Search NASA⌕ Search

SEARCH · Search NASA

Results for “aerogel composite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

54 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Thermally Insulating, Thermal Shock Resistant Calcium Aluminate Phosphate Cement Composites for Reservoir Thermal Energy Storage

This paper presents the use of hydrophobic silica aerogel (HSA) and hydrophilic fly ash cenosphere (FCS) aggregates for improvements in the thermal insulating and mechanical properties of 100- and 250 °C-autoclaved calcium aluminate phosphate (CaP) cement composites reinforced with micro-glass (MGF) and micro-carbon (MCF) fibers for deployment in medium- (100 °C) and high-temperature (250 °C) reservoir thermal energy storage systems. The following six factors were assessed: (1) Hydrothermal stability of HSA; (2) Pozzolanic activity of the two aggregates and MGF in an alkali cement environment; (3) CaP cement slurry heat release during hydration and chemical reactions; (4) Composite phase compositions and phase transitions; (5) Mechanical behavior; (6) Thermal shock (TS) resistance at temperature gradients of 150 and 225 °C. The results showed that hydrophobic trimethylsilyl groups in trimethylsiloxy-linked silica aerogel structure were susceptible to hydrothermal degradation at 250 °C. This degradation was followed by pozzolanic reactions (PR) of HSA, its dissolution, and the formation of a porous microstructure that caused a major loss in the compressive strength of the composites at 250 °C. The pozzolanic activities of FCS and MGF were moderate, and they offered improved interfacial bonding at cement-FCS and cement-MGF joints through a bridging effect by PR products. Despite the PR of MGF, both MGF and MCF played an essential role in minimizing the considerable losses in compressive strength, particularly in toughness, engendered by incorporating weak HSA. As a result, a FCS/HSA ratio of 90/10 in the CaP composite system was identified as the most effective hybrid insulating aggregate composition, with a persistent compressive strength of more than 7 MPa after three TS tests at a 150 °C temperature gradient. This composite displayed thermal conductivity of 0.28 and 0.35 W/mK after TS with 225 and 150 °C thermal gradients, respectively. These values, below the TC of water (TC water = 0.6 W/mK), were measured under water-saturated conditions for applications in underground reservoirs. However, considering the hydrothermal disintegration of HSA at 250 °C, these CaP composites have potential applications for use in thermally insulating, thermal shock-resistant well cement in a mid-temperature range (100 to 175 °C) reservoir thermal energy storage system.

58 GEOSCIENCES↗
DOE OSTI2024

Base-catalyzed sol-gel inks for direct ink writing of high resolution hierarchically porous carbon aerogels

According to one aspect of an inventive concept, an ink includes a base catalyst, a sol gel precursor composition, and a block copolymer. According to another aspect of an inventive concept, an aerogel includes a three-dimensional printed structure having printed ligaments geometrically arranged, where an average diameter of the printed ligaments is in a range of greater than 0 microns and less than 50 microns. In addition, an average distance between a center of a first of the printed ligaments and a center of a second of the printed ligaments is at least equal to the average diameter of the printed ligaments, where the first and the second of the printed ligaments are adjacent. Each printed ligament includes of a plurality of random pores, where an average diameter of the random pores is less than 50 nanometers.

Zhu, Cheng↗
DOE OSTI2020

Crystalline Loading of Lipophilic Coenzyme Q10 Pharmaceuticals within Conjugated Carbon Aerogel Derivatives

Low-density aerogel materials currently are being considered for applications in controlling the rate of release for small-molecule pharmaceuticals in vivo. In particular, silica (SiO2) aerogels are an intriguing platform for controlling both the absolute amount of drug loading, but also the crystalline state of small molecule pharmaceuticals has been shown to affect drug release kinetics. To date, loading silica aerogel materials with crystalline pharmaceuticals typically require dissolving small molecules in a supercritical solvent (i.e., CO2) before drying to recover the aerogel/drug composite. Here we demonstrate a simple and low-cost method for controlling the crystallinity of the model drug coenzyme Q10 (CoQ10) within carbon aerogel materials by rationally controlling the chemical microstructure of the aerogel to exhibit ?-conjugated (sp2) chemical bonding. In particular, both pyrolyzed graphene and nanodiamond aerogels exhibit enhanced intrinsic drug loading capacity and CoQ10 crystallinity over a broad range of sp2 surface-curvature. In contrast, amorphous carbon aerogel materials are observed to load CoQ10 pharmaceuticals with strictly amorphous microstructure.

Lim, Mathew↗
DOE OSTI2020

3D Hybrid Nanofiber Aerogels Combining with Nanoparticles Made of a Biocleavable and Targeting Polycation and MiR‐26a for Bone Repair

Abstract The healing of large bone defects represents a clinical challenge, often requiring some form of grafting. 3D nanofiber aerogels could be a promising bone graft due to their biomimetic morphology and controlled porous structures and composition. miR‐26a has been reported to induce the differentiation of bone marrow‐derived mesenchymal stem cells (BMSCs) and facilitate bone formation. Introducing miR‐26a with a suitable polymeric vector targeting BMSCs could improve and enhance the functions of 3D nanofiber aerogels for bone regeneration. Herein, the comb‐shaped polycation (HA–SS–PGEA) is first developed, carrying a targeting component, biocleavable groups, and short ethanolamine (EA)‐decorated poly(glycidyl methacrylate) (PGMA) (abbreviated as PGEA) arms as miR‐26a delivery vector. Thereafter, the cytotoxicity and transfection efficiency of this polycation and cellular response to miR‐26a‐incorporated nanoparticles (NPs) are assessed in vitro. HA–SS–PGEA exhibits a stronger ability to transport miR‐26a and exert its functions than the gold standard polyethyleneimine (PEI) and low‐molecular‐weight linear PGEA. The efficacy of HA–SS–PGEA/miR‐26a NPs loaded 3D hybrid nanofiber aerogels showing a positive effect on the cranial bone defect healing is finally examined. Together, the combination of 3D nanofiber aerogels and functional NPs consisting of a biodegradable and targeting polycation and therapeutic miRNA could be a promising approach for bone regeneration.

Li, Ruiquan↗
DOE OSTI2020

Iodine Waste Form Corrosion: PNNL Summary Testing Report

A test method to correlate the laboratory corrosion behavior of iodine-containing waste forms (IWFs) to a conceptual long-term corrosion models is required. Several candidate methods have been evaluated previously, and each method presents unique challenges and limitations. Dynamic leach tests have emerged as the preferred candidate test method to evaluate IWFs and parameterize an eventual long-term corrosion model. This report was prepared in support of this effort to define the test suite to evaluate the corrosion of IWFs, with the goal of defining and parameterizing a conceptual long-term corrosion model. A review was presented highlighting the high degree of variability between the IWF corrosion data that is available in the literature and the need for a standardized test suite. The targeted test suite is composed of a single interval screening test, a dynamic leach test, and post-test solid characterization of the monolithic IWF samples. The data presented serves two purposes: to expand the range of IWFs evaluated with the test suite to assess method variability and to further understand the corrosion of IWFs to best inform conceptual long-term corrosion model development. A series of IWF types were included in the testing, including hot isostatically pressed Ag-mordenite, silver functionalized silica-based aerogels, iodosodalites (hot isostatic pressing, sintered, glass bonded ceramic), iodoapatite, tellurite glass and glass composite materials.

42 ENGINEERING↗
DOE OSTI2025

High Performance (R-10/inch) Clay-Cellulose-Silica Nanopore Insulation Board For New and Retrofit Buildings (Final Scientific Report)

The objective of Liatris’s 3-year DOE BENEFIT project was to develop and validate a high-performance, lightweight, aerogel-based insulation board of ≥R-10/inch at a cost of ≤$\$$1.50 per board foot using non-flammable inorganic nanocomposites. We have summarized each yearly goal below: Year 1 – Ambient dried inorganic/organic nanocomposite, R-6/inch Year 2 – Processing efficiency and cost down, R-8/inch at $\$$2.0/board-ft Year 3 – Scale up to continuous, pilot production of R-10 at ≤ $\$$1.50/board-ft Over the course of the project period, Liatris has successfully met or exceeded all of the goals outlined above. The project scope over 3 years was extensive, covering method development of ambient dried silica aerogels in Budget Period 1, process formulation and R-value improvement in Budget Period 2, and composite scale up with corporate partners in Budget Period 3. Over the course of the project Liatris has been able to progressively improve the thermal resistance properties from about R-6/in to > R-11/in, 2-3X the performance of conventional insulation products.

36 MATERIALS SCIENCE↗
DOE OSTI2020

System and method for forming activated carbon aerogels and performing 3D printing

Making a carbon aerogel involves 3-D printing an ink to make a printed part, removing the solvent from the printed part, and carbonizing the printed part (with the solvent removed) to make the aerogel. The ink is based on a solution of a resorcinol-formaldehyde resin (RF resin), water, and an organic thickener. Advantageously, the RF resin contains an acid catalyst, which tends to produce carbon aerogels with higher surface areas upon activation than those produced from methods involving an ink composition containing a base catalyzed resin.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Carbon-sequestration gradient insulation composites

The massive use of carbon-sequestration building materials promises a potential global carbon sink in decarbonizing the building industry. Renewable biogenic materials from abundant agriculture waste for building practice have been around over thousands of years. However, in addition to their flammability and moisture problems, addressing their low thermal and structural performance is also becoming indispensable and urgent when it comes to environmentally sustainable and energy-efficient buildings. Here, we report a nature-inspired biogenic gradient insulation composite with an optimized silica concentration of 30 wt %, a density of 0.246 g/cm 3 , and a porosity of 86%. The gradient hybrid composite exhibits a thermal conductivity of 28.2 mW m -1 K -1 , which is the lowest achieved under optimal preparation conditions. Here, it also shows a flexural modulus of 590 MPa for the aerogel-rich layer without surface modification, and it demonstrates superior fire retardancy and superhydrophobicity after surface treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Iodine Capture with Metal-Functionalized Polyacrylonitrile Composite Beads Containing Ag 0 , Bi 0 , Cu 0 , or Sn 0 Particles

The capture of radioiodine from nuclear processes and the mitigation of environmental release are important topic areas of research. Some of the more commonly employed chemisorption-type iodine scavengers reported in the literature are based on metal-exchanged porous sorbents such as Ag-zeolites or metal-functionalized aerogels and xerogels. However, another option is to use zero-valent metals directly that have known high affinities for iodine gas [i.e., I2(g)]. In this study, fine metal particles of Ag0, Bi0, Cu0, and Sn0 were embedded in porous polyacrylonitrile (PAN) substrates at 75 mass% metal loadings within the form of ellipsoidal beads with maximum diameters of ~2–3 mm. These composite beads showed extremely high iodine loadings that are directly related to the metal particle loadings. The X-ray diffraction (XRD) analyses of Ag0, Bi0, Cu0, and Sn0 particles as well as metal-PAN composite beads reacted with iodine gas at 120 ± 1 °C showed phases of AgI, BiI3, CuI, and SnI4, respectively. For the Ag-PAN, Cu-PAN, and Sn-PAN beads, no other crystalline peaks were observed in XRD for unreacted metal or oxidized metals after 48 h in saturated I2(g) at 120 ± 1 °C, whereas unreacted metallic Bi0 was observed within the Bi-PAN composites. However, after a 72 h exposure at 120 ± 1 °C, both the Bi0 particles and the Bi-PAN composites showed full conversion from Bi0 to BiI3 with XRD. Comparisons between mass uptake data and X-ray absorption spectroscopy were used to better understand the phase distribution of the Bi phases present in the Bi-PAN+I composites. The iodine loadings (mg iodine per g sorbent, or qe) for these materials were 1120 (Ag-Particle), 1382 (Bi-Particle-72h), 1033 (Cu-Particle), 3000 (Sn-Particle), 753 (Ag-PAN), 1012 (Bi-PAN-72h), 1457 (Cu-PAN), and 1669 (Sn-PAN). It is possible that inexpensive sorbents such as these could be deployed to help limit or prevent release of radioiodine to the environment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Insulation Activation and Contamination in Low-Power Experiments

Among the diverse advanced nuclear reactor concepts being developed are designs that expect to operate at much higher temperatures than conventional light-water reactors, and therefore require alternative materials for components capable of withstanding these extreme temperatures. Insulation is one such component where alternative high-temperature industrial composites are being considered. Low-power experiments can provide an opportunity for advancing our understanding of material behavior under irradiation; however, these experiments are not without occupational hazards. The focus of this paper is the potential for activation of insulating composites when exposed to neutron fluence during reactor experiments, and to discuss the subsequent contamination of the testing area. This paper will also discuss practical measures for preventing the creation and inhalation of activated particulate matter (i.e., dust), such as engineering and administrative controls and personal protective equipment. This paper evaluates the suitability of several insulation materials for use in reactor experiments based on their activation from neutron irradiation. The materials considered are Pyrogel XTE by Aspen Aerogel, Cerablanket and Kaowool by Morgan Advanced Materials, Thermo-12 Gold by Johns Manville, and Maxsil CF6-2000 by McAllister Mills. Although these materials are not yet widely used in the nuclear industry, they are common in other industries due to their thermal insulating properties. These materials produce dust while handling that can pose health and safety hazards, which could be further exacerbated by activation. The analysis presented in this paper utilizes a deterministic method developed to predict the activation source term of the provided insulation materials. The method calculates the atomic density of each element within the composites and simulates their exposure to a specified neutron flux density representative of low power experimental conditions. During the irradiation phase and throughout the extensive cooling period, neutron absorptions and nuclear decays are tracked for relevant isotopes. The residual activity within each composite is then assessed to identify the material with the lowest potential radiological hazard to workers. Dust will be created during installation and removal of insulating materials and may also be generated during the experiment. Contamination of surrounding surfaces due to dispersion is highly likely unless preventative measures are taken. The results of this analysis are used to estimate an internal dose from inhalation of activated dust, which is significantly lower than the allowable whole-body dose. However, the risk of internal exposure may increase if the dust becomes a transport vector for nuclear material. The goals of this paper are to enhance the understanding of the potential activation and contamination hazards from the use of these insulating materials in low-power nuclear experiments and to foster safer work environments through informed decision-making and strategic planning. This work ultimately contributes to a broader understanding of how new non-nuclear materials for advanced reactors impact the radiological safety of co-located workers, helping to ensure the responsible management of radioactive materials during installation and decommissioning activities.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗
DOE OSTI2022

High temperature ceramic thermal insulation material

Flexible and lightweight thermal insulation materials with hierarchical microstructures are ubiquitous in thermal management and protection systems. Ceramic aerogels promise high-temperature thermal insulation but lack mechanical robustness, while the fibrous materials with excellent mechanical elasticity display modest thermal insulation. Here we describe flexible hierarchical superhydrophobic ceramic insulation nanocomposites through the densified architectured hierarchical nanostructures, radiative insulation coating, and interfacial cross-linking among composites. The lightweight flexible ceramic nanocomposites exhibit a density of 0.13 g/cm 3 , high-temperature fire resistance with thermal conductivity of 0.024 W/(m·K), and super-hydrophobicity with the water contact angle of 152°. The mechanical robustness and high-temperature thermal insulation of ceramic nanocomposites, together with its soundproof performance, shed light on the low-cost flexible insulation materials manufacturing with scalability for high-temperature thermal insulation applications under high mechanical loading conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Melting of Magnesium Borohydride under High Hydrogen Pressure: Thermodynamic Stability and Effects of Nanoconfinement

The thermodynamic stability and melting point of magnesium borohydride were probed under hydrogen pressures up to 1000 bar (100 MPa) and temperatures up to 400 °C. At 400 °C, Mg(BH4)2 was found to be chemically stable between 700 and 1000 bar H2, whereas under 350 bar H2 or lower pressures, the bulk material partially decomposed into MgH2 and MgB12H12. The melting point of solvent-free Mg(BH4)2 was estimated to be 367-375 °C, which was above previously reported values by 40-90 °C. Our results indicated that a high hydrogen backpressure is needed to prevent the decomposition of Mg(BH4)2 before measuring the melting point and that molten Mg(BH4)2 can exist as a stable liquid phase between 367 and 400 °C under hydrogen overpressures of 700 bar or above. The occurrence of a pure molten Mg(BH4)2 phase enabled efficient melt-infiltration of Mg(BH4)2 into the pores of porous templated carbons (CMK-3 and CMK-8) and graphene aerogels. Both transmission electron microscopy and small-angle X-ray scattering confirmed efficient incorporation of the borohydride into the carbon pores. The Mg(BH4)2@carbon samples exhibited comparable hydrogen capacities to bulk Mg(BH4)2 upon desorption up to 390 °C based on the mass of the active component; the onset of hydrogen release was reduced by 15-25 °C compared to the bulk. Importantly, melt-infiltration under hydrogen pressure was shown to be an efficient way to introduce metal borohydrides into the pores of carbon-based materials, helping to prevent particle agglomeration and formation of stable closo-polyborate byproducts.

White, James L.↗
DOE OSTI2024

Copper and bismuth-based sorbent characterization in simulated iodine off-gas streams

The effective capture of volatile radioiodine, a fission product present in used nuclear fuel (UNF), is of paramount importance for development of used fuel reprocessing schemes to prevent release of radioiodine during unit operations and to meet regulatory standards for air emissions. A well-studied method for iodine capture in off-gas streams is the use of silver-functionalized zeolite phases (AgZ), which exploit chemisorption of I to Ag. Advances into other Ag-functionalized materials, including aerogels and metal organic frameworks (MOFs), are underway [1]. Additional metals with the capability to chemisorb iodine, including Cu, Bi, and Sn, [1] are being evaluated as alternatives to Ag for potential applicability to iodine management in off-gas systems. The design of novel functionalized sorbents with Cu and Bi, including composites with metal particles embedded in PAN substrates [2] and composites with metal sulfides embedded in PAN [3], is an ongoing area of study for improved iodine capture. Previously reported work on novel PAN-based metal sorbents has provided the synthesis, characterization, and iodine capture efficiency of this new class of sorbent. Specifically, the metal sulfide PAN composites are found to be easy to produce and reproduce, as well as having a high iodine loading potential under static conditions [3]. Due to the favorable testing previously performed with metal sulfide PAN composites, further testing into the performance of these composites under gas streams containing I2(g) in combination with NO2(g) and H2O(g) is needed. Humid streams of NO2(g) may arise from dissolver off-gas streams, when used fuel is dissolved in HNO3(aq) [4]. NO2(g) has been found to reduce AgZ sorption capacity for I because of oxidation of Ag, the chemisorbing agent, to Ag2O [5]. It follows that performance evaluation of novel sorbents under highly oxidizing conditions such as NO2(g) streams is critical. Therefore, the objective of this study is to determine the effect of flowing NO2(g) and H2O(g) streams on iodine sorption capacity and sorbent performance. This work utilizes custom-built gas handling capabilities for sorbent exposure along with solid-state characterization techniques to assess the physical and chemical properties of sorbents before and after exposure.

copper, bismuth, iodine capture, iodine sorbent, p↗
DOE OSTI2021

3D Printed Nickel–Molybdenum-Based Electrocatalysts for Hydrogen Evolution at Low Overpotentials in a Flow-Through Configuration

Three-dimensional (3D) printed, hierarchically porous nickel molybdenum (NiMo) electrocatalysts were synthesized and evaluated in a flow-through configuration for the hydrogen evolution reaction (HER) in 1.0 M KOH(aq) in a simple electrochemical H-cell. 3D NiMo electrodes possess hierarchically porous structures because of the resol-based aerogel precursor, which generates superporous carbon aerogel as a catalyst support. Relative to a traditional planar electrode configuration, the flow-through configuration allowed efficient removal of the hydrogen bubbles from the catalyst surface, especially at high operating current densities, and significantly decreased the overpotentials required for HER. An analytical model that accounted for the electrokinetics of HER as well as the mass transport with or without the flow-through configuration was developed to quantitatively evaluate voltage losses associated with kinetic overpotentials and ohmic resistance due to bubble formation in the porous electrodes. Furthermore, the chemical composition, electrochemical surface area (ECSA), and roughness factor (RF) were also systematically studied to assess the electrocatalytic performance of the 3D printed, hierarchically porous NiMo electrodes. An ECSA of 25163 cm2 was obtained with the highly porous structures, and an average overpotential of 45 mV at 10 mA cm–2 was achieved over 24 h by using the flow-through configuration. The flow-through configuration evaluated in the simple H-cell achieved high electrochemical accessible surface areas for electrochemical reactions and provided useful information for adaption of the porous electrodes in flow cells.

08 HYDROGEN↗
DOE OSTI2022

Approaching air buoyancy in aero/cryogel vacuum vessels

Air impermeability has been observed in low-density aerogel and cryogel materials, which has led to a series of experiments to investigate the feasibility of an air buoyant vacuum vessel, as well as the fabrication and testing of sub-buoyant prototypes. Here, bulk samples of silica aerogel were shown to isolate vacuum from ambient air for several hours with optimal vacuum isolation occurring at a density of approximately 85 mg cm –3 . It was demonstrated using polyimide aerogel and cryogel materials that the ability of these foam materials to provide an air impermeable layer between vacuum and atmosphere, in spite of being comprised of mostly void space, is related to material stiffness. It is hypothesized that this behavior is due to local deformation of the random nanostructure of the material. Spherical shell vacuum vessels were produced using the polyimide cryogel, and less than 133 Pa vacuum containment was demonstrated under active pumping. In order to approach the non-buoyant to buoyant transition for these vacuum vessels, a polyimide composite was produced using helical fibers for which preliminary mechanical testing was performed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Fe-single-atom catalyst nanocages linked by bacterial cellulose-derived carbon nanofiber aerogel for Li-S batteries

Li-S battery (LSB) is promising for achieving high capacity. Still, its development is hindered by the complex redox process with sluggish kinetics and particularly the resulting lithium polysulfides (LiPS) shuttle effects. Single-atom catalysts (SACs), with their maximized atom utilization, could effectively chemisorb soluble LiPSs and expedite the sulfide conversion reaction kinetics. Here we report incorporating Fe single metal atom catalyst (Fe-SAC) in the sulfur cathode design and its electrocatalytic effects. Fe-doped ZIF-8 nanocages were introduced into a cheap biomass bacteria cellulose. A pyrolysis process converted them into an aerogel structure with Fe-SAC-functionalized N-doped carbon nanocages linked by a carbon nanofiber network (FeSA-NC@CBC), which was applied as a scaffold to fabricate freestanding and binder-free sulfur cathodes. He we conducted electrochemical measurements to reveal Fe-SAC functions including lowering energy barriers for S 8 reduction to liquid-phase LiPSs and further to solid-phase Li 2 S 2 /Li 2 S and accelerating Li 2 S 2 /Li 2 S nucleation and deposition, as corroborated by our theoretical calculation results. Benefiting from the synergistic effects of highly active Fe-SAC and three-dimensional conductive network, the sulfide reaction kinetics is improved, which can diminish LiPS shuttle effects and therefore improve LBS rate performance and cycling stability. Accordingly, the fabricated FeSA-NC@CBC composite cathode delivers an excellent rate capability at 2C with a reversible capacity of 840 mAh/g and a long-term cyclic stability of 800 mAh/g at 1C after 500 cycles.

25 ENERGY STORAGE↗
DOE OSTI2022

Creation of hollow silica-fiberglass soft ceramics for thermal insulation

Hollow-structured materials show promise in thermal insulation because the shells encapsulating gaseous voids can interrupt heat transport pathways. Here, in this study, we present two low-cost routes to fabricate hollow silica nanoshells, via gas-phase and liquid-phase methods. The gas-phase synthesis method generates hollow shells by a droplet surface precipitation mechanism in a flame aerosol reactor. The liquid-phase synthesis route forms hollow shells by removal of a carbon template, which is produced by hydrothermal reaction of glucose. Both approaches (gas- and liquid-phase) provide hollow silica with amorphous structure, low thermal conductivity (0.023 and 0.026 W m –1 K –1 ), small particle size (442 and 383 nm), thin shell (35 and 36 nm), and low density (0.015 and 0.033 g cm –3 ). We employed high shear mechanical mixing to fabricate hollow silica-fiberglass composite ceramics. The resulting three-dimensional network provides the ceramics with robust mechanical elasticity and fire-retardancy while maintaining low thermal conductivity, dramatically outperforming an analogous material using commercial silica gel in place of the hollow nanoshells. Our findings provide two practical routes to synthesize hollow silica, either of which can be used to manufacture a class of hollow shell-fiber nanocomposite soft ceramics for energy-saving applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Amorphous K–Co–Mo–S x Chalcogel: A Synergy of Surface Sorption and Ion-Exchange

Chalcogel represents a unique class of meso- to macroporous nanomaterials that offer applications in energy and environmental pursuits. We report the synthesis of an ion-exchangeable amorphous chalcogel using a nominal composition of K 2 CoMo 2 S 10 (KCMS) at room temperature is reported. Synchrotron X-ray pair distribution function (PDF), X-ray absorption near-edge structure (XANES), and extended X-ray absorption fine structure (EXAFS) reveal a plausible local structure of KCMS gel consisting of Mo 5+ 2 and Mo 4+ 3 clusters in the vicinity of di/polysulfides which are covalently linked by Co 2+ ions. The ionically bound K + ions remain in the percolating pores of the Co–Mo–S covalent network. XANES of Co K-edge shows multiple electronic transitions, including quadrupole (1s→3d), shakedown (1s→4p + MLCT), and dipole allowed 1s→4p transitions. Remarkably, despite a lack of regular channels as in some crystalline solids, the amorphous KCMS gel shows ion-exchange properties with UO 2 2+ ions. Additionally, it also presents surface sorption via [S∙∙∙∙UO 2 2+ ] covalent interactions. Overall, this study underscores the synthesis of quaternary chalcogels incorporating alkali metals and their potential to advance separation science for cations and oxo-cationic species by integrating a synergy of surface sorption and ion-exchange.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗