Search NASA⌕ Search

SEARCH · Search NASA

Results for “carbonated MgO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Adsorption of CO on oxide and water ice surfaces - Implications for the Martian atmosphere

The adsorption of carbon monoxide (CO) on water ice and on the oxides Fe2O3, Fe3O4, Al2O3, SiO2, CaO, MgO, and TiO2 (rutile and anatase) has been investigated in a flow reactor. A mass spectrometer was employed as a detector to monitor the temporal concentrations of CO. Adsorption coefficients as large as 1 x 10 exp -4 were measured for CO on TiO2 solids in helium at 196 K. The fractional surface coverage for CO on TiO2 solids in helium was also determined to be approximately 10 percent at 196 K. The upper limits of the fractional surface coverage for the other oxides (Fe2O3, Fe3O4, Al2O3, SiO2, CaO, and MgO) and water ice were also measured to be less than 1 percent. The implications for the stability of CO2 in the Martian atmosphere and the 'CO hole' observed by the Phobos/ISM experiment are discussed.

Leu, M.-T.↗

Producing cement clinker assemblages in the system: CaO-SiO2-Al2O3-SO3-CaCl2-MgO

Highlights: • Alinite formation conditions are optimised. • Ye'elimite and alinite cannot be simultaneously produced. • Ternesite and chlormayenite are compatible at 1150 °C. • Alite is formed at a reduced temperature of 1300 °C. • Wadalite and chlorellestadite can incorporate chloride in cement clinker assemblages. The cement industry is carbon-intensive, and the valorisation of industrial side-streams/residuals for use as alternative raw materials can enable the cement industry to reduce its carbon footprint as well as promote resource efficiency. Apart from key clinker ingredients such as CaO, Al{sub 2}O{sub 3}, and SiO{sub 2}, industrial residues can also contain MgO, CaCl{sub 2}, and SO{sub 3}. Therefore, this study investigates the formation of cement clinker assemblages in the system CaO-SiO{sub 2}-Al{sub 2}O{sub 3}-SO{sub 3}-CaCl{sub 2}-MgO at temperatures ranging between 1100 and 1300 °C. The production of a clinker composed mainly of alinite and ye'elimite is first attempted; it is found that these phases cannot be simultaneously produced. Ternesite is also not compatible with alinite under the conditions studied. Wadalite is compatible with both ye'elimite and ternesite, while ternesite is also compatible with chlormayenite at 1150 °C. Additionally, the low-temperature formation of alite was also observed with the presence of CaCl{sub 2} in the raw-material mix.

36 MATERIALS SCIENCE↗

Size-Dependent Adsorption and Adhesion Energetics of Ag Nanoparticles on Graphene Films on Ni(111) by Calorimetry

Interest in the use of carbon supports for late transition metal nanoparticle catalysts has expanded rapidly due to the increasing importance of electrocatalysts for clean energy and environmental technologies and the use and storage of renewable electricity. Compared to oxide supports, almost nothing is known about the effect of metal nanoparticle size on the energies of the metal atoms within carbon-supported nanoparticles, yet these energies are crucial for understanding their surface reactivity and sintering kinetics. Here, the growth morphology and adsorption energetics of vapor-deposited Ag onto clean graphene/Ni(111) surfaces have been studied using a combination of single-crystal adsorption calorimetry (SCAC) and He + low-energy ion scattering (LEIS). The differential heat of Ag adsorption is 207 kJ/mol for making ~30 atom Ag particles on graphene terraces at 100 K and 16 kJ/mol higher for making ~9 atom Ag clusters at defect sites at the same temperature. The heat of adsorption increases rapidly with Ag coverage as 3D Ag nanoparticles nucleate and grow in size, asymptotically reaching within 5 kJ/mol of the bulk Ag sublimation enthalpy (285 kJ/mol) by 2 ML. The heats of adsorption and Ag nanoparticle densities from LEIS (~10 16 /m 2 ) were combined to provide the Ag/graphene adhesion energy (E adh = 1.8 J/m 2 in the large-particle limit) and the Ag chemical potential (μ) versus effective particle diameter (D). The Ag chemical potential was well-fitted by μ(D) = (3γ v /M – E adh )(1 + (1.5 nm)/D)(2V m /D), where γ v /M is the surface energy of bulk Ag and V m is its molar volume. The same equation is known to fit similar data for late transition metals on clean surfaces of metal oxide single crystals. The adhesion energy of Ag measured here on graphene falls within the wide range measured for Ag on those oxide surfaces and is almost as large as on the oxide that binds Ag particles most strongly, namely CeO 2 (111), which is well-known to be very effective at resisting catalyst deactivation by metal sintering. Furthermore, these results imply that carbon supports will be effective at resisting sintering and that Ag particles smaller than 6 nm on graphene will bind small adsorbed reaction intermediates more weakly than supports with weaker adhesion to Ag, like MgO(100).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Combined Strength of Thermodynamics and Comparative Planetology: Application of Activity Models to Core Formation in Terrestrial Bodies

Recent models for accretion of terrestrial bodies involve metal-silicate equilibrium as the metallic core formed during growth. Most elements considered are either refractory or well studied elements for which effects of pressure, temperature, oxygen fugacity, and metallic liquid composition are well known. There are a large number of elements that are both siderophile and volatile, whose fate in such models is unknown, largely due to a lack of data at comparable conditions and com-positions (FeNi core with light elements such as S, C, Si, and O). We have focused on Ge, In, As, Sb and determined the effect of Si and C on metal-silicate partitioning, and developed a thermo-dynamic model that allows application of these new data to a wide range of planetary bodies. New experiments: We have previously carried out experiments with FeSi metallic liquid at C-saturated conditions at 1600 and 1800 C [4]. In a new series of experiments we investigate the effect of Si in carbon-free systems at 1600 C for comparison. Experiments were carried out at 1 GPa in MgO capsules using the same basaltic starting composition as in previous studies. The MgO capsule reacts with the silicate melt to form more MgO-rich liquids that have 22-26 wt% MgO. Experimental met-als and silicates were analyzed using a combination of electron microprobe analysis and laser ablation ICP-MS. Results: The new results can be interpreted by considering Ge as an example, in the simple exchange equilibrium Fe + GeO = FeO + Ge, where the equilibrium constant Kd can be examined as a function of Si content of the metal. The slope of lnKd vs. (1-XSi) for this new series allows derivation of the epsilon interaction parameter for each of these four elements and Si (both C-saturated and C-free).All four elements have positive epsilon values, indicating that Si causes a decrease in the partition coefficients; values are 6.6, 6.5, 27.8 and 25.2 for In, Ge, As, and Sb, respectively, at 1 GPa and 1600 C. As an example of how large the effect of Si can be, these epsilon values correspond to activity coefficients (gamma) for As of 0.01 when XSi = 0, and up to gamma = 23 when XSi = 0.2. Combining these new results with previous determinations [5,6] of epsilon parameters for S and C for these elements allows us calculate activity of Ge, In, As, and Sb in Fe-Ni-Si-S-C-O metallic liquids. We apply this new model to sever-al terrestrial bodies such as Earth (Si-rich core), Mars (S-rich core), Moon (S-, C-, and Si-poor core), and Vesta, and examine the resulting core and mantle concentrations of these elements. Mantle concentrations of these four elements are well explained for Earth and Mars in models that call for mid-mantle equilibration between Si-bearing and S-bearing FeNi cores, respectively. Modeling results for the Moon and Vesta will also be presented.

Righter, K.↗

Shake loss intensities in x-ray photoelectron spectroscopy: Theory, experiment, and atomic composition accuracy for MgO and related compounds

The relative intensities of XPS core levels, scaled by their photoionization cross sections, are regularly used to determine sample atomic composition. Cross sections, however, give the intensity to all possible final states for the core ionizations, not just to the main peak. This includes all intrinsic satellite structure (shake states and, for open shell systems, the different ionic multiplets). In practice, for solids, this is usually experimentally impossible to determine accurately because such a satellite structure sits on the inelastically scattered electron background and cannot be easily separated. Therefore, usually, only the intensity of the main peak is used. This limits the ultimate possible accuracy of XPS composition determination. The purpose of the present paper is to examine the contributions that a theoretical analysis of losses of intensity can make to improve quantitation. For an MgO single crystal, we show that the correct stoichiometry of 1:1 can be recovered using the theoretical analysis of the experimental MgO peak ratio intensities. For materials with a sufficient bandgap for the XPS main peaks to be separated from the scattered background, the intensity of main peaks can often be accurately determined. Thus, if one uses theory to calculate that fraction of the total intensity lost from a main peak into all its satellite structure, the intensity of just main peaks could then be used to more accurately determine relative atom % composition. This work tests this approach using a single crystal MgO (50% Mg, 50% O) standard. Ab initio electronic structure theory of representative MgO clusters is used to determine Hartree–Fock wave functions for the ground state and final ionized states corresponding to the main Mg 2p and O1s XPS peaks of the oxide. The sudden approximation, SA, is used to determine the fractional losses from these main peaks to shake satellites, which is found to be greater for O1s than Mg2p. This results in predicted “apparent composition” for stoichiometric MgO of 55.2% Mg, 44.8% O instead of the true 50% Mg, 50% O. Equivalent theory for CaO results in a predicted apparent Ca value of 53.4%. Experimentally, using Mg2s or 2p intensity ratio to O1s, we find values between 52.2% and 56.0% Mg using two crystals and four different instrument electron pass energies. The average value of the measurements is 54.5% Mg when corrected for the presence of an adventitious carbon overlayer and slight surface hydroxide. Though this agreement with theory may be somewhat fortuitous, given the potential experimental errors, which are fully discussed, it is similar to that in our earlier study on LiF. We also present preliminary experimental data on Mg(OH) 2 and MgSO 4 , which show a similar trend of apparently higher than 50% Mg, but we have no theory values. We are not yet able to experimentally test for validation of the difference between apparent composition for MgO (55.2% Mg) and CaO (53.4% Ca), owing to significant carbonate formation at the surface of the single crystal CaO. Here, an important conclusion is that the theoretical determination of shake losses, obtained with ab initio wavefunctions and the SA, is likely to be a useful way to calibrate the accuracy and reliability of compositions obtained from XPS intensities and merits further study.

47 OTHER INSTRUMENTATION↗

Mining waste-driven carbon capture via ocean alkalinity enhancement

Ocean alkalinity enhancement (OAE) has emerged as a promising strategy to mitigate ocean acidification and reduce global warming. Traditional metal (e.g., critical materials) mining industries release alkaline waste via mining tailings with high concentrations (99.2%) of calcium and magnesium oxide (CaO, MgO). Incorporating mining waste into OAE processes is less energy intensive than processes relying on calcination of limestone for CaO production. The solubility limit of simulated mining waste in American Society for Testing and Materials (ASTM) seawater is 75 mg⋅L -1 , which can sequester 118 mg of carbon dioxide (CO 2 ). The solubility in seawater retrieved from Sunset Beach, FL was 25 mg⋅L -1 . Changes in pH, total alkalinity, and total inorganic carbon were analyzed to confirm the successful addition of simulated alkaline mining waste without the formation of secondary precipitation. This study proposes a new OAE strategy where a facility is developed nearby ocean waters that mixes alkaline waste with seawater. Subsequently, the seawater is met with previously captured, pure CO 2 to bring the pH back to 8.2 and eliminate the risks of pH shock and secondary precipitation. Technoeconomic analysis estimated an energy requirement of 1.4 GJ per ton of CO 2 stored that resulted in a processing cost of $\$$266 per ton of CO 2 sequestered (4.2 GJ per ton, $\$$807 per ton of CO 2 for real seawater). Results from this study underscore the potential for utilizing mining waste in OAE processes and provide a pathway for practical deployment.

Absorption↗

Magnesium production by molten salt electrolysis with liquid tin cathode and multiple effect distillation

Low-cost clean primary production of magnesium metal is important for its use in many applications, from light-weight structural components to energy technologies. This work describes new experiments and cost and emissions analysis for a magnesium metal production process. The process combines molten salt electrolysis of MgO using MgF₂-CaF₂ electrolyte and a reactive liquid tin cathode, with gravity-driven multiple effect thermal system (G-METS) distillation to separate out the magnesium product, and re-use of the tin. Electrolysis experiments with carbon anodes showed current yield above 90%, while a yttria-stabilized zirconia solid oxide membrane (SOM) anode experiment showed 84% current yield. G-METS distillation is an important component of the envisioned process. It can potentially lower costs and energy use considerably compared with conventional magnesium distillation. Techno-economic analysis including detailed mass and energy balances shows that this electrolyte composition could lower costs by utilizing CaO, which is the primary impurity in MgO, as the Hall-Héroult process uses the sodium impurity in alumina. Analysis options include: raw material types (magnesite rock vs. brine or seawater), drying and calcining using electricity vs. natural gas, and carbon vs. SOM anode type. Using SOM inert anodes results in a cost premium around 10%–15%, mostly due to higher electrical energy usage resulting from membrane resistance, and reduces GHG emissions by approximately 1 kg CO₂/kg Mg product. Capital and operating cost estimates, and cradle to gate greenhouse gas (GHG) emissions analysis under several raw material and process technology scenarios, show comparable costs and emissions to those of aluminum production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of chloride ingress on self-healing recovery of smart cementitious composite incorporating crystalline admixture and MgO expansive agent

Highlights: • Crack closure under wet/dry cycles in chloride solution is higher than the one in distilled water. • Element analysis shows that calcium is vital for crack healing either in water or chloride solution. • AFm is consumed by chloride ion to form Fs, and Fs were decomposed to AH{sub 3} by carbonation. • Soluble reactive silica reacts with calcium hydrate to form C-S-H gel to heal concrete cracks. • Expansion of magnesium hydroxide facilitates crack self-healing by interconnected network. In this study, the effect of chloride environment containing various concentrations of chloride ion (Cl{sup −}) on self-healing performance of pre-cracked cementitious composite containing crystalline admixture (CA) and MgO expansive agent (MEA) was investigated under wet-dry cycles in chloride solutions. The results revealed that the Cl{sup −} changed the mineralogy of self-healing products, and consequently, affected the crack closure ratio and mechanical strength recovery. When self-healing occurred in distilled water, a large amount of ettringite (AFt) were detected, whereas in Cl{sup −} solution, monosulfate (AFm) was consumed by Cl{sup −} to form Friedel's salt (Fs), and then the Fs was decomposed to Al(OH){sub 3}(AH{sub 3}) due to carbonation. During the multiphase conversion process, hydroxide (OH{sup −}) was released into crack solution, therefore the dissolved carbon dioxide (CO{sub 2}) concentration was increased. The carbonation of the crystals formed in cracks was accelerated with the volume expansion, which achieved rapid crack sealing but contributed little to the mechanical performance recovery.

36 MATERIALS SCIENCE↗

Enhanced activity and stability of MgO-promoted Ni/Al 2 O 3 catalyst for dry reforming of methane: Role of MgO

Highly dispersed nickel nanoparticles (NPs) were deposited on Al 2 O 3 NPs by atomic layer deposition (ALD). Various amounts of MgO were loaded on Ni/Al 2 O 3 catalysts by the incipient wetness (IW) method for dry reforming of methane. Fresh and used catalysts were systematically characterized to reveal the effects of MgO on the catalytic performance. MgO was found to increase the basic amount and basic strength of catalyst surfaces, which provided additional surface oxygen species and assisted the adsorption and activation of CO 2 . Although the formation of NiO-MgO solid solution, during the calcination of incipient wetness, did not improve the overall reducibility, the Ni NPs from NiO-MgO solid solution after reduction formed an intimate interaction with MgO, which could inhibit Ni NPs from sintering and provide sufficient metal-support interface for CO 2 activation. The MgO-promoted Ni/Al 2 O 3 reached a methane reforming rate of 1780 L CH4 g Ni -1 h -1 at 850 °C, which is 26% more than that of the pristine Ni/Al 2 O 3 . Finally, the higher CO 2 activity enhanced the oxidation rate of the surface carbon generated from side-reactions, thereby resulting in a higher reforming rate and inhibiting coke formation, especially the detrimental graphitic encapsulating carbon on the active nickel surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diamondlike carbon films as protective coatings for superconducting YBa2Cu3O7 films

We have investigated the use of diamondlike carbon (DLC) films for protecting superconducting YBCO films against degradation from exposure to moisture and acid. YBCO thin films on single crystal LaAlO3 and MgO substrates were deposited by laser ablation followed by DLC encapsulation. DLC films were deposited at pressures ranging from high vacuum to 0.1 Torr He. Substrate temperature was varied from 20 to 100 C during the deposition of DLC. The process compatibility of laser ablation was found convenient to sequentially deposit YBCO and DLC films from high purity stoichiometric targets. Epitaxial YBCO films on (100)LaAlO3 and (100)MgO substrates showed identical superconducting transitions before and after encapsulation by a DLC layer. The encapsulated films showed no degradation due to acid treatment or aging over a period of 45 days.

Ganapathi, L.↗

Post-Landing Major Element Quantification Using SuperCam Laser Induced Breakdown Spectroscopy

The SuperCam instrument on the PerseveranceMars 2020 rover uses a pulsed 1064 nm laser to ablate targets at a distance and conduct laser induced breakdown spectroscopy (LIBS) by analyzing the light from the resulting plasma. SuperCam LIBS spectra are preprocessed to remove ambient light, noise, and the continuum signal present in LIBS observations. Prior to quantification, spectra are masked to remove noisier spectrometer regions andspectra are normalized to minimize signal fluctuations and effectsof target distance.In some cases, the spectra are also standardized or binned prior to quantification. To determine quantitative elemental compositionsof diverse geologic materials at Jezero crater, Mars, we use a suite of 1198 laboratory spectra of 334 well-characterized reference samples. The samples were selected to span a wide range of compositions and include typical silicate rocks, pure minerals (e.g.,silicates, sulfates, carbonates, oxides),more unusual compositions (e.g.,Mn oreand sodalite), andreplicates of the sintered SuperCam calibration targets (SCCTs) onboardthe rover. For each major element (SiO2, TiO2, Al2O3, FeOT, MgO, CaO, Na2O, K2O), the database was subdivided into five“folds” with similar distributions of the element of interest. One fold was held out as an independent test set, and the remaining fourfolds were used to optimize multivariate regression models relating the spectrum to the composition. We considered a variety of models, and selected several for further investigation for each element, based primarily on the root mean squared error of prediction (RMSEP) on the test set, when analyzed at 3m. In cases with several models of comparable performance at 3 m, we incorporated the SCCT performance at different distances to choose the preferred model. Shortly after landing on Mars and collecting initial spectra of geologic targets, we selected one model per element. Subsequently, with additional data from geologic targets, some models were revised to ensure results that are more consistent with geochemical constraints. The calibration discussed here is a snapshot of an ongoing effort to deliver the most accurate chemical compositions with SuperCam LIBS.

Mars 2020↗

Life Cycle Assessment of Methanol from Fossil, Biomass, and Waste Sources, and Its Use as a Marine Fuel in Dual-Fuel Engines

Methanol is gaining interest in the marine sector from energy security and reducing emissions perspective. This study provides a comparative life cycle assessment of methanol as a marine fuel, across GHG and criteria air pollutant emission metrics, when it is used in a dual-fuel engine. Twelve methanol pathways from four different feedstock categories were considered, including (1) cellulosic biomass forest residues and clean pine mix, corn stover, switchgrass, and miscanthus; (2) organic wastes renewable natural gas from wastewater sludge, swine manure, food waste, and landfill gas; (3) fossil resources coal and natural gas (NG); and (4) e-methanol using captured carbon dioxide. When used in a dual-fuel engine with pilot fuel, life cycle GHG emissions for woody biomass-based methanol were approximately 19 gCO 2 e MJ −1 , while emissions from waste-based sources ranged between −154 and 31 gCO 2 e MJ −1 . Methanol from renewable sources showed a GHG reduction potential between 58 and 226% compared to conventional NG-based methanol (122 gCO 2 e MJ −1 ), primarily due to the avoided emissions from conventional waste management. When carbon from process emissions were captured, the reduction could be up to 327%. All pathways exhibited lower NO X , and particulate matter emissions compared to the baseline marine fuel (MGO 0.1% sulfur), while woody biomass and coal pathways had higher SO X emissions.

09 BIOMASS FUELS↗

A deep insight on the coal ash-to-slag transformation behavior during the entrained flow gasification process

Recent research provided deep insight on the coal ash-to-slag transformation characterization during the entrained flow gasification process, with experimentation on a 40 kg/hr (dry basis) coal-fed opposed multi-burner (OMB) entrained flow gasifier and simulation via FactSage™ software. A general mechanism is presented to relate the gasifier design temperature, ash fluid temperature, and operating temperature with the degree of the slag polymerization. The change of the high temperature zone, the corresponding particle residence time in the high temperature zone, and syngas composition have obvious effects on the slag mineral transformation behavior. Mineral types formed on the wall of the gasifier chamber were mainly anorthite (CaAl 2 Si 2 O 8 ), aluminum oxide (Al 2 O 3 ), and calcium sulfide (CaS). These minerals transformed to anorthite and diopside (CaMgSi 2 O 6 ) at the slag hole zone, while the minerals at the lock hopper were anorthite, orthoclase (KAlSi 3 O 8 ), quartz (SiO 2 ), gypsum (CaSO 4 ), calcite (CaCO 3 ), and halite (NaCl). FactSage™ predicted minerals as anorthite, diopside, orthoclase, and albite (NaAlSi 3 O 8 ), etc., where the slag temperature was below the ash fluid temperature and when the ratios of CO/CO 2 and (CO + H 2 )/CO 2 were lower than 1.0 and 2.0, respectively. By simulation, residual carbon was found to be the dominant factor over syngas composition to cause mineral transformation, and this was verified experimentally. The Ca-based crystals, typically anorthite, was shifted to diopside, near the slag hole zone, and a linear relationship was found between the content ratios of diopside/(anorthite + diopside), CaO/SiO 2 , and (CaO + MgO)/SiO 2 . A dimensionless number, θ, was defined to characterize the changing chemical composition and the degree of slag polymerization, with temperature deviation from the design condition. Three zones of θ were identified and related to the deviation between the actual gasification condition from the design condition. Finally, a low slag polymerization degree corresponded with a higher temperature deviation between the actual condition and design condition, and this proved that increased residual carbon content and changing iron valence state increased the mineral types when the slag temperature was below the ash fluid temperature.

01 COAL, LIGNITE, AND PEAT↗

Post-landing major element quantification using SuperCam laser induced breakdown spectroscopy

The SuperCam instrument on the Perseverance Mars 2020 rover uses a pulsed 1064 nm laser to ablate targets at a distance and conduct laser induced breakdown spectroscopy (LIBS) by analyzing the light from the resulting plasma. SuperCam LIBS spectra are preprocessed to remove ambient light, noise, and the continuum signal present in LIBS observations. Prior to quantification, spectra are masked to remove noisier spectrometer regions and spectra are normalized to minimize signal fluctuations and effects of target distance. In some cases, the spectra are also standardized or binned prior to quantification. To determine quantitative elemental compositions of diverse geologic materials at Jezero crater, Mars, we use a suite of 1198 laboratory spectra of 334 well-characterized reference samples. The samples were selected to span a wide range of compositions and include typical silicate rocks, pure minerals (e.g., silicates, sulfates, carbonates, oxides), more unusual compositions (e.g., Mn ore and sodalite), and replicates of the sintered SuperCam calibration targets (SCCTs) onboard the rover. For each major element (SiO 2 , TiO 2 , Al 2 O 3 , FeO T , MgO, CaO, Na 2 O, K 2 O), the database was subdivided into five “folds” with similar distributions of the element of interest. One fold was held out as an independent test set, and the remaining four folds were used to optimize multivariate regression models relating the spectrum to the composition. We considered a variety of models, and selected several for further investigation for each element, based primarily on the root mean squared error of prediction (RMSEP) on the test set, when analyzed at 3 m. In cases with several models of comparable performance at 3 m, we incorporated the SCCT performance at different distances to choose the preferred model. Shortly after landing on Mars and collecting initial spectra of geologic targets, we selected one model per element. Subsequently, with additional data from geologic targets, some models were revised to ensure results that are more consistent with geochemical constraints. The calibration discussed here is a snapshot of an ongoing effort to deliver the most accurate chemical compositions with SuperCam LIBS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-catalytic active site biochar-based catalysts for glucose isomerized to fructose: Experiments and density functional theory study

In this study, this work provides an innovative method for preparing different isomerization catalysts by impregnating different proportions of MgCl 2 and AlCl 3 and combining different K compounds on cellulose-derived biochar, followed by pyrolysis. Results show MgO and Al(OH) 3 existing in 4 Mg- 1 Al-C catalyst can obtain better catalytic effect on glucose isomerization than the singe of Al presenting in 0 Mg- 1 Al-C catalyst. Moreover, the synergism effects of the multi-catalytic active sites such as β-, γ -Al(OH) 3 , KCl, MgO, and K 4 H 2 (CO 3 ) 3 in Mg-Al-KHCO 3 -C catalyst can further lead to an increase in glucose isomerization, compared to the 4 Mg- 1 Al-C catalyst. The X-ray diffraction results present that the value of O/Al in Mg-Al-KHCO 3 -C catalyst is as high as 13.38, which provides many unsaturated acidic catalysis sites and benefits the glucose isomerization. Simultaneously, the TPD results reveal that the main active sites (MgO, Al(OH) 3 , and K 4 H 2 (CO 3 ) 3 ) in Mg-Al-KHCO 3 -C catalyst can provide weakly acidic and basic sites and avoid strongly acidic and basic sites to excessively attack the glucose. Based on the DFT analysis, the results indicate that the MgO has a great effect on the ring-opening reaction to form acyclic glucose, while Al(OH) 3+ has a great effect on promoting acyclic glucose hydrogen transfer isomerized to form fructose. Compared to other carbon-based metal catalysts, the prepared Mg-Al-KHCO 3 -C has excellent catalytic performance, which gives a higher fructose yield (38.7%) and selectivity (87.72%) and glucose conversion (44.12%) at 100 °C in 30 min. In this study, we develop a highly efficient Mg-Al-K-biochar catalyst for glucose isomerization and provide an efficient method for cellulose valorization.

36 MATERIALS SCIENCE↗

Geochemical-hydromechanical couplings during water-serpentinized harzburgite interactions at 20° C and 30 bars

Interaction of groundwater with the serpentinized harzburgites of the upper mantle plays an important role in the geologic carbon cycle and serpentinization processes. Here, in this study, an intact serpentinized harzburgite with more than 60% lizardite from the Semail ophiolite in Oman was reacted with water at near neutral pH and low PCO 2 to observe its dissolution behavior and reaction path within the CaO-MgO-SiO 2 -CO 2 -H 2 O system at 20 °C and 30 bars. In the experiment, mass (i.e. H 2 O, ions) transfer is by diffusion and the selected temperature and pressure conditions mimic water-rock interactions at the shallow portions of most ultramafic rock hosted aquifers. Equilibrium activity-activity diagrams and thermodynamic data were used to compare the experimentally determined reaction path with the theoretical stability boundaries for minerals involved to investigate the evolution of bulk chemical composition, mineralogy, and water composition. The experiments demonstrated that (i) the water-rock interactions increased the pH of the aqueous phase from 5.9 to 7.5 over a period of 18 weeks; (ii) the dissolution of lizardite, orthopyroxene (enstatite), and clinopyroxene (diopside and augite) increased the concentration of Mg, Ca, and Si in the aqueous phase; (iii) the dissolution was incongruent with respect to Mg and Si, favoring Si release at pH > 6 due to (a) breaking of more reactive cation‑oxygen bonds that is consistent with the stoichiometry of magnesium for proton exchange reaction which favors a surface that is enriched in Mg at basic conditions, and (b) preferential dissolution of clinopyroxene Mg 1.30 Ca 0.52 Fe 0.06 Si 2 O 6 ; (iv) the aqueous phase was undersaturated with respect to carbonate (e.g. calcite, magnesite, and hydromagnesite) and hydrous (e.g. lizardite, chrysotile, brucite, and talc) minerals; (v) the bulk chemical composition and mineralogy of the intact serpentinized harzburgite matrix did not change; (vi) the thermodynamic data can successfully predict water-intact serpentinized harzburgite behavior if the water chemical composition can be constrained; and (vii) no detectable macroscopic form of damage (e.g. microcracks forming as a result of differential stress fields due to changes in volume during chemical reaction) was observed.

Carbonation↗

Effect of surface acidity modulation on Pt/Al 2 O 3 single atom catalyst for carbon monoxide oxidation and methanol decomposition

With ideal metal utilization efficiency and homogeneous active sites, single atom catalysts (SACs) have attracted extensive attention in heterogeneous catalysis field. The performance of SACs is highly dependent on the local coordination environment of metal single atoms. However, few works reported the effect of surface acidity modification on the performance of SACs such as Pt SACs which have been widely studied nowadays. In this work, a Pt/Al 2 O 3 SAC has been successfully prepared using a bayerite Al(OH) 3 as support through simple IWI method for Pt loading. Through post-modification of Pt/Al 2 O 3 with acidic WO 3 and basic MgO, the surface acidity of Pt/Al 2 O 3 was tuned. Here, activity of CO oxidation and methanol decomposition on the modified catalysts has been evaluated. It was found that the catalytic performance was highly related to the surface acidity of Pt SACs. Basic MgO modified Pt/Al 2 O 3 performed better in CO oxidation under the reaction condition with H 2 O. Acidic WO 3 modified Pt/Al 2 O 3 showed superior activity in methanol decomposition. Detailed characterization and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) study suggested that the positive H 2 O effect on CO oxidation was due to the mitigated formation of bicarbonate species on Pt/Al 2 O 3 and WO 3 /Pt/Al 2 O 3 catalysts and the promoted desorption of carbonate species from MgO/Pt/Al 2 O 3 . The superior methanol decomposition performance on WO 3 /Pt/Al 2 O 3 was owing to its abundant oxygen vacancies and high resistance to carbonate accumulation. This study highlights the importance of surface acidity modulation of Pt SACs in heterogeneous catalysis and suggests that fine-tuning the surface acidity can be an effective strategy in new SACs development.

36 MATERIALS SCIENCE↗

Corrosion Issues for Ceramics in Gas Turbines

The requirements for hot-gas-path materials in gas turbine engines are demanding. These materials must maintain high strength and creep resistance in a particularly aggressive environment. A typical gas turbine environment involves high temperatures, rapid gas flow rates, high pressures, and a complex mixture of aggressive gases. Figure 26.1 illustrates the requirements for components of an aircraft engine and critical issues [1]. Currently, heat engines are constructed of metal alloys, which meet these requirements within strict temperature limits. In order to extend these temperature limits, ceramic materials have been considered as potential engine materials, due to their high melting points and stability at high temperatures. These materials include oxides, carbides, borides, and nitrides. Interest in using these materials in engines appears to have begun in the 1940s with BeO-based porcelains [2]. During the 1950s, the efforts shifted to cermets. These were carbide-based materials intended to exploit the best properties of metals and ceramics. During the 1960s and 1970s, the silicon-based ceramics silicon carbide (SiC) and silicon nitride (Si3N4) were extensively developed. Although the desirable high-temperature properties of SiC and Si3N4 had long been known, consolidation of powders into component-sized bodies required the development of a series of specialized processing routes [3]. For SiC, the major consolidation routes are reaction bonding, hot-pressing, and sintering. The use of boron and carbon as additives which enable sintering was a particularly noteworthy advance [4]. For Si3N4 the major consolidation routes are reaction bonding and hot pressing [5]. Reaction-bonding involves nitridation of silicon powder. Hot pressing involves addition of various refractory oxides, such as magnesia (MgO), alumina (Al2O3), and yttria (y2O3). Variations on these processes include a number of routes including Hot Isostatic Pressing (HIP), gas-pressure sintering, sinter-HIPing, and Encapsulation-HIPing. It is important to note that each process involves the addition of secondary elements, which later were shown to dramatically influence oxidation and corrosion behavior. As dense bodies of silicon-based ceramics became more readily available, their desirable high temperature properties were confirmed. These materials retained strength to very high temperatures (i.e. 1300-1400 C). Further, they were lightweight and made from abundant materials. SiC and Si3N4 therefore emerged as leading ceramic candidates for components in heat engines, designed to operate at higher temperatures for better performance and fuel efficiency. The first US programs for ceramics in heat engines have been reviewed [6]. Selected programs on ceramic engine parts are summarized here in regard to their contributions to understanding the corrosion behavior of a heat engine environment.

Jacobson, Nathan S.↗