Search NASA⌕ Search

SEARCH · Search NASA

Results for “UPCONVERTER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

52 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Solid state transmitters for spaceborne radars

The SEASAT-A synthetic aperture radar, the first spaceborne SAR, utilized an all solid state RF signal synthesizer and L-band transmitter to drive a corporately fed flat plate array. The RF signal synthesizer generated a linear FM ""CHIRP'' waveform and provided stable CW reference signals used to upconvert the received signal to a unified S-band downlink channel, and to synchronize satellite control logic. The transmitter generated 1200 watts peak RF power (66 watts average) at a center frequency of 1.275 GHz from 354 watts of DC prime power. Linear FM CHIRP swept symmetrically around the center frequency with a bandwidth of 19.05 MHz and a pulse duration of 33.8 sec. Pulse repetition rate was variable from 1647 to 1944 pps. These transmitter signal parameters combined with the flat plate 34 x 7.5 ft aperture at an orbital altitude of 498 miles and a look angle 20 deg off nadir gave the SAR an 85 foot resolution over a 15.5 mile wide swath.

Turlington, T. R.↗
NASA NTRS1983

Recent developments in EHF Satcom technology

The state-of-the-art in EHF Satcom technology is assessed and hardware samples are described. Travelling wave tube amplifiers provide up to 30 percent efficiency for 20 GHz spaceborne operations and up to 20 percent efficiency at 30/44 GHz in ground operations. Solid-state power amplifiers incorporate FET and IMPATT diode technologies for 20-44 GHz transmissions using GaAs FETs and Si or GaAs diodes. Noise is reduced with loss image-enhanced mixers coupled to an IF FET amplifier, resulting ultimately in 6-7 dB noise levels compared to 19 dB gain. Finally, high power varactor upconverters have been developed to provide up to 50 mW RF output at at least 10 percent efficiency at frequencies up to 50 GHz.

Okean, H. C.↗
NASA NTRS1985

Upconversion of lower-hybrid waves by gyrating ion beams in a plasma

A gyrating ion beam, with ring shape distribution in velocity space, supports negative energy modes near the harmonics of beam gyrofrequency. An investigation of the nonlinear interaction of high-frequency lower-hybrid waves with the negative energy beam cyclotron mode is made. A nonlinear dispersion relation is derived for the coupled modes. It is shown that a gyrating ion beam frequency upconverts the lower-hybrid waves separated by harmonics of the beam gyrofrequency. This process of upconversion may thus provide a tool for the diagnostics of the gyrating ion beams. The process may also be important in the saturation of lower-hybrid waves observed in the auroral zone S3-3 satellite data.

Sharma, O. P.↗
NASA NTRS1988

High-speed analog fiber optic links for satellite communication

Large-aperture phased array antennas operating at millimeter wave frequencies are designed for space-based communications and imaging. Array elements are comprised of active transmit/receive (T/R) modules which are linked to the central processing unit through a high-speed fiberoptic network. This paper demonstrates optical control of active modules for satellite communication at 24 GHz. An approach called T/R level data mixing, which utilizes fiberoptic transmission of a data signal to individual T/R modules to be upconverted by an optically synchronized local oscillator, is demonstrated at 24 GHz. A free-running HEMT oscillator, used as local oscillator at 24 GHz, is synchronized using indirect subharmonic optical injection locking over a locking range of 14 MHz. Results of data link performance over 500-1000 MHz is also reported in terms of gain-bandwidth, linearity and third-order intercept, sensitivity, and dynamic range.

Daryoush, A. S.↗
NASA NTRS1995

Automated delay measurement system for an Earth station for Two-Way Satellite Time and Frequency Transfer

The measurement of the difference of the transmit and receive delays of the signals in a Two-Way Satellite Time and Frequency Transfer (TWSTFT) Earth station is crucial for its nanosecond time transfer capability. Also, the monitoring of the change of this delay difference with time, temperature, humidity, or barometric pressure is important for improving the TWSTFT capabilities. An automated system for this purpose has been developed from the initial design at NMi-VSL. It calibrates separately the transmit and receive delays in cables, amplifiers, upconverters and downconverters, and antenna feeds. The obtained results can be applied as corrections to the TWSTFT measurement when, before and after a measurement session, a calibration session is performed. Preliminary results obtained at NMi-VSL will be shown. Also, if available, the results of a manual version of the system that is planned to be circulated in Sept. 1994 together with a USNO portable station on a calibration trip to European TWSTFT Earth stations.

Dejong, Gerrit↗
NASA NTRS1995

Performance of a Ka-band transponder breadboard for deep-space applications

This article summarizes the design concepts applied in the development of and advanced Ka-band (34.4 GHz/32 GHz) transponder breadboard for the next generation of space communications systems applications. The selected architecture upgrades the X-band (7.2 GHz/8.4 GHz) deep-space transponder (DST) to provide Da-band up/Ka- and X-band down capability. The Ka-band transponder breadboard incorporates several state-of-the-art components, including sampling mixers, a Ka-band dielectric resonator oscillator, and microwave monolithic integrated circuits (MMICs). The MMICs that were tested in the breadboard include upconverters, downconverters, automatic gain control circuits, mixers, phase modulators, and amplifiers. The measured receiver dynamic range, tracking range, acquisition rate, static phase error, and phase jitter characteristics of the Ka-band breadboard interfaced to the advanced engineering model X-band DST are in good agreement with the expected performance. The results show a receiver tracking threshold of -149 dBm with a dynamic range of 80 dB and a downlink phase jitter of 7 deg rms. The analytical results of phase noise and Allan standard deviation are in good agreement with the experimental results.

Mysoor, N. R.↗
NASA NTRS1996

Ultra Small Aperture Terminal: System Design and Test Results

The Ultra Small Aperture Terminal (USAT) has been developed to test and demonstrate remote and broadcast satcom applications via the Advanced Communications Technology Satellite (ACTS). The design of these ground stations emphasize small size, low power consumption, portable and rugged terminals. Each ground station includes several custom design parts such as 35 cm diameter antenna, 1/4 Watt transmitter with built-in upconverter, and 4.0 dB Noise Figure (NF) receiver with built-in downconverter. In addition, state-of-the-art commercial parts such as highly stable ovenized crystal oscillators and dielectric resonator oscillators are used in the ground station design. Presented in this paper are system level design description, performance, and sample applications.

Sohn, Philip Y.↗
NASA NTRS2003

A 94 GHz RF Electronics Subsystem for the CloudSat Cloud Profiling Radar

The CloudSat spacecraft, scheduled for launch in 2004, will carry the 94 GHz Cloud Profiling Radar (CPR) instrument. The design, assembly and test of the flight Radio Frequency Electronics Subsystem (RFES) for this instrument has been completed and is presented here. The RFES consists of an Upconverter (which includes an Exciter and two Drive Amplifiers (DA's)), a Receiver, and a Transmitter Calibrator assembly. Some key performance parameters of the RFES are as follows: dual 100 mW pulse-modulated drive outputs at 94 GHz, overall Receiver noise figure < 5.0 dB, a highly stable W-band noise source to provide knowledge accuracy of Receiver gain of < 0.4 dB over the 2 year mission life, and a W-band peak power detector to monitor the transmitter output power to within 0.5 dB over life. Some recent monolithic microwave integrated circuit (MMIC) designs were utilized which implement the DA's in 0.1 micron GaAs high electron-mobility transistor (HEMT) technology and the Receiver low-noise amplifier (LNA) in 0.1 micron InP HEMT technology.

radio frequency electronics subsystem (RFES)↗
NASA NTRS2009

Generating Ka-Band Signals Using an X-Band Vector Modulator

A breadboard version of a transmitter for radio communication at a carrier frequency of 32 GHz (which is in the Ka band) utilizes a vector modulator operating at a carrier frequency of 8 GHz (the low end of the X band) to generate any of a number of advanced modulations that could include amplitude and/or phase modulation components. The 8-GHz modulated signal is mixed with a 24-GHz signal generated by an upconverter to obtain the desired 32-GHz modulated output. The transmitter is being developed as a prototype of downlink transmitters for transmission of data from spacecraft to Earth at high rates (>100 Mb/s). The transmitter design could also be adapted to terrestrial and Earth/satellite communication links. The advanced modulations (which can include M-ary phase-shift keying (M-PSK), offset phase-shift keying (OPSK), and M-ary quadrature amplitude modulation (M-QAM). These modulations are needed because for a given amount of signal bandwidth, they enable transmission of data at rates greater than those of older, simpler modulation schemes. The transmitter architecture (see figure) was chosen not only to enable generation of the required modulations at 32 GHz but also to reduce the number of components needed to implement the transmitter. Instead of incorporating an 8-GHz signal source, the transmitter utilizes an 8-GHz signal generated by a voltage-controlled oscillator that is part of an X-band transponder with which the fully developed version of this transmitter would be used in the original intended spacecraft application. The oscillator power is divided onto two paths, one of which goes through the vector modulator, the other through amplifiers and a 3 frequency multiplier. Band-pass filters are included downstream of the frequency multiplier to suppress unwanted harmonics.

Smith, Scott↗
NASA NTRS2011

Flexible, reconfigurable, power efficient transmitter and method

A flexible, reconfigurable, power efficient transmitter device and method is provided. In one embodiment, the method includes receiving outbound data and determining a mode of operation. When operating in a first mode the method may include modulation mapping the outbound data according a modulation scheme to provide first modulation mapped digital data, converting the first modulation mapped digital data to an analog signal that comprises an intermediate frequency (IF) analog signal, upconverting the IF analog signal to produce a first modulated radio frequency (RF) signal based on a local oscillator signal, amplifying the first RF modulated signal to produce a first RF output signal, and outputting the first RF output signal via an isolator. In a second mode of operation method may include modulation mapping the outbound data according a modulation scheme to provide second modulation mapped digital data, converting the second modulation mapped digital data to a first digital baseband signal, conditioning the first digital baseband signal to provide a first analog baseband signal, modulating one or more carriers with the first analog baseband signal to produce a second modulated RF signal based on a local oscillator signal, amplifying the second RF modulated signal to produce a second RF output signal, and outputting the second RF output signal via the isolator. The digital baseband signal may comprise an in-phase (I) digital baseband signal and a quadrature (Q) baseband signal.

Bishop, James W.↗
NASA NTRSDate not supplied

Geodetic Reference Instrument Transponder for Small Satellites (Gritss)

The accuracy of the Terrestrial Reference Frame is limited by systematic errors in tying the contributions from the different geodetic techniques. Local survey uncertainties are limited due to the inaccessibility of the instrument reference points. NASA is implementing a technology demonstration mission called Geodetic Reference Instrument Transponder for Small Satellites(GRITSS) that uses a small satellite as a space-based ref-refence point for tying together collocated geodetic stations. The technology being demonstrated uses a novel idea of upconverting the Global Positioning System (GPS) signals received at the satellite and transponding them to a VLBI Global Observing System (VGOS) antenna ground station. This approach does not require the satellite to be in view of more than one VLBI station at a time, allowing the use of Low Earth Orbits and an inexpensive CubeSat. The demonstration will initially involve only the NASA VGOS stations in Maryland, Hawaii, and Texas, but may be expanded later in the mission to include other international VGOS stations. This presentation will provide an overview of the GRITSS mission and the measurement concept.

S M Merkowitz↗
NASA NTRSDate not supplied

Geodetic Reference Instrument Transponder for Small Satellites (GRITTS)

The accuracy of the Terrestrial Reference Frame is limited by systematic errors in tying the contributions from the different geodetic techniques. Local survey uncertainties are limited due to the inaccessibility of the instrument reference points. NASA is implementing a technology demonstration mission called Geodetic Reference Instrument Transponder for Small Satellites(GRITSS) that uses a small satellite as a space-based ref-refence point for tying together collocated geodetic stations. The technology being demonstrated uses a novel idea of upconverting the Global Positioning System (GPS) signals received at the satellite and transponding them to a VLBI Global Observing System (VGOS) antenna ground station. This approach does not require the satellite to be in view of more than one VLBI station at a time, allowing the use of Low Earth Orbits and an inexpensive CubeSat. The demonstration will initially involve only the NASA VGOS stations in Maryland, Hawaii, and Texas, but may be expanded later in the mission to include other international VGOS stations. This presentation will provide an overview of the GRITSS mission and the measurement concept.

S. M. Merkowitz↗
NASA NTRSDate not supplied

Geodetic Reference Instrument Transponder for Small Satellites

The local ties between Satellite Laser Ranging stations and other collocated geodetic stations are an important component of the realization of the International Terrestrial Reference Frame but the survey accuracies are limited due to the inaccessibility of the instrument reference points. The NASA Geodetic Reference Instrument Transponder for Small Satellites (GRITSS) technology demonstration mission is designed to overcome this limitation by using a small satellite as a space-based reference point for tying together the measurement points of collocated geodetic stations. The GRITSS instrument upconverts the Global Positioning System (GPS) signals received at the satellite in real-time to S and X band and transmits them to a VLBI Global Observing System (VGOS) antenna ground station. The measurement observables do not require the satellite to be in view of more than one VLBI station at a time. The GRITSS demonstration mission utilizes a 12-UL CubeSat in a Low Earth, Sun Synchronous orbit. Tracking by the global ILRS network throughout the life of the mission is critical to establishing the space-based reference along with the precision orbit determination required by the measurement concept. Due to limitations in spacecraft power and other constraints, the initial phase of the mission will only broadcast the GRITSS VLBI signals twice a day to each of the NASA VGOS stations in Maryland, Hawaii, and Texas, but other international VGOS stations may be added during the second half of the mission. An overview of the GRITSS mission and measurement concept will be presented.

Stephen M Merkowitz↗
NASA NTRSDate not supplied

Geodetic Reference Instrument Transponder for Small Satellites (GRITTS)

The accuracy of the Terrestrial Reference Frame is limited by systematic errors in tying the contributions from the different geodetic techniques. Local survey uncertainties are limited due to the inaccessibility of the instrument reference points. NASA is implementing a technology demonstration mission called Geodetic Reference Instrument Transponder for Small Satellites(GRITSS) that uses a small satellite as a space-based ref-refence point for tying together collocated geodetic stations. The technology being demonstrated uses a novel idea of upconverting the Global Positioning System (GPS) signals received at the satellite and transponding them to a VLBI Global Observing System (VGOS) antenna ground station. This approach does not require the satellite to be in view of more than one VLBI station at a time, allowing the use of Low Earth Orbits and an inexpensive CubeSat. The demonstration will initially involve only the NASA VGOS stations in Maryland, Hawaii, and Texas, but may be expanded later in the mission to include other international VGOS stations. This presentation will provide an overview of the GRITSS mission and the measurement concept.

S M Merkowitz↗