SEARCH · Search NASA

Results for “Total power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1971

Investigation of line-of-sight propagation in dense atmosphere, phase 3, part 1

The investigation of microwave absorption in the 1 to 10 GHz frequency band by the Jovian atmosphere has continued, and an estimate of the strength of signal fading at these frequencies due to layers of turbulence in Jupiter's atmosphere is given. The microwave absorption due to gaseous ammonia is estimated both in terms of a power loss in dB/km, and in total power loss in dB for slant-path communication with a probe at altitudes down to pressures of several tens of atmospheres. The graphs indicate a frequency-squared scaling of the absorption, and appreciable losses at altitudes where the pressure is several atmospheres. An estimate of turbulence strength is given. This may turn out to be quite crude considering the absence of any relevant data. A planetary scaling law which appears to hold reasonably well for Earth to Venus, is extrapolated to Jupiter. No reasonable modifications of the estimate can alter the conclusion that direct-path fading is negligible for pressure regimes up to 20 atm.

Dewolf, D. A.↗

NASA NTRS1972

Drive turbine systems for 20-inch turbofan simulators. 1: Duct turbine design

A study was made to evolve the turbine drive systems for 20-inch turbofan engine simulators. The fan designs used in the simulators included single-stage and two-stage configurations that covered a wide range of rotative speed and power requirement. The objective assumed for the study was to evolve one core turbine design that could drive all of the single-stage fans and, when operated in combination with one duct turbine design, drive all of the two-stage fans. The duct turbine power output is then needed to determine the make-up power required of the core turbine over the range of two-stage fan operating conditions. The duct turbine design analysis is reported and includes the selection of the duct turbine velocity diagram, a description of the blade design, and a determination of its off-design performance. Adjustable stators were found to be quite advantageous to the duct turbine off-design operation. The use of adjustable stators enabled the duct turbine to accommodate fan mass flow at all operating points and caused the duct turbine power output to increase as the total power requirement increased. This in turn resulted in a core turbine make-up power requirement that was not significantly greater than that required for driving the single-stage fans.

Whitney, W. J.↗

NASA NTRS1979

Direct observation of a tangential electric field component at the magnetopause

Results are presented for direct, in situ measurements of the quasi-static electric field at and near the magnetopause, in the magnetosheath, bow shock, and solar wind, obtained by the ISEE-1 satellite. Both the large-scale average electric field and the fine-scale field observed during a magnetopause crossing show the existence of significant tangential electric field components on both sides of the magnetopause. The data in the satellite frame also show significant normal electric field components that point toward the magnetopause on both sides. The observed local level of power dissipation would correspond to a total power of 1 TW, if it existed over the entire front of the magnetopause.

Mozer, F. S.↗

NASA NTRS2004

Performance Evaluation of Fiber Bragg Gratings at Elevated Temperatures

The development of integrated fiber optic sensors for smart propulsion systems demands that the sensors be able to perform in extreme environments. In order to use fiber optic sensors effectively in an extreme environment one must have a thorough understanding of the sensor s limits and how it responds under various environmental conditions. The sensor evaluation currently involves examining the performance of fiber Bragg gratings at elevated temperatures. Fiber Bragg gratings (FBG) are periodic variations of the refractive index of an optical fiber. These periodic variations allow the FBG to act as an embedded optical filter passing the majority of light propagating through a fiber while reflecting back a narrow band of the incident light. The peak reflected wavelength of the FBG is known as the Bragg wavelength. Since the period and width of the refractive index variation in the fiber determines the wavelengths that are transmitted and reflected by the grating, any force acting on the fiber that alters the physical structure of the grating will change what wavelengths are transmitted and what wavelengths are reflected by the grating. Both thermal and mechanical forces acting on the grating will alter its physical characteristics allowing the FBG sensor to detect both temperature variations and physical stresses, strain, placed upon it. This ability to sense multiple physical forces makes the FBG a versatile sensor. This paper reports on test results of the performance of FBGs at elevated temperatures. The gratings looked at thus far have been either embedded in polymer matrix materials or freestanding with the primary focus of this paper being on the freestanding FBGs. Throughout the evaluation process, various parameters of the FBGs performance were monitored and recorded. These parameters include the peak Bragg wavelength, the power of the Bragg wavelength, and total power returned by the FBG. Several test samples were subjected to identical test conditions to allow for statistical analysis of the data. Test procedures, calibrations, and referencing techniques are presented in the paper along with directions for future research.

Juergens, Jeffrey↗

NASA NTRS1995

Steady State Temperature Profile in a Cylinder Heated by Microwaves

A new theory has been developed to calculate the steady state temperature profile in a cylindrical sample positioned along the entire axis of a cylindrical microwave cavity. Temperature profiles where computed for- alumina rods of various radii contained in a cavity excite in one of the TM(sub OnO) modes with n = 1, 2 or 3. Calculations where also performed with a concentric outer cylindrical tube surrounding the rod to investigate hybrid heating. The parameters studies of the sample center and surface temperature where performed as a function of the total power transmitted into the cavity. Also, the total hemispherical emissivity was varied at boundaries of the rod, surrounding tube, and cavity walls. The result are discussed in the context of controlling the average rod temperature and the temperature distribution in the rod during microwave processing.

Jackson, H. W.↗

NASA NTRS1998

Impact of Radiation Hardness and Operating Temperatures of Silicon Carbide Electronics on Space Power System Mass

The effect of silicon carbide (SiC) electronics operating temperatures on Power Management and Distribution (PMAD), or Power Conditioning (PC), subsystem radiator size and mass requirements was evaluated for three power output levels (100 kW(e) , 1 MW(e), and 10 MW(e)) for near term technology ( i.e. 1500 K turbine inlet temperature) Closed Cycle Gas Turbine (CCGT) power systems with a High Temperature Gas Reactor (HTGR) heat source. The study was conducted for assumed PC radiator temperatures ranging from 370 to 845 K and for three scenarios of electrical energy to heat conversion levels which needed to be rejected to space by means of the PC radiator. In addition, during part of the study the radiation hardness of the PC electronics was varied at a fixed separation distance to estimate its effect on the mass of the instrument rated reactor shadow shield. With both the PC radiator and the conical shadow shield representing major components of the overall power system the influence of the above on total power system mass was also determined. As expected, results show that the greatest actual mass savings achieved by the use of SiC electronics occur with high capacity power systems. Moreover, raising the PC radiator temperature above 600 K yields only small additional system mass savings. The effect of increased radiation hardness on total system mass is to reduce system mass by virtue of lowering the shield mass.

Juhasz, Albert J.↗

NASA NTRS1977

Results of closed cycle MHD power generation test with a helium-cesium working fluid

The cross sectional dimensions of the MHD channel in the NASA Lewis closed loop facility were reduced to 3.8 x 11.4 cm. Tests were run in this channel using a helium-cesium working fluid at stagnation pressures of 160,000 n/M2, stagnation temperatures of 2000-2060 K and an entrance Mach number of 0.36. In these tests Faraday open circuit voltages of 200 V were measured which correspond to a Faraday field of 1750 V/M. Power generation tests were run for different groups of electrode configurations and channel lengths. Hall fields up to 1450 V/M were generated. Power extraction per electrode of 183 W and power densities of 1.7 MW/M3 were obtained. A total power output of 2 kW was generated for tests with 14 electrodes. The power densities obtained in this channel represent a factor of 3 improvement over those previously reported for the M = 0.2 channel.

Sovie, R. J.↗

NASA NTRS1939

Tandem Air Propellers

Tests of 2-blade, adjustable-pitch, counter rotating tandem model propellers, adjusted to absorb equal power at maximum efficiency, were made at Stanford University. The characteristics, for 15 degrees, 25 degrees, 35 degrees, and 45 degrees pitch settings at 0.75 R of the forward propeller and for 8-1/2 percent, 15 percent, and 30 percent diameter spacings, were compared with those of 2-blade and 4-blade propellers of the same blade form. The tests showed that the efficiency of the tandem propellers was from 0.5 percent to 4 percent greater than that of a 4-blade propeller and, at the high blade-angle settings, not appreciably inferior to that of a 2-blade propeller. It was found that the rear tandem propeller should be set at a blade angle slightly less than that of the forward propeller to realize the condition of equal power at maximum efficiency. Under this condition the total power absorbed by the tandem propellers was from 3 percent to 9 percent more than that absorbed by the 4-blade propeller and about twice that absorbed by a 2-blade propeller.

Lesley, E P↗

NASA NTRS1999

Power Management in Regenerative Life Support Systems

Effective management of power can reduce the cost of launch and operation of regenerative life support systems. Variations in power may be quite severe and may manifest as surges or spikes, While the power plant may have some ability to deal with these variations, with batteries for example, over-capacity is expensive and does nothing to address the fundamental issue of excessive demand. Because the power unit must be sized to accommodate the largest demand, avoiding power spikes has the potential to reduce the required size of the power plant while at the same time increasing the dependability of the system. Scheduling of processors can help to reduce potential power spikes. However, not all power-consuming equipment is easily scheduled. Therefore, active power management is needed to further decrease the risk of surges or spikes. We investigate the use of a hierarchical scheme to actively manage power for a model of a regenerative life support system. Local level controllers individually determine subsystem power usage. A higher level controller monitors overall system power and detects surges or spikes. When a surge condition is detected, the higher level controller conducts an 'auction' and describes subsystem power usage to re-allocate power. The result is an overall reduction in total power during a power surge. The auction involves each subsystem making a 'bid' to buy or sell power based on local needs. However, this re-allocation cannot come at the expense of life support function. To this end, participation in the auction is restricted to those processes meeting certain tolerance constraints. These tolerances represent acceptable limits within which system processes can be operated. We present a simulation model and discuss some of our results.

Crawford, Sekou↗

NASA NTRS2007

Measuring Radiofrequency and Microwave Radiation from Varying Signal Strengths

This viewgraph presentation discusses the process of measuring radiofrequency and microwave radiation from various signal strengths. The topics include: 1) Limits and Guidelines; 2) Typical Variable Standard (IEEE) Frequency Dependent; 3) FCC Standard 47 CFR 1.1310; 4) Compliance Follows Unity Rule; 5) Multiple Sources Contribute; 6) Types of RF Signals; 7) Interfering Radiations; 8) Different Frequencies Different Powers; 9) Power Summing - Peak Power; 10) Contribution from Various Single Sources; 11) Total Power from Multiple Sources; 12) Are You Out of Compliance?; and 13) In Compliance.

Davis, Bette↗

NASA NTRS1937

Tandem Air Propellers

Tests of 2-blade, adjustable-pitch, counterrotating tandem model propellers, adjusted to absorb equal power at maximum efficiency, were made at Stanford University. The characteristics, for 15 degrees, 25 degrees, 35 degrees, and 45 degrees pitch settings at 0.75 R of the forward propeller and for 8 1/2%, 15% and 30% diameter spacings, were compared with those of 2-blade and 4-blade propellers of the same blade form. The tests showed that the efficiency of the tandem propellers was from 0.5% to 4% greater than that of a 4-blade propeller and, at the high pitch settings, not appreciable inferior to that of a 2-blade propeller. It was found that the rear tandem propeller should be set at a pitch angle slightly less than that of the forward propeller to realize the condition of equal power at maximum efficiency. Under this condition the total power absorbed by the tandem propellers was from 3% to 9% more than that absorbed by the 4-blade propeller and about twice that absorbed by a 2-blade propeller.

Lesley, E.P.↗

NASA NTRS2020

Cathode & Electromagnet Qualification Status and Power Processing Unit Development Update for the Ascendant Sub-kW Transcelestial Electric Propulsion System

A review of the component-level flight qualification efforts and power processing unit development status of the Ascendant Sub-kW Transcelestial Electric Propulsion System (ASTRAEUS) program is presented. Component-level qualification efforts were undertaken for the system’s ultra-compact heaterless LaB6 hollow cathode and electromagnets, both of which employ designs bespoke to ASTRAEUS, as they represent the highest failure risks for the thruster. Through parallel long-duration wear and ignition tests, the ASTRAEUS cathode demonstrated invariant discharge performance over more than 5000 h of operation at its maximum operating current of 4 A and demonstrated more than 25,000 ignition cycles. The ASTRAEUS electromagnets completed their environmental qualification through a demonstration of more than 1200 deep thermal cycles with no indication of coil degradation (the test articles previously completed qualification-level vibration and shock testing). ASTRAEUS’s prototype power processing unit has demonstrated more than 92% total power conversion efficiency and class-leading power density & specific power density of 4.5 W/cm3 & 1670 W/kg, respectively. The various power converters found in the ASTRAEUS power processing unit are reviewed with a focus on the methods by which such high performance was achieved.

Conversano, Ryan W.↗

NASA NTRS2010

Solar Energy Systems for Lunar Oxygen Generation

An evaluation of several solar concentrator-based systems for producing oxygen from lunar regolith was performed. The systems utilize a solar concentrator mirror to provide thermal energy for the oxygen production process. Thermal energy to power a Stirling heat engine and photovoltaics are compared for the production of electricity. The electricity produced is utilized to operate the equipment needed in the oxygen production process. The initial oxygen production method utilized in the analysis is hydrogen reduction of ilmenite. Utilizing this method of oxygen production a baseline system design was produced. This baseline system had an oxygen production rate of 0.6 kg/hr with a concentrator mirror size of 5 m. Variations were performed on the baseline design to show how changes in the system size and process (rate) affected the oxygen production rate. An evaluation of the power requirements for a carbothermal lunar regolith reduction reactor has also been conducted. The reactor had a total power requirement between 8,320 to 9,961 W when producing 1000 kg/year of oxygen. The solar concentrator used to provide the thermal power (over 82 percent of the total energy requirement) would have a diameter of less than 4 m.

Colozza, Anthony J.↗

NASA NTRS1977

Results of closed cycle MHD power generation tests with a helium-cesium working fluid

The cross-sectional dimensions of the MHD channel in the NASA Lewis closed loop facility have been reduced to 3.8 x 11.4 cm. Tests were run in this channel using a helium-cesium working fluid at stagnation pressures of 1.6 x 10 to the 5th N/sq m, stagnation temperatures of 2000-2060 K and an entrance Mach number of 0.36. In these tests Faraday open circuit voltages of 200 V were measured which correspond to a Faraday field of 1750 V/m. Power generation tests were run for different groups of electrode configurations and channel lengths. Hall fields up to 1450 V/m were generated. Power extraction per electrode of 183 W and power densities of 1.7 MW/cu m have been obtained. A total power output of 2 kW was generated for tests with 14 electrodes. The power densities obtained in this channel represent a factor of 3 improvement over those reported for the m = 0.2 channel at the last EAM Symposium.

Sovie, R. J.↗

NASA NTRS1981

A failure mechanism in adaptive arrays

The steady-state behavior of an adaptive array is considered and the degradation of its output SNR in the presence of jammers is analyzed. It is shown that for given incident powers (of jammers and signal), there are geometric configurations of the sources exciting the array for which the SNR degradation is much more pronounced than for other configurations. This result is proved for the case where the thermal noise power of each array receiver is negligible compared to the total power intercepted by the array from each jammer. The result is general, being valid for an array of n arbitrary antennae in an arbitrary three-dimensional configuration. It is stated in terms of linear dependence relationships among the n-dimensional vectors that describe the effects of the sources on the array.

Zohar, S.↗

NASA NTRS2015

Development and Short-Range Testing of a 100 kW Side-Illuminated Millimeter-Wave Thermal Rocket

The objective of the phase described here of the Millimeter-Wave Thermal Launch System (MTLS) Project was to launch a small thermal rocket into the air using millimeter waves. The preliminary results of the first MTLS flight vehicle launches are presented in this work. The design and construction of a small thermal rocket with a planar ceramic heat exchanger mounted along the axis of the rocket is described. The heat exchanger was illuminated from the side by a millimeter-wave beam and fed propellant from above via a small tank containing high pressure argon or nitrogen. Short-range tests where the rocket was launched, tracked, and heated with the beam are described. The rockets were approximately 1.5 meters in length and 65 millimeters in diameter, with a liftoff mass of 1.8 kilograms. The rocket airframes were coated in aluminum and had a parachute recovery system activated via a timer and Pyrodex. At the rocket heat exchanger, the beam distance was 40 meters with a peak power intensity of 77 watts per square centimeter. and a total power of 32 kilowatts in a 30 centimeter diameter circle. An altitude of approximately 10 meters was achieved. Recommendations for improvements are discussed.

Bruccoleri, Alexander↗

NASA NTRS1991

High-power and high-spatial-coherence broad-area power amplifier

A broad-area AlGaAs amplifier operating CW has delivered 425 mW of total power with 342 mW in a single lobe diverging at 1.02 times the diffraction limit (FWHM 0.483 deg, 87.4-micron actual aperture) for a master oscillator input power of 70 mW. The spatial coherence of the amplifier output is 0.97, and the mutual spatial coherence between the oscillator and the amplifier is 0.96.

Andrews, John R.↗

NASA NTRS1978

Far-infrared observations of H II regions in M33

Three H II regions in M33, namely, IC 133, NGC 595, and NGC 604, have been observed at far-infrared wavelengths. Only NGC 604, the strongest radio source of the three, was detected. The far-infrared radiation appears to be thermal emission from dust. The amount of dust known to be present in NGC 604 from comparison of optical and radio data is sufficient to account for the observed far-infrared emission. The total power radiated in the far-infrared is comparable to the total luminosity of the exciting stars of the H II region.

Gatley, I.↗