Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS, TAPERED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1937

Span load distribution for tapered wings with partial-span flaps

Tables are given for determining the load distribution of tapered wings with partial-span flaps placed either at the center or at the wing tips. Seventy-two wing-flap combinations, including two aspect ratios, four taper ratios, and nine flap lengths, are included. The distributions for the flapped wing are divided into two parts, one a zero lift distribution due primarily to the flaps and the other an additional lift distribution due to an angle of attack of the wing as a whole. Comparison between theoretical and experimental results for wings indicate that the theory may be used to predict the load distribution with sufficient accuracy for structural purposes.

Pearson, H A↗
NASA NTRS1938

Investigations on the downwash behind a tapered wing with fuselage and propeller

The new downwash measurements behind a tapered wing with parallel center section described in the present report can be brought into good agreement with theoretical calculations if made on the basis of not-rolled-up vortex sheet and allowance is made for the lowering of the sheet. The test values are about 1 degree higher than the "upper limit" established for it, as against approximately 0.5 degrees in the earlier tests behind a rectangular and elliptical wing. The measurements on lateral axes, especially if lying below the wing on a level with the vortex train, disclosed in accord with the lift distribution, a marked change in angle over the span of the tail in contrast to the rectangular and elliptical wing.

Muttray, H↗
NASA NTRS1943

Wind-Tunnel Tests of an NACA 44R-Series Tapered Wing with a Straight Trailing Edge and a Constant-Chord Center Section

As part of a general investigation in the NACA 19-foot pressure tunnel to determine stall characteristics and effectiveness of high-lift devices on wings of various sections, tests were made of a tapered. wing having NACA 44R-series airfoil sections. Lift, drag, pitching-moment, and stall characteristics were determined at a Reynolds number of 4,850,000 for the plain wing and for the wing with partial-and with full-span split flaps. The stall progressed slowly over The plain wing; a gradual loss of lift for angles of attack up to and beyond that for the maximum lift coefficient resulted. As Compared with the stall of the plain wing, the initial stall of the wing with either partial-span or full-span flaps deflected occurred at a higher angle of attack and the stall progressed much more rapidly. The maximum lift coefficients at a Reynolds number of 4,850,000 were 1.35 for the plain wing, 2.25 for the wing with partial-span flaps at 60 deg, and 2.67 for the wing with full-span flaps at 60 deg. The positions of the aerodynamic center, in terms of mean chords back of the leading edge of the root section, were approximately 0.458 with no flaps, 0.483 with partial-span flaps at 60 deg, and 0.498 with full-span flaps at 60 deg.

Neely, Robert H.↗
NASA NTRS1939

Calculation of the aerodynamic characteristics of tapered wings with partial-span flaps

Factors derived from wing theory are presented. By means of these factors, the angle of zero lift, the lift-curve slope, the pitching moment, the aerodynamic-center position, and the induced drag of tapered wings with partial-span flaps may be calculated. The factors are given for wings of aspect ratios 6 and 10 , of taper ratios from 0.25 to 1.00, and with flaps of various length. An example is presented of the method of application of the factors. Fair agreement with experimental results is shown for two wings of different taper ratio having plain flaps of various spacing.

Person, Henry A↗
NASA NTRS1976

Swept-tapered-wing aerodynamics

Computer program calculates effects on lift and drag of blowing two jets over swept tapered wing at low subsonic speeds. Algorithm used in based on vortex lattice representation of wing lifting surface on line source-sink distribution to represent effects of exhaust jets.

Putnam, L. E.↗
NASA NTRS1950

Summary of the Aerodynamic Characteristics and Flying Qualities Obtained from Flights of Rocket-Propelled Models of an Airplane Configuration Incorporating a Sweptback Inversely Tapered Wing at Transonic and Low-Supersonic Speeds

Flight tests have been conducted on rocket-propelled models of an airplane configuration incorporating a sweptback wing with inverse taper to investigate the drag, stability, and control characteristics at transonic and supersonic speeds. The models were tested with a conventional tail arrangement in the Mach number range from 0.55 to 1.2. In addition to the various aerodynamic parameters obtained, the flying qualities were computed for a full-scale airplane with the center-of-gravity location at 18 percent of the mean aerodynamic chord. Also, included in this investigation are drag measurements made on relatively simple fixed-control models tested with both conventional and V-tail arrangements.

Mitcham, Grady L.↗
NASA NTRS1939

Flight Tests of Retractable Ailerons on a Highly Tapered Wing

A flight investigation was conducted to determine the lateral-control characteristics of retractable ailerons installed on a highly tapered wing. The effectiveness of the ailerons in producing roll was measured at various air speeds with full-span plain flaps both neutral and deflected 45 degrees. The direction of the yawing moment created by the ailerons was also noted. The lateral control provided by the retractable ailerons used in this investigation was approximately the same as that obtained with the plain ailerons of equal span with which the airplane was previously equipped. The amount of control available was found to be somewhat inadequate, apparently because of the rather short span of the ailerons (0.327 of the wing span). It is likely that, with an aileron span of from 0.50 to 0.60 of the wing span, a satisfactory degree of control would be obtained. With the full-span flaps deflected 45 degrees, the rolling action of the ailerons was increased about 30 percent over that obtained with the flaps neutral at the same speed. The yawing moment produced by the ailerons was in the same sense as the rolling moment, i.e., right roll was accompanied by yaw. Lag in the response of the rolling action to control application was not large enough to be noticed by the pilots. No appreciable control force was apparent to the pilots, which was considered somewhat undesirable. Minor modifications in the design of the ailerons, however, would probably correct this fault.

Wetmore, J W↗
NASA NTRS1947

Pressure-Distribution Measurements on a Straight and on a 35 Degree Swept-Back Tapered Wing

The spanwise lift-distribution measurements in straight air flow on a straight and a 35 deg swept-back tapered wing (NACA airfoil section 0012) are compared with theory for two angles of attack each (alpha approx. 6 deg and alpha approx. 12 deg) in the unstalled range of flow. The complete pressure distribution for the greater of the two angles is indicated.

Thiel, A.↗
NASA NTRS1950

Theoretical stability derivatives of thin sweptback wings tapered to a point with sweptback or sweptforward trailing edges for a limited range of supersonic speeds

The stability derivatives valid for a limited range of supersonic speeds are presented for a series of sweptback wings tapered to a point with sweptback or sweptforward trailing edges. These wings were derived by modifying the trailing edge of a basic triangular wing so that it coincided with lines drawn from the wing tips to the wing axis of symmetry. The stability derivatives were formulated by using the pressure distributions previously obtained for the basic triangular wing for angle of attack, constant vertical acceleration, sideslip, pitching, rolling, and yawing. Explicit expressions are given for the stability derivatives with respect to principal body axes, and conversion formulas are provided for the transformation to stability axes. The results are limited to Mach numbers for which the wing is contained within the Mach cones springing from the vertex and from the trailing edge of the center section of the wing.

Malvestuto, Frank S , Jr↗
NASA NTRS1954

Effects of Sweep and Thickness on the Static Longitudinal Aerodynamic Characteristics of a Series of Thin, Low-aspect-ratio, Highly Tapered Wings at Transonic Speeds : Transonic-bump Method

An investigation by the transonic-bump technique of the static longitudinal aerodynamic characteristics of a series of thin, low-aspect-ratio, highly tapered wings has been made in the Langley high-speed 7- by 10-foot tunnel. The Mach number range extended from about 0.60 to 1.18, with corresponding Reynolds numbers ranging from about 0.75 x 10(6) to 0.95 x 10(6). The angle of attack range was from -10 degrees to approximately 32 degrees.The effects on drag and lift-drag ratio of a variation in sweep angle from -14.03 degrees to 45 degrees with respect to the quarter-chord line for wings of 3-percent-chord thickness was found to be small in comparison to the effects of a variation in thickness from 2 percent chord to 4.5 percent chord for wings with 14.03 degree sweepback. For the range of variables considered, variations in plan form were considerably more important with regard to longitudinal stability characteristics than the variations in thickness. For the series of basic wings having an aspect ratio of 4, the most hearly linear pitching-moment characteristics were obtained with 26.57 degree of sweepback of the quarter-chord line. However, for the modified series of wings (obtained by clipping the tips of the original wings parallel to the plane of symmetry to give an aspect ratio of 3 and a taper ratio of 0.143), the most nearly linear pitching-moment characteristics were obtained with 36.87 degrees of sweepback. By decreasing the thickness-to-chord ratios from 0.03 to 0.02, a large increase in lift-curve slope was obtained for both the basic and modified wings. All of the wings of both series had fairly large inward shifts of the lateral center-of-pressure location (indicative of tip stalling) with increasing lift coefficient, except those wings having minimum sweepback angles.

Fournier, Paul G↗
NASA NTRS1977

Compressible laminar boundary layers with suction on swept and tapered wings

In this paper we present a numerical method for solving the compressible laminar boundary-layer equations with suction on swept and tapered wings. The method employs an efficient two-point finite-difference method to solve the governing equations, and a very convenient similarity transformation which removes the wall normal velocity as a boundary condition and places it into the governing equations as a parameter. In this way the awkward nonlinear boundary condition which couples all the variables is avoided. To test and demonstrate the method, we present a sample calculation for a typical laminar-flow-control (LFC) wing.

Kaups, K.↗