Results for “Topological materials” — Page 3

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Simulation of Oxidative Etch Pit Formation and Growth on FiberForm

Erosion of carbon surfaces due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface and have much higher reactivity compared to average non-defective sites. Thus, these active sites are the first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective, and increasing their reactivity, thus leading to localized carbon removal around these “active” sites. In this manner, these highly reactive defects serve as nucleation sites for the formation and growth of etch pits, with detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in the presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, the precursor substrate of the PICA Thermal Protection System (TPS) material. The microstructure of virgin FiberForm obtained directly from X-ray microtomography scans is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported into the Porous Microstructure Analysis (PuMA) software and various material properties such as thermal conductivity, elasticity, and permeability are computed. The variation of these properties because of the complex evolution of the surface topology due to the formation of etch pits is studied and analyzed. Furthermore, the effect of pitting is compared to the case of uniform radial shrinking of fibers, which has been the standard for modelling ablation of carbon structures, and significant differences are observed. Thus, a physically realistic model of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to the growth of etch pits. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

DSMC↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRSDate not supplied

Computational Study of Oxidative Etch Pitting in FiberForm and the Effect on Its Material Properties

Erosion of carbon due to oxidation does not occur uniformly but through the formation of localized etch pits because of active surface sites. These active sites are formed due to the presence of atomic defects on the carbon surface, and have much higher reactivity compared to average non-defective sites. Thus, these active sites are first to react during ablation, resulting in their removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these “active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. In order to understand the influence of these etch pits on the material properties of carbon fiber microstructures, we have developed a new capability within direct simulation Monte Carlo (DSMC) to capture the etch pit formation process. This capability is developed within the DSMC code SPARTA (Stochastic PArallel Rarefied-gas Time-accurate Analyzer) and can model the material removal in presence of active sites leading to the formation of etch pits. The focus of the current work will be to study the effect of etch pits on the material properties of FiberForm, a commonly used base material within many thermal protection system materials (TPS). The microstructure of virgin FiberForm obtained directly from X-ray microtomography experiments is used within SPARTA to obtain the ablated geometries with etch pits. These pitted microstructures are then imported within the Porous Microstructure Analysis (PuMA) software and various material properties such as elasticity, thermal conductivity, and permeability are computed. The variation of these properties as a result of the complex evolution of the surface topology due to etch pit formation is studied and analyzed. Furthermore, the effect of pitting is compared to the case of shrinking fibers, which has been the standard for modelling ablation of carbon structures; and significant differences are observed. Thus, such a physically realistic modeling of material removal through the formation of etch pits will be helpful in predicting the degradation of carbon-based TPS more accurately during oxidation; as well as other mechanisms such as spallation, which involves the removal of chunks of material into the flow due to etch pit growth. This will ultimately improve our understanding of the failure modes in these materials due to ablation.

Carbon Ablators↗

NASA NTRS1993

Coronal mass ejections - The link between solar and geomagnetic activity

The phenomenon of coronal mass ejections (CME) is examined with reference to recent work in this field. In particular, attention is given to CMEs close to the sun, CMEs in interplanetary space, solar cycle variations of CMEs, and magnetic field topology and the problem of magnetic flux balance in interplanetary space. It is demonstrated that transient ejections of material from the sun are the cause of almost all large nonrecurrent geomagnetic substorms, as originally suggested by Chapman and his colleagues.

Gosling, J. T.↗

NASA NTRS2005

Titanium Aluminide Scramjet Inlet Flap Subelement Benchmark Tested

A subelement-level ultimate strength test was completed successfully at the NASA Glenn Research Center (http://www.nasa.gov/glenn/) on a large gamma titanium aluminide (TiAl) inlet flap demonstration piece. The test subjected the part to prototypical stress conditions by using unique fixtures that allowed both loading and support points to be located remote to the part itself (see the photograph). The resulting configuration produced shear, moment, and the consequent stress topology proportional to the design point. The test was conducted at room temperature, a harsh condition for the material because of reduced available ductility. Still, the peak experimental load-carrying capability exceeded original predictions.

Krause, David L.↗

NASA NTRSDate not supplied

Making & Breaking the Rules for DED Design

Design for Additive Manufacturing (DfAM) is widely used to describe design activities and guidelines employed in the creation of Additively Manufactured (AM) parts. Basic design rules for widely adopted processes like Powder Bed Fusion (PBF) are relatively understood including material performance, part size constraints, self-supporting angles, overhangs, wall thicknesses, and feature resolution. Complexity is often inherent with PBF using organically inspired solutions through generative design and topology optimization software to create designs that often cannot be realized via traditional manufacturing processes. The design rules for Directed Energy Deposition (DED) are less well known, and, in some cases, the lack of understanding is likely inhibiting broader application of the various DED processes. This presentation covers key design rules for DED fusion processes and elucidates opportunities like multi-material deposition and build approaches ranging from basic features to complex large-scale parts. Complementary to the opportunistic characteristics of DfAM for DED, Manufacture for AM (MfAM) encompasses the restrictive aspects of the manufacturing lifecycle with limitations due to bead width and wall thickness, self-supporting angles, surface texture, microstructural evolution, and residual stresses. AM enabled part design must always consider the entire value chain starting with incoming feedstock (e.g. plate, wire, or powder) and progressing through the printing process, post-processing (e.g. machining, inspection), and final system assembly. Key considerations, like the tradeoffs between feature resolution and build rate, for process and part selection and economic assessments will be discussed as DED is often traded against other AM processes. After highlighting typical DED design rules, we will also show how some of those rules can be broken via use cases and part designs that span the full spectrum of DED processes with examples of various DED part designs.

Additive Manufacturing↗

NASA NTRSDate not supplied

Developing Materials and Coating Technologies for Mitigation of Lunar Dust Adhesion and Abrasion

Lunar regolith was first identified as a major issue during the Apollo missions. There are three characteristics of lunar regolith that cause issues: small size, rough surface topology, and particle charge. The lack of a magnetosphere allows solar wind to bombard the lunar surface which results in the regolith becoming charged. These charged particles will adhere to most surfaces and degrade thermal control systems. The lack of atmosphere and surface liquids on the lunar surface results in the regolith’s small particle size, abrasive topology, and chemical reactivity. When the dust adheres to a surface, or the lunar lander exhaust kicks up dust regolith, it can impair instrument or thermal control system function, abrade optical surfaces, diminish range of motion, and mechanically degrade soft-goods such as gloves and astronaut suits. All of these examples were experienced during the Apollo missions. The objective of this study was to select and evaluate abrasion-resistant ceramic materials for application on the lunar landing equipment.

materials↗

NASA NTRSDate not supplied

Voxel Based Three-Dimensional Topology Optimization of Heat Exchanger Fins

Increasing interest in novel aircraft propulsion systems and potential for unwanted heat generation, or capture and reuse of waste heat, may require increasingly lightweight and high performing heat exchangers. Advances in manufacturing technologies have shown potential to create complex designs, but design tools need more flexibility. This study utilizes genetic algorithm-driven topology optimization to develop high performance heat exchanger fins for critical applications such as aerospace. The solid domain is generated using voxel representation where a voxel value of 1 indicates the solid domain and a voxel value of 0 refers to the fluid domain. The use of voxel representation somewhat matches the digitization of a model that is required to fabricate using additive manufacturing, and also allows for a highly unconstrained geometry. To test the topology optimization approach, a three-dimensional(3D)baseline offset strip fin geometry in steady laminar flow(Reynolds number = 215)with conjugate heat transfer(simultaneous solution of solid and fluid temperature fields)is optimized. New designs are generated using the genetic algorithm (GA) and sent to evaluation by the CFD software OpenFOAM; then the GA sorts and selects the reproduction pool for the following generation. This process is repeated for 60 generations. The study also investigates the effect off in material on the performance of the GA and the resulting designs. The results show that the optimal designs have overall performance improvement of 18% relative to the baseline. Additionally, a fin constructed of a lower conductivity material (such as an Inconel super alloy that might be necessary for waste heat recovery applications)results in lower overall performance improvement (11%)and optimal designs with higher pressure drop relative to their baseline, and relative to optimal designs produced using higher conductivity materials.

3D Optimization↗

NASA NTRS1978

Can X-ray bursts be caused by substorms at a neutron star

A model for X-ray bursts from accreting neutron stars is developed by analogy with geomagnetic substorms. The essential steps in the substorm process are the nearly steady merging or reconnection of the magnetic field in the magnetosphere with the field in the stellar wind, the transport of some of the merged plasma into a magnetically controlled tail, and the explosive release of plasma from the tail into the magnetosphere. The strength of the magnetic field in the stellar wind required to drive a substorm is approximately 0.1 gauss. If the stellar wind is organized into large-scale magnetic sectors, as is the solar wind, topological dissipation will not occur, and the large-scale field will be available for merging at the magnetopause. Once the material is in the tail, the time scales for the Kruskal-Schwarzschild instability and the unidentified instability which drives terrestrial substorms may be comparable. Alternating periods of burst activity and quiescence could be caused by passage from one sector to another with opposite polarity, or be seasonal variations.

Neugebauer, M.↗

NASA NTRS1992

Homogenization models for 2-D grid structures

In the past several years, we have pursued efforts related to the development of accurate models for the dynamics of flexible structures made of composite materials. Rather than viewing periodicity and sparseness as obstacles to be overcome, we exploit them to our advantage. We consider a variational problem on a domain that has large, periodically distributed holes. Using homogenization techniques we show that the solution to this problem is in some topology 'close' to the solution of a similar problem that holds on a much simpler domain. We study the behavior of the solution of the variational problem as the holes increase in number, but decrease in size in such a way that the total amount of material remains constant. The result is an equation that is in general more complex, but with a domain that is simply connected rather than perforated. We study the limit of the solution as the amount of material goes to zero. This second limit will, in most cases, retrieve much of the simplicity that was lost in the first limit without sacrificing the simplicity of the domain. Finally, we show that these results can be applied to the case of a vibrating Love-Kirchhoff plate with Kelvin-Voigt damping. We rely heavily on earlier results of (Du), (CS) for the static, undamped Love-Kirchhoff equation. Our efforts here result in a modification of those results to include both time dependence and Kelvin-Voigt damping.

Banks, H. T.↗

NASA NTRSDate not supplied

Degradation of Carbon Fiber Microstructures Due to Oxidative Etch Pitting

In order to understand the influence of etch pits on the material properties of carbon fiber microstructures, we use the Porous Microstructure Analysis (PuMA) software to create realistic pitted structures from virgin fiber structures and then analyze their degradation as the degree of pitting increases. For that purpose, we developed a pitting module within PuMA that creates pits with user-defined geometry (shape, size) and distribution (defect density) on the surface of arbitrary microstructures. In this work, we consider FiberForm microstructures, which are commonly used as the base material for ablative thermal protection systems (TPS). Using the new pitting module, we mimic the evolution of etch pits on FiberForm as it occurs from oxidation in ablative heating environments, by first importing the virgin FiberForm structure from a micrograph scan and then imposing different pitting conditions by varying pit radii and defect densities. We then leverage PuMA’s capabilities to calculate material properties for each structure. The results clearly show the degradation of thermal conductivity and structural integrity as etch pits grow, and furthermore highlight the complex evolution of the surface topology, which results in significant changes of the flowgeometry and chemical gas-surface interactions. Furthermore, a comparison of these changes with the case of shrinking fibers, which has heretofore been the standard for modelling ablation of carbon structures, yields significant differences. For example, we observe the formation of small chunks of fibers as pits grow in size, which could be released into the surrounding flow environment as spallation particles. This motivates us to continue our efforts of modelling pitting as an integral part of the structural degradation of carbon fiber structures in oxidation environments, which will ultimately improve our understanding of failure mechanisms in those materials.

PuMA↗

NASA NTRSDate not supplied

Degradation of Carbon Fiber Microstructures Due to Oxidative Etch Pitting

In order to understand the influence of etch pits on the material properties of carbon fiber microstructures, we use the Porous Microstructure Analysis (PuMA) software to create realistic pitted structures from virgin fiber structures and then analyze their degradation as the degree of pitting increases. For that purpose, we developed a pitting module within PuMA that creates pits with user-defined geometry (shape, size) and distribution (defect density) on the surface of arbitrary microstructures. In this work, we consider FiberForm microstructures, which are commonly used as the base material for ablative thermal protection systems (TPS). Using the new pitting module, we mimic the evolution of etch pits on FiberForm as it occurs from oxidation in ablative heating environments, by first importing the virgin FiberForm structure from a micrograph scan and then imposing different pitting conditions by varying pit radii and defect densities. We then leverage PuMA’s capabilities to calculate material properties for each structure. The results clearly show the degradation of thermal conductivity and structural integrity as etch pits grow, and furthermore highlight the complex evolution of the surface topology, which results in significant changes of the flowgeometry and chemical gas-surface interactions. Furthermore, a comparison of these changes with the case of shrinking fibers, which has heretofore been the standard for modelling ablation of carbon structures, yields significant differences. For example, we observe the formation of small chunks of fibers as pits grow in size, which could be released into the surrounding flow environment as spallation particles. This motivates us to continue our efforts of modelling pitting as an integral part of the structural degradation of carbon fiber structures in oxidation environments, which will ultimately improve our understanding of failure mechanisms in those materials.

PuMA↗

NASA NTRS1995

Geology and landscape evolution of the Hellas region of Mars

Hellas basin on Mars has been the site of volcanism, tectonism, and modification by fluvial, mass-wasting, and eolian processes over its more than 4-b.y. existence. Our detailed geologic mapping and related studies have resulted in the following new interpretations. The asymmetric distribution of highland massifs and other structures that define the uplifted basin rim suggest a formation of the basin by the impact of a low-angle bolide having a trajectory heading S60E. During the Late Noachian, the basin was infilled, perhaps by lava flows, that were sufficiently thick (greater than 1 km) to produce wrinkle ridges on the fill material and extensional faulting along the west rim of the basin. At about the same time, deposits buried northern Malea Planum, which are interpreted to be pyroclastic flows from Amphitrites and Peneus Paterae on the basis of their degraded morphology, topology, and the application of a previous model for pyroclastic volcanism on Mars. Peneus forms a distinctive caldera structure that indicates eruption of massive volumes of magma, whereas Amphitrites is a less distinct circular feature surrounded by a broad, low, dissected shield that suggests generally smaller volume eruptions. During the Early Hesperian, an approximately 1-to 2km-thick sequence of primarily fined-grained, eolian material was deposited on the floor of Hellas basin. Subsequently, the deposit was deeply eroded, except where armored by crater ejecta, and it retreated as much as 200-300 km along its western margin, leaving behind pedestal craters and knobby outliers of the deposit. Local debris flows within the deposit attest to concentrations of groundwater, perhaps in part brought in by outflow floods along the east rim of the basin. These floods may have deposited approximately 100-200m of sediment, subduing wrinkle ridges in the eastern part of the basin floor. During the Late Hesperian and Amazonian, eolian mantles were emplaced on the basin rim and floor and surrounding highlands. Their subsequent erosion resulted in pitted and etched plains and crater fill, irregular mesas, and pedestal craters. Local evidence occurs for the possible former presence of ground ice or ice sheets approximately 100 km across; however, we disagree with a hypothesis that suggest that the entire south rim and much of the floor of Hellas have been glaciated. Orientations of dune fields and yardangs in lower parts of Hellas basin follow directions of the strongest winds predicted by a recently published general circulation model (GCM). Transient frost and dust splotches in the region are, by contrast, related to the GCM prediction for the season in which the images they appear in were taken.

Tanaka, Kenneth L.↗

NASA NTRSDate not supplied

Thermoplastic Space Point Design (TSPD) Tall Tower Lunar Thermal Analysis

The Thermoplastics Development for Exploration Applications (TDEA) project seeks to advance NASA’s thermoplastic composites capabilities by developing structurally efficient joining solutions for large-scale space structures to support NASA’s future exploration missions. A key objective is to develop and understand advanced thermoplastic joining techniques relevant to space environments and applicable to unitized and/or reconfigurable composite structures. The TDEA project uses NASA Langley’s Tall Lunar Tower (TLT) concept as a target application for the design and development of in-space assembled thermoplastic composites. TLT is a 50-meter-tall tower constructed on the lunar surface near the south pole. The tower’s height at this location on the moon allows for extended durations of incident solar flux which can be used to generate power via photovoltaic arrays. The thermal environment present on lunar south pole represents a challenging environment for any space-based asset. This study provides an overview of the analysis techniques used to determine the temperature extremes, gradients, and timelines of a tall composite tower over a one-year duration at the Shackleton Connecting Ridge. The developed thermal model includes tower and lunar surface elements with anisotropic and temperature-dependent material properties and incorporates a solar vector orbit with time-varying solar flux. Study topics include: a comparison between the effects of simplified lunar surface topologies on thermal results, prediction of surface temperature values versus Lunar Reconnaissance Orbiter (LRO) flight data, and tower structural-thermal deformation.

Lunar↗

NASA NTRS2018

Topological Control of Polystyrene-Silica Core-Shell Microspheres

Controllable surface morphology is requisite across a gamut of processes, industries, and applications. The surface morphology of silica-coated polystyrene microspheres was controllably modified to enable generation of both smooth and bumpy, or raspberry-like, surfaces. Although smooth and raspberry-like silica shells on polystyrene templates have been demonstrated extensively, the method described here used readily available materials to produce radical changes in surface morphology from a single polystyrene template coated in silica through a facile sol-gel reaction processes. Silica shells were deposited via a sol-gel process (using tetraethyl orthosilicate as the silica precursor) onto 1 to 2 m diameter anionic polystyrene spheres, fabricated by emulsifier-free polymerization. By varying of the concentration of silica precursor and ammonium hydroxide catalyst and altering the electrostatic surface interactions via addition of a cationic polymeric brush, an array of surface topologies was generated. The resulting silica shells ranged from 100 to 200 nm in thickness, as measured by calcination of the polystyrene template. Empirical relations between reaction conditions and the resulting silica colloid diameter were utilized to understand the resultant silica shell topology. These results may serve as a guide to generate a versatile platform for research in the multitude of applications where polystyrene-silica core-shell particles are utilized.

Zane A. Grady↗

NASA NTRS2005

Multivariate Parameter Sets for Optimal Synthesis of Compliant Mechanisms

This paper will propose the use of control maps along with discretized elements or meshes in the design parameter set for optimizing compliant mechanisms. The use of control maps will be demonstrated to encode the motion of groups of nodes or control points within a compliant mechanism design with simple mapping rules. The technique will serve as an alternative to increased mesh size or node wandering techniques that have been proposed to increase the number of alternative design shapes that may be considered. As an alternative approach, the proposed control map parameterization has the significant benefit that it minimizes the number of design parameters necessary (parameters increase linearly with the mesh size) in describing a given design making it computationally efficient. A limited number of tiles can produce a map that has a significant effect on the final shape. If the tiles are chosen appropriately, the problems such as material overlap and non-convex mesh elements are avoided automatically. This paper will describe the implementation of these control maps and provide several examples showing their implementation in the compliant mechanism topology synthesis process.

Shibakov, Alex↗

NASA NTRS1992

Solar wind composition from sector boundary crossings and coronal mass ejections

Using the Ion Composition Instrument (ICI) on board the ISEE-3/ICE spacecraft, average abundances of He-4, He-3, O, Ne, Si, and Fe have been determined over extended periods. In this paper the abundances of He-4, O, Ne, Si, and Mg obtained by the ICI in the region of sector boundary crossings (SBCs), magnetic clouds and bidirectional streaming events (BDSs) are compared with the average abundances. Both magnetic clouds and BDSs are associated with coronal mass ejections (CMEs). No variation of abundance is seen to occur at SBCs except for helium, as has already been observed. In CME-related material, the abundance of neon appears to be high and variable, in agreement with recent analysis of spectroscopic observations of active regions. We find that our observations can be correlated with the magnetic topology in the corona.

Ogilvie, K. W.↗