Search NASA⌕ Search

SEARCH · Search NASA

Results for “Well Test Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Aspects of supercritical wing theory

Concepts and techniques that have proved successful in the computational theory of shockless airfoils are examined. Shockless airfoils have been used in the design of supercritical wings for fuel-efficient aircraft. In transonic aerodynamics, it is has been found that test data agree well with the best results obtained from CFD. This is particularly true for two-dimensional flow, where accurate experiments are difficult to perform and numerical calculations are relatively easy. However, it is important to choose reasonable models in setting up the computations. Particular attention is given to the formulation of the relevant differential equations in ways that have been found to be satisfactory in practice.

Garabedian, P. R.↗
NASA NTRS1988

Stress concentration around circular hole in a composite material specimen representative of the X-29A forward-swept wing aircraft

The theory of anisotropic elasticity was used to evaluate the anisotropic stress concentration factors of a composite laminated plate containing a small circular hole. This advanced composite material was used to manufacture the X-29A forward swept wing. Observe that the usual isotropic material stress concentration factor is three. However, for composite material, it was found that the anisotropic stress concentration factor is no longer constant, and that the locations of maximum tangential stress points could shift by changing the fiber orientation with respect to the loading axis. The analysis showed that through the lamination process, the stress concentration factor could be drastically reduced, and therefore the structural performance could be improved. Both the mixture rule approach and the constant strain approach were used to calculate the stress concentration factor. The results predicted by the mixture rule approach were about 20 percent deviate from the experimental data. However, the results predicted by the constant strain approach matched the testing data very well. This showed the importance of the inplane shear effect on the evaluation of stress concentration factor for the X-29A composite plate.

Yeh, Hsien-Yang↗
NASA NTRS1988

Temperature effect on stress concentration around circular hole in a composite material specimen representative of X-29A forward-swept wing aircraft

The theory of anisotropic elasticity was used to evaluate the anisotropic stress concentration factors of a composite laminated plate containing a small circular hole. This advanced composite was used to manufacture the X-29A forward-swept wing. It was found for composite material, that the anisotropic stress concentration is no longer a constant, and that the locations of maximum tangential stress points could shift by changing the fiber orientation with respect to the loading axis. The analysis showed that through the lamination process, the stress concentration factor could be reduced drastically, and therefore the structural performance could be improved. Both the mixture rule approach and the constant strain approach were used to calculate the stress concentration factor of room temperature. The results predicted by the mixture rule approach were about twenty percent deviate from the experimental data. However, the results predicted by the constant strain approach matched the testing data very well. This showed the importance of the inplane shear effect on the evaluation of the stress concentration factor for the X-29A composite plate.

Yeh, Hsien-Yang↗
NASA NTRS1990

Flare heating and ionization of the low solar chromosphere. I - Inversion methods for Mg I 4571 and 5173

Various methods of inverting solar Mg I 4571 and 5173 spectral line observations are examined to find the best method of using these lines to calculate the vertical temperature and electron density structure around the temperature minimum region. Following a perturbation analysis by Mein (1971), a Fredholm integral equation of the first kind is obtained which can be inverted to yield these temperature and density structures as a function of time. Several inversion methods are tested and compared. The methods are used to test data as well as to a subset of observations of these absorption lines taken on February 3, 1986 before and during a solar flare. A small but significant increase is found in the temperature and a relatively large increase in the electron density during this flare. The observations are inconsistent with heating and ionization by an intense beam of electrons and with ionization by UV photoionization of Si I.

Metcalf, Thomas R.↗
NASA NTRS1991

Low cost attitude control system scanwheel development

In order to satisfy a growing demand for low cost attitude control systems for small spacecraft, development of low cost scanning horizon sensor coupled to a low cost/low power consumption Reaction Wheel Assembly was initiated. This report addresses the details of the versatile design resulting from this effort. Tradeoff analyses for each of the major components are included, as well as test data from an engineering prototype of the hardware.

Bialke, William↗
NASA NTRS1993

A fracture criterion for widespread cracking in thin-sheet aluminum alloys

An elastic-plastic finite-element analysis was used with a critical crack-tip-opening angle (CTOA) fracture criterion to model stable crack growth in thin-sheet 2024-T3 aluminum alloy panels with single and multiple-site damage (MSD) cracks. Comparisons were made between critical angles determined from the analyses and those measured with photographic methods. Calculated load against crack extension and load against crack-tip displacement on single crack specimens agreed well with test data even for large-scale plastic deformations. The analyses were also able to predict the stable tearing behavior of large lead cracks in the presence of stably tearing MSD cracks. Small MSD cracks significantly reduced the residual strength for large lead cracks.

Newman, J. C., Jr.↗
NASA NTRS1991

Low cost attitude control system reaction wheel development

In order to satisfy a growing demand for low cost attitude control systems for small spacecraft, development of a low power and low cost Reaction Wheel Assembly was initiated. The details of the versatile design resulting from this effort are addressed. Tradeoff analyses for each of the major components are included, as well as test data from an engineering prototype of the hardware.

Bialke, William↗
NASA NTRS1996

Overset Grid Methods for Multidisciplinary Applications in Rotorcraft Problems

A methodology for the coupling of an advanced computational fluid dynamics method based on an overset grid flow-solver and an advanced computational structural dynamics method based on a finite element analysis is presented. Various procedures for the fluid-structure interactions modeling along with their limitations are also discussed. The flight test data for the four-bladed UH-60A Blackhawk helicopter rotor is chosen for the validation of the results. Convergence and accuracy are tested by numerical experiments with a single-bladed rotor. A comparison of airload predictions with flight test data as well as with a rigid blade case is presented. Grid and interpolation related issues for this aeroelastic application are described.

Ahmad, J. U.↗
NASA NTRS1997

Prediction of Crack Growth under Variable-Amplitude Loading in Thin-Sheet 2024-T3 Aluminum Alloys

The present paper is concerned with the application of a "plasticity-induced" crack closure model to study fatigue crack growth under various load histories. The model was based on the Dugdale model but modified to leave plastically deformed material in the wake of the advancing crack. The model was used to correlate crack growth rates under constant-amplitude loading and then used to predict crack growth under variable-amplitude and spectrum loading on thin-sheet 2024- T3 aluminum alloys. Predicted crack-opening stresses agreed well with test data from the literature. The crack-growth lives agreed within a factor of two for single and repeated spike overloads/underloads and within 20 percent for spectrum loading. Differences were attributed to fretting-product-debris-induced closure and three-dimensional affects not included in the model.

Newman, J. C., Jr.↗
NASA NTRS2007

Evaluation of a Highly Anticlastic Panel with Tow Overlaps

A rectangular, variable-stiffness panel with tow overlaps was manufactured using an advanced tow placement machine. The cured panel had large anticlastic imperfections, with measured amplitudes of over two times the average panel thickness. These imperfections were not due to the overall steered-fiber layup or the tow overlaps, but instead resulted from local asymmetries in the laminate that were caused by a manufacturing oversight. In the nominal panel layup, fiber angles vary linearly from 60 degrees on the panel axial centerline to 30 degrees on the parallel edges. A geometrically nonlinear analysis was performed with a -280 degree Fahrenheit thermal load to simulate the postcure cooldown to room temperature. The predicted geometric imperfections correlated well with the measured panel shape. Unique structural test fixtures were then developed which greatly reduced these imperfections, but they also caused prestresses in the panel. Surface imperfections measured after the panel was installed in the test fixtures were used with nonlinear finite element analyses to predict these fixturing-induced prestresses. These prestresses were also included in structural analyses of panel end compression to failure, and the analytical results compared well with test data when both geometric and material nonlinearities were included.

Wu, K. Chauncey↗
NASA NTRS2014

Prospects for Chlorophyll Fluorescence Remote Sensing from the Orbiting Carbon Observatory-2

The Orbiting Carbon Observatory-2 (OCO-2), scheduled to launch in July 2014, is a NASA mission designed to measure atmospheric CO2. Its main purpose is to allow inversions of net flux estimates of CO2 on regional to continental scales using the total column CO2 retrieved using high-resolution spectra in the 0.76, 1.6, and 2.0 nm ranges. Recently, it was shown that solar-induced chlorophyll fluorescence (SIF), a proxy for gross primary production (GPP, carbon uptake through photosynthesis), can be accurately retrieved from space using high spectral resolution radiances in the 750 nm range from the Japanese GOSAT and European GOME-2 instruments. Here, we use real OCO-2 thermal vacuum test data as well as a full repeat cycle (16 days) of simulated OCO-2 spectra under realistic conditions to evaluate the potential of OCO-2 for retrievals of chlorophyll fluorescence and also its dependence on clouds and aerosols. We find that the single-measurement precision is 0.3-0.5 Wm(exp -2)sr(exp -1) nm(exp -1) (15-25% of typical peak values), better than current measurements from space but still difficult to interpret on a single-sounding basis. The most significant advancement will come from smaller ground-pixel sizes and increased measurement frequency, with a 100-fold increase compared to GOSAT (and about 8 times higher than GOME-2). This will largely decrease the need for coarse spatial and temporal averaging in data analysis and pave the way to accurate local studies.We also find that the lack of full global mapping from the OCO-2 only incurs small representativeness errors on regional averages. Eventually, the combination of net ecosystem exchange (NEE) derived from CO2 source/sink inversions and SIF as proxy for GPP from the same satellite will provide a more process-based understanding of the global carbon cycle.

vegetation agriculture satellite↗
NASA NTRS2023

Numerical Study of Solidification Crack Susceptibility in Novel Refractory Alloy Systems

Calculation of Phase Diagrams (CALPHAD) -based solidification computa­tions, such as Scheil or equilibrium computations, have been utilized to propose crack solidification susceptibility indices (CSSIs) of cracking. These CSSIs have been proposed in order to predict the cracking susceptibility of an alloy in the solidification range, as a function of its solidification frac­tion and as dependent upon its wt.% elemental composition through the CALPHAD computation & via comparative methods between one composition & the next. Recently Kou at al. have proposed a novel CSSI where the gradient of the e.x. Scheil solidification curve is obtained in the critical solidification cracking region of greater than 0.95 fraction of solid. Therefore, a direct Temperature dependent metric is now available for the prediction, and presumably the control, of solidification cracking. In this TM, the researchers apply this Kou gradient method to refractory alloys for the first time & discuss justification for the approach via Spearman rank correlation with Varestraint cracking test data as well as by comparisons with Thermocalc based vulnerability time CSSI calculations. A Python Pycalphad module example of the approach is provided & can be utilized as an open-source resource that utilizes also open-source available thermodynamical databases, making the CSSI quantitative aspect of ICME more available and freely available to practitioners.

ICME integrated computational materials engineerin↗
DOE OSTI2025

Experimental Validation of Exact Burst Pressure Solutions for Thick-Walled Cylindrical Pressure Vessels

Burst pressure is one of the critical strength parameters used in the design and operation of pressure vessels because it represents the maximum pressure that a vessel can withstand before failing. Historically, the Barlow formula was used as a design base for estimating burst pressure. However, it does not consider the plastic flow response for ductile steels and is applicable only to thin-walled cylinders (i.e., the diameter to thickness ratio D/t ≥ 20). A new multiaxial plastic yield theory was developed to consider the plastic flow response, and the associated theoretical (i.e., Zhu–Leis) solution of burst pressure was obtained and has gained extensive applications in the pipeline industry because it was validated by different full-scale burst test datasets for large-diameter, thin-walled pipelines in a variety of steel grades from Grade B to X120. The Zhu–Leis flow theory of plasticity was recently extended to thick-walled pressure vessels, and the associated exact flow solution of burst pressure was obtained and is applicable to both thin and thick-walled cylindrical shells. Many full-scale burst tests are available for thin-walled line pipes in the pipeline industry, but limited pressure burst tests exist for thick-walled vessels. To validate the newly developed exact solutions of burst pressure for thick-walled cylinders, this paper conducts a series of burst pressure tests on small-diameter, thick-walled pipes. In particular, six burst tests are carried out for three thick-walled pipes in Grade B carbon steel. These pipes have a nominal diameter of 2.375 inches (60.33 mm) and three nominal wall thicknesses of 0.154, 0.218, and 0.344 inches (3.91, 5.54, and 8.74 mm), leading to D/t = 15.4, 10.9, and 6.9, respectively. With the burst test data, comparisons show that the Zhu–Leis flow solution of burst pressure matches well the burst test data for thick-walled pipes. Thus, these burst tests validate the accuracy of the Zhu–Leis flow solution of burst pressure for thick-walled cylindrical vessels.

42 ENGINEERING↗
NASA NTRS2023

Finite Element Model Tuning using Analytical Sensitivity Values

This paper presents an efficient approach for tuning finite element models to match the measured ground vibrationtest and proof test data. Frequencies, mode shapes, total weight, location of the center of gravity, and staticdeformation computed from the finite element model are matched to the measured data. The model tuningprocedure used in this work is based on solving an optimization problem in which the errors for the consideredmetrics, between the finite element prediction and the measured data, are minimized. Analytical sensitivity values ofperformance indices are computed using the NASTRAN-generated sensitivity values together with the in-housecomputer programs, which allow for faster computational time and the use of gradient-based optimizers. The methodis applied to the Aerostructures Test Wing 4 model. The study shows that the military standard and the NASAstandard for comparing analytical and experimental modal data are all satisfied. The final finite element modelcorrelates well with the test data. The flutter speed decreases by 8.91% after model tuning compared with the original Aerostructures Test Wing 4 design.

Chan-gi Pak↗
NASA NTRSDate not supplied

Using Distributed Fiber-optic Strain Sensing to Estimate Generalized Modal Coordinates from Flight-test Data

A method for estimating the generalized modal coordinates of an aircraft during flight has been developed. The Fiber-optic Sensing System (FOSS) offers an efficient and cost-effective method of measuring the strain at thousands of points along the wings. The estimation of modal coordinates was implemented as a two-step process. First, a maximum likelihood method is used to estimate the statistical properties of the sensors and generalized modal coordinates. Second, the strain mode shapes from the finite element model are used along with the statistical properties from the first step to estimate the generalized modal coordinates over time. Using simulated data from the X-56A Multi-Utility Technology Testbed (MUTT), different methods of modal coordinate estimation were compared to demonstrate the benefits and weaknesses of each. These were compared against the exact solution and an ordinary least squares (a more traditional method) estimate. Modal coordinate estimation methods were then applied to flight-test data from the X-56A aircraft to show that the method continues to work well with actual test data. The new estimation method provides insights unavailable from more classical approaches.

Jeffrey Ouellette↗
NASA NTRS2013

Sasquatch Footprint Tool

The Crew Exploration Vehicle Parachute Assembly System (CPAS) is the parachute system for NASA s Orion spacecraft. The test program consists of numerous drop tests, wherein a test article rigged with parachutes is extracted or released from an aircraft. During such tests, range safety is paramount, as is the recoverability of the parachutes and test article. It is crucial to establish an aircraft release point that will ensure that the article and all items released from it will land in safe locations. A new footprint predictor tool, called Sasquatch, was created in MATLAB. This tool takes in a simulated trajectory for the test article, information about all released objects, and atmospheric wind data (simulated or actual) to calculate the trajectories of the released objects. Dispersions are applied to the landing locations of those objects, taking into account the variability of winds, aircraft release point, and object descent rate. Sasquatch establishes a payload release point (e.g., where the payload will be extracted from the carrier aircraft) that will ensure that the payload and all objects released from it will land in a specified cleared area. The landing locations (the final points in the trajectories) are plotted on a map of the test range. Sasquatch was originally designed for CPAS drop tests and includes extensive information about both the CPAS hardware and the primary test range used for CPAS testing. However, it can easily be adapted for more complex CPAS drop tests, other NASA projects, and commercial partners. CPAS has developed the Sasquatch footprint tool to ensure range safety during parachute drop tests. Sasquatch is well correlated to test data and continues to ensure the safety of test personnel as well as the safe recovery of all equipment. The tool will continue to be modified based on new test data, improving predictions and providing added capability to meet the requirements of more complex testing.

Bledsoe, Kristin↗
NASA NTRS1989

Working group written presentation: Solar radiation

The members of the Solar Radiation Working Group arrived at two major solar radiation technology needs: (1) generation of a long term flight data base; and (2) development of a standardized UV testing methodology. The flight data base should include 1 to 5 year exposure of optical filters, windows, thermal control coatings, hardened coatings, polymeric films, and structural composites. The UV flux and wavelength distribution, as well as particulate radiation flux and energy, should be measured during this flight exposure. A standard testing methodology is needed to establish techniques for highly accelerated UV exposure which will correlate well with flight test data. Currently, UV can only be accelerated to about 3 solar constants and can correlate well with flight exposure data. With space missions to 30 years, acceleration rates of 30 to 100X are needed for efficient laboratory testing.

Slemp, Wayne S.↗