Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transition Detection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Obtaining the Mass and Radius of Extra-Solar Giant Planets

The scientific utility and feasibility of detecting transits of the 9 known extrasolar planets is explored. A transit of a solar-like star by a Jupiter mass planet produces a 1% decrease in the amount of light received from the star. Transit observation will remove the ambiguity in the measurement of the planetary mass inherent in the radial velocity method and confirm the planet's existence. The 9 known planets have a 33% chance of producing at least one observable transit. Additional extrasolar planet detections from the radial velocity surveys will increase this probability to greater than 90%. The radius of the planet can be determined by the fractional decrease in light received during transit. The mass and radius may distinguish rocky or gas giant planets from brown dwarfs. The probability of detection, the transit signal size and duration, and predictions of the transit times (including errors) are calculated for circular and elliptical orbits. Observational limits are investigated and it is shown that small telescopes and existing detectors are adequate enough to achieve the 0.1% photometry necessary to detect transits of the known extrasolar planets.

Castellano, Tim↗
NASA NTRS1989

In-flight boundary-layer transition measurements on a swept wing

Flight tests were conducted at three different altitudes to detect transition on a smoothed test region of a swept-wing business jet wing using surface hot-film sensors and sublimating chemicals. Strong influence of sweep angle on transition location was observed when the aircraft was flown at some sideslip conditions to simulate changes in effective wing sweep angle. No effects of engine noise on transition were measured when different engine power settings were used. Flight instrumentation and ground data analysis techniques are described. Correlation was obtained between the hot-film sensor signals and sublimating chemicals for transition detection. Crossflow vortices were observed for one flight condition. Results of analyzed data for various flight-test conditions are presented.

Ahmed, Anwar↗
NASA NTRS2016

Boundary-Layer Detection at Cryogenic Conditions Using Temperature Sensitive Paint Coupled with a Carbon Nanotube Heating Layer

Detection of flow transition on aircraft surfaces and models can be vital to the development of future vehicles and computational methods for evaluating vehicle concepts. In testing at ambient conditions, IR thermography is ideal for this measurement. However, for higher Reynolds number testing, cryogenic facilities are often used, in which IR thermography is difficult to employ. In these facilities, temperature sensitive paint is an alternative with a temperature step introduced to enhance the natural temperature change from transition. Traditional methods for inducing the temperature step by changing the liquid nitrogen injection rate often change the tunnel conditions. Recent work has shown that adding a layer consisting of carbon nanotubes to the surface can be used to impart a temperature step on the model surface with little change in the operating conditions. Unfortunately, this system physically degraded at 130 K and lost heating capability. This paper describes a modification of this technique enabling operation down to at least 77 K, well below the temperature reached in cryogenic facilities. This is possible because the CNT layer is in a polyurethane binder. This was tested on a Natural Laminar Flow model in a cryogenic facility and transition detection was successfully visualized at conditions from 200 K to 110 K. Results were also compared with the traditional temperature step method.

Goodman, Kyle Z.↗
NASA NTRSDate not supplied

Transition Measurements on the SWiFT Model in the National Transonic Facility

Boundary layer transition locations on the Swept Wing Flow Test (SWiFT) Hybrid Wing Body model were measured in the National Transonic Facility (NTF) at the NASA Langley Research Center using several different methods. These methods include sublimating chemical flow visualization for a limited number of low Reynolds number conditions, as well as mean static pressure and dynamic pressure measurements. Results are presented for a range of conditions in the NTF, demonstrating Mach and Reynolds number effects. The transition front locations obtained from the different techniques agree well. A variation of the static pressure transition detection method is described in which continuous angle of attack polars are performed. This approach enables detection of the transition front at more challenging (high Reynolds number) conditions than is possible with sparser data from pitch-pause angle-of-attack polars. The trip dot effectiveness is also verified using all of the available diagnostics. Additionally, low Reynolds number results are compared with those acquired on the same model at the Aircraft Research Association (ARA) facility, and these results show good agreement overall, suggesting similar freestream flow quality conditions of the two facilities.

National Transonic Facility↗
NASA NTRSDate not supplied

Transition Measurements on the SWiFT Model in the National Transonic Facility

Boundary layer transition locations on the Swept Wing Flow Test (SWiFT) Hybrid Wing Body model were measured in the National Transonic Facility (NTF) at the NASA Langley Research Center using several different methods. These methods include sublimating chemical flow visualization for a limited number of low Reynolds number conditions, as well as mean static pressure and dynamic pressure measurements. Results are presented for a range of conditions in the NTF, demonstrating Mach and Reynolds number effects. The transition front locations obtained from the different techniques agree well. A variation of the static pressure transition detection method is described in which continuous angle of attack polars are performed. This approach enables detection of the transition front at more challenging (high Reynolds number) conditions than is possible with sparser data from pitch-pause angle-of-attack polars. The trip dot effectiveness is also verified using all of the available diagnostics. Additionally, low Reynolds number results are compared with those acquired on the same model at the Aircraft Research Association (ARA) facility, and these results show good agreement overall, suggesting similar freestream flow quality conditions of the two facilities.

National Transonic Facility↗
NASA NTRS1999

Unified Model Deformation and Flow Transition Measurements

The number of optical techniques that may potentially be used during a given wind tunnel test is continually growing. These include parameter sensitive paints that are sensitive to temperature or pressure, several different types of off-body and on-body flow visualization techniques, optical angle-of-attack (AoA), optical measurement of model deformation, optical techniques for determining density or velocity, and spectroscopic techniques for determining various flow field parameters. Often in the past the various optical techniques were developed independently of each other, with little or no consideration for other techniques that might also be used during a given test. Recently two optical techniques have been increasingly requested for production measurements in NASA wind tunnels. These are the video photogrammetric (or videogrammetric) technique for measuring model deformation known as the video model deformation (VMD) technique, and the parameter sensitive paints for making global pressure and temperature measurements. Considerations for, and initial attempts at, simultaneous measurements with the pressure sensitive paint (PSP) and the videogrammetric techniques have been implemented. Temperature sensitive paint (TSP) has been found to be useful for boundary-layer transition detection since turbulent boundary layers convect heat at higher rates than laminar boundary layers of comparable thickness. Transition is marked by a characteristic surface temperature change wherever there is a difference between model and flow temperatures. Recently, additional capabilities have been implemented in the target-tracking videogrammetric measurement system. These capabilities have permitted practical simultaneous measurements using parameter sensitive paint and video model deformation measurements that led to the first successful unified test with TSP for transition detection in a large production wind tunnel.

Burner, Alpheus W.↗
NASA NTRS2001

Detection of Terrestrial Planets Using Transit Photometry

Transit photometry detection of planets offers many advantages: an ability to detect terrestrial size planets, direct determination of the planet's size, applicability to all main-sequence stars, and a differential brightness change of the periodic signature being independent of stellar distance or planetary orbital semi-major axis. Ground and space based photometry have already been successful in detecting transits of the giant planet HD209458b. However, photometry 100 times better is required to detect terrestrial planets. We present results of laboratory measurements of an end-to-end photometric system incorporating all of the important confounding noise features of both the sky and a space based photometer including spacecraft jitter. In addition to demonstrating an instrumental noise of less than 10 ppm (an Earth transit of a solar-like star is 80 ppm), the brightnesses of individual stars were dimmed to simulate Earth-size transit signals. These 'transits' were reliably detected as part of the tests.

Koch, David↗
NASA NTRS1984

Natural laminar flow flight experiments on a swept-wing business jet

Flight test experiments have been conducted to measure the extent and nature of laminar flow on a smoothed test region of a swept-wing business jet. Surface hot film anemometers and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Instrumentation techniques and problems are presented. Correlation was obtained between the hot film and sublimating chemicals for transition detection. Taylor-Goertler vortices were observed for some flight conditions. Boundary layer stability analysis is being conducted using measured pressure distributions to determine the correlation possible for transition prediction on swept wings.

Wentz, W. H., Jr.↗
NASA NTRS1989

Comparisons of boundary-layer transition measurement techniques in the Langley Unitary Plan wind tunnel

Four different boundary-layer transition detection techniques, namely liquid crystals, very thin hot films, IR photography, and an optical interferometer, were compared using the same flat plate model for the same tunnel conditions. The comparisons, conducted at NASA-Langley, involved not only their sensitivity to transition but also their ease of use. The thin films, as expected, gave excellent quantitative information and were used as the standard for evaluating the other techniques. Both the liquid crystals and IR photography were able to detect transition before the boundary-layer intermittency factor had reached 50 percent. The optical interferometer was unsuccessful. Conditions sampled included a range of Mach numbers from 1.5 to 2.5 and unit Reynolds numbers from 1.0 to 4.0 million/foot.

Hall, R. M.↗
NASA NTRS1985

Further results of natural laminar flow flight test experiments

Flight test experiments were conducted to measure the extent and nature of natural laminar flow on a smoothed test region of a swept-wing business jet wing. Surface hot film anemometry and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Engine noise was monitored by a microphone attached to the wing surface to study possible acoustic effects on stability of the laminar boundary layer. Side-slip conditions were flown to simulate changes in effective wing sweep. Flight instrumentation and ground data analysis techniques and a method for measuring intermittency of turbulence are described. Correlation was obtained between the hot film gage signals and chemicals for transition detection. Cross-flow vortices were observed for some flight conditions. Results of spectral and statistical analysis of the hot film signals for various flight test conditions are presented.

Wentz, W. H., Jr.↗
NASA NTRS1997

In-Flight Flow Visualization Using Infrared Thermography

The feasibility of remote infrared thermography of aircraft surfaces during flight to visualize the extent of laminar flow on a target aircraft has been examined. In general, it was determined that such thermograms can be taken successfully using an existing airplane/thermography system (NASA Dryden's F-18 with infrared imaging pod) and that the transition pattern and, thus, the extent of laminar flow can be extracted from these thermograms. Depending on the in-flight distance between the F-18 and the target aircraft, the thermograms can have a spatial resolution of as little as 0.1 inches. The field of view provided by the present remote system is superior to that of prior stationary infrared thermography systems mounted in the fuselage or vertical tail of a subject aircraft. An additional advantage of the present experimental technique is that the target aircraft requires no or minimal modifications. An image processing procedure was developed which improves the signal-to-noise ratio of the thermograms. Problems encountered during the analog recording of the thermograms (banding of video images) made it impossible to evaluate the adequacy of the present imaging system and image processing procedure to detect transition on untreated metal surfaces. The high reflectance, high thermal difussivity, and low emittance of metal surfaces tend to degrade the images to an extent that it is very difficult to extract transition information from them. The application of a thin (0.005 inches) self-adhesive insulating film to the surface is shown to solve this problem satisfactorily. In addition to the problem of infrared based transition detection on untreated metal surfaces, future flight tests will also concentrate on the visualization of other flow phenomena such as flow separation and reattachment.

vanDam, C. P.↗
NASA NTRS1996

A matched filter method for ground-based sub-noise detection of terrestrial extrasolar planets in eclipsing binaries: application to CM Draconis

The photometric detection of extrasolar planets by transits in eclipsing binary systems can be significantly improved by cross-correlating the observational light curves with synthetic models of possible planetary transit features, essentially a matched filter approach. We demonstrate the utility and application of this transit detection algorithm for ground-based detections of terrestrial-sized (Earth-to-Neptune radii) extrasolar planets in the dwarf M-star eclipsing binary system CM Draconis. Preliminary photometric observational data of this system demonstrate that the observational noise is well characterized as white and Gaussian at the observational time steps required for precision photometric measurements. Depending on planet formation scenarios, terrestrial-sized planets may form quite close to this low-luminosity system. We demonstrate, for example, that planets as small as 1.4 Earth radii with periods on the order of a few months in the CM Draconis system could be detected at the 99.9% confidence level in less than a year using 1-m class telescopes from the ground. This result contradicts commonly held assumptions limiting present ground-based efforts to, at best, detections of gas giant planets after several years of observation. This method can be readily extended to a number of other larger star systems with the utilization of larger telescopes and longer observing times. Its extension to spacecraft observations should also allow the determination of the presence of terrestrial-sized planets in nearly 100 other known eclipsing binary systems.

NASA Discipline Number 52-10↗
NASA NTRS2018

Kepler Data Validation I: Architecture, Diagnostic Tests, and Data Products for Vetting Transiting Planet Candidates

The Kepler Mission was designed to identify and characterize transiting planets in the Kepler Field of View and to determine their occurrence rates. Emphasis was placed on identification of Earth-size planets orbiting in the Habitable Zone of their host stars. Science data were acquired for a period of four years. Long-cadence data with 29.4 min sampling were obtained for approx. 200,000 individual stellar targets in at least one observing quarter in the primary Kepler Mission. Light curves for target stars are extracted in the Kepler Science Data Processing Pipeline, and are searched for transiting planet signatures. A Threshold Crossing Event is generated in the transit search for targets where the transit detection threshold is exceeded and transit consistency checks are satisfied. These targets are subjected to further scrutiny in the Data Validation (DV) component of the Pipeline. Transiting planet candidates are characterized in DV, and light curves are searched for additional planets after transit signatures are modeled and removed. A suite of diagnostic tests is performed on all candidates to aid in discrimination between genuine transiting planets and instrumental or astrophysical false positives. Data products are generated per target and planet candidate to document and display transiting planet model fit and diagnostic test results. These products are exported to the Exoplanet Archive at the NASA Exoplanet Science Institute, and are available to the community. We describe the DV architecture and diagnostic tests, and provide a brief overview of the data products. Transiting planet modeling and the search for multiple planets on individual targets are described in a companion paper. The final revision of the Kepler Pipeline code base is available to the general public through GitHub. The Kepler Pipeline has also been modified to support the Transiting Exoplanet Survey Satellite (TESS) Mission which is expected to commence in 2018.

data analysis↗
NASA NTRS1996

Detectability of the Reflection Signal from Inner Planets

Mayor and Queloz (1996) and Marcy and Butler (1996) have found massive planets with orbital periods Tp=approx.4 days around two solar-like stars (51 Pegasi and v Andromeda). These planets are most likely similar in size and composition to the gas giants in our solar system (Burrows et al 1996). Based on this expectation and assuming the same albedo as Jupiter, we examined the feasibility of searching for similar planets with a dedicated space-based 1-m telescope. The Kepler mission will survey approximately 70,000 main-sequence dwarf stars from 9 to 14 mag continuously for four years to detect transiting Earthlike planets. Based on the detection statistics of Marcy and Butler, we expect to detect 1400 inner-orbit giant planets. Such planets in a much wider range of orbital inclinations (i) will produce nearly sinusoidal modulations of the star light flux due to the varying planetary phases. The relative signal amplitudes are of order 2x10(exp -5) and decrease as Tp(exp 4/3) for i >> 0deg. We estimated the expected signal to noise ratio (SNR) using the solar irradiance measurements from the ACRIM 1 experiment along with expected shot and detector noises. The figure shows SNR as a function of Tp for a 12 mag star, and indicates the planet radius required for detection. The survey will be sensitive to planets with periods from 12 hr to approx.8 days at the 6 sigma level.

Borucki, W. J.↗
NASA NTRS2000

Kepler Mission: End-to-End System Demonstration

A test facility has been constructed to demonstrate the capability of differential ensemble photometry to detect transits of Earth-size planets orbiting solar-like stars. The main objective is to determine the effects of various noise sources on the capability of a CCD photometer to maintain a system relative precision of 1 x $10^(-5)$ for mv = 12 stars in the presence of system-induced noise sources. The facility includes a simulated star field, fast optics to simulate the telescope, a thinned back-illuminated CCD similar to those to be used on the spacecraft and computers to perform the onboard control, data processing and extraction. The test structure is thermally and mechanically isolated so that each source of noise can be introduced in a controlled fashion and evaluated for its contribution to the total noise budget. The effects of pointing errors or a changing thermal environment are imposed by piezo-electric devices. Transits are injected by heating small wires crossing apertures in the star plate. Signals as small as those from terrestrial-size transits of solar-like stars are introduced to demonstrate that such planets can be detected under realistic noise conditions. Examples of imposing several noise sources and the resulting detectabilities are presented. These show that a differential ensemble photometric approach CCD photometer can readily detect signals associated with Earth-size transits.

Borucki, William↗
NASA NTRS1993

Effects of an aft facing step on the surface of a laminar flow glider wing

A motor glider was used to perform a flight test study on the effects of aft facing steps in a laminar boundary layer. This study focuses on two dimensional aft facing steps oriented spanwise to the flow. The size and location of the aft facing steps were varied in order to determine the critical size that will force premature transition. Transition over a step was found to be primarily a function of Reynolds number based on step height. Both of the step height Reynolds numbers for premature and full transition were determined. A hot film anemometry system was used to detect transition.

Sandlin, Doral R.↗
NASA NTRS2003

The Kepler Mission: A Search for Terrestrial Planets - Development Status

We have embarked on a mission to detect terrestrial planets. The space mission has been optimized to search for earth-size planets (0.5 to 10 earth masses) in the habitable zone (HZ) of solar-like stars. Given this design, the mission will necessarily be capable of not only detecting Earth analogs, but a wide range of planetary types and characteristics ranging from Mercury-size objects with orbital periods of days to gas-giants in decade long orbits that have undeniable signatures even with only one transit detected. The mission is designed to survey the full range of spectral-type dwarf stars. The approach is to detect the periodic signal of transiting planets. Three or more transits of a star exceeding a combined threshold of eight sigma with a statistically consistent period, brightness change and duration provide a rigorous method of detection. From the relative brightness change the planet size can be calculated. From the period the orbital size can be calculated and its location relative to the HZ determined. Presented here are: the mission goals, the top level system design requirements derived from these goals that drive the flight system design, a number of the trades that have lead to the mission concept, expected photometric performance dependence on stellar brightness and spectral type based on the system 'noise tree' analysis. Updated estimates are presented of the numbers of detectable planets versus size, orbit, stellar spectral type and distances based on a planet frequency hypothesis. The current project schedule and organization are given.

Koch, David↗
NASA NTRS2021

TOI-674b: An oasis in the desert of exo-Neptunes transiting a nearby M dwarf

Context. The NASA mission TESS is currently doing an all-sky survey from space to detect transiting planets around bright stars. As part of the validation process, the most promising planet candidates need to be confirmed and characterized using follow-up observations. Aims. In this article, our aim is to confirm the planetary nature of the transiting planet candidate TOI-674b using spectroscopic and photometric observations. Methods. We use TESS, Spitzer, ground-based light curves, and HARPS spectrograph radial velocity measurements to establish the physical properties of the transiting exoplanet candidate TOI-674b. We perform a joint fit of the light curves and radial velocity time series to measure the mass, radius, and orbital parameters of the candidate. Results. We confirm and characterize TOI-674b, a low-density super-Neptune transiting a nearby M dwarf. The host star (TIC 158588995, V = 14.2 mag, J = 10.3 mag) is characterized by its M2V spectral type with M⋆ = 0.420 ± 0.010 Mꙩ, R⋆ = 0.420 ± 0.013 Rꙩ, and T(eff) = 3514 ± 57 K; it is located at a distance d = 46.16 ± 0.03 pc. Combining the available transit light curves plus radial velocity measurements and jointly fitting a circular orbit model, we find an orbital period of 1.977143 ± 3 × 10^(−6) days, a planetary radius of 5.25 ± 0.17 Rꚛ, and a mass of 23.6 ± 3.3 Mꚛ implying a mean density of ρp =0.91 ± 0.15 g/cu. cm. A non-circular orbit model fit delivers similar planetary mass and radius values within the uncertainties. Given the measured planetary radius and mass, TOI-674b is one of the largest and most massive super-Neptune class planets discovered around an M-type star to date. It is found in the Neptunian desert, and is a promising candidate for atmospheric characterization using the James Webb Space Telescope.

F. Murgas↗