Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ultra-high Frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

40 records · Page 3

Interferometric apparatus for ultra-high precision displacement measurement

A high-precision heterodyne interferometer measures relative displacement by creating a thermally-insensitive system generally not subject to polarization leakage. By using first and second light beams separated by a small frequency difference (.DELTA.f), beams of light at the first frequency (f.sub.0) are reflected by co-axial mirrors, the first mirror of which has a central aperture through which the light is transmitted to and reflected by the second mirror. Prior to detection, the light beams from the two mirrors are combined with light of the second and slightly different frequency. The combined light beams are separated according to the light from the mirrors. The change in phase (.DELTA..phi.) with respect to the two signals is proportional to the change in distance of Fiducial B by a factor of wavelength (.lambda.) divided by 4.pi. (.DELTA.L=.lambda..DELTA..phi.1/(4.pi.)). In a second embodiment, a polarizing beam splitting system can be used.

Zhao, Feng↗

A Gigabit-per-Second Ka-Band Demonstration Using a Reconfigurable FPGA Modulator

Gigabit-per-second communications have been a desired target for future NASA Earth science missions, and for potential manned lunar missions. Frequency bandwidth at S-band and X-band is typically insufficient to support missions at these high data rates. In this paper, we present the results of a 1 Gbps 32-QAM end-to-end experiment at Ka-band using a reconfigurable Field Programmable Gate Array (FPGA) baseband modulator board. Bit error rate measurements of the received signal using a software receiver demonstrate the feasibility of using ultra-high data rates at Ka-band, although results indicate that error correcting coding and/or modulator predistortion must be implemented in addition. Also, results of the demonstration validate the low-cost, MOS-based reconfigurable modulator approach taken to development of a high rate modulator, as opposed to more expensive ASIC or pure analog approaches.

reconfigurable↗

CMOS-Compatible SOI MESFETS for Radiation-Hardened DC-to-DC Converters

A radiation-tolerant transistor switch has been developed that can operate between 196 and +150 C for DC-to-DC power conversion applications. A prototype buck regulator component was demonstrated to be performing well after a total ionizing dose of 300 krad(Si). The prototype buck converters showed good efficiencies at ultra-high switching speeds in the range of 1 to 10 MHz. Such high switching frequency will enable smaller, lighter buck converters to be developed as part of the next project. Switching regulators are widely used in commercial applications including portable consumer electronics.

Thornton, Trevor↗

Mapping Boreal Forest Spruce Beetle Health Status at the Individual Crown Scale Using Fused Spectral and Structural Data

The frequency and severity of spruce bark beetle outbreaks are increasing in boreal forests leading to widespread tree mortality and fuel conditions promoting extreme wildfire. Detection of beetle infestation is a forest health monitoring (FHM) priority but is hampered by the challenges of detecting early stage (“green”) attack from the air. There is indication that green stage might be detected from vertical gradients of spectral data or from shortwave infrared information distributed within a single crown. To evaluate the efficacy of discriminating “non-infested”, “green”, and “dead” health statuses at the landscape scale in Alaska, USA, this study conducted spectral and structural fusion of data from: (1) Unoccupied aerial vehicle (UAV) multispectral (6 cm) + structure from motion point clouds (~700 pts per sq. m); and (2) Goddard Lidar Hyperspectral Thermal (G-LiHT) hyperspectral (400 to 1000 nm, 0.5 m) + SWIR-band lidar (~32 pts per sq.m). We achieved 78% accuracy for all three health statuses using spectral + structural fusion from either UAV or G-LiHT and 97% accuracy for non-infested/dead using G-LiHT. We confirm that UAV 3D spectral (e.g., greenness above versus below median height in crown) and lidar apparent reflectance metrics (e.g., mean reflectance at 99th percentile height in crown), are of high value, perhaps capturing the vertical gradient of needle degradation. In most classification exercises, UAV accuracy was lower than G-LiHT indicating that collecting ultra-high spatial resolution data might be less important than high spectral resolution information. While the value of passive optical spectral information was largely confined to the discrimination of non-infested versus dead crowns, G-LiHT hyperspectral band selection (~400, 675, 755, and 940 nm) could inform future FHM mission planning regarding optimal wavelengths for this task. Interestingly, the selected regions mostly did not align with the band designations for our UAV multispectral data but do correspond to, e.g., Sentinel-2 red edge bands, suggesting a path forward for moderate scale bark beetle detection when paired with suitable structural data.

Janice Cessna↗