Search NASA⌕ Search

SEARCH · Search NASA

Results for “compositional data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗
DOE OSTI2025

Expansion of the Direct Feed High-Level Waste Glass Composition in the High Al Range

Baseline glass compositions have been developed and demonstrated for successful immobilization of Hanford high-level waste (HLW) prepared through a pretreatment process. Recent enhanced waste glass formulations have shown promise to increase the waste loading of pretreated sludge compositions from a broader range of HLW feeds. This project proposes to increase the loading of minimally pretreated Hanford HLW in glass by expanding the existing database and glass property-composition models. Estimated direct-feed high level waste (DFHLW) compositions were generated by the Hanford Tank Operations Contractor and used by Pacific Northwest National Laboratory to determine target glass compositions. Gaps in existing data were identified including one high-priority gap in the high Al compositional region. This report summarizes the data collected during the characterization of the DFHLW High Al Glass Matrix. These glasses were intentionally designed with high aluminum concentrations (15 to 30 wt%) and a high likelihood of nepheline formation, which is known to negatively affect glass durability. Some glasses were expected to either fail or approach property constraints to fill data gaps in poorly understood regions of the compositional space due to lack of data. Out of the 50 glasses tested, 14 glasses formed nepheline, while the model predicted nepheline formation in 20 glasses. All quenched glasses met the product consistency test durability constraint; however, 8 glasses failed this constraint after undergoing the canister centerline cooling treatment. Additionally, 17 glasses did not meet the viscosity constraints, 4 failed the EC constraints, and 2 exceeded the allowable T2% for spinel crystal formation. All glasses satisfied the SO 3 solubility limit. The resulting dataset provides valuable information to improve model accuracy and reduce prediction uncertainty. These insights will ultimately support the development of more robust glass formulation strategies, enabling higher waste loadings, reducing operational risks, and expanding the processing envelope.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Transferable predictions of energetic and structural properties for refractory solid solution alloys across chemical compositions

We present a data-efficient approach to train graph neural networks (GNNs) on density functional theory (DFT) data for accurate and transferable predictions of energetic and structural properties of refractory solid solution alloys in the niobium-tantalum-vanadium (Nb-Ta-V) chemical space. We start by training the GNN model only on DFT data that describes refractory binary alloys niobium-tantalum (Nb-Ta), niobium-vanadium (Nb-V), and tantalum-vanadium (Ta-V) to predict formation enthalpy and root mean squared displacement. Once trained, the GNN predictions are tested on DFT data describing refractory ternary alloys Nb-Ta-V. While, unsurprisingly, direct transferability from binary to ternary is not sufficiently accurate, augmenting the training with only 1% of the available ternary data (uniformly distributed across the entire range of chemical compositions) improves significantly the quality of the GNN predictions. For comparison, we assess the transferability in the opposite direction by training GNN models on ternary Nb-Ta-V data and making predictions on binaries Nb-Ta, Nb-V, and Ta-V, which exhibits notably higher predictive errors. The proposed methodology, which favors transferability from lower-component to higher-component alloys, offers an efficient path towards avoiding the curse of dimensionality incurred when collecting DFT data for discovery and design of multi-component disordered alloys.

Density functional theory calculations↗
DOE OSTI2025

Improving commercial truck fleet composition in emission modeling using 2021 US VIUS data

Commercial trucks are essential elements of the nation's supply chain system. Meanwhile, intensive truck movements contribute significantly to system externalities, such as energy use and air pollution. However, collecting detailed fleet composition and distribution of operational patterns remains a barrier to accurately accounting for these impacts. The recently released 2021 US Vehicle Inventory and Use Survey (US VIUS) fills a critical gap in understanding commercial truck fleet distributions, their operations, and business constraints at the national scale. This study aims to understand the latest US commercial vehicle fleet composition and operational characteristics using 2021 US VIUS data and calibrate the fleet inputs in regulatory emission models to assess the potential emission implications of the VIUS-derived fleet composition. The emission rates for commercial trucks and default fleet composition are collected from the U.S. EPA's MOtor Vehicle Emission Simulator (MOVES4). The 2021 US VIUS data is applied to improve fleet characteristics such as the long-haul fraction and the vehicle mileage accumulation rate. The study also investigates potential emission reduction benefits under various forecasted fleet electrification scenarios. The energy consumption and critical air pollutant rates by vehicle types are compared between MOVES4 and US VIUS fleets for both current and future scenarios to provide insights into the latest U.S. commercial vehicle fleet characteristics and their implications on energy and emissions. This study helps policymakers and practitioners advance the commercial fleet generation for emission models. It also deepens the understanding of the emission reduction potential of the commercial fleet under various fleet projections.

2021 US VIUS↗
DOE OSTI2024

BSEC Air Quality: Stationary Aerosol Composition and Mass Concentration at Baltimore

Data is 10-min average mass composition and mass concentration from the TOF-ACSM-X and Aethalometer AE33. TOF-ACSM-X reports fine (less than 2.5 um diameter) non-refractory aerosol, including organic aerosol, sulfate, nitrate, ammonium, and non-refractory chloride. Aethalometer measured the attenuation at different wavelengths for aerosol collected onto tape; one wavelength is used to convert to black carbon mass concentration. Also reported is the elemental ratios determined for organic aerosol (O/C, H/C, and organic matter to organic carbon ratio, OM/OC).

aerosol↗
DOE OSTI2025

BSEC Air Quality: Stationary Aerosol Composition and Mass Concentration at Baltimore

Data is 10-min average mass composition and mass concentration from the TOF-ACSM-X. TOF-ACSM-X reports fine (less than 2.5 um diameter) non-refractory aerosol, including organic aerosol, sulfate, nitrate, ammonium, and non-refractory chloride. Also reported is the elemental ratios determined for organic aerosol (O/C, H/C, and organic matter to organic carbon ratio, OM/OC). Finally, ion ratios of key ions used for identifying sources, ammonium balance, and fractional contribution of organic nitrate aerosol to total aerosol nitrate has been included.

aerosol↗
DOE OSTI2025

Rapid data acquisition and machine learning-assisted composition design of functionally graded alloys via wire arc additive manufacturing

Abstract The lack of high-quality datasets in materials science hinders artificial intelligence (AI)-driven alloy design. To address this challenge, wire arc additive manufacturing (WAAM) was employed to fabricate graded alloys, generating extensive data for machine learning (ML)-assisted property prediction. ML models were developed using high-throughput experiments, computational models, and genetic algorithm to optimize feature selection, successfully predicting hardness and porosity. The ML model demonstrated its efficacy by designing a gradient alloy with enhanced properties. However, scaling up revealed uncertainties in tensile property and porosity due to differences in size and thermal conditions between the designed alloy build and the gradient print used to construct the ML model. This underscores the need for uncertainty quantification and process optimization in WAAM-driven alloy design. Our work advances AI-integrated additive manufacturing, offering a rapid approach to exploring process–structure–property relationships and accelerating materials development.

Wang, Xin↗
DOE OSTI2025

“CY1” Chondrites Produced by Impact Dehydration of the CI Chondrite Parent Body

The recently proposed Yamato-type (CY) chondrites share significant similarities with CI chondrites and Ryugu. We present major and trace elemental, Re–Os, and mass-independent Ti, Cr, and Fe isotope data for seven CY chondrites. The elemental data along with isotopic compositions reveal two distinct lithologies, here designated as CY1 and CY2, potentially originating from two different parent bodies. Although sharing similarities with CM chondrites, CY2 chondrites have distinct Cr isotope compositions, arguing against a close genetic relationship. The CY1 lithology exhibits elemental abundances similar to CI chondrites/Ryugu as well as Fe, Ti, and Cr isotope compositions that closely overlap with those of CI chondrites/Ryugu. This suggests that CI chondrites, CY1 chondrites, and Ryugu accreted in the same region of the solar system and may even originate from the same parent body. In fact, we find that the reduced water content and certain volatile element abundances alongside increased sulfide content and mass-dependent O isotope enrichments observed in CY1 compared to CI chondrites could be attributed to an impact-induced heating event on the CI parent body. This impact likely disrupted the CI parent body, resulting in the ejection of both CI and CY1 lithologies. Furthermore, given that there are presently only five known CI meteorite specimens, the close chemical composition between CY1 and CI chondrites substantially expands the data set for comparisons and referrals to the bulk solar system composition for nonvolatile elements. Finally, we propose that the “CY1” chondrites could be called “CI1T,” while the designation “CY” chondrites could be restricted to “CY2” samples.

Zhu, Ke 朱柯 [China University of Geosciences (Wuhan↗
DOE OSTI2026

Plutonium migration and phase evolution in irradiated U-Pu-Zr metallic fuels: An integrated EPMA-SEM-TEM study

Constituent redistribution is a defining feature of irradiated U-Pu-Zr metallic fuels, yet its mechanisms and effects on fuel performance are not sufficiently resolved to guide model development. Although decades of irradiation testing have established broad trends, a true mechanistic understanding of constituent redistribution has not been achieved. Here, in this study, we use electron probe microanalysis (EPMA), scanning electron microscopy (SEM), and transmission electron microscopy-based (TEM) selective area electron diffraction (SAED) on a EBR-II irradiated U-19 wt.% Pu-6 wt.% Zr fuel pin cross-section to correlate the composition, porosity, and crystallographic phases formed after irradiation. Constituent redistribution is thought to consist of three distinct zones, in which uranium and zirconium migrate while plutonium remains relatively unchanged. Our EPMA results resolve eight distinct compositional regions, and more importantly, show that plutonium redistributes alongside zirconium, contrary to historical assumptions. The distribution of fission products was highly asymmetric with a few large lanthanide precipitates observed at isolated sites on the pin periphery instead of a uniform distribution of smaller precipitates around the periphery. Using thermodynamic data from TAF-ID and the measured EPMA compositions, matrix phase fractions were predicted across the fuel radius. Phase predictions based on composition did not match TEM/SAED results, which revealed a much higher fraction of α−U phase than would be expected if phases were retained from reactor temperatures. These findings highlight the need for expanded SAED phase identification to capture post-irradiation and storage effects, as well as rigorous uncertainty quantification in fuel performance and phase diagram modeling to better constrain predictions from compositional data.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Direct Feed High-Level Waste APPS Model Glass Testing (DFHLW APPS) Matrix, Phase 2

This report summarizes the data collected during the batching and melting of a second matrix of Direct Feed High-Level Waste (DFHLW) glasses generated using the preliminary enhanced waste glass models (EWG2.5) and the Britton and Anderson (2024) preliminary DFHLW feed vector. The purpose of these glasses is two-fold: 1. Validate EWG2.5 glass calculations being used in the Aspen Process Performance Simulation (APPS) model. 2. Evaluate and ultimately improve the glass property models and formulation methods used for design of DFHLW glasses as part of an iterative process of data collection and model refinement. Some of the 16 APPS2 glasses tested did not satisfy all target property constraints due to the limited data on DFHLW glass supporting the EWG2.5 models. • One glass, APPS2-10, formed nepheline on canister centerline cooling (CCC) heat-treatment and failed the product consistency test (PCT) response limits. This glass also had high B and Cr release rates for the toxicity characteristic leaching procedure (TCLP). All other glasses were found to satisfy the PCT and TCLP constraints for both quenched and CCC samples. • One glass, APPS2-08, had higher than acceptable viscosity due to magnetite crystallization. • One glass, APPS2-09, formed greater than 2 vol% crystals at 950 °C. As the glass design criterion was that the temperature at 2 vol% crystal (T 2% ) be less than 950 °C, only one glass failed the criteria. However, this criterion is being reevaluated. Four additional glasses formed crystal fractions between 1 and 2 vol% at 950 °C (APPS2-03, -08, -12, and -14). • Four glasses – APPS2-01, -02, -04, and -16 – failed the Monofrax K-3 refractory neck corrosion (k neck ) design limit of 0.04 in. at 1208 °C for 6 d. This is another criterion being reevaluated. Four additional glasses (APPS2-05, -06, -11, and -13) exhibited 0.025 = k neck = 0.04 in. • All 16 glasses passed the sulfur solubility and TCLP constraints. The measured property values were compared to predicted values using EWG2.5 and a selection of other existing models. A few models (e.g., electrical conductivity, TCLP) were found to be adequate for designing DFHLW glasses in the near future, while others require refits or offsets. It is recommended that new property models be developed for EWG3.0, as a large amount of DFHLW glass property data (> 14 × existing data) is expected to be collected in the compositional spaces where no data was previously available. To enable near-term calculations and formulations for designing DFHLW glasses and processing rate estimations, a formulation algorithm with minor modifications will be developed, EWG2.6.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Enhanced HLW Glass Property-Composition Models – Phase 2

As a continuation of the Phase 1 HLW model development work as part of a phased approach to enhance and expand HLW glass property-composition models, additional data were collected for the HLW glass dataset and used to revise the models developed during Phase 1. These data are for glasses that are collectively referred to as ORP-2014 glasses. The sources of additional data for the Phase 2 work included: (i) actively designed glasses formulated to support various glass studies at VSL since the completion of Phase 1; and (ii) glasses from two statistically designed matrices to supplement the existing HLW compositional space. The Phase 2 matrix design was intended to augment and improve the coverage in the high aluminum region.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Systematic characterization of unknown compounds via dimensionality reduction of time series

Analysis of ambient aerosols provides valuable insight into particle sources and formation chemistry. However, due to the complexity of atmospheric data and the dynamic nature of aerosol composition, a substantial fraction of data often become discarded by conventional analysis methods. Furthermore, a large fraction of chemical species within those data are unidentifiable due to a lack of matching spectral information, resulting in suboptimal characterization of chemical composition. Previous work has demonstrated techniques for cataloging analytes in a chromatographic dataset by deconvolution of mass spectra, but integration of these analytes throughout a large dataset remains time consuming. Here, we present a method to automatically identify an ion for quantitation for single-ion chromatogram based peak fitting and integration, enabling comprehensive integration of analytes with minimal user interaction. The resulting time series are clustered with a machine-learning based dimensionality reduction technique to systematically investigate the underlying characteristics of the categorized analytes and gain new insights into the chemical composition and physicochemical properties of the unidentifiable analytes. We apply these methods to existing atmospheric datasets collected in Manacapuru, Brazil during the GoAmazon2014/5 campaign to identify new analytes and interpret their variability and transformations in the atmosphere. The analysis results generate 408 time series from cataloged analytes of interest, and the clustering of those time series with spherical k-means results in 8 distinct clusters. We find the analytes form clusters based on their distinct physicochemical properties, demonstrating the method’s ability to systematically identify and selectively filter contaminants and instrumental analytes and characterize the unidentifiable analytes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

High-throughput micro-scale bandgap mapping for perovskite-inspired materials with complex composition space

Abstract To realize the full promise of high-throughput experimental workflows, the rate of sample synthesis must be matched by that of characterization. Of growing interest are contactless optical techniques that can rapidly measure material homogeneity and properties. Here, we present a hyperspectral imaging method to measure local optical bandgap distributions within samples, utilizing spatially-resolved reflectance spectra coupled with automated data analysis. We collect approximately one million optical bandgap data across the compositional space of Cs 3 (Bi x Sb 1-x ) 2 (Br y I 1-y ) 9 perovskite-inspired materials. Our results show non-monotonic bandgap variations (i.e., bandgap bowing) along six composition gradient sequences, in addition to identifying samples with multiple bandgaps in statistics. High-throughput transient absorption spectroscopy reveals that within these compositions, the depletion of the ground state carriers to excited states occurred at discrete energy levels with independent carrier dynamics, consistent with the bandgap observation and indicative of phase separation. This work demonstrates the potential for rapid optical measurements to assess material quality and homogeneity in a high-throughput experimental setting, supporting screening and recipe optimization of optoelectronic material candidates with desired carrier dynamics and optical properties.

Science & Technology - Other Topics↗
DOE OSTI2025

NEWTS Economic Data Dashboard: Critical Materials for Energy

The NEWTS Economic Data Dashboard: Critical Materials for Energy is an economic screening tool for assessing the concentration and potential value of the 18 critical materials for energy in fossil energy-related wastewater across the United States. Datasets used to develop the dashboard and complete economic calculations are available as supplementary downloads. These resources were developed primarily using geochemical composition and volume data from the NEWTS Integrated dataset (version 1.0). Energy-related wastewater types presented in the dashboard include produced water (PW), brackish groundwater (BW), acid mine drainage (AMD), coal combustion residual leachate (CCRL), power plant flue gas desulfurization wastewater (FGD), and geothermal fluids. The concentrations of the following critical minerals were included in the analysis, when available: Al, Co, Cu, Dy, F, Ga, Ge, C, Ir, Li, Mg, Mn, Nd, Ni, Pt, Pr, Si, Tb. This economic screening tool was built to support identification of promising critical mineral feedstocks and economic research targets.

Critical Minerals; Critical Minerals and Materials↗
DOE OSTI2025

Bench-Scale Apparatus for Rapid, Simultaneous, Comprehensive Vapor–Liquid Equilibrium and Kinetic Property Measurements to Advance CO 2 Capture Solvent Technology

We present here, the design, fabrication, and testing of a new "pressure, volume, temperature (PVT)" apparatus that enables rapid standardized testing for viscosity, vapor–liquid equilibria, and kinetics for water-lean carbon capture solvents. This unit is the first of its kind where equilibrium data are collected during operation as a PTx (pressure–temperature–composition) cell while kinetic data are collected simultaneously with an internal mini wetted-wall contactor (WWC) using controlled adjustments of CO 2 injections to allow for measurements of gas flux (in and out of the liquid). Additionally, in situ measurements of viscosity data are also continuously collected while a solvent is in circulation during gas absorption. This cell empowers comprehensive testing of critical CO 2 capture solvent properties in a single measurement, ensuring all data are collected at the same temperature, pressure, and CO 2 loading. This apparatus also expedites screening of materials since less than 50 mL of sample is needed as compared to 2–3 L needed to get similar data from a conventional WWC. In conclusion, we describe here the methodology of data collected on this new PVT cell, nicknamed “Gary” in honor of Professor Gary Rochelle, for multiple water-lean amine solvents, which we compare to data collected from conventional instrumentation for amine testing.

Zheng, Richard [STARS Technology Corporation, Rich↗
DOE OSTI2025

Multimuons in cosmic-ray events as seen in ALICE at the LHC

ALICE is a large experiment at the CERN Large Hadron Collider. Located 52 meters underground, its detectors are suitable to measure muons produced by cosmic-ray interactions in the atmosphere. In this paper, the studies of the cosmic muons registered by ALICE during Run 2 (2015–2018) are described. The analysis is limited to multimuon events defined as events with more than four detected muons (N μ > 4) and in the zenith angle range 0° < θ < 50°. The results are compared with Monte Carlo simulations using three of the main hadronic interaction models describing the air shower development in the atmosphere: QGSJET-II-04, EPOS-LHC, and SIBYLL 2.3d. The interval of the primary cosmic-ray energy involved in the measured muon multiplicity distribution is about 4 × 10 15 < E prim < 6 × 10 16 eV. In this interval none of the three models is able to describe precisely the trend of the composition of cosmic rays as the energy increases. However, QGSJET-II-04 is found to be the only model capable of reproducing reasonably well the muon multiplicity distribution, assuming a heavy composition of the primary cosmic rays over the whole energy range, while SIBYLL 2.3d and EPOS-LHC underpredict the number of muons in a large interval of multiplicity by more than 20% and 30%, respectively. The rate of high muon multiplicity events (N μ > 100) obtained with QGSJET-II-04 and SIBYLL 2.3d is compatible with the data, while EPOS-LHC produces a significantly lower rate (55% of the measured rate). For both QGSJET-II-04 and SIBYLL 2.3d, the rate is close to the data when the composition is assumed to be dominated by heavy elements, an outcome compatible with the average energy E prim ∼ 10 17 eV of these events. This result places significant constraints on more exotic production mechanisms.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Leveraging machine learning to enhance aerosol classification using Single-Particle Mass Spectrometry

Advancing automated classification of atmospheric aerosols from Single-Particle Mass Spectrometry (SPMS) data remains challenging due to overlapping ion signatures, compositional diversity, and limited labeled data. This study evaluates supervised and semi-supervised learning frameworks to enhance aerosol identification by jointly leveraging labeled and unlabeled spectra. Four models were compared: a supervised Support Vector Machine (SVM), a self-training SVM, a stacked autoencoder classifier, and a stacked autoencoder trained using a temporal-ensembling Mean Teacher approach. All models achieved high and stable accuracies (90.0 %–91.1 %), surpassing previous results on the same dataset (87 %) and matching the performance of state-of-the-art deep learning methods. Despite small global metric differences (≤ 1 %), semi-supervised variants yielded up to 5 %–10 % improvements for compositionally rare particle types – such as soot (0.77 % of spectra, F1-score: 0.93–0.97) and hazelnut pollen (0.98 % of spectra, F1-score: 0.97–1.00) – equating to roughly ∼ 187 additional correctly classified spectra. These gains are scientifically significant, as such rare particles exert disproportionate influence on radiative absorption and ice nucleation processes; their improved detection reduces modeled uncertainties in aerosol absorption optical depth and mixed-phase cloud ice nucleation rates. The models' residual misclassifications (≈ 9 %) largely arise from true spectral overlap among chemically adjacent species (e.g., Na- vs. K-feldspar, coated vs. uncoated feldspars), reflecting physical compositional continuity rather than algorithmic error. Collectively, these findings demonstrate that leveraging unlabeled data to learn robust spectral representations and refine classification enhances both fidelity and interpretability, bridging data-driven analysis with aerosol–climate process understanding.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Utah FORGE: Triaxial Direct Shear Results - February 2025

This dataset contains results from nine triaxial direct shear tests conducted by Los Alamos National Laboratory on samples from FORGE Well 16A(78)-32. The primary objectives of this work were to determine the shear strength in both intact and residual states, evaluate dilation against displacement, assess permeability in relation to displacement, time, and normal stress, understand the relationship between aperture and normal stress, and monitor the effluent chemistry as a function of time. The data includes time-series measurements of stress, displacement, permeability, and effluent chemistry, with and without experimental dilution corrections. Additional materials include profilometry data, photographic documentation of the experimental setups and apparatus, and test notes. The dataset is organized into folders corresponding to each test, containing hydromechanical data, effluent chemistry measurements, and images. The hydromechanical data consists of detailed time-series records capturing parameters such as shear force, confining pressure, permeability, and temperature. Effluent chemistry data tracks fluid composition changes over time. Also included are conference papers, presentation slides, and a summary document outlining the experiments.

15 GEOTHERMAL ENERGY↗