Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wall Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Wall-Modeled Large-Eddy Simulations of Jet Noise in Flight Conditions

A campaign of wall-modeled large-eddy simulations (WMLES) using structured curvilinear overlapping grids has been performed with the Launch Ascent and Vehicle Aerodynamics (LAVA) computational fluid dynamics (CFD) software to predict jet noise for single-stream axisymmetric round jets. The simulations address the new Prediction Uncertainty Reduction (PUR) technical challenge within the context of NASA’s Commercial Supersonic Technology (CST) project. The focus of this effort is to generate a simulation database for single-stream axisymmetric round nozzles at several operating points both for static (no ambient co-flow), and in-flight (M ͚ =0.3 co-flow) conditions. The operating conditions range in jet exit Mach number from 0.38 to 1.1 with nozzle temperature ratios (NTR) from 0.84 to 2.7. The effect of the flight-stream on far-field noise sound spectra is assessed. Comparison of LES predictions to microphone array measurements demonstrate good agreement within the resolved frequency range. A dip in the predicted low frequency noise spectra for observers between 120° and 145° is observed. This dip is smaller for lower Mach numbers and seems to be correlated to the Mach wave radiation angle. The Mach 1.1 jet shows broadband-shock associated noise. While the onset of BBSN appears to be captured correctly in WMLES, some differences in its magnitude and the prominent frequency at which it occurs persist between the experiment and the simulations. The effect of the outer nozzle boundary layer state created by the co-flow is assessed and shows to be important for accurate comparisons with experiments. A change of 2.5dB between a slip-wall condition and a artificially thickened turbulent boundary layer was observed. In addition, simulations were performed with an alternative nozzle geometry that includes a internal plug and has twice the nozzle exit diameter. These two configurations resulted in very comparable spectra which is consistent with experimental observations. A generally stronger deviation from experimental results is observed for in-flight cases compared to static conditions. The applicability and correct usage of acoustic analogies used for far-field propagation with strong turbulent co-flows needs to be investigated more systematically using canonical problems to improve comparisons between experiments and WMLES. This is especially true for coherent noise sources seen in BBSN.

CST↗

High Order Wall-Modeled Large-Eddy Simulation on Mixed Unstructured Meshes

In the present study, an algebraic equilibrium wall model previously developed for hexahedral elements is extended to handle mixed meshes including prismatic, tetrahedral, and pyramidal elements in the context of a discontinuous high-order method. This extension is needed for complex geometries, for which high-order mixed elements (e.g., tetrahedral and pyramidal elements) are often necessary near solid walls to avoid meshing challenges. Various design decisions are discussed to achieve the best performance on massively parallel CPU/GPU architectures for a production-level high-order large-eddy simulation solver based on the flux reconstruction/correction procedure via reconstruction method, hpMusic. The extension to other elements is first evaluated using a benchmark channel flow problem at various Reynolds numbers. After that, flow over the NASA high-lift Common Research Model (CRM-HL) from the 4th AIAA High-lift Prediction Workshop is computed to further test the new implementation. Computational results at the third- and fourth-order accuracies are compared with experimental data.

Engineering↗

Jet Noise Prediction for Chevron Nozzle Flows with Wall-Modeled Large-Eddy Simulation

This paper presents results from ongoing research on jet noise prediction with wall-modeled large eddy simulations (WMLES) performed with the LAVA computational framework. In particular the focus of this study is on mixing enhancements from a single stream chevron nozzle at Reynolds number of 1×10(exp 6). Although the concept of chevron nozzles to reduce jet noise is not new, our understanding of its impact on the overall noise is still not well understood. As a first step towards predicting noise reduction due to mixing enhancement concepts from first principles with WMLES, we simulate the noise generated by a single stream chevron nozzle SMC001 as well as its equivalent axisymmetric round jet nozzle SMC000. Detailed comparisons are made with a dedicated experiment conducted at NASA’s Glenn Research Center and good agreement was achieved. Two different approaches to introduce a turbulent boundary layer were compared but show no major impact on the results. This is especially important given future work were multi-stream nozzles are considered and extended costs of resolving the internal BL would have a bigger cost impact. A permeable Ffowcs Williams Hawkings (FWH) surface enclosing the jet is used to predict far-field noise from the simulated flow-field and excellent comparison to microphone array measurements is achieved within the resolved frequency band. Sensitivity of far-field noise predictions to grid resolution is systematically documented. Near-field comparisons to PIV data shows great agreement for both velocity and normal stresses, however a systematic TKE overshoot at the nozzle exit is seen in the shear-layer. The paper shows a cost reduction of an order of magnitude compared to an earlier study of this configuration due to algorithmic and software improvements and demonstrates that WMLES can be used as a cost-competitive approach for jet noise predictions.

CST↗

Wall-Modeled LES of a Swept Wing with Leading-Edge Ice Using LAVA Curvilinear, Unstructured, and Cartesian Solvers

Wall-modeled large-eddy simulation (LES) of a swept wing with leading-edge ice build up is performed using three mesh paradigms and associated flow solvers and compared to experimental results. The study focuses on an 8.9% scale model of the CRM65 swept wing featuring both high-fidelity and smooth leading-edge ice shapes. The assessment is conducted using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework using the three actively supported meshing paradigms in LAVA: structured curvilinear overset, unstructured, andCartesian. For the iced configurations, these paradigms use hybrid body-fitted/source-term immersed-boundary, body-fitted, and ghost-cell immersed-boundary strategies, respectively.The unstructured and Cartesian mesh paradigms are particularly attractive for complex ice shapes as they avoid the manual mesh generation effort associated with the curvilinear approach. For the high-fidelity ice shape, good agreement with the experiment can be obtained with all three strategies; however, the curvilinear method is particularly sensitive to the source-term immersed-boundary timescale and span wise mesh resolution, and the Cartesian implementation is sensitive to the choice of numerical flux. For the smooth ice, larger discrepancies are observed across all methods. However, a mesh refinement study guided by flow visualizations leads to an improved comparison with the experiment that is particularly pronounced for the unstructured mesh paradigm.

TTT↗

Phenomenology of the Holographic Soft-Wall Model of QCD with 'Reversed' Dilaton

We study the phenomenology of the recently proposed modified version of the Soft-Wall model of holographic QCD with a negative dilaton profile.We investigate vector and scalar mesons, evaluating mass spectra, decay constants and two-point correlation functions. We then study chiral symmetry breaking and compute the coupling of a scalar meson with two pseudoscalars. Finally, we compare the results with the ones found in the literature in the positive-dilaton case.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

HLPW-4/GMGW-3: Wall-Modeled LES and Lattice-Boltzmann Technology Focus Group Workshop Summary

A summary of the nine submissions to the Wall-Modeled LES and Lattice-Boltzmann(WMLESLB) Technical Focus Group (TFG) at the 4th High lift Prediction Workshop is provided. The focus of this TFG was to assess the current capabilities of WMLES and Lattice-Boltzmann methods on a complex high-lift configuration across a wide range of angles of attack. Preliminary analysis of the submitted data suggests that>250𝑀spatial degrees of freedom are needed to accurately predict pitching moments at high angles of attack due to large pressure gradients present on the outboard slat and main element for𝛼 >17◦(corrected for free-air).While some scatter is reported in pitching moments at the low-angles of attack (𝛼 <11◦) - likely caused by differences in flap separation possibly due to low Reynolds number effects - excellent agreement is observed between the submissions near the𝐶𝐿,max state. Objective superiority over steady state RANS can be seen in terms of lack of excess outboard separation; a majority of the good quality WMLES and LB submissions predict wedge-shaped separation patterns consistent with the experimental oil flow. Differences in the onset of stall mechanism in the free-air configuration for𝛼 >20◦is reported with two distinct topologies observed. Topology A is characterized by the onset of corner-flow separation which progressively grows to produce a pitch break in free-air with an angle of attack increase from𝛼=20.55◦to𝛼=21.47◦+𝜖where𝜖is a small perturbation (varying between submissions and likely to be within±0.3◦). Topology Bis characterized by boundary layer weakness emanating from the inboard side of the wing-pylon juncture substantially larger than any weakness in the wing-body juncture (due to corner-flow);submissions in this category do not show any tendency for occurrence of a pitch break for the free-air configuration within the vicinity of𝛼=21.47◦. The in-tunnel simulations submitted by3 participants using different discretizations, grids and closure models show excellent agreement with the experiment in terms of a) integrated loads, b) surface flow-topology, and c) mechanism for the onset of inboard stall. Further evidence is provided to demonstrate both qualitative and quantitative superiority of all 3 WMLES submissions over a single steady state RANS submission to the workshop.

TTT↗

HLPW-4: Wall-Modeled LES and Lattice-Boltzmann Technology Focus Group Workshop Summary

A summary of the nine submissions to the Wall-Modeled LES and Lattice-Boltzmann(WMLESLB) Technical Focus Group (TFG) at the 4th High lift Prediction Workshop is provided. The focus of this TFG was to assess the current capabilities of WMLES and LB methods on a complex high-lift configuration across a wide range of angles-of-attack. Analysis of the submitted data suggests that>250𝑀spatial degrees of freedom are needed to accurately predict pitching moments at high angles-of-attack due to large pressure gradients present on the outboard slat and main element for 𝛼 >17◦(corrected for free-air). While some scatter is reported in pitching moment coefficient at the low-angles of attack (𝛼 <11◦) - excellent agreement is observed between submissions near the 𝐶𝐿,max state. Objective superiority of WMLES methods over RANS can be seen in terms of lack of excess outboard separation; a majority of the WMLES and LB submissions predict wedge-shaped separation patterns consistent with the experimental oil flow. The in-tunnel simulations show excellent agreement with the experiment in terms of a) integrated loads, b) surface flow-topology, and c) mechanism for the onset of inboard stall. Further evidence is provided to demonstrate both qualitative and quantitative superiority of the WMLES submissions over RANS.

TTT↗

Wall-Modeled Large-Eddy Simulations of a Swept Wing with Leading-Edge Ice

The aerodynamic performance of a swept wing derived from the Common Research Model wing with high-fidelity and smooth leading-edge ice shapes is evaluated using wall-modeled large-eddy simulations. Two mesh paradigms are considered within the Launch, Ascent, and Vehicle Aerodynamics framework: structured hybrid curvilinear body-fitted/immersed-boundary and unstructured Voronoi. The curvilinear approach models the effect of the ice on the flow through penalty terms and the Voronoi strategy includes the ice representation directly in the mesh.Aerodynamic loads, surface pressure profiles, and skin-friction streamlines are compared against experimental results collected at the Wichita State University wind tunnel at a Mach number of 0.18 and a Reynolds number per mean aerodynamic chord of 1.6 million. For the curvilinear simulations with high-fidelity ice, results are sensitive to spanwise mesh resolution near the leading edge, where insufficient spanwise resolution leads to a spanwise running vortexaft of the high-fidelity ice, which is partially removed with increasing spanwise resolution. For the Voronoi simulations with high-fidelity ice, refining the mesh led to good convergence towards the experimental results with the best case demonstrating a maximum discrepancy of three lift counts relative to the experiment across a range of angles of attack from about 5 to 24 degrees, validating the shrink-wrapping procedure used for the ice. For the smooth ice, the curvilinear approach consistently under-predicted the upper surface suction leading to an under-prediction in lift, but did not demonstrate the pronounced over-prediction in upper surface suction near the leading edge observed in the Voronoi simulations.

AATT↗

Domain wall model in the galactic Bose-Einstein condensate halo

We assume that the galactic dark matter halo, considered composed of an axionlike particles Bose-Einstein condensate [1], can present topological defects, namely domain walls, arising as the dark soliton solution for the Gross-Pitaevskii equation in a self-graviting potential. We investigate the influence that such substructures would have in the gravitational interactions within a galaxy. We find that, for the simple domain wall model proposed, the effects are too small to be identified, either by means of a local measurement of the gradient of the gravitational field or by analysing galaxy rotation curves. In the first case, the gradient of the gravitational field in the vicinity of the domain wall would be 10{sup −31} (m/s{sup 2})/m. In the second case, the ratio of the tangential velocity correction of a star due to the presence of the domain wall to the velocity in the spherical symmetric case would be 10{sup −8}.

79 ASTRONOMY AND ASTROPHYSICS↗

Unsteady CFD Simulations of a Compression Corner Geometry Using Wall-Modeled LES Methods in Loci/CHEM

As computing technology continues to improve, simulating unsteady aerodynamic environments on launch vehicle geometries becomes more viable. For NASA’s Space Launch System, the flowfield is characterized by large regions of unsteady turbulent wall-bounded flow. Simulating these unsteady wall-bounded environments is of interest to the SLS Aerodynamics team. Wall-modeled LES methods are currently the best approach for simulating these environments in engineering applications. Less-expensive computationally than fully-resolved methods while maintaining many of the benefits in simulating unsteady environments. Before applying these methods blindly to large geometries, best practices can first be applied and understood on smaller canonical problems.

Bryson Frank↗

Structural uncertainty assessment for fire-engulfed objects in crosswind: Establishing credibility for a multiphysics wall-modeled large-eddy simulation paradigm

A structural uncertainty validation study for a large-scale, fire-engulfed, elevated object subjected to crosswind is presented to establish the credibility of a high-fidelity, low-Mach, turbulent reacting flow wall-modeled large-eddy simulation (WMLES) approach that includes multiphysics coupling to participating media radiation and conjugate heat transfer. To establish that WMLES can accurately predict surface quantities including drag and pressure coefficient in the low-Mach crosswind regime, a foundational elevated isothermal cylinder validation case is presented at a similar gap-to-diameter ratio of 0.25, spanning the subcritical to supercritical drag regime (Re 𝐷 = 1.1 × 10 5 and 4.3 × 10 5 , respectively). Here, this study exercised both static and dynamic coefficient LES (Smagorinsky and 𝑘 sgs ) with both local and exchange-based velocity sampling. Results showcase that the drag crisis (or the sudden drop in drag coefficient at increased Re 𝐷 ) is well captured when using an exchange-based dynamic coefficient WMLES methodology, while noting lack of mesh convergence and overall drag and pressure coefficient predictively when using a static coefficient, local velocity sampling WMLES. For the 𝒪⁡(10) m JP-8 liquid pool fire crosswind validation study presented, two experimental crosswind configurations (2 m/s and 9.5 m/s) are showcased for a fire-engulfed mock fuselage roughly 4 m in diameter. Using the best model-form practices identified in the isothermal study, dynamic coefficient 𝑘 sgs exchange-based WMLES fire validation findings demonstrate accurate peak irradiation and skin temperature predictions as a function of crosswind magnitude. Excessive yaw in the low-crosswind fuselage configuration, consistent with experimental findings, captured a significant predicted asymmetry in flame attachment and heat flux toward the downwind cylindrical cap—indicative of axial vortex structures transporting the flame along the upper and lower fuselage leeward surface. All fire mesh resolution simulations captured the experimental finding that as crosswind increased, predicted flame shape and peak irradiation magnitude onto the fuselage transitioned from a windward to a leeward cylinder location due to the migration of the upper- to lower-shear fuel/air mixing layer thereby demonstrating the novelty, significance, and credibility of this high-fidelity WMLES reacting flow framework.

Domino, Stefan Paul [Sandia National Laboratories ↗

Wall-Modeled Large Eddy Simulations of Transonic Buffet Over a Supercritical Airfoil

A series of scale-resolving simulations of flow over the ONERA OAT15A airfoil have been performed at an angle of attack of 3.5◦, just past the onset of buffet. The focus of this study is to document the sensitivity of the wall-modeled large eddy simulation (WMLES) methodology for curvilinear structured overset grids within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) framework to mesh spacing, mesh distribution, and domain size. A secondary purpose of the study is to compare the results from WMLES to unsteady Reynolds-averaged Navier Stokes (URANS) simulations and hybrid RANS-LES (HRLES) within the same LAVA solver framework. The study provides a unique perspective regarding comparisons between different turbulence modeling approaches, time-integration methods, and computational performance since many of the same numerical routines are used for all three types of simulations. The results are compared with experiments and previous numerical studies of the same geometry and flow conditions.

TTT↗

LAVA Voronoi Mesher for Wall-Modeled Large-Eddy Simulations

The unstructured Voronoi mesher currently being developed within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) software framework at NASA Ames Research Center is described in detail. The discussions include, but are not limited to, the strategies used in the seeding and smoothing phases to ensure a high-quality mesh for Wall-Modeled Large-Eddy Simulations (WMLES), the methods behind the cell clipping algorithm responsible for conforming the mesh to a complex geometry, and the approach to create a global mesh from the distinct Voronoi cells. Applications and benefits of the Voronoi meshing approach are also presented. The automated meshing paradigm introduced was able to significantly reduce the time necessary to create a high-quality mesh around a complex geometry when compared against the current LAVA curvilinear overset meshing standard. For example, the task of generating a single mesh around the high-lift common research model requires the full dedication of a mesh generation expert for a period between one and two months. A family of meshes with different refinement levels up to six hundred million cells can be generated by a single engineer in a day or two. This technology has the potential for decreasing the turnaround time for conducting WMLES around complex geometries, as well as facilitating comprehensive mesh refinement studies.

Victor C B Sousa↗

Inverse-Velocity Transformation Wall Model for Reacting Turbulent Hypersonic Boundary Layers

The present study builds on prior work by taking advantage of the novel framework proposed by Griffin et al. (hereafter referred to as the GFM) as a baseline. The model is progressively extended to multicomponent reacting mixtures, accounting for differential diffusion and finite-rate chemistry in a similar fashion to Di Renzo & Urzay and Di Renzo et al. The accuracy of the present approach, as well the prior model of Di Renzo & Urzay, is assessed in an a priori sense for the first time in a turbulent reacting boundary layer, using the boundary-layer data of Williams et al. Five species are included in the present analysis, i.e., N s = 5, namely N 2 , O 2 , NO, N and O, a neutral mixture most representative of dissociation/recombination phenomena for temperatures below 6000 K. A schematic of a flow over a wedge representative of the described configuration is presented in Figure 1. The brief is organized as follows: In Section 2, the wall-model equations and the computational framework are presented. In Section 3, the a priori results of the proposed model are described and compared to the extended EWM. Finally, in Section 4, some conclusions are offered.

97 MATHEMATICS AND COMPUTING↗

Near-wall modeling of compressible turbulent flow

A near-wall two-equation model for compressible flows is proposed. The model is formulated by relaxing the assumption of dynamic field similarity between compressible and incompressible flows. A postulate is made to justify the extension of incompressible models to ammount for compressibility effects. This requires formulation the turbulent kinetic energy equation in a form similar to its incompressible counterpart. As a result, the compressible dissipation function has to be split into a solenoidal part, which is not sensitive to changes of compressibility indicators, and a dilatational part, which is directly affected by these changes. A model with an explicit dependence on the turbulent Mach number is proposed for the dilatational dissipation rate.

So, Ronald M. C.↗

Diffusion in intact secondary cell wall models of plants at different equilibrium moisture content

Secondary plant cell walls are composed of carbohydrate and lignin polymers, and collectively represent a significant renewable resource. Leveraging these resources depends in part on a mechanistic understanding for diffusive processes within plant cell walls. Common wood protection treatments and biomass conversion processes to create biorefinery feedstocks feature ion or solvent diffusion within the cell wall. X-ray fluorescence microscopy experiments have determined that ionic diffusion rates are dependent on cell wall hydration as well as the ionic species through non-linear relationships. In this work, we use classical molecular dynamics simulations to map the diffusion behavior of different plant cell wall components (cellulose, hemicellulose, lignin), ions (Na + , K + , Cu2 + , Cl - ) and water within a model for an intact plant cell wall at various hydration states (3-30 wt% water). From these simulations, we analyze the contacts between different plant cell wall components with each other and their interaction with the ions. Generally, diffusion increases with increasing hydration, with lignin and hemicellulose components increasing diffusion by an order of magnitude over the tested hydration range. Ion diffusion depends on charge. Positively charged cations preferentially interact with hemicellulose components, which include negatively charged carboxylates. As a result, positive ions diffuse more slowly than negatively charged ions. Measured diffusion coefficients are largely observed to best fit piecewise linear trends, with an inflection point between 10 and 15% hydration. These observations shed light onto the molecular mechanisms for diffusive processes within secondary plant cell walls at atomic resolution.

09 BIOMASS FUELS↗