Search NASA⌕ Search

SEARCH · Search NASA

Results for “Windmilling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1927

Testing a Windmill Airplane ("autogiro")

In order to clear up the matter ( In the Spanish report it was stated that the reference surface for the calculation of the coefficients c(sub a) and c(sub w) was the area of all four wings, instead of a single wing), the model of a windwill airplane was tested in the Gottingen wind tunnel.

AIRPLANES, WIND TUNNEL TESTS - AUTOGIROS, WIND TUN↗
NASA NTRS1981

Scale model studies for improvement of flow patterns of a low-speed tunnel

Flow along a nacelle was investigated with and without an orifice plate inserted into the airstream. The flow became more uniform in transit through the orifice when compared with the upstream flow and remained more uniform immediately downstream from the orifice. No improvement was found farther downstream with or without the orifice plate. Various windmills were studied to determine their effects on the downstream flow pattern. The windmill retarded flow velocity inside the circle inscribed by the tip of free wheeling propellers (used as substitute windmills), while the main stream passed over the blades seemingly unrestricted and without showing any increase in diameter. Results show that by varying a torque, the flow across a windmill can be effectively redistributed, an effect that could be gainfully employed in situations where the main flow into a diffuser is concentrated near the center. The construction of the 1/24 scale model tunnel and the velocity transverses obtained on the model are discussed. The transverses indicate that the velocity distribution may be considered worse in the vertical than in the horizontal plane.

Barna, P. S.↗
NASA NTRS1954

Altitude Performance and Operational Characteristics of an XT38-A-2 Turboprop Engine

The overall engine performance and the starting and windmilling characteristics of an XT38-A-2 turboprop engine have been investigated in the NACA Lewis altitude wind tunnel. The simulated flight conditions ranged from altitudes of 5000 to 45,000 feet at a flight Mach number of 0.30 and from Mach numbers of 0.301 to 0.557 at an altitude of 35,000 feet. The engine, equipped with a standard-area exhaust nozzle, was operated with independent control of fuel flow and propeller pitch; operation was thereby allowed over a wide range of engine conditions. Windmilling characteristics were obtained at altitudes of 15,000 feet and 35,000 feet. Analysis of the performance maps obtained at each flight condition revealed that both altitude and flight Mach number had a major effect on corrected engine variables. The large reductions in corrected shaft horsepower occurring when the altitude was increased were the result of decreases in compressor and turbine efficiencies. Windmilling engine starts were made at altitudes as high as 35,000 feet at an engine speed of 2000 rpm.

Essig, R H↗
NASA NTRS1973

Wind power demonstration and siting problems

Technical and economic feasibility studies on a small windmill to provide overnight charging for an electrically driven car are reported. The auxiliary generator provides power for heating and cooling the vehicle which runs for 25 miles on battery power alone, and for 50 miles with the onboard charger operating. The blades for this windmill have a diameter of 12 feet and are coupled through to a conventional automobile alternator so that they are able to completely recharge car batteries in 8 hours. Optimization of a windmill/storage system requires detailed wind velocity information which permits rational sitting of wind power system stations.

Bergey, K. H.↗
NASA NTRS1975

Wind power

A historical background on windmill use, the nature of wind, wind conversion system technology and requirements, the economics of wind power and comparisons with alternative systems, data needs, technology development needs, and an implementation plan for wind energy are presented. Considerable progress took place during the 1950's. Most of the modern windmills feature a wind turbine electricity generator located directly at the top of their rotor towers.

Savino, J. M.↗
NASA NTRS1976

Flap-augmented shrouds for aerogenerators

Axisymmetrical shrouds for windmills are augmented by ring-shaped 'flaps' and their performance is studied experimentally. The concept of the shroud as an annular 'wing' is justified, leading to the conclusion that high-lift techniques should be used in shroud design, and that high-lift devices, such as flaps, would increase the power output of the windmill. It is shown experimentally that the ideal power output of a flap-augmented shrouded turbine can be more than 4 times the power of unshrouded turbines of the same diameter.

Seginer, A.↗
NASA NTRS1981

Wind speed statistics for Goldstone, California, anemometer sites

An exploratory wind survey at an antenna complex was summarized statistically for application to future windmill designs. Data were collected at six locations from a total of 10 anemometers. Statistics include means, standard deviations, cubes, pattern factors, correlation coefficients, and exponents for power law profile of wind speed. Curves presented include: mean monthly wind speeds, moving averages, and diurnal variation patterns. It is concluded that three of the locations have sufficiently strong winds to justify consideration for windmill sites.

Berg, M.↗
NASA NTRS1952

Performance and Operational Characteristics of a Python Turbine-propeller Engine at Simulated Altitude Conditions / Carl L. Meyer and Lavern A. Johnson

The performance and operational characteristics of a Python turbine propeller engine have been investigated over a range of engine operating conditions at simulated altitudes from 5000 to 40,000 feet in the NACA Lewis altitude wind tunnel . For the performance phase of the investigation, a single cowl-inlet ram pressure ratio was maintained and independent control of engine speed and fuel flow was used to obtain a range of power at each engine speed. Engine performance data obtained at a given altitude could not be used to predict performance accurately at other altitudes by use of the standard air pressure and temperature generalizing factors. Specific fuel consumption based on shaft horsepower decreased as the shaft horsepower increased at a given engine speed. At a given altitude condition and turbine -inlet total temperature, there was an optimum engine speed at which maximum shaft horsepower was obtained. At a given engine speed and turbine-inlet total temperature, a greater portion of the total available energy was converted to propulsive power as the altitude increased. Windmilling starts were made at altitudes up to 40,000 feet; the minimum true airspeed required for successful windmilling starts increased as the altitude was raised. In general, the engine control prevented large overshoots or undershoots of engine speed during starts, accelerations, and decelerations.

Engines - Armstrong-Siddely Python Turbo-Propeller↗
NASA NTRS1952

Investigation of Spinning and Tumbling Characteristics of a 1/20-Scale Model of the Consolidated Vultee XFY-1 Airplane in the Free-Spinning Tunnel, TED No. NACA DE 370

An investigation has been conducted in the Langley 20-foot free-spinning tunnel on a l/20-scale model of the Consolidated Vultee XFY-1 airplane with a windmilling propeller simulated to determine the effects of control setting and movements upon the erect spin and recovery characteristics for a range of airplane-loading conditions. The effects on the model's spin-recovery characteristics of removing the lower vertical tail, removing the gun pods, and fixing the rudders at neutral were also investigated briefly. The investigation included determination of the size parachute required for emergency recovery from demonstration spins. The tumbling tendencies of the model were also investigated. Brief static force tests were made to determine the aerodynamic characteristics in pitch at high angles of attack. The investigation indicated that the spin and recovery characteristics of the airplane with propeller windmilling will be satisfactory for all loading conditions if recovery is attempted by full rudder reversal accompanied by simultaneous movement of the stick laterally to full with the spin (stick right in a right spin) and longitudinally to neutral. Inverted spins should be satisfactorily terminated by fully reversing the rudder followed immediately by moving the stick laterally towards the forward rudder pedal and longitudinally to neutral. Removal of the gun pods or fixing the rudders at neutral will not adversely affect the airplane's spin-recovery characteristics, but removal of the lower vertical tail will result in unsatisfactory spin-recovery characteristics. The model-test results showed that a 13.3-foot wing-tip conventional parachute (drag coefficient approximately 0.7) should be effective as an emergency spin-recovery device during demonstration spins of the airplane. It was indicated that the airplane should not tumble and that no unusual longitudinal-trim characteristics should be obtained for the center-of-gravity positions investigated.

Lee, Henry A.↗
DOE OSTI2025

Ensemble cure kinetics network (ECK-Net): A method to derive cure kinetics of thermosetting resin

This paper introduces an Ensemble Cure Kinetics Network (ECK-Net), a neural network (NN)–based framework for modeling the cure kinetics of thermosetting resins within a phenomenological context. ECK-Net replaces traditional analytic models, which require extensive chemical insight and multiple isothermal/non-isothermal experiments, with a data-driven surrogate that maps nonlinear relationships between temperature, degree of cure, and reaction rate from differential scanning calorimetry data. The proposed approach predicts input-dependent kinetic coefficients of a generalized nth-order reaction equation rather than reaction rates directly, enabling a single unified model to represent various epoxy systems without relying on iso-conversional analysis or predefined functional forms. To ensure robustness, multiple independently trained networks under different random initializations are blended through an ensemble strategy, effectively mitigating the stochastic variability inherent to neural networks. The framework is validated using experimental datasets from multiple resin systems, including aerospace-grade materials (Toray 3900-2, Cycom 5320-1, and Hexcel 8552) and a windmill-grade resin (RIMR 035c). The model accurately reproduces the temporal evolution of the degree of cure under manufacturers’ recommended cure cycles across all tested resins systems, yielding Pearson’s correlation coefficients of 0.992, 0.994, 0.993, 0.997, respectively. To demonstrate process-level applicability, the trained network was implemented within the Abaqus environment to simulate out-of-autoclave (OOA) curing process of the CFRP panel composed of Toray T830H-6K/3900-2D prepreg. The simulation results showed excellent agreement with experimental temperature response (maximum peak temperature, simulation: 189.6 °C, experiment: 188.5 °C) and the final degree of cure (simulation: 0.948, experiment: 0.960 ± 0.013), confirming ECK-Net’s capability as a reliable alternative to conventional cure kinetics modeling methods.

Composite curing↗
DOE OSTI2022

2022 roadmap on 3D printing for energy

The energy transition is one of the main challenges of our society and therefore a major driver for the scientific community. To ensure a smart transition to a sustainable future energy scenario different technologies such as energy harvesting using solar cells or windmills and chemical storage in batteries, super-capacitors or hydrogen have to be developed and ultimately deployed. New fabrication approaches based on additive manufacturing and the digitalization of the industrial processes increase the potential to achieve highly efficient and smart technologies required to increase the competitiveness of clean energy technologies against fossil fuels. In this frame, the present roadmap highlights the tremendous potential of 3D printing as a new route to fully automate the manufacturing of energy devices designed as digital files. Additionally, this article gives numerous guidelines to maximize the performance and efficiency of the next generation of 3D printed devices for the energy transition while reducing the waste of critical raw materials. In particular, the paper is focused on the current status, present challenges and the expected and required advances of 3D printing for the fabrication of the most relevant energy technologies such as fuel cells and electrolysers, batteries, solar cells, super-capacitors, thermoelectric generators, chemical reactors and turbomachinery.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Three-state Potts nematic order in stacked frustrated spin models with SO(3) symmetry

Here, we propose stacked two-dimensional lattice designs of frustrated and SO(3) symmetric spin models consisting of antiferromagnetic (AF) triangular and ferromagnetic (FM) sixfold symmetric sublattices that realize emergent $\mathbb{Z}_{3}$ Potts nematic order. Considering bilinear-biquadratic spin interactions, our models describe an SO(3)-symmetric triangular lattice AF subject to a fluctuating magnetization arising from the FM coupled sublattice. We focus on the classical AFM-FM windmill model and map out the zero- and finite-temperature phase diagram using Monte Carlo simulations and analytical calculations. We discover a state with composite Potts nematic order above the ferrimagnetic three-sublattice up-up-down ground state and relate it to Potts phases in SO(3)-broken Heisenberg and Ising AFMs in external magnetic fields. Finally, we show that the biquadratic exchange in our model is automatically induced by thermal and quantum fluctuations in the purely bilinear Heisenberg model, easing the requirements for realizing these lattice designs experimentally.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Visualization of Chiral Electronic Structure and Anomalous Optical Response in a Material with Chiral Charge Density Waves

Chiral materials have attracted significant research interests as they exhibit intriguing physical properties, such as chiral optical response, spin-momentum locking, and chiral induced spin selectivity. Recently, layered transition metal dichalcogenide 1T–TaS 2 has been found to host a chiral charge density wave (CDW) order. Nevertheless, the physical consequences of the chiral order, for example, in electronic structures and the optical properties, are yet to be explored. Here, we report the spectroscopic visualization of an emergent chiral electronic band structure in the CDW phase, characterized by windmill-shaped Fermi surfaces. Further, we uncover a remarkable chirality-dependent circularly polarized Raman response due to the salient in-plane chiral symmetry of CDW, although the ordinary circular dichroism vanishes. Chiral Fermi surfaces and anomalous Raman responses coincide with the CDW transition, proving their lattice origin. Our Letter paves a path to manipulate the chiral electronic and optical properties in two-dimensional materials and explore applications in polarization optics and spintronics.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗