Search NASA⌕ Search

SEARCH · Search NASA

Results for “antenna arraying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Theory of a Traveling Wave Feed for a Planar Slot Array Antenna

Planar arrays of waveguide-fed slots have been employed in many radar and remote sensing applications. Such arrays are designed in the standing wave configuration because of high efficiency. Traveling wave arrays can produce greater bandwidth at the expense of efficiency due to power loss in the load or loads. Traveling wave planar slot arrays may be designed with a long feed waveguide consisting of centered-inclined coupling slots. The feed waveguide is terminated in a matched load, and the element spacing in the feed waveguide is chosen to produce a beam squinted from the broadside. The traveling wave planar slot array consists of a long feed waveguide containing resonant-centered inclined coupling slots in the broad wall, coupling power into an array of stacked radiating waveguides orthogonal to it. The radiating waveguides consist of longitudinal offset radiating slots in a standing wave configuration. For the traveling wave feed of a planar slot array, one has to design the tilt angle and length of each coupling slot such that the amplitude and phase of excitation of each radiating waveguide are close to the desired values. The coupling slot spacing is chosen for an appropriate beam squint. Scattering matrix parameters of resonant coupling slots are used in the design process to produce appropriate excitations of radiating waveguides with constraints placed only on amplitudes. Since the radiating slots in each radiating waveguide are designed to produce a certain total admittance, the scattering (S) matrix of each coupling slot is reduced to a 2x2 matrix. Elements of each 2x2 S-matrix and the amount of coupling into the corresponding radiating waveguide are expressed in terms of the element S11. S matrices are converted into transmission (T) matrices, and the T matrices are multiplied to cascade the coupling slots and waveguide sections, starting from the load end and proceeding towards the source. While the use of non-resonant coupling slots may provide an additional degree of freedom in the design, resonant coupling slots simplify the design process. The amplitude of the wave going to the load is set at unity. The S11 parameter, r of the coupling slot closest to the load, is assigned an arbitrary value. A larger value of r will reduce the power dissipated in the load while increasing the reflection coefficient at the input port. It is now possible to obtain the excitation of the radiating waveguide closest to the load and the coefficients of the wave incident and reflected at the input port of this coupling slot. The next coupling slot parameter, r , is chosen to realize the excitation of that radiating waveguide. One continues this process moving towards the source, until all the coupling slot parameters r and hence the S11 parameter of the 4-port coupler, r, are known for each coupling slot. The goal is to produce the desired array aperture distribution in the feed direction. From an interpolation of the computed moment method data for the slot parameters, all the coupling slot tilt angles and lengths are obtained. From the excitations of the radiating waveguides computed from the coupling values, radiating slot parameters may be obtained so as to attain the desired total normalized slot admittances. This process yields the radiating slot parameters, offsets, and lengths. The design is repeated by choosing different values of r for the last coupling slot until the percentage of power dissipated in the load and the input reflection coefficient values are satisfactory. Numerical results computed for the radiation pattern, the tilt angles and lengths of coupling slots, and excitation phases of the radiating waveguides, are presented for an array with uniform amplitude excitation. The design process has been validated using computer simulations. This design procedure is valid for non-uniform amplitude excitations as well.

Rengarajan, Sembiam↗

Evolutionary Design of a Phased Array Antenna Element

We present an evolved S-band phased array antenna element design that meets the requirements of NASA's TDRS-C communications satellite scheduled for launch early next decade. The original specification called for two types of elements, one for receive only and one for transmit/receive. We were able to evolve a single element design that meets both specifications thereby simplifying the antenna and reducing testing and integration costs. The highest performance antenna found using a genetic algorithm and stochastic hill-climbing has been fabricated and tested. Laboratory results are largely consistent with simulation. Researchers have been investigating evolutionary antenna design and optimization since the early 1990s, and the field has grown in recent years its computer speed has increased and electromagnetic simulators have improved. Many antenna types have been investigated, including wire antennas, antenna arrays and quadrifilar helical antennas. In particular, our laboratory evolved a wire antenna design for NASA's Space Technology 5 (ST5) spacecraft. This antenna has been fabricated, tested, and is scheduled for launch on the three spacecraft in 2006.

Globus, Al↗

The design of a microstrip antenna array for a UHF space telemetry link

An array of microstrip antenna panels was designed for use on a small instrumented satellite as part of a 400-MHz telemetry link between that satellite and NASA's shuttle spacecraft. A roughly omnidirectional phi-plane pattern was desired. The 1.4-wavelength diameter of the satellite and the various ports and structures on its surface presented strong constraints on the antenna array design. Eight antennas, each one a quarter-wavelength panel with one radiating and one shorted edge, were chosen. A phi-plane pattern ripple of 4.4 dB and a gain of at least 0.1 dB relative to a half-wavelength dipole were realized. The design technique used for the individual antenna panels included the study of feed-point location for impedance matching and the effect of losses in the dielectric. A superposition method was used to synthesize the radiation patterns for different numbers and different excitations of antennas on the satellite.

Post, R. E.↗

Modeling the Atmospheric Phase Effects of a Digital Antenna Array Communications System

In an antenna array system such as that used in the Deep Space Network (DSN) for satellite communication, it is often necessary to account for the effects due to the atmosphere. Typically, the atmosphere induces amplitude and phase fluctuations on the transmitted downlink signal that invalidate the assumed stationarity of the signal model. The degree to which these perturbations affect the stationarity of the model depends both on parameters of the atmosphere, including wind speed and turbulence strength, and on parameters of the communication system, such as the sampling rate used. In this article, we focus on modeling the atmospheric phase fluctuations in a digital antenna array communications system. Based on a continuous-time statistical model for the atmospheric phase effects, we show how to obtain a related discrete-time model based on sampling the continuous-time process. The effects of the nonstationarity of the resulting signal model are investigated using the sample matrix inversion (SMI) algorithm for minimum mean-squared error (MMSE) equalization of the received signal

Tkacenko, A.↗

Antenna and Flight Control Software for Conformal Phased Array Antenna Design (CPAAD)

The National Aeronautics and Space Administration (NASA) is developing lightweight conformal phased array antenna designs (CPAAD) for beyond line of sight communications [1]. The CPAAD system is developed to address reliable and affordable autonomous next generation aviation systems. The technology takes advantage of newly assigned provisional Ku-bands for UAVs. The antenna design is unique to avoid interference with the ground and the unconventional substrate reduces weight. The surface mounted conformal design allows for reduced drag during flight. The software developed for the CPAAD system operates the antenna hardware and provides a graphic user interface (GUI) for ground testing and flight operations.

phased array antenna control software↗

Frequency translating phase conjugation circuit for active retrodirective antenna array

An active retrodirective antenna array which has central phasing from a reference antenna element through a "tree" structured network of transmission lines utilizes a number of phase conjugate circuits (PCCs) at each node and a phase reference regeneration circuit (PRR) at each node except the initial node. Each node virtually coincides with an element of the array. A PCC generates the exact conjugate phase of an incident signal using a phase locked loop which combines the phases in an up converter, divides the sum by 2 and mixes the result with the phase in a down converter for phase detection. The PRR extracts the phase from the conjugate phase. Both the PCC and the PRR are not only exact but also free from mixer degeneracy.

Chernoff, R.↗

A Study of Cross Polarization Effects in Reflector Antenna Arrays

This paper addresses the issue of cross-polarized field components of an array of antennas as compared to that of individual elements of the array. For a single antenna, the co- and cross-polarization components are completely correlated in terms of phase and amplitude in a given direction. The co/cross-pol relations vary as a function of angular position from peak of the beam, which is important when there is pointing error. More specifically, for the reflector antennas, this relation might vary as the antenna points in different directions in azimuth and elevation, due to the changes in gravity profile, wind effects, temperature changes, etc., on the surface and feed/sub/main reflector alignment. In an array environment, these changes will vary among various antennas in the array, and indeed very small mechanical and design variations in the antenna elements (in terms of feed horns, feed/reflector misalignments, surface variations, etc., will contribute to the cross polarization variations.

cross polarization↗

Continuous Spacecraft Communications via Make-Before-Break Antenna Array Beam Steering

Active phased array (APA) antennas can electronically form multiple beams to track several targets simultaneously. Spacecraft equipped with these antennas can achieve continuous communications through a constellation of relay satellites by forming a second beam to an upcoming relay satellite before the spacecraft moves beyond the current relay’s line of sight. These make-before-break operations have utility for streaming critical data without gaps. Using characterization data from a commercially-available APA-based satellite communications terminal, we simulate performance from low-Earth orbit to a representative geosynchronous relay satellite system at Ka-band. Average data rates of 3 Mbps are achievable with a minimum rate of 0.8 Mbps during worst-case handovers. We prototype the beam-splitting algorithm in the terminal hardware and evaluate its performance in an antenna range. In an over-the-air test emulating a handover between two relays we observe error-free data in the combined telemetry stream.

active phased array antennas↗

Distributed Architecture For Phased-Array Antennas

Distributed Architecture for Phased Array Antennas (DISTAR) computer program simulation tool used to study implementation of distributed phased-array equipment. Allows placement of possibly-faulty transmitting/receiving modules at locations throughout array. Variations in amplifiers and phase shifters degrades performance of antenna, depending on environmental conditions and array architecture. Enables antenna designer to examine characteristics of array and how they affect both types and extents of antenna failures. General specifications for amplifier and phase-shifter tolerances determined for various architectures. Written in FORTRAN 77.

Davidson, Shayla E.↗

Antenna array with low Rx and Tx sidelobe levels

The various technologies presented herein relate to mitigating or reducing sidelobe levels during operation of an antenna array. Power coefficients operating across an antenna array are tapered to facilitate a power concentration at central region of the antenna array while power coefficients of a lower magnitude are generated at the periphery of the antenna array. Power coefficient variation can be effected by at least one of electrical path length, number of antennas being powered in a particular antenna subarray, a number of T-splitters incorporated into an electrical path servicing an antenna, etc. Electrical coupling of a pre-T/R stripline and a post-T/R stripline can be achieved in conjunction with operation with a dielectric layer, wherein the dielectric layer acts as a dielectric at the K.sub.u frequency band. Further, phase delay can be applied to at least one electrical signal to facilitate concurrent delivery of power across the antenna array.

42 ENGINEERING↗

Phase conjugation method and apparatus for an active retrodirective antenna array

An active retrodirective antenna array wherein a reference array element is used to generate a phase reference which is replicated at succeeding elements of the array. Each element of the array is associated with a phase regeneration circuit and the phase conjugation circuitry of an adjacent element. In one implementation, the phase reference circuit operates on the input signal at the reference element, a voltage controlled oscillator (VCO) output signal and the input pilot signal at the next array element received from a transmission line. By proper filtering and mixing, a phase component may be produced to which the VCO may be locked to produce the phase conjugate of the pilot signal at the next array element plus a transmission line delay. In another implementation, particularly suited for large arrays in space, two different input pilot frequencies are employed.

Tausworthe, R. C.↗

Phased Array Antenna Testbed Development at the NASA Glenn Research Center

Ideal phased array antennas offer advantages for communication systems, such as wide-angle scanning and multibeam operation, which can be utilized in certain NASA applications. However, physically realizable, electronically steered, phased array antennas introduce additional system performance parameters, which must be included in the evaluation of the system. The NASA Glenn Research Center (GRC) is currently conducting research to identify these parameters and to develop the tools necessary to measure them. One of these tools is a testbed where phased array antennas may be operated in an environment that simulates their use. This paper describes the development of the testbed and its use in characterizing a particular K-Band, phased array antenna.

Lambert, Kevin M.↗

A finite element-boundary integral method for conformal antenna arrays on a circular cylinder

Conformal antenna arrays offer many cost and weight advantages over conventional antenna systems. In the past, antenna designers have had to resort to expensive measurements in order to develop a conformal array design. This was due to the lack of rigorous mathematical models for conformal antenna arrays. As a result, the design of conformal arrays was primarily based on planar antenna design concepts. Recently, we have found the finite element-boundary integral method to be very successful in modeling large planar arrays of arbitrary composition in a metallic plane. We are extending this formulation to conformal arrays on large metallic cylinders. In doing so, we will develop a mathematical formulation. In particular, we discuss the finite element equations, the shape elements, and the boundary integral evaluation. It is shown how this formulation can be applied with minimal computation and memory requirements.

Kempel, Leo C.↗

A finite element-boundary integral method for conformal antenna arrays on a circular cylinder

Conformal antenna arrays offer many cost and weight advantages over conventional antenna systems. In the past, antenna designers have had to resort to expensive measurements in order to develop a conformal array design. This is due to the lack of rigorous mathematical models for conformal antenna arrays, and as a result the design of conformal arrays is primarily based on planar antenna design concepts. Recently, we have found the finite element-boundary integral method to be very successful in modeling large planar arrays of arbitrary composition in a metallic plane. Herewith we shall extend this formulation for conformal arrays on large metallic cylinders. In this we develop the mathematical formulation. In particular we discuss the finite element equations, the shape elements, and the boundary integral evaluation, and it is shown how this formulation can be applied with minimal computation and memory requirements. The implementation shall be discussed in a later report.

Kempel, Leo C.↗

Low-Cost Phased Array Antenna for Sounding Rockets, Missiles, and Expendable Launch Vehicles

A low-cost beamformer phased array antenna has been developed for expendable launch vehicles, rockets, and missiles. It utilizes a conformal array antenna of ring or individual radiators (design varies depending on application) that is designed to be fed by the recently developed hybrid electrical/mechanical (vendor-supplied) phased array beamformer. The combination of these new array antennas and the hybrid beamformer results in a conformal phased array antenna that has significantly higher gain than traditional omni antennas, and costs an order of magnitude or more less than traditional phased array designs. Existing omnidirectional antennas for sounding rockets, missiles, and expendable launch vehicles (ELVs) do not have sufficient gain to support the required communication data rates via the space network. Missiles and smaller ELVs are often stabilized in flight by a fast (i.e. 4 Hz) roll rate. This fast roll rate, combined with vehicle attitude changes, greatly increases the complexity of the high-gain antenna beam-tracking problem. Phased arrays for larger ELVs with roll control are prohibitively expensive. Prior techniques involved a traditional fully electronic phased array solution, combined with highly complex and very fast inertial measurement unit phased array beamformers. The functional operation of this phased array is substantially different from traditional phased arrays in that it uses a hybrid electrical/mechanical beamformer that creates the relative time delays for steering the antenna beam via a small physical movement of variable delay lines. This movement is controlled via an innovative antenna control unit that accesses an internal measurement unit for vehicle attitude information, computes a beam-pointing angle to the target, then points the beam via a stepper motor controller. The stepper motor on the beamformer controls the beamformer variable delay lines that apply the appropriate time delays to the individual array elements to properly steer the beam. The array of phased ring radiators is unique in that it provides improved gain for a small rocket or missile that uses spin stabilization for stability. The antenna pattern created is symmetric about the roll axis (like an omnidirectional wraparound), and is thus capable of providing continuous coverage that is compatible with very fast spinning rockets. For larger ELVs with roll control, a linear array of elements can be used for the 1D scanned beamformer and phased array, or a 2D scanned beamformer can be used with an NxN element array.

Mullinix, Daniel↗

Phased-Antenna-Array Conical Scanning

Antenna pointing faster than mechanical scanning. Three antenna phased array connected to receiving signal-processing system through two phase-shifting networks. Two networks simultaneously steer phased array in two slightly-different beam directions; one for scanning, one for tracking. Technique has many uses in military and civilian radar, principally in tracking aircraft, balloonborne weather instruments, and other moving signal sources or reflectors.

Lesh, J. R.↗

Resonance spectra of diabolo optical antenna arrays

A complete set of diabolo optical antenna arrays with different waist widths and periods was fabricated on a sapphire substrate by using a standard e-beam lithography and lift-off process. Fabricated diabolo optical antenna arrays were characterized by measuring the transmittance and reflectance with a microscope-coupled FTIR spectrometer. It was found experimentally that reducing the waist width significantly shifts the resonance to longer wavelength and narrowing the waist of the antennas is more effective than increasing the period of the array for tuning the resonance wavelength. Also it is found that the magnetic field enhancement near the antenna waist is correlated to the shift of the resonance wavelength.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗