Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tubular design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Design Guidance for High Temperature Concentrating Solar Power Components

This report provides guidance for the design of components for concentrating power facilities operating at high temperatures and undergoing high, secondary thermal stresses relative to the applied primary pressure stress. The design rules were developed for the design of Generation 3 CSP tubular receivers manufactured from Alloy 740H, but are generally applicable to a wide range of component types undergoing similar loads. Part 1 of the report provides procedural design rules for components to be used in conjunction with the 2019 edition of the ASME Boiler & Pressure Vessel Code. Part 2 provides corresponding design data for Alloy 740H. Part 3 of the report is a commentary describing the rationale behind the design rules and the data underlying the design material properties. Finally, Part 4 provides an extensive set of worked sample problems detailing the application of the rules to CSP components.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1975

Evaluation of bead-stiffened metal panels

Potential weight efficiency for bead-stiffened panels has been demonstrated through fabrication and testing. Theoretically optimum design concepts were identified, and small specimens were tested under combined compression, shear, and bending to determine local buckling failure loads and to verify theory. Large optimized panels were then designed and tested under combined loads. Correlation of test data for large circular tubular panels with theory was conservative and consistent, and indicated reliable and acceptable design theory. Tests of fluted tubular panels indicated general instability failures at loads far below the design values due to nonlinear distortions. Further study of the fluted tubular configuration will be required if its potential weight efficiency is to be attained.

Shideler, J. L.↗
NASA NTRS1991

Lightweight, fire-retardant, crashworthy aircraft seat cushioning

A two page discussion of non-aerospace seating applications and the design of NASA's safety seat cushioning (SSC) is presented. The SSC was designed for both safety and comfort in order to replace polyurethane cushioning which is flammable and produces lethal fumes upon combustion. The SSC is composed of advanced fabric reinforced composites and is lightweight, fire-retardent, and crashworthy. The seat design consists of central elliptical tubular spring supports made of fire-resistant and fatigue-durable composites surrounded by a fire-blocking sheath. The cushioning is made crashworthy by incorporating energy-absorbing, viscoelastic layers between the nested, elliptical-hoop springs. The design is intended to provide comfortable seating that meets aircraft-loading requirements without using the conventional polyurethane materials. The designs of an aircraft seat and structural components of the SSC are also presented.

Haslim, Leonard A.↗
NASA NTRS1988

Tubular space truss structure for SKITTER 2 robot

The Skitter 2 is a three legged transport vehicle designed to demonstrate the principle of a tripod walker in a multitude of environments. The tubular truss model of Skitter 2 is a proof of principal design. The model will replicate the operational capabilities of Skitter 2 including its ability to self-right itself. The project's focus was on the use of light weight tubular members in the final structural design. A strong design for the body was required as it will undergo the most intense loading. Triangular geometry was used extensively in the body, providing the required structural integrity and eliminating the need for cumbersome shear panels. Both the basic femur and tibia designs also relied on the strong geometry of the triangle. An intense literature search aided in the development of the most suitable weld techniques, joints, linkages, and materials required for a durable design. The hinge design features the use of spherical rod end bearings. In order to obtain a greater range of mobility in the tibia, a four-bar linkage was designed which attaches both to the femur and the tibia. All component designs, specifically the body, femur, and the tibia were optimized using the software package IDEAS 3.8A Supertab. The package provided essential deformation and stress analysis information on each component's design. The final structure incurred only a 0.0544 inch deflection in a maximum (worst case) loading situation. The highest stress experienced by any AL6061-T6 tubular member was 1920 psi. The structural integrity of the final design facilitated the use of Aluminum 6061-T6 tubing. The tubular truss structure of Skitter 2 is an effective and highly durable design. All facets of the design are structurally sound and cost effective.

Beecham, Richard↗
NASA NTRS1992

Hot fire test results of subscale tubular combustion chambers

Advanced, subscale, tubular combustion chambers were built and test fired with hydrogen-oxygen propellants to assess the increase in fatigue life that can be obtained with this type of construction. Two chambers were tested: one ran for 637 cycles without failing, compared to a predicted life of 200 cycles for a comparable smooth-wall milled-channel liner configuration. The other chamber failed at 256 cycles, compared to a predicted life of 118 cycles for a comparable smooth-wall milled-channel liner configuration. Posttest metallographic analysis determined that the strain-relieving design (structural compliance) of the tubular configuration was the cause of this increase in life.

Kazaroff, John M.↗
NASA NTRS1995

Low-cost tubular antenna deployer for WISP-2

A new tubular boom deployment mechanism has been designed, built, and flown as part of the second Waves In Space Program (WISP-2) through Cornell University. For this program, two booms were needed to form a dipole antenna but existing units were found to be too complicated and costly. A low-cost alternative was developed which combined flight-proven tubular boom technology with a new support and deployment mechanism. The simplicity of this new design was a major factor in providing a highly reliable and cost-effective system.

Warden, Robert M.↗
NASA NTRS1992

Quick-connect fasteners for assembling devices in space

A quick-connect fastener of a relatively-simple straightforward design is arranged with a tubular body adapted to be engaged against an attachment fitting in coincidental alignment with an opening in that fitting. A tubular collet having flexible finger projecting from its forward end is arranged in the fastener body to be shifted forwardly by an elongated expander member coaxially arranged within the tubular collet for advancing the collet fingers into the opening in the attachment fitting. Biasing means are arranged between the elongated expander member and a rotatable actuator which is threadedly mounted within the tubular collet so as to be rotated for urging the expander member into engagement with the collet fingers. A first coupling member is arranged on the rotatable actuator to be accessible from outside of the fastener so that a second coupling member on the distal end of a flexible shaft can be introduced into the fastener body and coupled to the first coupling member to enable a typical actuating tool coupled to the shaft outside of the fastener body to be operated for advancing the outwardly-enlarged ends of the collet fingers into the opening in the attachment fitting and thereafter rotating the actuator member to expand the fingers to that attachment fitting. Upon expansion of the collet fingers, the biasing means impose a biasing force on the expander to releasably retain the fingers in their latching positions.

Wesselski, Clarence J.↗
NASA NTRS1993

Quick-connect fasteners for assembling devices in space

A quick-connect fastener of a relatively-simple straightforward design is arranged with a tubular body adapted to be engaged against an attachment fitting in coincidental alignment with an opening in that fitting. A tubular collet having flexible fingers projecting from its forward end is arranged in the fastener body to be shifted forwardly by an elongated expander member coaxially arranged within the tubular collet for advancing the collet fingers into the opening in the attachment fitting. Biasing means are arranged between the elongated expander member and a rotatable actuator which is threadedly mounted within the tubular collet so as to be rotated for urging the expander member into engagement with the collet fingers. A first coupling member is arranged on the rotatable actuator to be accessible from outside of the fastener so that a second coupling member on the distal end of a flexible shaft can be introduced into the fastener body and coupled to the first coupling member to enable a typical actuating tool coupled to the shaft outside of the fastener body to be operated for advancing the outwardly-enlarged ends of the collet fingers into the opening in the attachment fitting and thereafter rotating the actuator member to expand the fingers within the opening for releasably latching the fastener to that attachment fitting. Upon expansion of the collet fingers, the biasing means impose a biasing force on the expander to releasably retain the fingers in their latching positions.

Evenson, Erik E.↗
NASA NTRSDate not supplied

Structural Architectures for Self-Erecting Lunar Towers

The load carrying performance for deployable lunar tower architectures utilizing thin-ply composite booms are parametrically evaluated in this paper. These self-erecting towers support a communications and sensor platform on the lunar surface. The primary design consists of the Corrugated Rollable Tubular Boom (COROTUB) acting as the primary mast of the tower which supports the payload tip mass. Guy wires connecting the boom tip to spreader bars attached at the base deployer serve to correct any lateral eccentricities and provide dimensional stability. The analysis compares the maximum tip mass that this primary design can carry relative to a reference design that does not contain any guy wires or spreader bars. The results provide insights into whether the additional system mass and complexity associated with the cable-stayed design is worth the increased payload mass that can be supported. By setting the design limiting condition to a nominal maximum allowable deflection, the analysis reveals that primary design outperforms reference design for the majority of the design space. This outcome is found to be the case when the spreader bar length relative to the tower height exceeds7 a critical value. The analysis is extended to lunar towers with Collapsible Tubular Mast (CTM) booms, and similar trends are observed.

Jacob G Daye↗
NASA NTRSDate not supplied

Structural Architectures for Self-Erecting Lunar Towers

The load carrying performance for deployable lunar tower architectures utilizing thin-ply composite booms are parametrically evaluated in this paper. These self-erecting towers support a communications and sensor platform on the lunar surface. The primary design consists of the Corrugated Rollable Tubular Boom (COROTUB) acting as the primary mast of the tower which supports the payload tip mass. Guy wires connecting the boom tip to spreader bars attached at the base deployer serve to correct any lateral eccentricities and provide dimensional stability. The analysis compares the maximum tip mass that this primary design can carry relative to a reference design that does not contain any guy wires or spreader bars. The results provide insights into whether the additional system mass and complexity associated with the cable-stayed design is worth the increased payload mass that can be supported. By setting the design limiting condition to a nominal maximum allowable deflection, the analysis reveals that primary design outperforms reference design for the majority of the design space. This outcome is found to be the case when the spreader bar length relative to the tower height exceeds a critical value. The analysis is extended to lunar towers with Collapsible Tubular Mast (CTM) booms, and similar trends are observed.

Jacob G Daye↗
NASA NTRS1974

Substantiation Data for Advanced Beaded and Tubular Structural Panels. Volume 3: Testing

The test program is described, which was conducted to provide the necessary experimental data to verify the design and analysis methods developed for beaded and tubular panels. Test results are summarized and presented for all local buckling and full size panel tests. Selected representative test data from each of these tests is presented in detail. The results of this program established a valid analysis and design procedure for circular tube panels. Test results from three other configurations show deformational modes which are not adequately accounted for in the present analyses.

Hedges, P. C.↗
NASA NTRS1981

Conceptual design study of potential early commercial MHD powerplant. Report of task 2 results

The conceptual design of one of the potential early commercial MHD power plants was studied. The plant employs oxygen enrichment of the combustion air and preheating of this oxygen enriched air to an intermediate temperature of 1200 F attainable with a tubular type recuperative heat exchanger. Conceptual designs of plant componets and equipment with performance, operational characteristics, and costs are reported. Plant economics and overall performance including full and part load operation are reviewed. The projected performance and estimated cost of this early MHD plant are compared to conventional power plants, although it does not offer the same high efficiency and low costs as the mature MHD power plant. Environmental aspects and the methods incorporated in plant design for emission control of sulfur and nitrogen are reviewed.

Hals, F. A.↗
DOE OSTI2025

A new tubular ironless linear induction motor using non-interrupted winding method

The ironless linear induction motor device can be used for any application which requires a large motion span or rotation restrictedly by the ironless feature due to the strong magnetic field environment. One of the possible applications is ITER diagnostics shutters. The tokamak reactor systems have a severe radiation issue during the operation. The traditional Kapton-insulated wires have significantly lower radiation resistance than an expected large radiation dose at ITER Motion Stark Effect (MSE) shutter location. Furthermore, the traditional single-sided linear induction motor winds the wire to make the N-turn pitch coils independently and then connect them in series to make a one-phase winding. Therefore, it is a big challenge to make so many radiation-protection connectors in such a limited space as inside the vacuum vessel of fusion reactors. The approved mineral-insulated kinds of cables need a large bend radius for the end turns, so the traditional single-sided linear motor with two-layer three-phase windings need to be upgraded to the tubular linear motors. The new proposed tubular ironless linear induction motor can not only overcome the large bend radius issue with the mineral-insulated cables but also allow the motor coils wound continuously around the tubular-shaped stator, forward and backward N times to make a N-turn winding for each phase, in order to resolve the radiation protection issue with the winding connection. The 3D transient Maxwell electromagnetic model with a tubular three-phase linear induction motor has been analyzed. Furthermore, this paper will present the detailed design and winding method of ironless linear induction motor actuators, and results of the 3D transient numerical simulation of the actuator performance.

Ironless↗
DOE OSTI2022

The Source Permeator System and Tritium Transport in the TEX PbLi Loop

In this work, permeation is investigated for the introduction of hydrogen isotopes into PbLi for the Tritium Extraction eXperiment (TEX). TEX is a forced-convection PbLi loop under construction at Idaho National Laboratory (INL) that will test the vacuum permeator (VP) method of tritium extraction from PbLi. The source permeator (SP) delivers atomic hydrogen (H, D, and T) from a gas-phase reservoir into the PbLi via a permeable dense metal membrane. A modular and a fixed source permeator system are presented. In the modular design, PbLi flows through the inside of a tubular membrane and gas-phase hydrogen is introduced on the outside of the membrane. Atomic hydrogen permeates radially inward through the membrane into the PbLi. In the fixed design, PbLi flows into an expansion chamber with closed-ended tubular membranes inserted. Gas-phase hydrogen is introduced on the inside of the closed-ended membranes and atomic hydrogen permeates radially outward into the flowing PbLi. Hydrogen-transport models based on steady-state mass transport through PbLi and permeation through the metal membrane were developed to assess the operation of the source permeator relative to experimental variables and to allow understanding of uncertain parameter effects, such as PbLi hydrogen-transport properties and the effective hydrogen permeability of the vacuum permeator. This modeling effort considers iron as the source permeator material and vanadium as the vacuum permeator material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1999

Novel Method Used to Inspect Curved and Tubular Structural Materials

At the NASA Lewis Research Center, a technique for the ultrasonic characterization of plates has been extended to tubes and to curved structures in general. In this technique, one performs measurements that yield a thickness-independent value of the local through-the-thickness speed of sound in a specimen. From such measurements at numerous locations across the specimen, one can construct a map of velocity as a function of location. The gradients of velocity indicated by such a map indicate local through-the-thickness-averaged microstructural parameters that affect the speed of sound. Such parameters include the pore volume fraction, mass density, fiber volume fraction (in the case of a composite material), and chemical composition. Apparatus was designed to apply the technique to tubular and other curved specimens.

Roth, Don J.↗
NASA NTRS1971

Development of boron-epoxy tubular struts for a one-third scale shuttle booster thrust structure.

A one-third scale booster thrust truss structure was designed by Grumman under an in-house program using both boron/epoxy and titanium for the tubular strut members. The boron/epoxy design showed a 22% weight saving and a two phase demonstration program was subsequently funded by NASA-MSFC. In the first phase, structural elements and the most highly loaded center member of the truss were fabricated and tested. The second phase consists of fabrication and test of a complete two-dimensional truss. The design, analysis, fabrication and test procedures are discussed in this paper which also includes the results of successful tests on the elements and center member conducted under the first phase of the NASA program.

Engler, E.↗
NASA NTRS1978

Preliminary design package for Sunair SEC-601 solar collector

The preliminary design of the Owens-Illinois model Sunair SEC-601 tubular air solar collector is presented. Information in this package includes the subsystem design and development approaches, hazard analysis, and detailed drawings available as the preliminary design review.

Source record↗