Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - DESIGN WING, TAPERED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1943

Wind-Tunnel Tests of an NACA 44R-Series Tapered Wing with a Straight Trailing Edge and a Constant-Chord Center Section

As part of a general investigation in the NACA 19-foot pressure tunnel to determine stall characteristics and effectiveness of high-lift devices on wings of various sections, tests were made of a tapered. wing having NACA 44R-series airfoil sections. Lift, drag, pitching-moment, and stall characteristics were determined at a Reynolds number of 4,850,000 for the plain wing and for the wing with partial-and with full-span split flaps. The stall progressed slowly over The plain wing; a gradual loss of lift for angles of attack up to and beyond that for the maximum lift coefficient resulted. As Compared with the stall of the plain wing, the initial stall of the wing with either partial-span or full-span flaps deflected occurred at a higher angle of attack and the stall progressed much more rapidly. The maximum lift coefficients at a Reynolds number of 4,850,000 were 1.35 for the plain wing, 2.25 for the wing with partial-span flaps at 60 deg, and 2.67 for the wing with full-span flaps at 60 deg. The positions of the aerodynamic center, in terms of mean chords back of the leading edge of the root section, were approximately 0.458 with no flaps, 0.483 with partial-span flaps at 60 deg, and 0.498 with full-span flaps at 60 deg.

Neely, Robert H.↗
NASA NTRS1939

Calculation of the aerodynamic characteristics of tapered wings with partial-span flaps

Factors derived from wing theory are presented. By means of these factors, the angle of zero lift, the lift-curve slope, the pitching moment, the aerodynamic-center position, and the induced drag of tapered wings with partial-span flaps may be calculated. The factors are given for wings of aspect ratios 6 and 10 , of taper ratios from 0.25 to 1.00, and with flaps of various length. An example is presented of the method of application of the factors. Fair agreement with experimental results is shown for two wings of different taper ratio having plain flaps of various spacing.

Person, Henry A↗
NASA NTRS1976

Swept-tapered-wing aerodynamics

Computer program calculates effects on lift and drag of blowing two jets over swept tapered wing at low subsonic speeds. Algorithm used in based on vortex lattice representation of wing lifting surface on line source-sink distribution to represent effects of exhaust jets.

Putnam, L. E.↗
NASA NTRS1950

Summary of the Aerodynamic Characteristics and Flying Qualities Obtained from Flights of Rocket-Propelled Models of an Airplane Configuration Incorporating a Sweptback Inversely Tapered Wing at Transonic and Low-Supersonic Speeds

Flight tests have been conducted on rocket-propelled models of an airplane configuration incorporating a sweptback wing with inverse taper to investigate the drag, stability, and control characteristics at transonic and supersonic speeds. The models were tested with a conventional tail arrangement in the Mach number range from 0.55 to 1.2. In addition to the various aerodynamic parameters obtained, the flying qualities were computed for a full-scale airplane with the center-of-gravity location at 18 percent of the mean aerodynamic chord. Also, included in this investigation are drag measurements made on relatively simple fixed-control models tested with both conventional and V-tail arrangements.

Mitcham, Grady L.↗
NASA NTRS1947

Pressure-Distribution Measurements on a Straight and on a 35 Degree Swept-Back Tapered Wing

The spanwise lift-distribution measurements in straight air flow on a straight and a 35 deg swept-back tapered wing (NACA airfoil section 0012) are compared with theory for two angles of attack each (alpha approx. 6 deg and alpha approx. 12 deg) in the unstalled range of flow. The complete pressure distribution for the greater of the two angles is indicated.

Thiel, A.↗
NASA NTRS1950

Theoretical stability derivatives of thin sweptback wings tapered to a point with sweptback or sweptforward trailing edges for a limited range of supersonic speeds

The stability derivatives valid for a limited range of supersonic speeds are presented for a series of sweptback wings tapered to a point with sweptback or sweptforward trailing edges. These wings were derived by modifying the trailing edge of a basic triangular wing so that it coincided with lines drawn from the wing tips to the wing axis of symmetry. The stability derivatives were formulated by using the pressure distributions previously obtained for the basic triangular wing for angle of attack, constant vertical acceleration, sideslip, pitching, rolling, and yawing. Explicit expressions are given for the stability derivatives with respect to principal body axes, and conversion formulas are provided for the transformation to stability axes. The results are limited to Mach numbers for which the wing is contained within the Mach cones springing from the vertex and from the trailing edge of the center section of the wing.

Malvestuto, Frank S , Jr↗
NASA NTRS1954

Effects of Sweep and Thickness on the Static Longitudinal Aerodynamic Characteristics of a Series of Thin, Low-aspect-ratio, Highly Tapered Wings at Transonic Speeds : Transonic-bump Method

An investigation by the transonic-bump technique of the static longitudinal aerodynamic characteristics of a series of thin, low-aspect-ratio, highly tapered wings has been made in the Langley high-speed 7- by 10-foot tunnel. The Mach number range extended from about 0.60 to 1.18, with corresponding Reynolds numbers ranging from about 0.75 x 10(6) to 0.95 x 10(6). The angle of attack range was from -10 degrees to approximately 32 degrees.The effects on drag and lift-drag ratio of a variation in sweep angle from -14.03 degrees to 45 degrees with respect to the quarter-chord line for wings of 3-percent-chord thickness was found to be small in comparison to the effects of a variation in thickness from 2 percent chord to 4.5 percent chord for wings with 14.03 degree sweepback. For the range of variables considered, variations in plan form were considerably more important with regard to longitudinal stability characteristics than the variations in thickness. For the series of basic wings having an aspect ratio of 4, the most hearly linear pitching-moment characteristics were obtained with 26.57 degree of sweepback of the quarter-chord line. However, for the modified series of wings (obtained by clipping the tips of the original wings parallel to the plane of symmetry to give an aspect ratio of 3 and a taper ratio of 0.143), the most nearly linear pitching-moment characteristics were obtained with 36.87 degrees of sweepback. By decreasing the thickness-to-chord ratios from 0.03 to 0.02, a large increase in lift-curve slope was obtained for both the basic and modified wings. All of the wings of both series had fairly large inward shifts of the lateral center-of-pressure location (indicative of tip stalling) with increasing lift coefficient, except those wings having minimum sweepback angles.

Fournier, Paul G↗
NASA NTRS1977

Compressible laminar boundary layers with suction on swept and tapered wings

In this paper we present a numerical method for solving the compressible laminar boundary-layer equations with suction on swept and tapered wings. The method employs an efficient two-point finite-difference method to solve the governing equations, and a very convenient similarity transformation which removes the wall normal velocity as a boundary condition and places it into the governing equations as a parameter. In this way the awkward nonlinear boundary condition which couples all the variables is avoided. To test and demonstrate the method, we present a sample calculation for a typical laminar-flow-control (LFC) wing.

Kaups, K.↗
NASA NTRS1939

Pressure-distribution Measurements on a Tapered Wing with a Full-span Split Flap in Curved Flight

Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degrees pitch, -1 degree and 5 degree yaw, and with a full-span flap deflected 60 degrees. The results are given in the form of span load distributions and in calculated moment coefficients. The rolling-moment coefficients are in fairly close agreement with those derived by means of a simple approximate theory even for high deflection of the full-span flap.

Troller, TH↗
NASA NTRS1939

Pressure-distribution measurements on a tapered wing with a partial-span split flap in curved flight

Pressure-distribution tests were made on the 32-foot whirling arm of the Daniel Guggenheim Airship Institute of a tapered wing to determine the rolling and the yawing moments due to an angular velocity in yaw. The model was tested at 0 degree and 5 degree pitch; 0 degree, 5 degree, and 10 degree yaw; and with split flaps covering 25, 50, 75, and 100 percent of the wing span and deflected 60 degrees. The results are given in the form of load distributions and as calculated moment coefficients. The experimental values of rolling- and yawing- moment coefficients were in fairly close agreement with theory.

Troller, TH↗
NASA NTRS1948

Flight Investigation to Determine the Aerodynamic Characteristics of Rocket-Powered Models Representative of a Fighter-Type Airplane Configuration Incorporating an Inverse-Taper Wing and a Vee Tail

Two rocket-powered models representative of a fighter-type airplane were investigated in flight at Mach numbers up to 1.01 and 1.07 by the Langley Pilotless Aircraft Research Division at its testing station at Wallops Island, Va. These models incorporated an inverse-taper wing and a vee tail and were flown with controls undeflected and wing and stabilizer set at 0 deg incidence. Values of lateral acceleration, normal acceleration velocity, and drag were obtained by use of telemeters and a Doppler velocimeter radar unit. The results of this investigation indicated no unusual variation in the lateral acceleration characteristics. After the cessation of powered flight, the lateral oscillation quickly damped to zero. The data indicated that the airplane, at low lift coefficients, should not experience any abrupt trim changes until it attains a Mach number of 0.97. The change in normal-force coefficient associated with this trim change will amount to about 0.03 with the center of gravity located at 4.48% of the mean aerodynamic chord. At higher lift coefficients, on the basis of other data, the Mach number at which this trim change occurs would be expected to be decreased. The neutral point of the model at Mach numbers near 1.05 was estimated to fall at 45% of the mean aerodynamic chord, assuming a lift-curve slope of 0.05. A value of the static-directional-stability parameter dCn/d(psi) of approximately -0.002 was estimated for a Mach number of 0.93. The values of drag coefficient obtained from both model flights were in a good comparative agreement. The highest drag coefficient occurred at a Mach number of 1.01 and was equal to 0.044.

Alexander, Sidney R.↗