Search NASA⌕ Search

SEARCH · Search NASA

Results for “bleed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Experimental investigation of a two-dimensional shock-turbulent boundary layer interaction with bleed

The two-dimensional interaction of an oblique shock wave with a turbulent boundary layer that included the effect of bleed was examined experimentally using a shock generator mounted across a supersonic wind tunnel. The studies were performed at Mach numbers 2.5 and 2.0 and unit Reynolds number of approximately 2.0 x 10 to the 7th/meter. The study includes surface oil flow visualization, wall static pressure distributions and boundary layer pitot pressure profiles. In addition, the variation of the local bleed rates were measured. The results show the effect of the bleed on the boundary layer as well as the effect of the flow conditions on the local bleed rate.

Hingst, W. R.↗
NASA NTRS1993

A lag model for turbulent boundary layers developing over rough bleed surfaces

Boundary layer mass removal (bleed) through spanwise bands of holes on a surface is used to prevent or control separation and to stabilize the normal shock in supersonic inlets. The addition of a transport equation lag relationship for eddy viscosity to the rough wall algebraic turbulence model of Cebeci and Chang was found to improve agreement between predicted and measured mean velocity distributions downstream of a bleed band. The model was demonstrated for a range of bleed configurations, bleed rates, and local free stream Mach numbers. In addition, the model was applied to the boundary layer development over acoustic lining materials for the inlets and nozzles of commercial aircraft. The model was found to yield accurate results for integral boundary layer properties unless there was a strong adverse pressure gradient.

Lee, J.↗
NASA NTRS1953

Acceleration of high-pressure-ratio single-spool turbojet engine as determined from component performance characteristics I : effect of air bleed at compressor outlet

An analytical investigation was made to determine from component performance characteristics the effect of air bleed at the compressor outlet on the acceleration characteristics of a typical high-pressure-ratio single-spool turbojet engine. Consideration of several operating lines on the compressor performance map with two turbine-inlet temperatures showed that for a minimum acceleration time the turbine-inlet temperature should be the maximum allowable, and the operating line on the compressor map should be as close to the surge region as possible throughout the speed range. Operation along such a line would require a continuously varying bleed area. A relatively simple two-step area bleed gives only a small increase in acceleration time over a corresponding variable-area bleed. For the modes of operation considered, over 84 percent of the total acceleration time was required to accelerate through the low-speed range ; therefore, better low-speed compressor performance (higher pressure ratios and efficiencies) would give a significant reduction in acceleration time.

ENGINES, TURBOJET↗
NASA NTRS1993

The 3-D CFD modeling of gas turbine combustor-integral bleed flow interaction

An advanced 3-D Computational Fluid Dynamics (CFD) model was developed to analyze the flow interaction between a gas turbine combustor and an integral bleed plenum. In this model, the elliptic governing equations of continuity, momentum and the k-e turbulence model were solved on a boundary-fitted, curvilinear, orthogonal grid system. The model was first validated against test data from public literature and then applied to a gas turbine combustor with integral bleed. The model predictions agreed well with data from combustor rig testing. The model predictions also indicated strong flow interaction between the combustor and the integral bleed. Integral bleed flow distribution was found to have a great effect on the pressure distribution around the gas turbine combustor.

Chen, D. Y.↗
NASA NTRS1994

YAV-8B reaction control system bleed and control power usage in hover and transition

Using a calibrated Rolls-Royce Pegasus engine and existing aircraft instrumentation and pressure taps, total and individual nozzle reaction control system (RCS) bleed flow rates have been measured on a YAV-8B Harrier during typical short takeoff, transition, hover, and vertical landing maneuvers. RCS thrust forces were calculated from RCS nozzle total pressure measurements, and control power was determined from the moments produced by these thrusts and the aircraft's moments of inertia. These data document the characteristics of the YAV-8B RCS with its basic stability augmentation system (SAS) engaged. Advanced control system designs for the YAV-8B can be compared to the original SAS based on the total bleed use and the percentage of available bleed used. In addition, the peak and mean values of the bleed and control power data can be used for sizing the reaction controls for a future short takeoff and vertical landing (STOVL) aircraft.

Borchers, Paul F.↗
NASA NTRS1997

Porous and Microporous Honeycomb Composites as Potential Boundary-Layer Bleed Materials

Results of an experimental investigation are presented in which the use of porous and microporous honeycomb composite materials is evaluated as an alternate to perforated solid plates for boundary-layer bleed in supersonic aircraft inlets. The terms "porous" and "microporous," respectively, refer to bleed orifice diameters roughly equal to and much less than the displacement thickness of the approach boundary-layer. A Baseline porous solid plate, two porous honeycomb, and three microporous honeycomb configurations are evaluated. The performance of the plates is characterized by the flow coefficient and relative change in boundary-layer profile parameters across the bleed region. The tests were conducted at Mach numbers of 1.27 and 1.98. The results show the porous honeycomb is not as efficient at removing mass compared to the baseline. The microporous plates were about equal to the baseline with one plate demonstrating a significantly higher efficiency. The microporous plates produced significantly fuller boundary-layer profiles downstream of the bleed region for a given mass flow removal rate than either the baseline or the porous honeycomb plates.

Davis, D. O.↗
NASA NTRSDate not supplied

Utilizing Electrical Power Extraction for Stability Bleed Reduction within Gas Turbine Engines

This paper studies the role of power extraction in gas turbine stability and how an engine may be designed to utilize this extraction to replace engine stability bleed requirements with electrical system requirements. The considered engine architecture contains two engine spools and a power turbine spool. In the baseline, low-pressure compressor stall margin is maintained by bleed air from the back of the low-pressure compressor, which is then dumped to the bypass. Power extraction from the high-pressure and low-pressure shafts are then utilized as a replacement for this bleed. This study considers component performance, sizing, efficiency, and operability, but does not consider weight or cost. Analysis within this paper is general and the concepts could be applied to other dual spool engine types, including a turbofan. Results show it is possible to completely remove the stability bleed between the low pressure and high-pressure compressor by utilizing a 35% power extraction from the high-pressure shaft or a 1.5% power extraction from the low-pressure turbine.

Gas Turbine↗
NASA NTRSDate not supplied

Utilizing Electrical Power Extraction for Stability Bleed Reduction within Gas Turbine Engines

This paper studies the role of power extraction in gas turbine stability and how an engine may be designed to utilize this extraction to replace engine stability bleed requirements with electrical system requirements. The considered engine architecture contains two engine spools and a power turbine spool. In the baseline, low-pressure compressor stall margin is maintained by bleed air from the back of the low-pressure compressor, which is then dumped to the bypass. Power extraction from the high-pressure and low-pressure shafts are then utilized as a replacement for this bleed. This study considers component performance, sizing, efficiency, and operability, but does not consider weight or cost. Analysis within this paper is general and the concepts could be applied to other dual spool engine types, including a turbofan. Results show it is possible to completely remove the stability bleed between the low pressure and high-pressure compressor by utilizing a 35% power extraction from the high-pressure shaft or a 1.5% power extraction from the low-pressure turbine.

Gas Turbine↗
NASA NTRS1973

Minimizing boundary layer bleed for a mixed compression inlet

An experimental investigation of a full scale mixed compression inlet sized for the TF30-P-3 turbofan engine was conducted at Mach 2.5 and 2.0 operating conditions. The two cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery exceeded 0.90 with only 0.02 centerbody bleed mass-flow ratio and zero cowl bleed. A centerbody bleed of approximately 0.05 gave a maximum inlet unstart angle-of-attack of 6.85 deg. Inlet performance and angle-of-attack tolerance is presented for operation at Mach 2.5 and 2.0.

Wasserbauer, J. F.↗
NASA NTRS1973

Minimizing boundary layer bleed for a mixed compression inlet

An experimental investigation of a full scale mixed compression inlet sized for the TF30-P-3 turbofan engine was conducted at Mach 2.5 and 2.0 operating conditions. The two cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery exceeded 0.90 with only 0.02 centerbody bleed mass-flow ratio and zero cowl bleed. A centerbody bleed of approximately 0.05 gave a maximum inlet unstart angle-of-attack of 6.85 deg. Inlet performance and angle-of-attack tolerance is presented for operation at Mach 2.5 and 2.0.

Wasserbauer, J. F.↗
NASA NTRS1975

Evaluation by step response tests of prototype relief valves designed for YF-12 inlet stability bleed system

Two stability bleed system relief valves were tested in a special dynamic test facility. These poppet valves are prototypes for a stability bleed system designed for use in a YF-12 flight inlet. One valve is unshielded, while the other has a special shield to eliminate the flow effect pressures on the piston. The tests determined the size of a damping orifice to be used during wind tunnel tests of the bleed system and verified an analog simulation of the valves. The effects of initial pressure level, pressure step size, and spring rate were investigated.

Dustin, M. O.↗
NASA NTRS1980

Reduced bleed air extraction for DC-10 cabin air conditioning

It is noted that a significant fuel savings can be achieved by reducing bleed air used for cabin air conditioning. Air in the cabin can be recirculated to maintain comfortable ventilation rates but the quality of the air tends to decrease due to entrainment of smoke and odors. Attention is given to a development system designed and fabricated under the NASA Engine Component Improvement Program to define the recirculation limit for the DC-10. It is shown that with the system, a wide range of bleed air reductions and recirculation rates is possible. A goal of 0.8% fuel savings has been achieved which results from a 50% reduction in bleed extraction from the engine.

Newman, W. H.↗
NASA NTRS1992

Three-dimensional shock-wave/boundary-layer interactions with bleed through a circular hole

Computations were performed to study three-dimensional (3-D), shock-wave/boundary-layer interactions on a flat plate in which fluid in the boundary layer was bled through a circular hole into a plenum to control shock-wave induced separation. Results are presented which show the details of the 3-D flowfield about the bleed hole and how bleed-hole placement relative to shock-wave impingement affect upstream, spanwise, and downstream influence lengths. This study revealed an underlying mechanisms by which bleed holes can affect shock-wave/boundary-layer interactions. This investigation is based on the ensemble-averaged, "full-compressible" Navier-Stokes equations closed by the Baldwin-Lomax turbulence model. Solutions to these equations were obtained by an implicit finite-volume method based on the partially-split, two-factored algorithm of Steger.

Rimlinger, M. J.↗
NASA NTRS1993

Numerical study of shock-wave/boundary-layer interactions with bleed

A numerical study was conducted to investigate how bleed through a two-dimensional slot affects shock-wave induced, boundary-layer separation on a flat plate. This study is based on the ensemble-averaged, compressible, Navier-Stokes equations closed by the Baldwin-Lomax, algebraic turbulence model. The algorithm used to obtain solutions was the implicit, partially split, two-factored scheme of Steger. This study examined the effects of the following parameters in controlling shock-wave induced flow separation: location of slot in relation to where the incident shock wave impinged on the boundary layer, size of slot in relation to the boundary-layer thickness, number of slots, spacings between slots, and strength of the incident shock wave. This study also showed the nature of the very complex flowfield about the slot or slots and how the plenum affects the bleed process. The results of this study are relevant to problems where bleed is used to control shock-wave induced, boundary-layer separation (e.g., inside jet engine inlets and wind tunnels).

Hahn, T. O.↗
NASA NTRS1951

Calculated effects of turbine rotor-blade cooling-air flow, altitude, and compressor bleed point on performance of a turbojet engine

Effects of air-cooling turbine rotor blades on performance of a turbojet engine were calculated for a range of altitudes from sea level to 40,000 feet and a range of coolant flows up to 3 percent of compressor air flow, for two conditions of coolant bleed from the compressor. Bleeding at required coolant pressure resulted in a sea-level thrust reduction approximately twice the percentage coolant flow and in an increase in specific fuel consumption approximately equal to percentage coolant flow. For any fixed value of coolant flow ratio the percentage thrust reduction and percentage increase in specific fuel consumption decreased with altitude. Bleeding coolant at the compressor discharge resulted in an additional 1 percent loss in performance at sea level and in smaller increase in loss of performance at higher altitudes.

TURBINE COOLING↗
NASA NTRS1992

Mechanisms of flow control with the unsteady bleed technique

The unsteady bleed technique (a.k.a. internal acoustic forcing) has been shown to be an effective method for control of separation on low Reynolds number airfoils, blunt-end cylinders aligned axially with the flow, cylinders aligned perpendicular to the flow, and forebody geometries at high angles of attack. In many of these investigations, the mechanism for the control has been attributed to enhancement of the shear layer (Kelvin-Helmholtz) instability by the unsteady component of the forcing. However, this is not the only possible mechanism, nor may it be the dominant mechanism under some conditions. In this work it is demonstrated that at least two other mechanisms for flow control are present, and depending on the location and the amplitude of the forcing, these may have significant impact on the flow behavior. Experiments were conducted on a right-circular cylinder with a single unsteady bleed slot aligned along the axis of the cylinder. The effects of forcing frequency, forcing amplitude, and slot location on the azimuthal pressure distribution were studied. The results suggest that a strong vortical structure forms near the unsteady bleed slot when the slot location is upstream of the boundary layer separation point. The structure is unsteady, since it is created by the unsteady forcing. The 'vortex' generates a sizeable pressure spike (C(sub p) = -3.0) in the time-averaged pressure field immediately downstream of the slot. In addition to the pressure spike, the boundary layer separation location moves farther downstream when the forcing is activated. Delay of the separation is believed to be a result of enhancing the Kelvin-Helmholtz instability. When forcing is applied in a quiescent wind tunnel, a weak low-pressure region forms near the slot that is purely the result of the second-order streaming effect.

Williams, D. R.↗
NASA NTRS1995

A procedure for automating CFD simulations of an inlet-bleed problem

A procedure was developed to improve the turn-around time for computational fluid dynamics (CFD) simulations of an inlet-bleed problem involving oblique shock-wave/boundary-layer interactions on a flat plate with bleed into a plenum through one or more circular holes. This procedure is embodied in a preprocessor called AUTOMAT. With AUTOMAT, once data for the geometry and flow conditions have been specified (either interactively or via a namelist), it will automatically generate all input files needed to perform a three-dimensional Navier-Stokes simulation of the prescribed inlet-bleed problem by using the PEGASUS and OVERFLOW codes. The input files automatically generated by AUTOMAT include those for the grid system and those for the initial and boundary conditions. The grid systems automatically generated by AUTOMAT are multi-block structured grids of the overlapping type. Results obtained by using AUTOMAT are presented to illustrate its capability.

Chyu, Wei J.↗
NASA NTRS1995

Numerical simulation of supersonic flow using a new analytical bleed boundary condition

A new analytical bleed boundary condition is used to compute flowfields for a strong oblique shock wave/boundary layer interaction with a baseline and three bleed rates at a freestream Mach number of 2.47 with an 8 deg shock generator. The computational results are compared to experimental Pitot pressure profiles and wall static pressures through the interaction region. An algebraic turbulence model is employed for the bleed and baseline cases, and a one equation model is also used for the baseline case where the boundary layer is separated.

Harloff, G. J.↗