Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND TUNNEL MODEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Wind Tunnel Modeling Seminar

The NASA Altitude Wind Tunnel (AWT) program was examined and reviewed. AWT project status and modeling program are presented as well as the modeling programs for a number of other wind tunnels such as the National Transonic Facility, Boeing tunnel, and NASA's 40 by 80 by 120 foot tunnel. Finally, AWT aerodynamic design status, aerothermodynamic design, drive system, icing equipment, acoustics, and dynamics and controls are discussed. The need for this tunnel is examined in the wake of new aerospace research programs. All documents are presented in viewgraph format.

Source record↗
NASA NTRS1994

Effects of vibration on inertial wind-tunnel model attitude measurement devices

Results of an experimental study of a wind tunnel model inertial angle-of-attack sensor response to a simulated dynamic environment are presented. The inertial device cannot distinguish between the gravity vector and the centrifugal accelerations associated with wind tunnel model vibration, this situation results in a model attitude measurement bias error. Significant bias error in model attitude measurement was found for the model system tested. The model attitude bias error was found to be vibration mode and amplitude dependent. A first order correction model was developed and used for estimating attitude measurement bias error due to dynamic motion. A method for correcting the output of the model attitude inertial sensor in the presence of model dynamics during on-line wind tunnel operation is proposed.

Young, Clarence P., Jr.↗
NASA NTRS1988

Surface flow visualization of separated flows on the forebody of an F-18 aircraft and wind-tunnel model

A method of in-flight surface flow visualization similar to wind-tunnel-model oil flows is described for cases where photo-chase planes or onboard photography are not practical. This method, used on an F-18 aircraft in flight at high angles of attack, clearly showed surface flow streamlines in the fuselage forebody. Vortex separation and reattachment lines were identified with this method and documented using postflight photography. Surface flow angles measured at the 90 and 270 degrees meridians show excellent agreement with the wind tunnel data for a pointed tangent ogive with an aspect ratio of 3.5. The separation and reattachment line locations were qualitatively similar to the F-18 wind-tunnel-model oil flows but neither the laminar separation bubble nor the boundary-layer transition on the wind tunnel model were evident in the flight surface flows. The separation and reattachment line locations were in fair agreement with the wind tunnel data for the 3.5 ogive. The elliptical forebody shape of the F-18 caused the primary separation lines to move toward the leeward meridian. Little effect of angle of attack on the separation locations was noted for the range reported.

Fisher, David F.↗
NASA NTRS2014

A New Global Regression Analysis Method for the Prediction of Wind Tunnel Model Weight Corrections

A new global regression analysis method is discussed that predicts wind tunnel model weight corrections for strain-gage balance loads during a wind tunnel test. The method determines corrections by combining "wind-on" model attitude measurements with least squares estimates of the model weight and center of gravity coordinates that are obtained from "wind-off" data points. The method treats the least squares fit of the model weight separate from the fit of the center of gravity coordinates. Therefore, it performs two fits of "wind- off" data points and uses the least squares estimator of the model weight as an input for the fit of the center of gravity coordinates. Explicit equations for the least squares estimators of the weight and center of gravity coordinates are derived that simplify the implementation of the method in the data system software of a wind tunnel. In addition, recommendations for sets of "wind-off" data points are made that take typical model support system constraints into account. Explicit equations of the confidence intervals on the model weight and center of gravity coordinates and two different error analyses of the model weight prediction are also discussed in the appendices of the paper.

strain-gage balance↗
NASA NTRS1985

Initial investigation of cryogenic wind tunnel model filler materials

Various filler materials are being investigated for applicability to cryogenic wind tunnel models. The filler materials will be used to fill surface grooves, holes and flaws. The severe test environment of cryogenic models precludes usage of filler materials used on conventional wind tunnel models. Coefficients of thermal expansion, finishing characteristics, adhesion and stability of several candidate filler materials were examined. Promising filler materials are identified.

Rush, H. F.↗
NASA NTRS1987

Portable Test And Monitoring System For Wind-Tunnel Models

Portable system developed to test and monitor instrumentation used in wind-tunnel models. Self-contained and moves easily to model, either before or after model installed in wind tunnel. System is 44 1/2 in. high, 22 in. wide, and 17 in. deep and weighs 100 lb. Primary benefits realized with portable test and monitoring system associated with saving of time.

Poupard, Charles A.↗
NASA NTRS2006

Control Surface Interaction Effects of the Active Aeroelastic Wing Wind Tunnel Model

This paper presents results from testing the Active Aeroelastic Wing wind tunnel model in NASA Langley s Transonic Dynamics Tunnel. The wind tunnel test provided an opportunity to study aeroelastic system behavior under combined control surface deflections, testing for control surface interaction effects. Control surface interactions were observed in both static control surface actuation testing and dynamic control surface oscillation testing. The primary method of evaluating interactions was examination of the goodness of the linear superposition assumptions. Responses produced by independently actuating single control surfaces were combined and compared with those produced by simultaneously actuating and oscillating multiple control surfaces. Adjustments to the data were required to isolate the control surface influences. Using dynamic data, the task increases, as both the amplitude and phase have to be considered in the data corrections. The goodness of static linear superposition was examined and analysis of variance was used to evaluate significant factors influencing that goodness. The dynamic data showed interaction effects in both the aerodynamic measurements and the structural measurements.

Heeg, Jennifer↗
NASA NTRS2014

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation

This is part 2 of a two part document. Part 1 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression." A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind tunnel model of a joined wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind tunnel model was mated to a new, two degree of freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at10 percent static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free flying wind tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Scott, Robert C.↗
NASA NTRS1992

An approach for increasing aeroelastic divergence dynamic pressure of wind-tunnel models

An approach for increasing the aeroelastic divergence dynamic pressure of wind-tunnel model support systems is presented. A study has been conducted to investigate the effect of increased flexibility of the forward portion of balances on the divergence pressure of wind-tunnel models. The study utilized prior divergence analyses completed for various models to be tested in NASA Langley Research Center's National Transonic Facility, the Engineering Analysis Language finite-element analysis code, and an in-house computer program which solves for divergence dynamic pressure utilizing a transfer-matrix method based on fourth-order Runge-Kutta integration. Analytical results for balance flexibility changes versus changes in divergence pressure were obtained and demonstrate that a significant increase in divergence pressure can be obtained from the increased flexibility of the balance's forward portion for many models and their support systems.

Edwards, R. W.↗
NASA NTRS1985

A voice-actuated wind tunnel model leak checking system

A voice-actuated wind tunnel model leak checking system was developed. The system uses a voice recognition and response unit to interact with the technician along with a graphics terminal to provide the technician with visual feedback while checking a model for leaks.

Larson, W. E.↗
NASA NTRS1990

The design of two sonic boom wind tunnel models from conceptual aircraft which cruise at Mach numbers of 2.0 and 3.0

A method for designing wind tunnel models of conceptual, low-boom, supersonic cruise aircraft is presented. Also included is a review of the procedures used to design the conceptual low-boom aircraft. In the discussion, problems unique to, and encountered during, the design of both the conceptual aircraft and the wind tunnel models are outlined. The sensitivity of low-boom characteristics in the aircraft design to control the volume and lift equivalent area distributions was emphasized. Solutions to these problems are reported; especially the two which led to the design of the wind tunnel model support stings.

Mack, Robert J.↗
NASA NTRS2012

An Overview of the Semi-Span Super-Sonic Transport (S4T) Wind-Tunnel Model Program

A summary of computational and experimental aeroelastic (AE) and aeroservoelastic (ASE) results for the Semi-Span Super-Sonic Transport (S4T) wind-tunnel model is presented. A broad range of analyses and multiple AE and ASE wind-tunnel tests of the S4T wind-tunnel model have been performed in support of the ASE element in the Supersonics Program, part of the NASA Fundamental Aeronautics Program. This paper is intended to be an overview of multiple papers that comprise a special S4T technical session. Along those lines, a brief description of the design and hardware of the S4T wind-tunnel model will be presented. Computational results presented include linear and nonlinear aeroelastic analyses, and rapid aeroelastic analyses using CFD-based reduced-order models (ROMs). A brief survey of some of the experimental results from two open-loop and two closed-loop wind-tunnel tests performed at the NASA Langley Transonic Dynamics Tunnel (TDT) will be presented as well.

Silva, Walter A.↗
NASA NTRS1997

Static Aeroelastic Analysis of Transonic Wind Tunnel Models Using Finite Element Methods

A computational method for accurately predicting the static aeroelastic deformations of typical transonic transport wind tunnel models is described. The method utilizes a finite element method (FEM) for predicting the deformations. Extensive calibration/validation of this method was carried out using a novel wind-off wind tunnel model static loading experiment and wind-on optical wing twist measurements obtained during a recent wind tunnel test in the National Transonic Facility (NTF) at NASA LaRC. Further validations were carried out using a Navier-Stokes computational fluid dynamics (CFD) flow solver to calculate wing pressure distributions about several aeroelastically deformed wings and comparing these predictions with NTF experimental data. Results from this aeroelastic deformation method are in good overall agreement with experimentally measured values. Including the predicted deformations significantly improves the correlation between CFD predicted and experimentally measured wing & pressures.

Hooker, John R.↗
NASA NTRS2017

Computational Results for the KTH-NASA Wind-Tunnel Model Used for Acquisition of Transonic Nonlinear Aeroelastic Data

A status report is provided on the collaboration between the Royal Institute of Technology (KTH) in Sweden and the NASA Langley Research Center regarding the aeroelastic analyses of a full-span fighter configuration wind-tunnel model. This wind-tunnel model was tested in the Transonic Dynamics Tunnel (TDT) in the summer of 2016. Large amounts of data were acquired including steady/unsteady pressures, accelerations, strains, and measured dynamic deformations. The aeroelastic analyses presented include linear aeroelastic analyses, CFD steady analyses, and analyses using CFD-based reduced-order models (ROMs).

Silva, Walter A.↗
NASA NTRS1986

Surface roughness studies for wind tunnel models used in high Reynolds number testing

This paper focuses on stylus and optical techniques for the measurement of surface roughness in wind tunnel models. The stylus instruments provide detailed information, such as surface profiles and area maps, that may then be used either to calculate statistical properties (i.e., the rms surface roughness) or to study individual surface peaks or other features. By contrast, certain optical techniques yield area-averaged statistical properties of the surface roughness directly. Two instruments that use the technique of optical angular scattering are compared. One is a research instrument that has been developed to study the basic scattering phenomena by testing the optical theories and surface models used in inverse calculations of statistical roughness parameters. The second instrument is more compact and is under development as a hand held, on-line device to be used during manufacture of wind tunnel models for the National Transonic Facility at NASA Langley Research Center. The scattering geometries for the two instruments are compared and results from these instruments and the stylus technique are shown for roughness specimens that are typical of the surface finish of wind tunnel models.

Vorburger, T. V.↗
NASA NTRSDate not supplied

High Fidelity Adaptively Refined CFD and Reduced Order Models of a High Aspect Ratio Aeroelastic Wing Wind Tunnel Model

Robust adaptive mesh refinement for transonic conditions is one of the most difficult challenges to advancing CFD usage for certification by analysis. Transonic fluid-structure interaction cases represent an even more difficult challenge for adaptive mesh refinement. Production aircraft furthermore have structural models that have gaps and discontinuities that make the interdomain transfer of loads and deflections difficult. This adds to the challenge of adaptive mesh refinement. An initial attempt to create an adaptive mesh refinement process that refines regions of high flow gradient based around the HeldenMesh software is presented. The method is applied to the Integrated Adaptive Wing Technology Maturation (IAWTM) configuration. That has developed an aspect ratio 13.5 wing aeroelastic wind-tunnel model for testing in the Transonic Dynamics Tunnel (TDT). The high levels of deformation of this wing make the adaptation of meshes for the static shape difficult and has necessitated some creativity in how to efficiently adapt meshes. A time-domain identification of the unsteady system based on flexible modes using the adapted meshes is performed.

Robert E. Bartels↗
NASA NTRS1985

Initial Investigation of Cryogenic Wind Tunnel Model Filler Materials

Filler materials are used for surface flaws, instrumentation grooves, and fastener holes in wind tunnel models. More stringent surface quality requirements and the more demanding test environment encountered by cryogenic wind tunnels eliminate filler materials such as polyester resins, plaster, and waxes used on conventional wind tunnel models. To provide a material data base for cryogenic models, various filler materials are investigated. Surface quality requirements and test temperature extremes require matching of coefficients of thermal expansion or interfacing materials. Microstrain versus temperature curves are generated for several candidate filler materials for comparison with cryogenically acceptable materials. Matches have been achieved for aluminum alloys and austenitic steels. Simulated model surfaces are filled with candidate filler materials to determine finishing characteristics, adhesion and stability when subjected to cryogenic cycling. Filler material systems are identified which meet requirements for usage with aluminum model components.

Firth, G. C.↗