Search NASA⌕ Search

SEARCH · Search NASA

Results for “chemical etching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Influence of Surface Treatment on the Interfacial and Mechanical Performance of Metal-Insert Overmolded Composites

Structural composites with metal inserts are gaining increasing interest enabling light weight design for energy efficiency, provide insulation, corrosion protection without compromising mechanical integrity. Such over molded metal-polymer composites show strong potential in many automotive and aerospace component parts, e.g. car bumper, chassis, door, brackets, fasteners, etc. Despite several advantages, metal-polymer dissimilar interface remains a weak spot in structural design, requiring further investigation to improve interfacial interlocking. The current work focuses on enhancing the metal-polymer adhesion between stainless steel inserts and polymer matrices (e.g. acrylonitrile butadiene styrene resin (ABS), and polyamide 66 (PA66) through surface treatment via chemical etching and mechanical roughening. In the chemical etching process, metal substrates were treated with aqua regia solution for different time intervals to evaluate surface roughness measured by water contact angle and morphology analysis. For mechanical roughening approach, metal inserts were subjected to blasting for surface abrasion. Treated samples were also functionalized with aminosilane coupling agent which showed successful grafting on the surface measured by water contact angle. Metal inserts with micro level surface roughness through etching exhibited significant 21% improvement in adhesion strength compared to untreated inserts; however, the effect of silane treatment on the interfacial strength was found to be highly matrix dependent.

Saha, Subhabrata [ORNL] (ORCID:000000033966064X)↗
DOE OSTI2020

Microscopic Observation of Solid Electrolyte Interphase Bilayer Inversion on Silicon Oxide

Silicon has been investigated in recent years as an alloying anode material to enhance gravimetric energy density in lithium-ion batteries. Although recent developments have suggested that silicon oxides exhibit improved cycling stability over pure Si, the origin of the improved cycling performance is still poorly understood. The initial solid electrolyte interphase (SEI) formation mechanisms on Si wafers with both native oxide and chemically etched thermal oxide coatings are investigated structurally, chemically, and morphologically in the nanoscale. After one electrochemical cycle, microscopy reveals that SEI formed on native SiO x features the typical SEI bilayer structure with a carbon-rich outer SEI layer and an inorganic-rich inner SEI layer. In contrast, the SEI formed on chemically etched thermal oxide shows an inversion in the structure. This work observes distinct initial SEI formation mechanisms on the HF-etched SiO 2 surface, which may be partially responsible for improved cycle life observed in SiO x -based anode materials.

25 ENERGY STORAGE↗
NASA NTRS1991

Evaluation of Surlyn 8920 as PHE Visor Material and Evaluations of New Adhesives for Improving Bonding Between Teflon and Stainless Steel at Cryogenic Temperature

Two studies are presented, and in the first study, Surlyn 8920 (an ionic and amorphous low density polyethylene made by Dupont) was evaluated as a possible replacement of Plexyglass G as PHE visor material. Four formulations of the polymer were made by adding different amounts of UV stabilizer, energy quencher, and antioxident in a Brabender Plasticorder. The formulated polymers were molded in the form of sheets in a compression molder. Cut samples from the molded sheets were exposed in a weatherometer and tested on Instron Tensile Tester for strength and elongation. Specially molded samples of the formulated polymers were subjected to Charpy Impact Tests. In the second study, preliminary evaluations of adhesives for improvement of bonding between Teflon and stainless steel (SS) were performed. Kapton, a high temperature polyimide made by Dupont, and a rubber based adhesive made by Potter Paint Co., were evaluated against industrial quality epoxy, the current material used to bond Teflon and SS. The degreased surfaces of the SS discs were etched mechanically, with a few of these etched chemically. The surfaces of the SS discs were etched mechanically, with a few of these etched chemically. Bonding strengths were evaluated using lap shear tests on the Instron Tensile Tester for the samples bonded by Kapton and industrial quality epoxy. Bond strengths were also evaluated using a pull test on the Instron for the samples bonded by Potter adhesive (CWL-152) and industrial quality epoxy. Based on limited lap shear data, Kapton gave bond strength favorable compared to that of industrial epoxy. Based on limited pull test data, Kapton bonded and CWL-152 bonded samples showed poor strength compared to epoxy bonded sample.

Ray, Asit K.↗
NASA NTRS1979

Local atomic and electronic structure of oxide/GaAs and SiO2/Si interfaces using high-resolution XPS

The chemical structures of thin SiO2 films, thin native oxides of GaAs (20-30 A), and the respective oxide-semiconductor interfaces, have been investigated using high-resolution X-ray photoelectron spectroscopy. Depth profiles of these structures have been obtained using argon ion bombardment and wet chemical etching techniques. The chemical destruction induced by the ion profiling method is shown by direct comparison of these methods for identical samples. Fourier transform data-reduction methods based on linear prediction with maximum entropy constraints are used to analyze the discrete structure in oxides and substrates. This discrete structure is interpreted by means of a structure-induced charge-transfer model.

Grunthaner, F. J.↗
DOE OSTI2023

Unraveling Anisotropic and Pulsating Etching of ZnO Nanorods in Hydrochloric Acid via Correlative Electron Microscopy

Despite much technical progress achieved so far, the exact surface and shape evolution during wet chemical etching is less unraveled, especially in ionically bonded ceramics. Herein, by using in situ liquid cell transmission electron microscopy, a repeated two-stage anisotropic and pulsating periodic etching dynamic is discovered during the pencil shape evolution of a single crystal ZnO nanorod in aqueous hydrochloric acid. Specifically, the nanopencil tip shrinks at a slower rate along [0001̅] than that along the $\langle$101̅0$\rangle$ directions, resulting in a sharper ZnO pencil tip. Afterward, rapid tip dissolution happens due to accelerated etching rates along various crystal directions. Concurrently, the vicinal base region of the original nanopencil tip emerges as a new tip followed by the repeated sequence of tip shrinking and removal. The high-index surfaces, such as {101̅m} (m = 0, 1, 2, or 3) and {21̅1̅n} (n = 0, 1, 2, or 3), are found to preferentially expose in different ratios. Our 3D electron tomography, convergent beam electron diffraction, middle-angle bright-field STEM, and XPS results indicate the dissociative Cl – species were bound to the Zn-terminated tip surfaces. Furthermore, DFT calculation suggests the preferential Cl – passivation over the {101̅1} and (0001) surfaces of lower energy than others, leading to preferential surface exposures and the oscillatory variation of different facet etching rates. The boosted reactivity due to high-index nanoscale surface exposures is confirmed by comparatively enhanced chemical sensing and CO 2 hydrogenation activity. In conclusion, these findings provide an in-depth understanding of anisotropic wet chemical etching of ionic nanocrystals and offer a design strategy for advanced functional materials.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Seamless metal-clad fiber-reinforced organic matrix composite structures and process for their manufacture

A metallic outer sleeve is provided which is capable of enveloping a hollow metallic inner member having continuous reinforcing fibers attached to the distal end thereof. The inner member is then introduced into outer sleeve until inner member is completely enveloped by outer sleeve. A liquid matrix member is then injected into space between inner member and outer sleeve. A pressurized heat transfer medium is flowed through the inside of inner member, thereby forming a fiber reinforced matrix composite material. The wall thicknesses of both inner member and outer sleeve are then reduced to the appropriate size by chemical etching, to adjust the thermal expansion coefficient of the metal-clad composite structure to the desired value. thereby forming a fiber reinforced matrix composite material. The wall thicknesses of both inner member and outer sleeve are then reduced to the appropriate size by chemical etching, to adjust the thermal expansion coefficient of the metal-clad composite structure to the desired value. The novelty of this invention resides in the development of a efficient method of producing seamless metal clad fiber reinforced organic matrix composite structures.

Bluck, Raymond M.↗
NASA NTRS2015

Solar Flare Track Exposure Ages in Regolith Particles: A Calibration for Transmission Electron Microscope Measurements

Mineral grains in lunar and asteroidal regolith samples provide a unique record of their interaction with the space environment. Space weathering effects result from multiple processes including: exposure to the solar wind, which results in ion damage and implantation effects that are preserved in the rims of grains (typically the outermost 100 nm); cosmic ray and solar flare activity, which result in track formation; and impact processes that result in the accumulation of vapor-deposited elements, impact melts and adhering grains on particle surfaces. Determining the rate at which these effects accumulate in the grains during their space exposure is critical to studies of the surface evolution of airless bodies. Solar flare energetic particles (mainly Fe-group nuclei) have a penetration depth of a few millimeters and leave a trail of ionization damage in insulating materials that is readily observable by transmission electron microscope (TEM) imaging. The density of solar flare particle tracks is used to infer the length of time an object was at or near the regolith surface (i.e., its exposure age). Track measurements by TEM methods are routine, yet track production rate calibrations have only been determined using chemical etching techniques [e.g., 1, and references therein]. We used focused ion beam-scanning electron microscope (FIB-SEM) sample preparation techniques combined with TEM imaging to determine the track density/exposure age relations for lunar rock 64455. The 64455 sample was used earlier by [2] to determine a track production rate by chemical etching of tracks in anorthite. Here, we show that combined FIB/TEM techniques provide a more accurate determination of a track production rate and also allow us to extend the calibration to solar flare tracks in olivine.

Berger, Eve L.↗
DOE OSTI2020

Rapid Patterning and Advanced Device Structures for Low Cost Manufacturable Crystalline Si IBC Cells

Recent record efficiency Si cells have had an interdigitated back contact (IBC) design where both positive and negative contacts are fabricated on the back side of the Si wafer. Many industry groups have investigated IBC cells but used photolithography to pattern the rear contacts although it is considered impractical for low cost, high volume manufacturing. Alternative patterning methods using lasers and mechanical masking have been utilized in fabrication of patterned regions in IBC Si solar cells to replace photolithography. Another exciting advance in Si solar cell technology has been replacing the high temperature diffusion of doped regions inside the crystalline Si wafer with low temperature deposition of very thin layers of doped amorphous hydrogenated Si (a-Si:H) on the Si wafer. This is called a Si heterojunction (HJ) device. The a-Si:H provides excellent passivation of surface defects and has produced the highest open circuit voltages (VOC) of any Si solar cell device structure. The Institute of Energy Conversion (IEC) demonstrated the first IBC-HJ solar cell combining these two strategies in 2007 and has fabricated IBC-HJ cells with 20% efficiency using three photolithography steps. Despite the demonstrated efficiency potential of this device by industry groups (>26%) there is no commercial production because of the challenges of patterning and processing the structure in an industrial environment. Our work sought to address that challenge. The objective of this 3 year project was to develop the processing for the IBC-HJ Si solar cell using lasers for patterning and contact formation instead of photolithography. Laser patterning enables rapid, contactless manufacturing of patterned regions. We intensively studied laser fired contacts, laser patterning of the a-Si multi-layer stacks and metal layers and the use of plasma shadow masks. After an exhaustive focus in the first year on the laser fired emitter (LFE) and contact (LFC), we were unable to achieve VOC greater than 660 mV, compared to the 720 mV required to meet our milestones. We discovered that an additional issue with our original IBC structure was the presence of an inversion layer at the back surface connecting the p and n regions which reduced the VOC and fill factor (FF). We developed innovative methods for characterizing the inversion layer. These two limitations in the original design lead to development of a new IBC-HJ process sequence and device structure which we called Plasma Masked Laser Processed (PMLP). It retained the original high efficiency features including manufacturability. The LFC was replaced with a standard n-type a-Si HJ contact. The inversion layer was eliminated by replacing the previous p-type stack in the gap with an n-type or SiN stack. The PMLP used laser ablation of a multi-layer a-Si stack followed by chemical etching to open the n-contact. It required deposition of a patterned stack through a mask in the plasma deposition chamber. This turned out to be a source of significant problems due to inevitable unwanted deposition ‘leakage’ under the mask. This formed a blocking contact on the emitter which significantly reduced Voc and FF. Several iterations in PMLP device structure and chemical etching steps resulted in a large improvements, e.g. the efficiency increasing from 3 to 15% and Voc from 450 to 660 mV but they were unable to completely eliminate it. The best IBC-HJ device we fabricated had only 15% efficiency. For perspective, our standard FHJ devices had 20% efficiency.

14 SOLAR ENERGY↗
NASA NTRS1977

Residual stresses in boron/tungsten and boron/carbon fibers

By measuring the change in fracture stress of 203 micrometer diameter fibers of boron on tungsten (B/W) as a function of fiber diameter as reduced by chemical etching, it is shown that the flaws which limit B/W fiber strength are located at the surface and in the tungsten boride core. After etching to a diameter of 188 micrometers m virtually all fiber fractures were caused by core flaws, the average strength being 4.50 GN/sq m. If both the surface and core flaws are removed, the fracture strength, limited by flaws in the boron itself, is approximately 6.89 GN/sq m. This was measured on B/W fibers which were split longitudinally and had their cores removed by chemical etching. The longitudinal residual stress distribution was determined for 102 micrometer diameter B/W and B/C fibers.

Behrendt, D. R.↗
DOE OSTI2025

Performance improvement of proton exchange membrane water electrolysis by surface modification of porous transport layers

Proton exchange membrane water electrolysis (PEMWE) is a promising option for hydrogen production from a variety of energy sources. Cost-effective production of hydrogen with PEMWE requires reduction of costly precious metals as well as optimization of the components and interfaces in the cell. The interface between the platinum-coated titanium porous transport layer (PTL) and catalyst layer (CL) significantly impacts the performance of the electrolyzer cell. Here, we report on two PTL modification methods, mechanical abrasion and chemical etching, which we find improve PEMWE performance by lowering the resistance of the PTL/CL interface. The PTL surface modifications enabled performance improvements up to 77 mV at 4 A cm −2 and reduction of the high frequency resistance, demonstrating that the resistance of the PTL/CL interface is a significant factor in the cell performance. The PTL surface roughness was varied using abrasive materials ranging from 0.1 to 140 μm in grain sizes and chemical etching was found to also increase the surface roughness. The surface roughness was quantified using confocal laser microscopy and the surface oxidation was measured using X-ray photoemission spectroscopy. These results demonstrate that both increasing surface roughness and oxide removal contribute to lowering the PTL/CL interfacial resistance and increasing cell performance.

08 HYDROGEN↗
NASA NTRS2016

Modified Surface Having Low Adhesion Properties to Mitigate Insect Residue Adhesion

A process to modify a surface to provide reduced adhesion surface properties to mitigate insect residue adhesion. The surface may include the surface of an article including an aircraft, an automobile, a marine vessel, all-terrain vehicle, wind turbine, helmet, etc. The process includes topographically and chemically modifying the surface by applying a coating comprising a particulate matter, or by applying a coating and also topographically modifying the surface by various methods, including but not limited to, lithographic patterning, laser ablation and chemical etching, physical vapor phase deposition, chemical vapor phase deposition, crystal growth, electrochemical deposition, spin casting, and film casting.

Wohl, Christopher J., Jr.↗
NASA NTRS1981

XPS study of interface formation of CVD SiO2 on InSb

The interfacial chemistry of CVD SiO2 films deposited on thin native oxides grown on InSb substrates is examined using X-ray photoemission spectroscopy (XPS) and a relatively benign chemical etching technique for depth profiling. An intensity analysis of XPS spectra is used to derive the compositional structure of the interfaces obtained in the SiO2/native oxide/InSb system. Peak positions in these spectra are used to follow the change in substrate surface potential during the etch sequence, and to establish the chemical nature of the species formed during deposition and subsequent processing. Reaction of the substrate with oxygen resulted in an In-rich native oxide and 1-2 monolayers of excess elemental Sb at the native-oxide/substrate interface, incompletely oxidized silane reduced the native oxide, leaving less than 1 monolayer of elemental In at the SiO2/native oxide interface. Etch removal of this thin In-rich layer leads to a change in the substrate surface potential of 0.06 eV, corresponding to a net increase in positive charge. The results are consistent with simple thermodynamic considerations; they are also compared to previously reported studies of deposited dielectrics on III-V compound semiconductors.

Vasquez, R. P.↗
DOE OSTI2023

Loss Analysis and Performance Optimization Pathways of 729-mV VocSi Solar Cells with Poly-Si on Locally-Etched Dielectric Passivating Contacts

In this article, the performance analysis of a 22.5% efficient polysilicon on silicon oxide (poly-Si/SiOx) passivated contact solar cells with deliberately introduced pinholes using metal-assisted chemical etching (MACE) has been performed with the help of optical analysis using Sunsolve and electrical analysis using Quokka3. The power loss is maximum due to recombination and resistive losses in the bulk (~0.76 mW/cm2 ) followed by power loss due to rear contact recombination (~0.35 mW/cm2 ). Recombination at the front surface also contributes to 0.24 mW/cm2. The effect of improving the bulk lifetime and lowering the recombination current density at the rear side on Voc, FF and efficiency has been investigated.

MACE↗
DOE OSTI2022

Geranium Photodiodes for Hard Xray Detection

This report summarizes the investigations engaged at UC Davis under subcontract B632083, as related to the LLNL-LDRD Project “High-Speed X-Ray Imager Arrays.” The first section entails work done within the Electrical and Computer Engineering (ECE) Department. The purpose of the work done so far is to understand photodiode design and which parameters are conducive to the design goals, which are: I: Maximize the detector quantum efficiency. The device must have a quantum efficiency of roughly 5% at 80 keV. II: Minimize temporal response. Collection time is limited to 1ns. All charge must be collected in that time. III: Minimize dark current. In this document, various photodiode parameters and designs are explored, and their impact on these goals are tabulated. In addition to these, various instruments that have been constructed for either testing these parameters or helping teammates with their experiments. The second section entails work done with the Materials Science Engineering (MSE) Department. In accordance with the proposed development of the germanium ROIC backside imagers, a critical step in the micromachining of these devices was the removal of the substrate on which the PIN junctions were epitaxially grown. A common technique for the micromachining of silicon wafers is the use of chemical etching alongside an “etch-stop” layer. In this technique, a chemical etchant will remove material until it reaches the etch-stop layer, at which the etch rate will drop significantly. This high selectivity (ratio of etch rates) allows any unevenness in the initial etching to be effectively smoothed away in the event that part of the wafer surface reaches the etch-stop layer sooner than another. An initial literature review found a paper by Divan et al. in which the authors used ion implantation to dope germanium wafers and achieve selectivity on the order of 100, sufficient for a reliable etch-stop.

42 ENGINEERING↗