formation pathway. Increasing biofuel content lowers aromatic concentration while placing increasing dependence upon fuel pyrolysis reactions to form the requisite concentration of aromatics for particle inception and growth. The required “kinetic” time for pyrolysis reactions to produce benzene and multi-ring PAHs allows increased fuel-air mixing by turbulence, diluting the fuel-rich soot-forming regions, effectively lowering their equivalence ratio. With a lower precursor concentration, particle inception is slowed, the resulting concentration of primary particles is lowered and smaller aggregates. The lower equivalence ratio also results in smaller primary particles given the lower concentration of growth species.

Kumal, Raju R.↗
DOE OSTI2025

Corrosion of Rare-Earth Disilicate Environmental Barrier Coatings in Gas Turbine Environments—Part 2: Microstructure Model

A model for the volatization of ytterbium disilicate (YbDS) by water vapor is developed. The new model is based on the Deal & Grove theory of the thermal oxidation of silicon [1], generalized here to account for the multi-step, second-order chemical reactions for silica depletion, multi-component mixture effects, and the unsteady porous microstructural evolution of the corroded inner zone. With the new model, the fundamental kinetic rate and standard porous media parameters are determined using the atmospheric steam jet impingement experiment of Ridley & Opila [2] and compared to results from the original Deal & Grove model. Fixing the input parameters in each respective model, a validation study (blind prediction) is presented for the high Reynolds number (1 × 105) and high pressure (14.7 atm) burner rig experiment of Wan et al. [3].

Cha, Chong M [Rolls Royce]↗
DOE OSTI2023

Effects of additively manufactured surface roughness on small diameter plenums with multiple side discharges for high temperature gas turbine blade cooling applications

Combined heat and power (CHP) applications have significant environmental and economic benefits that are consistent with the goals of the U.S. Department of Energy (DOE). One area that is currently being studied includes the potential benefits of CHP turbine operation at higher turbine inlet temperatures. Internal cooling concepts enabled by additive manufacturing (AM) are of primary interest. Here, the effectiveness of internal cooling is hindered by many factors such as velocity distribution of the cooling air to the hot surface considering impingement cooling. To simulate cooling air exiting from a series of orifices for internal cooling in an airfoil, a straight smooth wall tubing with multiple side discharging orifices is used and compared to additively manufactured tubing (Ti6Al4V Grade 23) with orifice size and spacing as well as inner and outer diameters identical to the smooth wall tubing. Similar to flow discharging form perforated pipes, the flow discharged from individual orifices along the tubes in this study is found to be nonuniformly distributed, and the horizontal (axial direction) momentum can be observed from the experimental data. Discharge velocities have been measured with two-dimensional (2D) particle imaging velocimetry (PIV) and single element hot wire anemometry. Numerical analysis has also been conducted to predict the velocity distributions along the orifices in the smooth wall and additive manufacturing (AM) tubing, which are inherited with surface roughness. Numerical and measured results in this study are compared, presented, and discussed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Surface Roughness Effects from Additive Manufacturing in High Efficiency Gas Turbine Combustion Systems

In the past, clean combustion systems were characterized by high system development costs due to growing complexity and escalating manufacturing costs from conventional manufacturing processes. As a result, high efficiency concepts are difficult to design and more difficult to be cost-effectively manufactured. In recent years, with the introduction of additive manufacturing (AM) technologies, the rapid prototyping and mass production processes of clean combustion systems are promising to be significantly simplified with significant reduction in terms of engine manufacturing cost and engine energy cost. Compared with conventional manufacturing built parts, the AM process enabled a simpler design to be adopted for the nozzle, reducing the number of required braze and weld joints from twenty-five to just five. The resulting nozzle was 25% lighter and five times more durable and contributed to a 15% reduction in fuel burn in comparison with the previous model produced. Applying these improvements to a fleet of 5,000 turbofan engines at 150 kN thrust would result in fuel cost savings of $ \$ $6B annually (at $ \$ $5/gallon Jet-A fuel price, 700 gallon/hour fuel consumption rate, and 2,300 operational hours per year), and reduce CO2 emissions by more than 25 million tons per year. These advances support core Department of Energy (DOE) missions in energy efficiency, improving productivity, and environmental sustainability. Maximizing the benefit of these new capabilities will require high prediction capability of high speed turbulent flow with wall modeled Large Eddy Simulation (LES). GE Aviation maintains that advanced simulation technology and supercomputing is required in order to provide the appropriate boundary conditions to realize the maximum potential of AM and Ceramic Matrix Composite to reduce cooling flow, a first order penalty on the Brayton cycle. The algorithm developed using the ANSYS/Fluent software would provide the foundation for entirely new avenues of research and development with potential multi-billion dollar impact to the US economy, and significant reduction in carbon based emissions across the aerospace and power generation industries. The formulation of this iWLES (integral wall model for LES) is generic and allows to capture the changes in flow dynamics that have a significant impact on the wall bounded flow characteristics, such as swirler effective area, bulk swirl number, local pressure distribution, exit velocity profile, and turbulence kinetic energy profile. A periodic channel flow with rough flat plate is simulated using LES (Wall-Adapting Local Eddy-viscosity) model to verify the implementation of iWLES in the Fluent User Defined Function (UDF). As the flow fields are highly sensitive due to surface roughness of the wall bounded flows in the combustion systems, there is significant potential to conduct further LES studies focusing on the turbulence boundary layer interaction. Accurately capturing near wall physics will elucidate the impact of rough surfaces on combustor flow and aero-thermal interactions.

42 ENGINEERING↗
DOE OSTI2025

Implementation of disruptive designs for gas turbine components using direct energy deposition additive manufacturing

This research aims to develop a framework for establishing the correlation between in-situ monitoring data, process parameters, and microstructure evolution in blown-powder laser-directed energy deposition (DED) additive manufacturing (AM). To achieve this, a comprehensive manufacturing framework has been developed, spanning from in-situ data acquisition, melt-pool simulation, microstructure modeling, and statistical microstructure quantification. A machine learning-based surrogate model is constructed to predict melt pool geometry directly from in-situ coaxial camera data. The surrogate model is trained using outputs from a high-fidelity melt pool simulation, which provides accurate melt pool dimension data under varying process conditions. The predicted melt pool geometry is then used as input to a microstructure model to predict microstructural features. To rigorously compare and analyze microstructures, the project introduces statistical metrics that quantify differences based on key features such as morphology and texture. Microstructures are represented using advanced statistical descriptors including angular chord length distribution, two-point spatial statistics, orientation distribution function, and global spherical harmonic. These representations are used to compute four distinct “dissimilarity scores” that quantitatively capture differences in texture and morphology. This framework is demonstrated to enable automated calibration of simulation parameters by minimizing discrepancies between simulated and target microstructures. The technology developed in this project enables direct correlation between in-situ monitoring data and resulting microstructure, paving the way for adaptive microstructure control in metal AM. This capability strengthens the connection between process parameters and final material properties, facilitating more precise and reliable material design.

36 MATERIALS SCIENCE↗