Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transitional Flight”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Some anomalies between wind tunnel and flight transition results

A review of environmental disturbance influence and boundary layer transition measurements on a large collection of reference sharp cone tests in wind tunnels and of recent transonic-supersonic cone flight results have previously demonstrated the dominance of free-stream disturbance level on the transition process from the beginning to end. Variation of the ratio of transition Reynolds number at onset-to-end with Mach number has been shown to be consistently different between flight and wind tunnels. Previous correlations of the end of transition with disturbance level give good results for flight and large number of tunnels, however, anomalies occur for similar correlation based on transition onset. Present cone results with a tunnel sonic throat reduced the disturbance level by an order of magnitude with transition values comparable to flight.

Harvey, W. D.↗
NASA NTRS1975

Flight transition data for angles of attack at Mach 22 with correlations of the data

Boundary-layer transition data for angles of attack from 2.5 to 47 deg from a flight experiment with a cone that reentered at angles of attack up to 75 deg were analyzed and their local flow conditions are presented. The transition data were obtained from both acoustic and electrostatic sensors. The data from the acoustic and electrostatic sensors were correlated by use of three different sets of correlating parameters. For each set of correlating parameters, the transitional and turbulent data from the acoustic and electrostatic sensors were plotted separately. Each of the correlations was compared with a linear curve fit of previous cone-flight data at near zero angle of attack. Results indicate that the data from acoustic sensors falls below the linear curve fits to the flight data and indicates the sensitivity of the sensors. It is shown that the transition data from the electrostatic sensors tends to scatter much more than the data from the acoustic sensors. However, the data from the electrostatic sensors tends to scatter about the linear curve fits based on previous flight data.

Johnson, C. B.↗
NASA NTRS2012

Tile Surface Thermocouple Measurement Challenges from the Orbiter Boundary Layer Transition Flight Experiment

Hypersonic entry flight testing motivated by efforts seeking to characterize boundary layer transition on the Space Shuttle Orbiters have identified challenges in our ability to acquire high quality quantitative surface temperature measurements versus time. Five missions near the end of the Space Shuttle Program implemented a tile surface protuberance as a boundary layer trip together with tile surface thermocouples to capture temperature measurements during entry. Similar engineering implementations of these measurements on Discovery and Endeavor demonstrated unexpected measurement voltage response during the high heating portion of the entry trajectory. An assessment has been performed to characterize possible causes of the issues experienced during STS-119, STS-128, STS-131, STS-133 and STS-134 as well as similar issues encountered during other orbiter entries.

Charles H. Campbell↗
NASA NTRS1987

Quasi-steady flight to quasi-steady flight transition in a windshear - Trajectory guidance

The control (via the angle of attack) of the vertical flight of an aircraft taking off at maximum power in a horizontal wind shear with downdraft is investigated analytically. Optimal trajectories to recover the initial path inclination or to recover quasi-steady flight (the relative values of the velocity, path inclination, and angle of attack) are derived using a Chebyshev approach and shown to be nearly identical in the shear but divergent after the shear. These results are then applied to construct a trajectory-guidance control comprising a variable-gamma guidance scheme for the shear trajectory, a constant-gamma guidance scheme for the immediate postshear trajectory, and a constant-rate-of-climb guidance scheme for the aftershear trajectory. Numerical results demonstrating the near-optimal performance of the control are presented in tables and graphs.

Miele, A.↗
NASA NTRSDate not supplied

Reference Command Optimization for the Transition Flight Mode of a Lift plus Cruise Vehicle

Advanced air mobility mainly utilizes vehicles that are capable of vertical takeoff and landing (VTOL) for the simplicity of operation and large-scale deployment. However, VTOL vehicles need specialized trajectory and command design for the transition phase, where the vehicles transition between rotor-borne flight and wing-borne flight. Since VTOL vehicles are commonly designed as over-actuated systems for redundancy, one challenge that arises is actuator ambiguity, where it is unclear how to uniquely command actuators for the VTOL vehicle to track a given trajectory. We propose a method to design optimal reference commands for the transition mode. By formulating an 𝑙 1 -norm cost function on the rotor thrusts of the vehicle, we can achieve economical operation of the rotors such that they only operate when necessary and efficiently utilize the aerodynamics to save energy from reduced rotor actuation. We validate our approach in simulations and show its benefit compared to the commonly used differential flatness-based method.

John L Bullock↗
NASA NTRS1956

Transition-flight Tests of a Model of a Low-wing Transport Vertical-take-off Airplane with Tilting Wing and Propellers

An investigation of the stability and control of a low-wing four-engine transport vertical-take-off airplane during the transition from hovering to normal forward flight has been conducted with a remotely controlled free-flight model. The model had four propellers distributed along the wing with the thrust axes in the wing-chord plane. The wing could be rotated to 90 degrees incidence so that the propeller thrust axes were vertical for hovering flight.

CONTROL, LONGITUDINAL↗
NASA NTRS1973

Some comments on V/STOL wind tunnel testing in the transition flight region

Flow breakdown and flow distortion are discussed as the two limitations to wind tunnel testing of V/STOL models at speeds within or near the transition region. It is shown that a very large wind tunnel would be most useful for research into basic aerodynamic phenomena associated with V/STOL aircraft. The large tunnel will not be able to meet the requirements of all the desired testing of V/STOL models, and smaller existing tunnels will continue to be used. There is need for more work, both experimental and theoretical, to bring about a more correct use of the smaller wind tunnels. The large tunnel would be a most useful tool in this work.

Rae, W. H., Jr.↗
NASA NTRS1985

Computational wing design in support of an NLF variable sweep transition flight experiment

A natural laminar flow outer panel wing glove has been designed for a variable sweep fighter aircraft using state-of-the-art computational techniques. Testing of the design will yield wing pressure and boundary-layer data under actual flight conditions and environment. These data will be used to enhance the understanding of the interaction between crossflow and Tollmien-Schlichting disturbances on boundary-layer transition. The outer wing panel was contoured such that a wide range of favorable pressure gradients could be obtained on the wing upper surface. Extensive computations were performed to support the design effort which relied on two- and three-dimensional transonic design and analysis techniques. A detailed description of the design procedure that evolved during this study is presented. Results on intermediate designs at various stages in the design process demonstrate how the various physical and aerodynamic constraints were integrated into the design. Final results of the glove design analyzed as part of the complete aircraft configuration with a full-potential wing/body analysis code indicate that the aerodynamic design objectives were met.

Waggoner, E. G.↗
NASA NTRS1989

Transition flight experiments on a swept wing with suction

Flight experiments were conducted on a 30 degree swept wing with a perforated leading edge by systematically varying the location and amount of suction over a range of Mach number and Reynolds number. Suction was varied chordwise ahead of the front spar from either the front or rear direction by sealing spanwise perforated strips. Transition from laminar to turbulent flow was due to leading edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth, depending on the test configuration, flight condition, and suction location. A state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility was used to study the boundary layer stability as suction location and magnitude varied. N-factor correlations with transition location were made for various suction configurations.

Maddalon, D. V.↗
NASA NTRS1989

Transition Flight Experiments on a Swept Wing With Suction

Flight experiments were conducted on a 30 degree swept wing with a perforated leading edge by systematically varying the location and amount of suction over a range of Mach number and Reynolds number. Suction was varied chordwise ahead of the front spar from either the front or rear direction by sealing spanwise perforated strips. Transition from laminar to turbulent flow was due to leading edge turbulence contamination or crossflow disturbance growth and/or Tollmien-Schlichting disturbance growth-depending on the test configuration, flight condition, and suction location. A state-of-the-art linear stability theory which accounts for body and streamline curvature and compressibility was used to study the boundary layer stability as suction location and magnitude varied. N-factor correlations with transition location were made for various suction configurations.

Maddalon, D. V.↗
NASA NTRS1988

Quasi-steady flight to quasi-steady flight transition for abort landing in a windshear - Trajectory optimization and guidance

Trajectory optimization and trajectory-guidance problems for abort-landing maneuvers in the presence of low-altitude wind shear are investigated by means of numerical simulations, with a focus on methods designed to achieve quasi-steady flight recovery (final values of the relative velocity, path inclination, and angle of attack equal to those for quasi-steady steepest climb). The derivation of the governing equations is outlined; the modeling techniques are explained; and results for a B-727 transport aircraft approaching a sea-level airfield at temperature 100 F are presented in extensive tables and graphs and characterized in detail. The techniques developed are shown to be effective in restoring the aircraft to stable quasi-steady flight.

Miele, A.↗
NASA NTRS1987

Design and test of an NLF wing glove for the variable-sweep transition flight experiment

Gloves for M = 0.7 and 0.8 design points were computationally designed and analyzed at conditions over the proposed flight test envelope. The resulting computational pressure distributions were analyzed in a boundary layer stability code. These results indicate that the available pressure distributions offer a wide range of combinations of cross flow and Tollmien-Schlichting N-factors. The glove designs along with the baseline configuration were tested in an entry into the National Transonic Facility. Analysis of the force and moment data showed no significant differences in the performance and stability and control characteristics between the baseline and gloved configurations. The rolling moment constraint was met over the entire flight test envelope for the gloved configuration. Pressure distributions for the NTF test confirmed the design pressure distributions were achieved. However, it was decided that with minor modifications to the inboard region of the glove, useful available data could be significantly increased by adding another row of pressure orifices at span station 167.

Waggoner, Ed G.↗