Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - EXPERIMENTAL TESTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

NASA Langley Distributed Propulsion VTOL Tilt-Wing Aircraft Testing, Modeling, Simulation, Control, and Flight Test Development

Control of complex Vertical Take-Off and Landing (VTOL) aircraft traversing from hovering to wing born flight mode and back poses notoriously difficult modeling, simulation, control, and flight-testing challenges. This paper provides an overview of the techniques and advances required to develop the GL-10 tilt-wing, tilt-tail, long endurance, VTOL aircraft control system. The GL-10 prototype's unusual and complex configuration requires application of state-of-the-art techniques and some significant advances in wind tunnel infrastructure automation, efficient Design Of Experiments (DOE) tunnel test techniques, modeling, multi-body equations of motion, multi-body actuator models, simulation, control algorithm design, and flight test avionics, testing, and analysis. The following compendium surveys key disciplines required to develop an effective control system for this challenging vehicle in this on-going effort.

Rothhaar, Paul M.↗
NASA NTRS2016

Generation of Fullspan Leading-Edge 3D Ice Shapes for Swept-Wing Aerodynamic Testing

The deleterious effect of ice accretion on aircraft is often assessed through dry-air flight and wind tunnel testing with artificial ice shapes. This paper describes a method to create fullspan swept-wing artificial ice shapes from partial span ice segments acquired in the NASA Glenn Icing Reserch Tunnel for aerodynamic wind-tunnel testing. Full-scale ice accretion segments were laser scanned from the Inboard, Midspan, and Outboard wing station models of the 65% scale Common Research Model (CRM65) aircraft configuration. These were interpolated and extrapolated using a weighted averaging method to generate fullspan ice shapes from the root to the tip of the CRM65 wing. The results showed that this interpolation method was able to preserve many of the highly three dimensional features typically found on swept-wing ice accretions. The interpolated fullspan ice shapes were then scaled to fit the leading edge of a 8.9% scale version of the CRM65 wing for aerodynamic wind-tunnel testing. Reduced fidelity versions of the fullspan ice shapes were also created where most of the local three-dimensional features were removed. The fullspan artificial ice shapes and the reduced fidelity versions were manufactured using stereolithography.

Icing↗
NASA NTRS1992

The Enhanced Flight Screener Operational Demonstration Flight Test Program

Over the years the United States Air Force has purchased several types of commercially available aircraft that have served in many different roles. Despite the requirements for significant modifications in some cases, these aircraft can often meet the needs of the Air Force while costing far less than a new aircraft development program. The 4950th Test Wing at Wright-Patterson AFB, Ohio is the center of expertise for testing commercially available aircraft for selected USAF missions. Part of the selection process requires an operational demonstration, which is a "fly-off" competition open to aircraft that any offerer may present as suitable for a specific mission. The candidate aircraft are subjected to a limited performance and flying qualities evaluation with emphasis on the operational requirements specified by the Air Force gaining command. This paper reports on the operational demonstration conducted to support a source selection to select the Enhanced Flight Screener (EFS) aircraft which will be used as a primary flight aptitude screener to replace the T-41 currently in use. During the EFS operational demonstration, eight aircraft were evaluated over a period of six weeks, making this one of the most complex fly-offs conducted by the 4950th Test Wing to date. This paper presents a management overview, test measurements and techniques, and lessons learned from this program.

Flight Testing↗
NASA NTRS2003

NASA Tech Briefs, December 2003

Topics covered include: Organic/Inorganic Hybrid Polymer/Clay Nanocomposites; Less-Toxic Coatings for Inhibiting Corrosion of Aluminum; Liquid Coatings for Reducing Corrosion of Steel in Concrete; Processable Polyimides Containing APB and Reactive End Caps; Rod/Coil Block Copolyimides for Ion-Conducting Membranes; Techniques for Characterizing Microwave Printed Antennas; Cylindrical Antenna With Partly Adaptive Phased-Array Feed; Command Interface ASIC - Analog Interface ASIC Chip Set; Predicting Accumulations of Ice on Aerodynamic Surfaces; Analyzing Aeroelasticity in Turbomachines; Software for Allocating Resources in the Deep Space Network; Expert Seeker; High-Speed Recording of Test Data on Hard Disks; Functionally Graded Nanophase Beryllium/Carbon Composites; Thin Thermal-Insulation Blankets for Very High Temperatures; Aerostructures Test Wing; Flight-Test Evaluation of Flutter-Prediction Methods; Piezoelectrically Actuated Microvalve for Liquid Effluents; Larger-Stroke Piezoelectrically Actuated Microvalve; Innovative, High-Pressure, Cryogenic Control Valve: Short Face-to-Face, Reduced Cost; Safer Roadside Crash Walls Would Limit Deceleration; Improved Interactive Medical-Imaging System; Scanning Microscopes Using X Rays and Microchannels; Slotting Fins of Heat Exchangers to Provide Thermal Breaks; Methane Clathrate Hydrate Prospecting; Automated Monitoring with a BSP Fault-Detection Test; Automated Monitoring with a BCP Fault-Decision Test; Vector-Ordering Filter Procedure for Data Reduction; Remote Sensing and Information Technology for Large Farms; Developments at the Advanced Design Technologies Testbed; Spore-Forming Bacteria that Resist Sterilization; and Acoustical Applications of the HHT Method.

Source record↗
NASA NTRS2017

Comparison of High-Fidelity Computational Tools for Wing Design of a Distributed Electric Propulsion Aircraft

A variety of tools, from fundamental to high order, have been used to better understand applications of distributed electric propulsion to aid the wing and propulsion system design of the Leading Edge Asynchronous Propulsion Technology (LEAPTech) project and the X-57 Maxwell airplane. Three high-fidelity, Navier-Stokes computational fluid dynamics codes used during the project with results presented here are FUN3D, STAR-CCM+, and OVERFLOW. These codes employ various turbulence models to predict fully turbulent and transitional flow. Results from these codes are compared for two distributed electric propulsion configurations: the wing tested at NASA Armstrong on the Hybrid-Electric Integrated Systems Testbed truck, and the wing designed for the X-57 Maxwell airplane. Results from these computational tools for the high-lift wing tested on the Hybrid-Electric Integrated Systems Testbed truck and the X-57 high-lift wing presented compare reasonably well. The goal of the X-57 wing and distributed electric propulsion system design achieving or exceeding the required 𝐶 (sub L) = 3.95 for stall speed was confirmed with all of the computational codes.

Deere, Karen A.↗
NASA NTRS1959

Free-Flight Investigation of a Rocket-Propelled Model to Determine the Aerodynamic Heating on a Thin, Unswept, Untapered, Multispar, Aluminum-Alloy Wing at Mach Numbers up to 2.22

A free-flight investigation has been made to determine some effects of aerodynamic heating on the structural behavior of a wing at supersonic speeds. The test wing was a thin, unswept, untapered, multispar, aluminum-alloy wing having a 20-inch chord, a 20-inch exposed semispan, and a circular-arc airfoil section with a thickness ratio of 5 percent. The wing was tested on a model propelled by a two-stage rocket-propulsion system to a Mach number of 2.22 and a corresponding Reynolds number per foot of 13.2 x 10(6) Reasonably good agreement was obtained between Stanton numbers obtained from measured temperature-time data and values obtained by the theory of Van Driest for flat plates having turbulent boundary layers. Temperature measurements made in the skin of the wing and in the internal structures agreed well with calculated values. The wing was instrumented to detect any apparent fluttering motion in the wing, but no evidence of flutter was observed throughout the flight.

Stephens, Emily W.↗
NASA NTRS2005

Deformation Measurements of Smart Aerodynamic Surfaces

Video Model Deformation (VMD) and Projection Moire Interferometry (PMI) were used to acquire wind tunnel model deformation measurements of the Northrop Grumman-built Smart Wing tested in the NASA Langley Transonic Dynamics Tunnel. The F18-E/F planform Smart Wing was outfitted with embedded shape memory alloys to actuate a seamless trailing edge aileron and flap, and an embedded torque tube to generate wing twist. The VMD system was used to obtain highly accurate deformation measurements at three spanwise locations along the main body of the wing, and at spanwise locations on the flap and aileron. The PMI system was used to obtain full-field wing shape and deformation measurements over the entire wing lower surface. Although less accurate than the VMD system, the PMI system revealed deformations occurring between VMD target rows indistinguishable by VMD. This paper presents the VMD and PMI techniques and discusses their application in the Smart Wing test.

Fleming, Gary A.↗
NASA NTRS1973

V/STOL tilt rotor aircraft study: Wind tunnel tests of a full scale hingeless prop/rotor designed for the Boeing Model 222 tilt rotor aircraft

The rotor system designed for the Boeing Model 222 tilt rotor aircraft is a soft-in-plane hingeless rotor design, 26 feet in diameter. This rotor has completed two test programs in the NASA Ames 40' X 80' wind tunnel. The first test was a windmilling rotor test on two dynamic wing test stands. The rotor was tested up to an advance ratio equivalence of 400 knots. The second test used the NASA powered propeller test rig and data were obtained in hover, transition and low speed cruise flight. Test data were obtained in the areas of wing-rotor dynamics, rotor loads, stability and control, feedback controls, and performance to meet the test objectives. These data are presented.

Magee, J. P.↗
NASA NTRS1976

Aerodynamic Characteristics of an A-4B Aircraft with Simulated and Actual Gunfire Damage to One Wing

The aerodynamic characteristics of a damaged McDonnell Douglas A-4B aircraft were studied in the Ames Research Center's 40- by 80-Foot Wind Tunnel. A standard fuselage and three different wings were used. The first wing tested was an undamaged one in which holes had been cut and detachable cover plates installed. Removal of one or more cover plates gave one of fourteen different simulated damage cases. The other two wings tested were damaged by actual gunfire at an Air Force range.

Betzina, M. D.↗
NASA NTRS2023

Lessons Learned from Large-Scale Aerospace Structural Testing

Large-scale testing of aerospace structures is frequently the final step in a development project to validate the structural performance, and that step typically involves a large cost and time investment. To ensure that the testing provides the required data, avoiding errors that can result in an unsuccessful test and failure to meet objectives is critical. Five lessons learned are presented herein to provide insight to those conducting tests in order to help them avoid known pitfalls that may result in an unsuccessful test. Five large-scale tests are described, and include two composite wing tests, a composite hybrid-wing body center section test, a full-scale 27.5-ft diameter metallic barrel test, and an 8-ft diameter metallic barrel test. Problems identified during the testing and mitigation approaches to solve the problems are presented, then the lessons learned are identified and discussed.

Lessons Learned↗
NASA NTRSDate not supplied

Lessons Learned from Large-Scale Aerospace Structural Testing

Large-scale testing of aerospace structures is frequently the final step in a development project to validate the structural performance, and that typically involves a large cost and time investment. In order to ensure that the testing provides the required data, avoiding errors that can result in an unsuccessful test and failure to meet objectives is critical. Presented herein are five lessons learned to provide insight to those conducting tests in order to help them avoid known pitfalls that may result in an unsuccessful test. Five subject large-scale tests are described, and include two composite wing tests, a composite hybrid-wing body center section test, a full-scale 27.5-ft diameter metallic barrel test, and an 8-ft diameter metallic barrel test. Problems identified during the testing and mitigation approaches to solve the problems are presented, then the lessons learned are summarized.

Lessons Learned↗
NASA NTRSDate not supplied

Lessons Learned from Large-Scale Aerospace Structural Testing

Large-scale testing of aerospace structures is frequently the final step in a development project to validate the structural performance, and that typically involves a large cost and time investment. In order to ensure that the testing provides the required data, avoiding errors that can result in an unsuccessful test and failure to meet objectives is critical. Presented herein are five lessons learned to provide insight to those conducting tests in order to help them avoid known pitfalls that may result in an unsuccessful test. Five subject large-scale tests are described, and include two composite wing tests, a composite hybrid-wing body center section test, a full-scale 27.5-ft diameter metallic barrel test, and an 8-ft diameter metallic barrel test. Problems identified during the testing and mitigation approaches to solve the problems are presented, then the lessons learned are summarized.

Lessons Learned↗
NASA NTRS1982

A two-degree-of-freedom flutter mount system with low damping for testing rigid wings at different angles of attack

A wind tunnel model mount system for conducting flutter research using a rigid wing was developed. The wing is attached to a splitter plate so that the two move as one rigid body. The splitter plate is supported away from the tunnel wall by a system of rods with fixed fixed and conditions. The rods flex in such a way that only pitch and plunge oscillations are permitted. At the tunnel wall the rods are attached to a remotely controlled turntable so that angle of attack can be varied. Wind tunnel data obtained by using the mount system are presented for a supercritical and a conventional airfoil. Both classical flutter and stall flutter data are presented.

Farmer, M. G.↗