Results for “boundary layer transition, acoustics” — Page 3

NASA NTRS1985

Further results of natural laminar flow flight test experiments

Flight test experiments were conducted to measure the extent and nature of natural laminar flow on a smoothed test region of a swept-wing business jet wing. Surface hot film anemometry and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Engine noise was monitored by a microphone attached to the wing surface to study possible acoustic effects on stability of the laminar boundary layer. Side-slip conditions were flown to simulate changes in effective wing sweep. Flight instrumentation and ground data analysis techniques and a method for measuring intermittency of turbulence are described. Correlation was obtained between the hot film gage signals and chemicals for transition detection. Cross-flow vortices were observed for some flight conditions. Results of spectral and statistical analysis of the hot film signals for various flight test conditions are presented.

Wentz, W. H., Jr.↗

NASA NTRS2002

Phase Synchronization and Desynchronization of Structural Response Induced by Turbulent and External Sound

Acoustic and turbulent boundary layer flow loadings over a flexible structure are used to study the spatial-temporal dynamics of the response of the structure. The stability of the spatial synchronization and desynchronization by an active external force is investigated with an array of coupled transducers on the structure. In the synchronous state, the structural phase is locked, which leads to the formation of spatial patterns while the amplitude peaks exhibit chaotic behaviors. Large amplitude, spatially symmetric loading is superimposed on broadband, but in the desynchronized state, the spectrum broadens and the phase space is lost. The resulting pattern bears a striking resemblance to phase turbulence. The transition is achieved by using a low power external actuator to trigger broadband behaviors from the knowledge of the external acoustic load inducing synchronization. The changes are made favorably and efficiently to alter the frequency distribution of power, not the total power level. Before synchronization effects are seen, the panel response to the turbulent boundary layer loading is discontinuously spatio-temporally correlated. The stability develops from different competing wavelengths; the spatial scale is significantly shorter than when forced with the superimposed external sound. When the external sound level decreases and the synchronized phases are lost, changes in the character of the spectra can be linked to the occurrence of spatial phase transition. These changes can develop broadband response. Synchronized responses of fuselage structure panels have been observed in subsonic and supersonic aircraft; results from two flights tests are discussed.

Maestrello, Lucio↗

NASA NTRS2007

Spatial Evolution of Resonant Harmonic Mode Triads in a Blasius Boundary Layer

Blasius boundary layer evolution is studies by means of bicoherence calculations. The layer is acoustically excited at the T-S frequency to provide a controlled transition. Measurements are made using a smooth surface as well as various roughness patterns. The bicoherence calculations are used to determine the extent to which frequency resonant velocity fluctuation waves can participate in energy exchange. The emphasis is on downstream variation of the individual interactions among harmonic modes. A limited picture of the role of quadratic wave interactions is revealed.

Davila, Jose B.↗

NASA NTRS2011

Effects of Nose Bluntness on Hypersonic Boundary-Layer Receptivity and Stability Over Cones

The receptivity to freestream acoustic disturbances and the stability properties of hypersonic boundary layers are numerically investigated for boundary-layer flows over a 5 straight cone at a freestream Mach number of 6.0. To compute the shock and the interaction of the shock with the instability waves, the Navier-Stokes equations in axisymmetric coordinates were solved. In the governing equations, inviscid and viscous flux vectors are discretized using a fifth-order accurate weighted-essentially-non-oscillatory scheme. A third-order accurate total-variation-diminishing Runge-Kutta scheme is employed for time integration. After the mean flow field is computed, disturbances are introduced at the upstream end of the computational domain. The appearance of instability waves near the nose region and the receptivity of the boundary layer with respect to slow mode acoustic waves are investigated. Computations confirm the stabilizing effect of nose bluntness and the role of the entropy layer in the delay of boundary-layer transition. The current solutions, compared with experimental observations and other computational results, exhibit good agreement.

Kara, Kursat↗

NASA NTRS2021

Boundary-layer Instability Measurements on a Cone at Freestream Mach 3.5

An experimental study was conducted in the NASA (National Aeronautics and Space Administration) Langley Supersonic Low-Disturbance Tunnel to investigate naturally-occurring instabilities in a supersonic boundary layer on a 7◦ half-angle cone at nominal freestream conditions: Mach 3.5, total temperature of 299.8K, and unit Reynolds numbers (millions per m) of 9.89, 13.85, 21.77, and 25.73. Instability measurements were acquired under noisy-flow and quiet-flow conditions. Pitot-pressure and calibrated hot-wire measurements were obtained using a model-integrated traverse system to document the model flow field. In noisy-flow conditions, growth rates and mode shapes achieved good agreement between the measured results and linear stability theory (LST). The corresponding N factor at transition from LST is N ≈ 3.9. Under quiet-flow conditions, the most unstable first-mode instabilities as predicted by LST were measured, but this mode was not the dominant instability measured in the boundary layer. Instead, the dominant instabilities were less-amplified, low-frequency disturbances predicted by LST, and grew according to linear theory. These low-frequency unstable disturbances were initiated by freestream acoustic disturbances through a receptivity process believed to occur near the branch I location of the cone. Under quiet-flow conditions, the boundary layer remained laminar up to the last measurement station for the largest unit Reynolds number, implying a transition N factor of N > 8.5.

Boundary Layer↗

NASA NTRS2015

Receptivity of Hypersonic Boundary Layers to Acoustic and Vortical Disturbances (Invited)

Boundary-layer receptivity to two-dimensional acoustic and vortical disturbances for hypersonic flows over two-dimensional and axi-symmetric geometries were numerically investigated. The role of bluntness, wall cooling, and pressure gradients on the receptivity and stability were analyzed and compared with the sharp nose cases. It was found that for flows over sharp nose geometries in adiabatic wall conditions the instability waves are generated in the leading-edge region and that the boundary layer is much more receptive to slow acoustic waves as compared to the fast waves. The computations confirmed the stabilizing effect of nose bluntness and the role of the entropy layer in the delay of boundary layer transition. The receptivity coefficients in flows over blunt bodies are orders of magnitude smaller than that for the sharp cone cases. Wall cooling stabilizes the first mode strongly and destabilizes the second mode. However, the receptivity coefficients are also much smaller compared to the adiabatic case. The adverse pressure gradients increased the unstable second mode regions.

Balakumar, P.↗

NASA NTRS2016

Measurements in a Transitioning Cone Boundary Layer at Freestream Mach 3.5

An experimental study was conducted in the Supersonic Low-Disturbance Tunnel to investigate naturally-occurring instabilities in a supersonic boundary layer on a 7 deg half- angle cone. All tests were conducted with a nominal freestream Mach number of M(sub infinity) = 3:5, total temperature of T(sub 0) = 299:8 K, and unit Reynolds numbers of Re(sub infinity) x 10(exp -6) = 9:89, 13.85, 21.77, and 25.73 m(exp -1). Instability measurements were acquired under noisy- ow and quiet- ow conditions. Measurements were made to document the freestream and the boundary-layer edge environment, to document the cone baseline flow, and to establish the stability characteristics of the transitioning flow. Pitot pressure and hot-wire boundary- layer measurements were obtained using a model-integrated traverse system. All hot- wire results were single-point measurements and were acquired with a sensor calibrated to mass ux. For the noisy-flow conditions, excellent agreement for the growth rates and mode shapes was achieved between the measured results and linear stability theory (LST). The corresponding N factor at transition from LST is N 3:9. The stability measurements for the quiet-flow conditions were limited to the aft end of the cone. The most unstable first-mode instabilities as predicted by LST were successfully measured, but this unstable first mode was not the dominant instability measured in the boundary layer. Instead, the dominant instabilities were found to be the less-amplified, low-frequency disturbances predicted by linear stability theory, and these instabilities grew according to linear theory. These low-frequency unstable disturbances were initiated by freestream acoustic disturbances through a receptivity process that is believed to occur near the branch I locations of the cone. Under quiet-flow conditions, the boundary layer remained laminar up to the last measurement station for the largest Re1, implying a transition N factor of N greater than 8:5.

King, Rudolph A.↗

NASA NTRSDate not supplied

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗

NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗

NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗

NASA NTRS1987

The structure of separated flow regions occurring near the leading edge of airfoils including transition

All the time and effort was directed toward acquiring, reducing, and analyzing more hot-wire anemometer data. Some static pressure distribution data were also acquired to support the analysis of the velocity profile data. Laser Doppler Velocimetry data were not acquired due to equipment problems. Included were seven combinations of chord Reynolds number, angle of attack, and acoustic forcing using the NACA 663-018 airfoil. This research has as its objective the detailed documentation of the structure and behavior of the transitional separation bubble and the redeveloping boundary layer after reattachment over an airfoil at low Reynolds numbers. The intent is to further the understanding of the complex flow phenomena so that analytic methods for predicting their formulation and development can be improved. These analytic techniques have applications in the design and performance prediction of airfoils operating in the low Reynolds number flight regime.

Mueller, Thomas J.↗

NASA NTRS1992

Three-dimensional boundary-layer transition on a cone at Mach 3.5

A boundary-layer transition study on a sharp, 5 deg half-angle cone at various angles of attack was conducted at Mach 3.5. Transition data were obtained with and without significantly reduced freestream acoustic disturbance levels. A progressive downstream and upstream motion of the transition front on the windward and leeward rays, respectively, of the cone with angle of attack was observed for the high noise level data in agreement with data trends obtained in conventional ('noisy') wind tunnels. However, the downstream movement was not observed to the same degree for the low noise level data in the present study. Transition believed to be crossflow dominated was found to be less receptive to freestream acoustic disturbances than first-mode (Tollmien-Schlichting) dominated transition. The previously-developed crossflow transition Reynolds number criterion was found to be inadequate for the current case. An improved criterion is offered, which includes compressibility and flow-geometry effects.

King, R. A.↗

NASA NTRS1992

On the mechanism of turbulence suppression in free shear flows under acoustic excitation

Acoustic excitation at certain high frequencies has been known to suppress large amplitude fluctuations otherwise occurring naturally in various free shear flows. The phenomenon has been observed in flows with initially laminar or transitional boundary layers. An experimental investigation is conducted to consider two possibilities in regards to the mechanism of the effect. (1) The natural shear layer is self excited by the instability waves already developed in the upstream boundary layer. This is overridden when the shear layer is excited at its maximally unstable mode, causing the observed decrease in the intensities downstream. (2) The upstream boundary layer is in a transitional or buffeted laminar state, characterized by large amplitude unsteady fluctuations, which force the large fluctuations downstream. Excitation trips the upstream boundary layer to full turbulence, reduces the unsteady fluctuations, and thus causes the observed suppression of the intensities throughout the flowfield. The present experimental results refute either of these possibilities to be the general mechanism of the effect.

Zaman, K. B. M. Q.↗

NASA NTRS1992

On the mechanism of turbulence suppression in free shear flows under acoustic excitation

Acoustic excitation at certain high frequencies has been known to suppress large amplitude fluctuations otherwise occurring naturally in various free shear flows. The phenomenon has been observed in flows with initially laminar or transitional boundary layers. An experimental investigation is conducted to consider two possibilities in regards to the mechanism of the effect. (1) The natural shear layer is self excited by the instability waves already developed in the upstream boundary layer. This is overridden when the shear layer is excited at its maximally unstable mode, causing the observed decrease in the intensities downstream. (2) The upstream boundary layer is in a transitional or buffeted laminar state, characterized by large amplitude unsteady fluctuations, which force the large fluctuations downstream. Excitation trips the upstream boundary layer to full turbulence, reduces the unsteady fluctuations, and thus causes the observed suppression of the intensities throughout the flowfield. The present experimental results refute either of these possibilities to be the general mechanism of the effect.

Zaman, K. B. M. Q.↗

NASA NTRS1993

Characterization of cavity flow fields using pressure data obtained in the Langley 0.3-Meter Transonic Cryogenic Tunnel

Static and fluctuating pressure distributions were obtained along the floor of a rectangular-box cavity in an experiment performed in the LaRC 0.3-Meter Transonic Cryogenic Tunnel. The cavity studied was 11.25 in. long and 2.50 in. wide with a variable height to obtain length-to-height ratios of 4.4, 6.7, 12.67, and 20.0. The data presented herein were obtained for yaw angles of 0 deg and 15 deg over a Mach number range from 0.2 to 0.9 at a Reynolds number of 30 x 10(exp 6) per ft with a boundary-layer thickness of approximately 0.5 in. The results indicated that open and transitional-open cavity flow supports tone generation at subsonic and transonic speeds at Mach numbers of 0.6 and above. Further, pressure fluctuations associated with acoustic tone generation can be sustained when static pressure distributions indicate that transitional-closed and closed flow fields exist in the cavity. Cavities that support tone generation at 0 deg yaw also supported tone generation at 15 deg yaw when the flow became transitional-closed. For the latter cases, a reduction in tone amplitude was observed. Both static and fluctuating pressure data must be considered when defining cavity flow fields, and the flow models need to be refined to accommodate steady and unsteady flows.

Tracy, M. B.↗

NASA NTRS1986

Transition and separation control on a low-Reynolds number airfoil

The major problem associated with the aerodynamic performance of airfoils at low Reynolds numbers is the presence of extensive laminar boundary-layer separation resulting in a large increase in presssure drag and a decrease in lift. The rapid deterioration in airfoil characteristics can be largely eliminated by artificially controlling the flow through the introduction of suitable disturbances in the boundary layer such that transition occurs ahead of the anticipated laminar separation. This paper presents the results of wind-tunnel tests conducted on a 10-cm model of LRN (1)-1007 airfoil with passive (roughness trips) and active (acoustic excitation) controls to trigger transition and suppress separation. Significant improvements in the aerodynamic characteristics of the airfoil were observed. Results of this study for a chord Reynolds number range of 40,000 to 250,000 are presented in this paper.

Mangalam, S. M.↗

NASA NTRS1991

Mach 3.5 boundary-layer transition on a cone at angle of attack

Boundary-layer transition on a sharp 5-deg half-angle cone at incidence was investigated at Mach 3.5 in NASA's Supersonic Low-Disturbance Pilot Tunnel. The tests were conducted with low and high levels of freestream acoustic disturbance, and four angles of attack (alpha/theta-c = 0, 0.12, 0.4, and 0.8). Transition data, obtained with and without significantly reduced freestream acoustic disturbance levels, are compared with conventional ('noisy') wind-tunnel data. It was found that, under quiet flow conditions, there was no significant unit Reynolds number effect, whereas with noisy flow conditions, a significant unit Reynolds number effect was measured on and near the windward ray for alpha/theta-c values 0.4 and 0.8.

King, Rudolph A.↗

NASA NTRS2001

Qualitative Assessment of the Acoustic Disturbance Environment in the NASA LaRC 20-Inch MACH 6 Wind Tunnel

An experimental investigation was conducted on a 5-degree-half-angle cone with a flare in a conventional Mach 6 wind tunnel to examine the effect of facility noise on boundary layer transition. The effect of tunnel noise was inferred by comparing transition onset locations determined from the present test to that previously obtained in a Mach 6 quiet tunnel. Together, the two sets of experiments are believed to represent the first direct comparison of transition onset between a conventional and a quiet hypersonic wind tunnel using a common test model. In the present conventional hypersonic tunnel experiment, adiabatic wall temperatures were measured and heat transfer distributions were inferred on the cone flare model at zero degree angle of attack over a range of length Reynolds numbers (2 x 10(exp 6) to 10 x 10(exp 6)) which resulted in laminar and turbulent flow. Wall-to-total temperature ratio for the transient heating measurements and the adiabatic wall temperature measurements were 0.69 and 0.86, respectively. The cone flare nosetip radius was varied from 0.0001 to 0.125-inch to examine the effects of bluntness on transition onset. At comparable freestream conditions the transition onset Reynolds number obtained on the cone flare model in the conventional "noisy" tunnel was approximately 25% lower than that measured in the low disturbance tunnel.

Horvath, Thomas J.↗