Search NASA⌕ Search

SEARCH · Search NASA

Results for “computational fluid dynamics simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Computational Fluid Dynamics Simulations of Glass Vitrification Refractory Coupon Tests

The Waste Treatment and Immobilization Plant (WTP) at the Hanford site is nearing the start of the Direct-Feed Low-Activity Waste (DFLAW) operations. DFLAW is destined to convert a pretreated low activity waste portion of the 56 million gallons of tank waste into a stable solid glass. In the subsequent decade completion of the high-level waste (HLW) facility is anticipated. Sustained operational missions of both LAW and HLW melter facilities are expected over multiple decades. In high-temperature glass melters, the refractory lining corrodes over time, which could potentially be an issue for longer term operations, this refractory corrosion is higher at the level of the glass-air interface due to surface tension driven flow. The glass viscosity, melt pool temperature, and glass chemical composition can impact the rate at which the refractory corrodes. This rate is important to quantify for the various waste glasses to be produced at the WTP since the integrity of the refractory should not be a limiting factor affecting the lifetime of the melter. To this end, a series of glasses representative of the first batches of waste glass produced by the WTP will be melted in small-scale crucibles with Monofrax® K-3 coupons inserted. The corrosion of the K-3 will be measured in the melt and at the meltline (or neckline). A model for the corrosion rate will be constructed and implemented into a previously developed framework for a computational fluid dynamics (CFD) model of the full-scale WTP. To assist with experimental design and validate the implementation of the model in the full-scale melter, CFD simulations of the small-scale crucible tests were performed. The bubbling that occurs in the small-scale crucible is initially validated here with a model that uses silicone oil at room temperature. The viscosity of the oil ranges from 1 to 100 Pa•s, which corresponds to operating glass pool temperatures near 1150 °C down to idling temperatures near 950 °C. The simulation results show good agreement with the bubble sizes that form during experiments. CFD modeling of the crucible setup was used to determine bubbling characteristics to match the range of near-wall velocities expected in the full-scale WTP. This study presents the initial CFD modeling results, corrosion testing plan, and some preliminary corrosion samples with an outline for the next steps for the development of the corrosion model.

Abboud, Alexander W. [Idaho National Lab]↗

Incorporating Oxygen Uncoupling Kinetics into Computational Fluid Dynamic Simulations of a Chemical Looping System

Chemical looping with oxygen uncoupling (CLOU) is a carbon-capture technology that utilizes a metal oxide as an oxygen carrier to separate oxygen from air and releases gaseous O 2 into a reactor where fuel is fed. Earlier experimental and simulated work has been performed on systems less than 1 MW. Previous work has been limited to one-dimensional kinetic simulations. Literature kinetics were modified to work in a Barracuda-VR simulation package. A simplified spreadsheet model was used to verify the Barracuda-VR simulation adaption of the kinetics to previously published results. The simulated kinetics, literature models, and raw data matched well. The adapted kinetics were then incorporated into a 10 kW dual bubbling bed CLOU system three-dimensional simulation. The simulations predicted carbon capture efficiency similar to that reported previously for similar systems. The solid circulation rate, temperature profile, and gas concentration profiles followed the expected trends. The overall three-dimensional simulation of kinetics showed reasonable results for what has been previously reported.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

3D probabilistic fracture mechanics / computational fluid dynamics simulation of a reactor pressure vessel under transient conditions

Reactor pressure vessels (RPVs) are safety-critical light-water-reactor components that, under irradiation, experience long-term material degradation in the form of embrittlement. This can increase their susceptibility to fracture under thermal-shock conditions, which could occur during off-normal transients such as loss-of-coolant accidents (LOCAs). During a LOCA, the most severe conditions for the RPV occur when emergency core cooling water is injected through the cold legs into the water-and-steam-filled RPV. The rapid cooling of the downcomer and internal RPV surface causes decreased temperature and elevated thermally driven tensile stresses in the RPV wall. This, combined with long-term material embrittlement, may cause fracture initiation at pre-existing flaws, challenging the integrity of the RPV. Assessing RPV integrity during transients with a large spatial variation in the coolant temperature requires a modeling approach that considers the effects of spatially varying coolant temperature on the fracture probability of a population of flaws distributed throughout the RPV, accounting for spatially varying embrittlement. Here, the present study addresses this need by demonstrating first-of-its-kind coupling of a high-fidelity 3D computational fluid dynamics code with 3D probabilistic fracture mechanics This was accomplished using representative models of a pressurized-water reactor subjected to small- and medium-break LOCA conditions, both of which can result in large spatial temperature variations. While the observed impact of accounting for 3D effects was minimal under the small-break LOCA this study indicates a significant increase in the probability of fracture initiation under the medium-break LOCA when 3D effects are considered, relative to a spatially uniform cooling scenario.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

Computational Fluid Dynamics Simulations to Support Efficiency Improvements in Aluminum Smelting Process

Smelting is broadly described as the extraction of a metal from its ore. In the United States, aluminum is commonly produced by smelting alumina in bauxite using the Hall-Héroult process. Optimization of equipment and processes in conventional smelting is crucial to enhancing process efficiency and productivity, is necessary for improving the techno-economic feasibility, which directly manifests as the growth of the American economy. To achieve optima, insightful data on the multiphysics phenomena that are inherent to the process must be obtained through physical investigation or high-fidelity numerical simulations. The resolution of relevant scales in time and space for smelting operations requires intensive, high-performance computing (HPC) simulations. Hostile operating conditions limit physical data acquisition to specific techniques; therefore, these data do not describe the multiscale interaction of simultaneous effects. Fortunately, in recent decades, significant advancements in computing hardware and computational methods have made the numerical resolution of such a complex process possible. In this study, a high-fidelity simulation of aluminum smelting was performed using an open-source tool, OpenFOAM, which analyzed many parameters characteristic to underlying phenomena. A multiphysics model based on the Eulerian-Eulerian multifluid approach was adopted. This model can resolve critical issues in the electrolytic smelting of aluminum, such as bubbling of carbon dioxide from the anode(s), magnetohydrodynamics from electromagnetic effects, ionic dissolution of the alumina in the electrolyte, and the evolution of thermal profiles. This study provides valuable connectivity for characteristic data that can direct the future designs of efficient smelters. A basic framework to model and simulate the smelting process using OpenFOAM is presented for user modification in keeping with process development. Of relevance to the flow field, a detailed investigation of vortices produced by bubble motion and electromagnetics is discussed, along with their impact on the evolution of thermal profiles. The predictions show small-scale vortices in the clearance between the anode and cathode caused by magnetic forces. Predictions also indicate relatively large-scale vortices in the inter-anode space resulting from carbon dioxide rising through the electrolytic flow field. The formation of vortices at the edges of anodes was shown to direct alumina charged by the feeder to the bottom of the anodes, thus preventing the entrapment of gas bubbles in the periphery of the bottom of the anode. Symmetry was observed in the location of cold spots in the electrolytic mixture in the vicinity of the feeder. Cold spots were also observed in the clearance between the anode and cathode due to the flow’s transmission of unconverted alumina to this region.

36 MATERIALS SCIENCE↗

A dissipation-based method for improving the accuracy of computational fluid dynamics simulations of high level non-Newtonian wastes

Here this paper investigates a new viscosity model for laminar, transitional, and turbulent pipe flow simulations of a non-Newtonian slurry using the Star-CCM+ software. Herschel-Bulkley (HB) rheology equation was used in its original and modified forms to model the fluid viscosity. The realizable k-ε model was used for modeling of turbulence. It was observed that simulations using the HB model predicted inaccurate profiles of U (mean velocity) and U + (mean velocity in wall units). Therefore, we developed alternative values of viscosity obtained directly from non-linearity of stress–strain variation (α) in each iteration. The developed method, “Alpha method”, applied changes in places where dissipation rate of turbulent kinetic energy occurred and was designed based on local or global dissipation rate values. Inverse values of α were used to test effects of more viscosity reduction for all flow regimes. In prediction of the mean velocities, significant improvements were obtained through global adjustment of viscosity in inverse form during simulation of the laminar and turbulent flow cases. For the transitional flow, obtaining improvements in prediction of U and U + from the same model version faced challenges. While the global adjustments in direct form were found significantly effective in improving the prediction of U, they failed to predict the U + accurately. For this purpose, Local viscosity adjustments were found significantly effective.

42 ENGINEERING↗

Energy Exascale Computational Fluid Dynamics Simulations With the Spectral Element Method

Development and application of the open-source GPU-based fluid-thermal simulation code, NekRS, are described. Time advancement is based on an efficient kth-order accurate timesplit formulation coupled with scalable iterative solvers. Spatial discretization is based on the high-order spectral element method (SEM), which affords the use of fast, low-memory, matrix-free operator evaluation. Further, recent developments include support for nonconforming meshes using overset grids and for GPU-based Lagrangian particle tracking. Results of large-eddy simulations of atmospheric boundary layers for wind-energy applications as well as extensive nuclear energy applications are presented.

42 ENGINEERING↗

Computational Fluid Dynamics Simulation of Lignocellulosic Biomass Transport in a Compression-Screw Feeder

There is continued interest in lignocellulosic biomass feedstocks for producing power, heat, and transportation liquid fuels in order to increase energy diversification and security. However, there are a few problems associated with the biomass production that must be resolved before biorefineries are considered economical. One of these problematic operations is the process of feeding biomass to reactor systems. Compression-screw feeders have been widely used as a way to fulfill this purpose. However, due to variability of feedstock properties and its complex challenges, production plants operate at less than 50% of their design capacity due to process upsets along with mechanical wear and failure. The objective of this study is to numerically investigate the screw-feeder operation and performance for various biomass physical properties and under different operating conditions. Therefore, the findings from this study will reduce the number of physical experiments needed to improve the plant design.

09 BIOMASS FUELS↗

Computational Fluid Dynamics Simulation of Compressible Non-Newtonian Biomass in a Compression-Screw Feeder

Compression-screw feeders play a critical role in biorefineries to transport lignocellulosic biomass feedstocks from the feeding hoppers to biomass-conversion reactors in order to pretreat and convert biomass to hydrocarbon liquid biofuels and other power and energy resources. One of the main challenges in the operation of screw feeder is plugging and jamming of compressed biomass with high concentration of insoluble solids. The focus of this paper is to numerically investigate the screw feeder at these challenging operating conditions and help with the optimization of the screw feeder design to avoid operation failure. In this work a customized CFD model based on open-source OpenFOAM package [1] was developed to simulate the concentrated biomass as a highly viscous non-Newtonian fluid in the screw feeder. The biomass is modeled as a single-phase compressible Bingham fluid with a plastic viscosity as well as a density-dependent yield stress. The compressibility formulation (pressure-dependent density) and the density-dependent yield stress formulation in the governing equations follow the suggestions from a recent study by Duncan et al. [2]. A pilot-scale hopper/screw feeding system at NREL [3] is used to compare the experimental observations with our simulation results. The auger is 280 mm long and tapered with outer diameter changing from 80 mm to 35 mm. The auger rotates from 10 to 60 rpm in a conical throat which contains anti-rotational bars. The simulations predicted the required torque for the screw feeder and the pressure increase at the exit for biomass feedstocks with various fluid viscosity properties and auger rotating speeds. The analysis of the stress forces helped to identify the critical conditions were the screw feeder excessive wear or jamming could occur.

biofuels↗

A Dissipation-Based Method for Improving the Accuracy of Computational Fluid Dynamics Simulations of High Level Non-Newtonian Waste - 17351

Analysis of shear rate in dissipative scales of turbulence was performed using a quasi-direct numerical simulation (Q-DNS) of flow through a pipe involving Bingham fluid. Dependency of deformation rate on dissipative scales of turbulence was studied and a modification algorithm was developed and implemented in Reynolds-averaged Navier-Stokes (RANS) modeling of the same flow using the standard k-e model. It was shown that the modification was effective in increasing accuracy of the RANS simulations when the velocity profile was modified to match experimental data. In both the Q-DNS and RANS simulations, the Herschel-Bulkley (HB) rheology equation was used to relate shear stress of the non-Newtonian fluid to shear deformation. Additional analysis of dependency of shear on the turbulent dissipation rate (TDR) was performed using various flow conditions in RANS simulations with a modified viscosity model (alpha model). In the past, the alpha model has been shown to produce accurate simulations for the same flow conditions. Results of the analysis shows that a qualitative agreement exists between shear dependency in the RANS-alpha and Q-DNS-HB simulations when the ratio of velocity to length scale is used. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Memory access optimization for particle operations in computational fluid dynamics-discrete element method simulations

Computational Fluid Dynamics - Discrete Element Method is used to model gas-solid systems in several applications in energy, pharmaceutical and petrochemical industries. Computational performance bottlenecks often limit the problem sizes that can be simulated at industrial scale. The data structures used to store several millions of particles in such large-scale simulations have a large memory footprint that does not fit into the processor cache hierarchies on current high-performance-computing platforms, leading to reduced computational performance. This paper specifically addresses this aspect of memory access bottlenecks in industrial scale simulations. The use of space-filling curves to improve memory access patterns is described and their impact on computational performance is quantified in both shared and distributed memory parallelization paradigms. The Morton space filling curve applied to uniform grids and k-dimensional tree partitions are used to reorder the particle data-structure thus improving spatial and temporal locality in memory. The performance impact of these techniques when applied to two benchmark problems, namely the homogeneous-cooling-system and a fluidized-bed, are presented. We report these optimization techniques lead to approximately two-fold performance improvement in particle focused operations such as neighbor-list creation and data-exchange, with ~ 1.5 times overall improvement in a fluidization simulation with 1.27 million particles.

97 MATHEMATICS AND COMPUTING↗

Machine learning accelerated turbulence modeling of transient flashing jets

We report modeling the sudden depressurization of superheated liquids through nozzles is a challenge because the pressure drop causes rapid flash boiling of the liquid. The resulting jet usually demonstrates a wide range of structures, including ligaments and droplets, due to both mechanical and thermodynamic effects. As the simulation comprises increasingly numerous phenomena, the computational cost begins to increase. One way to moderate the additional cost is to use machine learning surrogacy for specific elements of the calculation. This study presents a machine learning-assisted computational fluid dynamics approach for simulating the atomization of flashing liquids accounting for distinct stages, from primary atomization to secondary breakup to small droplets using the Σ - Y model coupled with the homogeneous relaxation model. Notably, the models for thermodynamic non-equilibrium (HRM) and Σ - Y are coupled, for the first time, with a deep neural network that simulates the turbulence quantities, which are then used in the prediction of superheated liquid jet atomization. The data-driven component of this method is used for turbulence modeling, avoiding the solution of the two-equation turbulence model typically used for Reynolds-averaged Navier-Stokes simulations for these problems. Both the accuracy and speed of the hybrid approach are evaluated, demonstrating adequate accuracy and at least 25% faster computational fluid dynamics simulations than the traditional approach. This acceleration suggests that perhaps additional components of the calculation could be replaced for even further benefit. Published under an exclusive license by AIP Publishing.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A method for data handling numerical results in parallel OpenFOAM simulations

Parallel computational fluid dynamics simulations produce vast amount of numerical result data. This paper introduces a method for reducing the size of the data by replaying the interprocessor traffic. The results are recovered only in certain regions of interest configured by the user. A known test case is used for several mesh partitioning scenarios using the OpenFOAM toolkit{sup ®}[1]. The space savings obtained with classic algorithms remain constant for more than 60 Gb of floating point data. Our method is most efficient on large simulation meshes and is much better suited for compressing large scale simulation results than the regular algorithms.

42 ENGINEERING↗

Scientific Data Compression for Large Scale Computational Fluid Dynamics (CFD) Simulations

This Cooperative Research and Development Agreement (CRADA) between Oak Ridge National Laboratory (ORNL) and General Electric (GE) investigated methods for reducing the size of large computational fluid dynamics (CFD) simulation datasets using scientific data compression techniques. The work focused on adapting the MultiGrid Adaptive Reduction of Data (MGARD) compression framework and integrating it with high-performance I/O and visualization tools used in CFD workflows. MGARD uses hierarchical multilevel decomposition to enable error-controlled compression of floating-point scientific data while preserving quantities of interest. During the project, MGARD compression was integrated with the ADIOS I/O framework and visualization tools such as ParaView to enable efficient storage, transfer, and analysis of simulation data. The collaboration also explored approaches for improving compression performance for CFD data defined on unstructured meshes. Results demonstrate that scientific data compression can significantly reduce storage requirements and improve data management for large-scale CFD simulations.

97 MATHEMATICS AND COMPUTING↗

Magnetic resonance imaging and computational fluid dynamics (CFD) simulations of rabbit nasal airflows for the development of hybrid CFD/PBPK models

The percentages of total airflows over the nasal respiratory and olfactory epithelium of female rabbits were calculated from computational fluid dynamics (CFD) simulations of steady-state inhalation. These airflows calculations, along with nasal airway geometry determinations, are critical parameters for hybrid CFD/physiologically based pharmacokinetic models that describe the nasal dosimetry of water-soluble or reactive gases and vapors in rabbits. CFD simulations were based upon three-dimensional computational meshes derived from magnetic resonance images of three adult female New Zealand White (NZW) rabbits. In the anterior portion of the nose, the maxillary turbinates of rabbits are considerably more complex than comparable regions in rats, mice, monkeys, or humans. This leads to a greater surface area to volume ratio in this region and thus the potential for increased extraction of water soluble or reactive gases and vapors in the anterior portion of the nose compared to many other species. Although there was considerable interanimal variability in the fine structures of the nasal turbinates and airflows in the anterior portions of the nose, there was remarkable consistency between rabbits in the percentage of total inspired airflows that reached the ethmoid turbinate region (~50%) that is presumably lined with olfactory epithelium. These latter results (airflows reaching the ethmoid turbinate region) were higher than previous published estimates for the male F344 rat (19%) and human (7%). These differences in regional airflows can have significant implications in interspecies extrapolations of nasal dosimetry.

59 BASIC BIOLOGICAL SCIENCES↗