Search NASA⌕ Search

SEARCH · Search NASA

Results for “axial”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Evaluation of axial lock-up of space shuttle main engine bearings from high pressure oxygen turbopump

The mainshaft support bearings of long life turbopumps for use on the space shuttle were evaluated to determine possible causes of failure. Specific aspects examined include the sensitivity of 15 degree versus 25 degree contact angle bearings with regard to heat damage and thermal runaway, the L/D aspects of the turbine end bearing pair with regard to hang-up due to cocking, the hang-up required to support a 44.5 KN axial load without cartridge slipping, the outer race growth as a result of a 44.5 KN axial load, and bearing torque as a function of axial load. Results indicate that hang-up of the cartridge due to bearing heating is a serious problem especially if poor lubrication of the bearing occurs and that race growth due to axial load can contribute to cartridge lock-up. The experimental evaluation of bearing performance under axial loads indicates that the bearing torque is a strong function of surface lubrication.

Kannel, J. W.↗
NASA NTRS1999

Eigenmodes of Ducted Flows With Radially-Dependent Axial and Swirl Velocity Components

This report characterizes the sets of small disturbances possible in cylindrical and annular ducts with mean flow whose axial and tangential components vary arbitrarily with radius. The linearized equations of motion are presented and discussed, and then exponential forms for the axial, circumferential, and time dependencies of any unsteady disturbances are assumed. The resultant equations form a generalized eigenvalue problem, the solution of which yields the axial wavenumbers and radial mode shapes of the unsteady disturbances. Two numerical discretizations are applied to the system of equations: (1) a spectral collocation technique based on Chebyshev polynomial expansions on the Gauss-Lobatto points, and (2) second and fourth order finite differences on uniform grids. The discretized equations are solved using a standard eigensystem package employing the QR algorithm. The eigenvalues fall into two primary categories: a discrete set (analogous to the acoustic modes found in uniform mean flows) and a continuous band (analogous to convected disturbances in uniform mean flows) where the phase velocities of the disturbances correspond to the local mean flow velocities. Sample mode shapes and eigensystem distributions are presented for both sheared axial and swirling flows. The physics of swirling flows is examined with reference to hydrodynamic stability and completeness of the eigensystem expansions. The effect of assuming exponential dependence in the axial direction is discussed.

Kousen, Kenneth A.↗
NASA NTRS2001

Reduced Toxicity Fuel Satellite Propulsion System Including Axial Thruster and ACS Thruster Combination

A reduced toxicity fuel satellite propulsion system including a reduced toxicity propellant supply for consumption in an axial class thruster and an ACS class thruster. The system includes suitable valves and conduits for supplying the reduced toxicity propellant to the ACS decomposing element of an ACS thruster. The ACS decomposing element is operative to decompose the reduced toxicity propellant into hot propulsive gases. In addition the system includes suitable valves and conduits for supplying the reduced toxicity propellant to an axial decomposing element of the axial thruster. The axial decomposing element is operative to decompose the reduced toxicity propellant into hot gases. The system further includes suitable valves and conduits for supplying a second propellant to a combustion chamber of the axial thruster, whereby the hot gases and the second propellant auto-ignite and begin the combustion process for producing thrust.

Steven J Schneider↗
NASA NTRS2000

Prebuckling and Postbuckling Response of Tailored Composite Stiffened Panels with Axial-Shear Coupling

Results of a numerical parametric study of the prebuckling and postbuckling response of tailored composite stiffened panels with axial-shear coupling are presented. In the stiffened panels, axial-shear stiffness coupling is created by rotating the stiffener orientation and tailoring the skin laminate anisotropy. The panels are loaded in axial compression and the effects of stiffener orientation and skin anisotropy on the panel stiffness, buckling parameters, and axial-shear coupling response are described. Results are obtained from a nonlinear general shell finite element analysis computer code. The prebuckling and postbuckling responses can be affected by both the stiffener orientation and skin laminate anisotropy, and the effects are different and load dependent. The results help identify different mechanisms for axial-shear coupling, and show that a load-dependent structural response can be controlled by selecting appropriate stiffener and skin parameters.

Young, Richard D.↗
NASA NTRS2001

Lumbar spine disc height and curvature responses to an axial load generated by a compression device compatible with magnetic resonance imaging

STUDY DESIGN: Axial load-dependent changes in the lumbar spine of supine healthy volunteers were examined using a compression device compatible with magnetic resonance imaging. OBJECTIVE: To test two hypotheses: Axial loading of 50% body weight from shoulder to feet in supine posture 1) simulates the upright lumbar spine alignment and 2) decreases disc height significantly. SUMMARY OF BACKGROUND DATA: Axial compression on the lumbar spine has significantly narrowed the lumbar dural sac in patients with sciatica, neurogenic claudication or both. METHODS: Using a device compatible with magnetic resonance imaging, the lumbar spine of eight young volunteers, ages 22 to 36 years, was axially compressed with a force equivalent to 50% of body weight, approximating the normal load on the lumbar spine in upright posture. Sagittal lumbar magnetic resonance imaging was performed to measure intervertebral angle and disc height before and during compression. RESULTS: Each intervertebral angle before and during compression was as follows: T12-L1 (-0.8 degrees +/- 2.5 degrees and -1.5 degrees +/- 2.6 degrees ), L1-L2 (0.7 degrees +/- 1.4 degrees and 3.3 degrees +/- 2.9 degrees ), L2-L3 (4.7 degrees +/- 3.5 degrees and 7.3 degrees +/- 6 degrees ), L3-L4 (7.9 degrees +/- 2.4 degrees and 11.1 degrees +/- 4.6 degrees ), L4-L5 (14.3 degrees +/- 3.3 degrees and 14.9 degrees +/- 1.7 degrees ), L5-S1 (25.8 degrees +/- 5.2 degrees and 20.8 degrees +/- 6 degrees ), and L1-S1 (53.4 degrees +/- 11.9 degrees and 57.3 degrees +/- 16.7 degrees ). Negative values reflect kyphosis, and positive values reflect lordosis. A significant difference between values before and during compression was obtained at L3-L4 and L5-S1. There was a significant decrease in disc height only at L4-L5 during compression. CONCLUSIONS: The axial force of 50% body weight in supine posture simulates the upright lumbar spine morphologically. No change in intervertebral angle occurred at L4-L5. However, disc height at L4-L5 decreased significantly during compression.

Non-NASA Center↗
NASA NTRS1948

Effect of Turbine Axial Nozzle-Wheel Clearance on Performance of Mark 25 Torpedo Power Plant

Investigations were made of the turbine from a Mark 25 torpedo to determine the performance of the unit with three different turbine nozzles at various axial nozzle-wheel clearances. Turbine efficiency with a reamed nondivergent nozzle that uses the axial clearance space for gas expansion was little affected by increasing the axial running clearance from 0.030 to 0.150 inch. Turbine efficiency with cast nozzles that expanded the gas inside the nozzle passage was found to be sensitive to increased axial nozzle-wheel clearance. A cast nozzle giving a turbine brake efficiency of 0.525 at an axial running clearance of 0.035 inch gave a brake efficiency of 0.475 when the clearance was increased to 0.095 inch for the same inlet-gas conditions and blade-jet speed ratio. If the basis for computing the isentropic power available to the turbine is the temperature inside the nozzle rather then the temperature in the inlet-gas pipe, an increase in turbine efficiency of about 0.01 is indicated.

Hoyt, Jack W.↗
NASA NTRS2006

Development and Testing of an Axial Halbach Magnetic Bearing

The NASA Glenn Research Center has developed and tested a revolutionary Axial Halbach Magnetic Bearing. The objective of this work is to develop a viable non-contact magnetic thrust bearing utilizing Halbach arrays for all-electric flight, and many other applications. This concept will help to reduce harmful emissions, reduce the Nation s dependence on fossil fuels and mitigate many of the concerns and limitations encountered in conventional axial bearings such as bearing wear, leaks, seals and friction loss. The Axial Halbach Magnetic Bearing is inherently stable and requires no active feedback control system or superconductivity as required in many magnetic bearing designs. The Axial Halbach Magnetic Bearing is useful for very high speed applications including turbines, instrumentation, medical systems, computer memory systems, and space power systems such as flywheels. Magnetic fields suspend and support a rotor assembly within a stator. Advanced technologies developed for particle accelerators, and currently under development for maglev trains and rocket launchers, served as the basis for this application. Experimental hardware was successfully designed and developed to validate the basic principles and analyses. The report concludes that the implementation of Axial Halbach Magnetic Bearings can provide significant improvements in rotational system performance and reliability.

Eichenberg, Dennis J.↗
DOE OSTI2020

Development of a Model Correlating Axial HEPA Filter Performance Between Elevated and Standard Conditions

The ASME AG-1 Code specifies minimum rated airflow based on standard cubic feet per minute (SCFM) for axial high efficiency particulate air (HEPA) filters and actual cubic feet per minute (ACFM) for radial HEPA filters with corresponding maximum pressure drop. A quantitative analysis can be performed to demonstrate the variation in filter efficiency and develop a correlation of performance between axial filters subjected to ACFM and SCFM. This study illustrates the variation in filter efficiency of axial HEPA filters subjected to ACFM and SCFM flow rate conditions at varying atmospheric pressures. It also presents the methods used to calculate correction factors to convert filter efficiency and pressure drop from elevated to standard conditions. The Axial Large Scale Test Stand (ALSTS) in the Institute for Clean Energy Technology (ICET) at Mississippi State University has been utilized to control aerosol concentration, flowrate, atmospheric pressure, relative humidity, and temperature. The filter test matrix consists of axial HEPA filters rated at 1,000 and 1,500 CFM with varying filter pack types. Each filter is subjected to varying pressures of 14.70 psi, 13.55 psi, 12.40 psi, and 11.25 psi, temperatures of 70 deg. F, 110 deg. F, and 150 deg. F, and relative humidities of 50% and 80%, resulting in twenty-four unique testing points. The corresponding SCFM flow rates are computed for each point in order to form a comparison. Evaluation of the effects of designating ACFM or SCFM will be based upon the filter efficiencies of generated Dioctyl Phthalate (DOP) particles at a diameter of 0.3 micrometers. The results show filter efficiency decreasing as atmospheric pressure decreases due to increased filter face velocity. A correlation model is developed to convert filter efficiency and pressure drop at elevated conditions to those of standard pressure, relative humidity, and temperature.

42 ENGINEERING↗
DOE OSTI2023

A Review of Axial Flux Permanent Magnet Machine Technology

Axial flux permanent magnet machines (AFPM) are popular for applications that benefit from high torque density and an axially compact form factor, such as in-wheel traction drives. Although the radial flux permanent magnet machine (RFPM) and the AFPM work based on the same underlying principle, the differences in their geometry introduce complexities in analysis of the AFPM. In this paper, the different AFPM design variants, their sizing approaches, computationally efficient design optimization techniques, and manufacturing techniques reported in literature are reviewed. In addition to classical AFPM machines, emerging variants and research opportunities with potential to push the boundaries of electric machine technology are reviewed. Furthermore, these include bearingless AFPMs, magnetically geared AFPMs, and combined radial-axial flux machines.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

In situ measurement of three-dimensional intergranular stress localizations and grain yielding under elastoplastic axial-torsional loading

The three-dimensional grain-averaged response of solid bar samples under non-proportional (NP) elastoplastic axial-torsional loading was investigated using in situ high energy diffraction microscopy (HEDM) and companion crystal plasticity finite element (CPFE) modeling. Important stress metrics including applied shear (σ θZ ) and axial (σ ZZ ) stress tensor components, stress and stress deviator tensor invariants (I 1 , J 2 , and J 3 ), von Mises equivalent stress (σ$^{grain}_{VM}$), maximum resolved shear stress (mRSS), stress triaxiality (η), and lode angle parameter ($\barθ$) values were tracked for ~300 grains under two different loading conditions: (1) Torsion-dominated loading (low NP) and (2) Tension-torsion loading (high NP) in equiatomic NiCoCr, a representative multicomponent face-centered cubic (FCC) superalloy. Overall, significant stress localizations existed within both samples as evidenced by the radial dependence of grain-resolved σ θZ , σ$^{grain}_{VM}$, and J 2 ; by comparison, I 1 , J 3 , η, and $\barθ$ metrics did not show discernible trends within the volume. These stress localizations reveal a complex interplay between axial and shear stress components (e.g., stress coupling) resulting in grain yielding near the sample surface largely driven by shear stress, whereas internal grain yielding was largely accommodated by axial stress. Grain-resolved stress localization trends were described well by the CPFE model, although some discrepancies in magnitude occurred, particularly for volumetric stress metrics (I 1 and η) due to initial type II residual stress distributions. The superposition of initial residual stress states onto CPFE grain-resolved data significantly improved model accuracy for η. This suggests that residual stresses more strongly influence the simulation of volumetric rather than deviatoric (yield) stress metrics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fuel Stratification Influence on NO x Emission in a Premixed Axial Reacting Jet-in-Crossflow at High Pressure

Three reacting jet-in-crossflow (JiC) methane/air flames were numerically investigated in a lean axially staged combustor at a pressure of five atmospheres. A detailed chemistry Star-CCM+ computational fluid dynamics (CFD) model was used with 53 species considered and the result of turbulence-governed finite-rate modeling was validated with in-house experimental data. An optically accessible test section features three side windows, allowing local flow and flame analysis with particle image velocimetry (PIV) and CH* chemiluminescence as well as pressure, temperature, and species exit measurements. The research objective was to predict and verify NO x formation of the premixed 12.7 mm axial jet. Three headend temperature levels were investigated along with three premixed jets at lean (φ Jet = 0.75), near-stoichiometric (φ Jet = 1.07), and rich (φ Jet = 1.78) axial fuel line equivalence ratio. Based on the matching exit emission concentration, global emission benefits were investigated by adjustment of the fuel stratification. The perfectly premixed methane/air flames of this study were shown to ignite at the lee-side of the jet. For the elevated headend temperature level T = 1800 K, the flame extended beyond the windward jet trajectory and caused high axial NO production. For industry application, a firing temperature of 1920 K was achieved with a NO x optimized fuel split of 25%, combining a lean headend (φ Headend = 0.61) with a rich (φ Jet = 1.78) jet equivalence ratio. As a result, this operating point allowed minimization of the combustor residence time at temperatures above 1700 K as well as combustion in a compact flame at the jet lee-side along the counter rotating vortex pair.

03 NATURAL GAS↗
DOE OSTI2025

Implementing Fuel Cladding Bonding and Assessing its Impact on Axial Gas Communication

Fuel rods irradiated in light-water reactors to burnup values above 45 MWd/kgU are subject to the formation of a chemical and mechanical bond between the fuel and cladding upon gap closure. The formation of the bond subsequently inhibits the ability of fission gases released from the fuel to flow freely to the plenum of the rod. The flowing of gases within fuel rods is referred to as axial gas communication. During transients, such as loss of coolant accidents, the bond may influence cladding deformation prior to breaking. Upon bond breakage, gases are able to more freely communicate to the lower pressure regions of the rod. The impact of bonding on gas communication and the ballooning behavior of the cladding during a loss of coolant accident is of interest to the nuclear industry in support of burnup extension for the existing light-water reactor fleet. In this report, a model to capture the effects of fuel cladding bonding in the BISON fuel performance code is presented. The theory of the model along with implementation testing is provided. A summary of a previously developed axial gas communication is given to set the stage for how the two models may be coupled together. A full-length pressurized-water reactor fuel rod demonstration is highlighted to evaluate the impact of including bonding on axial gas communication calculations using a preliminary coupling methodology. An overview of the next steps regarding the modeling of bonding, axial gas communication, and a more tightly coupled framework is also provided.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2017

Impact of Wake Dispersion on Axial Compressor Performance

Rotor wake dispersion in a low-speed, one and half stage axial compressor is investigated in detail with a Large Eddy Simulation (LES). The primary focus is to quantify the total pressure recovery due to wake stretching and the total pressure loss from the rotor wake interaction with the stator blade boundary layer. The relative magnitude of the aerodynamic loss due to these two effects is examined at several radial locations. The spacing between the rotor and the stator was varied from 29% to 112% of the rotor axial chord at the mid span to investigate the effects of rotor wake decay before entering the stator passage. The current analysis indicates that the efficiency through the compressor stage is increased about 0.5% when the spacing between the rotor and the stator is decreased from 112% to 29% of the rotor axial chord at mid-span. 22% of the efficiency gain from the narrower axial gap is due to the wake recovery and 63% is due to the stronger unsteady pressure field at the exit of the rotor due to stage interaction. Total pressure loss/recovery across the stator varies significantly in the radial direction for the current compressor, which has a much lower aspect ratio. The total pressure recovery due to wake stretching is larger than the total pressure loss due to the unsteady boundary layer development on the stator blade from 20% to 35% of the span from the hub for 29% spacing and from 35% to 55% of the span for 112% spacing. Above 50% of the span, rotor tip clearance flow affects wake dispersion and the overall wake recovery is less than expected.

Axial Compressor↗
DOE OSTI2023

Measurement of the axial vector form factor from antineutrino–proton scattering

Scattering of high energy particles from nucleons probes their structure, as was done in the experiments that established the non-zero size of the proton using electron beams. The use of charged leptons as scattering probes enables measuring the distribution of electric charges, which is encoded in the vector form factors of the nucleon. Scattering weakly interacting neutrinos gives the opportunity to measure both vector and axial vector form factors of the nucleon, providing an additional, complementary probe of their structure. The nucleon transition axial form factor, F A , can be measured from neutrino scattering from free nucleons, ν μ n → μ – p and ν¯ μ p → μ + n , as a function of the negative four-momentum transfer squared (Q 2 ). Up to now, FA(Q 2 ) has been extracted from the bound nucleons in neutrino–deuterium scattering, which requires uncertain nuclear corrections. Here we report the first high-statistics measurement, to our knowledge, of the ν¯ μ p → μ + n cross-section from the hydrogen atom, using the plastic scintillator target of the MINERvA experiment, extracting F A from free proton targets and measuring the nucleon axial charge radius, r A , to be 0.73 ± 0.17 fm. The antineutrino–hydrogen scattering presented here can access the axial form factor without the need for nuclear theory corrections, and enables direct comparisons with the increasingly precise lattice quantum chromodynamics computations. Finally, the tools developed for this analysis and the result presented are substantial advancements in our capabilities to understand the nucleon structure in the weak sector, and also help the current and future neutrino oscillation experiments to better constrain neutrino interaction models.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Axial confinement of wire array Z-pinch precursor plasmas by a pulsed magnetic mirror field

A novel wire-array Z-pinch platform has been developed to study the effect of a pulsed magnetic mirror field on a collisional high energy density plasma. The mirror is driven in series with the Z-pinch target and, therefore, scales with driver current. Axial confinement is observed based on visible imaging and axial flow velocity measurements. The presence of axial compressing J xB force is determined indirectly based on Thomson scattering and interferometry measurements and corroborated by three-dimensional extended-MHD simulations. Compared to non-magnetized wire array Z-pinch, a modified pulsed mirror configuration is observed to increase precursor plasma thermal energy density by about 30%. If optimized, such a configuration could potentially improve magnetized liner inertial fusion performance by reducing axial plasma end loss.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Nucleon axial and pseudoscalar form factors using twisted-mass fermion ensembles at the physical point

We compute the nucleon axial and pseudoscalar form factors using three N f = 2 + 1 + 1 twisted-mass fermion ensembles with all quark masses tuned to approximately their physical values. The values of the lattice spacings of these three physical point ensembles are 0.080, 0.068, and 0.057 fm and spatial sizes 5.1, 5.44, and 5.47 fm, respectively, yielding m π L > 3.6 . Convergence to the ground-state matrix elements is assessed using multistate fits. We study the momentum dependence of the three form factors and check the partially conserved axial-vector current (PCAC) hypothesis and the pion pole dominance (PPD). We show that in the continuum limit, the PCAC and PPD relations are satisfied. We also show that the Goldberger-Treimann relation is approximately fulfilled and determine the Goldberger-Treiman discrepancy. Our final results are g A = 1.245 ( 28 ) ( 14 ) for the nucleon axial charge, ⟨ r A 2 ⟩ = 0.339 ( 48 ) ( 06 ) fm 2 for the axial radius, g π N N ≡ lim Q 2 → − m π 2 G π N N ( Q 2 ) = 13.25 ( 67 ) ( 69 ) for the pion-nucleon coupling constant, and G P ( 0.88 m μ 2 ) ≡ g P * = 8.99 ( 39 ) ( 49 ) for the induced pseudoscalar form factor at the muon capture point. Published by the American Physical Society 2024

Astronomy & Astrophysics↗
DOE OSTI2026

Nucleon axial form factor from elementary target data

Precise neutrino-nucleon amplitudes are essential ingredients for predicting neutrino event rates in current and upcoming long-baseline neutrino oscillation experiments. A common neutrino interaction with a low reaction threshold and with most of the energy carried by two final state particles is quasielastic scattering, for which the nucleon axial form factor, 𝐹 𝐴⁡ (𝑄 2 ), is a dominant source of uncertainty. Improvements to the nucleon axial form factor rely on neutrino scattering data with elementary targets to reduce or eliminate the need for nuclear modeling systematics. This work examines constraints on the nucleon axial form factor that can be achieved from datasets of neutrino scattering on deuterium targets, Lattice QCD predictions, and from the recent hydrogen target data from the MINERvA Collaboration. Significant tension is found between hydrogen and deuterium target data, suggesting that extractions from deuterium underestimate both the central value and uncertainty of the form factor. Parametrizations for and uncertainties of the nucleon axial form factor using the 𝑧 expansion are provided.

FOS: Physical sciences↗
DOE OSTI2025

Evolution of the electrothermal instability from thick rod z pinches subject to dynamically and statically applied axial magnetic field

LDRD Project 229427 aimed to determine how electrothermal instability (ETI) driven heating on a z-pinch rod pulsed with intense current evolves under mixed magnetic field (azimuthal + axial) conditions, which is pertinent to pulsed-power-driven magnetically-insulated transmission lines and physics targets. Experiments focused on diagnosing ETI-driven heating from deliberately-machined and well-characterized micron-scale surface defects (referred to as engineered defects or ED). Prior to the start of this project, understanding of how unmagnetized (B z =0) ED evolve had been obtained—simulations largely reproduce the experimentally observed high temperature spots which develop at the poles of bare/uncoated ED. Project 229427 extended the Mykonos Facility ED experimental platform to include axial field. In the first class of experiments, axial field was provided “dynamically” via a helical return can (HRC). In this case, B z and B θ rise at the same rate. Generally, the HRC generated magnetic field at a fixed polarization angle Φ B =arctan(B z /B θ )=15° on the rod's surface. In the second class of experiments, axial field was provided “statically” via a slow-rising (millisecond) external Helmholtz coil pair. In this case, B z was effectively constant/static throughout the 100 ns rise of the Mykonos current. For either case, a primary goal was to determine whether ETI provides a helical seed perturbation for the subsequent growth of the helical magneto Rayleigh-Taylor modes observed in MagLIF (static B z ) and dynamic screw pinch (DSP, dynamic B z ) experiments. When dynamic field was applied using an HRC, emissions from individual ED aligned toward Φ B , while emissions from ED within pairs elongated and preferentially merged along Φ B . These data strongly support that for a randomized defect distribution, heating from nearby current-density perturbations will favorably merge about Φ B to generate an extended seed perturbation that aligns toward the surface-field polarization, and this may impact the orientation of subsequent MRT growth on imploding liners. The results from the static field experiments were largely inconclusive, as any ETI heating rotation, if present, was obscured/overwhelmed by local/random heating from ED rim imperfections.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗