SEARCH · Search NASA

Results for “conditional approach”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Experimental quiet engine program. Predicted engine performance

Three turbofan configurations, each incorporating alternative noise reduction features, were tested under the Quiet Engine Program. Performance data for these engines are shown over a range of flight conditions. The data are presented in tabular form for standard day flight inlet conditions. Procedures for estimating nonstandard day performance are shown. Tabular data and calculation procedures to allow determination of ram recovery, customer bleed, and customer shaft power extraction effects on engine performance can be found in the original Performance Brochure titled, Experimental Quiet Engine Program, Predicted Engine Performance, dated April 8, 1970. Predicted engine noise levels for representative take-off and approach conditions are provided.

Source record↗

NASA NTRS1992

Analysis of an advanced ducted propeller subsonic inlet

A time marching Navier-Stokes code called PARC (PARC2D for 2-D/axisymmetric and PARC3D for 3-D flow simulations) was validated for an advanced ducted propeller (ADP) subsonic inlet. The code validation for an advanced ducted propeller (ADP) subsonic inlet. The code validation was implemented for a non-separated flow condition associated with the inlet operating at angles-of-attack of 0 and 25 degrees. The inlet test data were obtained in the 9 x 15 ft Low Speed Wind Tunnel at NASA Lewis Research Center as part of a cooperative study with Pratt and Whitney. The experimental study focused on the ADP inlet performance for take-off and approach conditions. The inlet was tested at a free stream Mach number of 0.2, at angles-of-attack between O and 35 degrees, and at a maximum propeller speed of 12,000 RPM which induced a corrected air flow rate of about 46 lb/sec based on standard day conditions. The computational grid and flow boundary conditions (BC) were based on the actual inlet geometry and the funnel flow conditions. At the propeller face, two types of BC's were applied: a mass flow BC and a fixed flow properties BC. The fixed flow properties BC was based on a combination of data obtained from the experiment and calculations using a potential flow code. Comparison of the computational results with the test data indicates that the PARC code with the propeller face fixed flow properties BC provided a better prediction of the inlet surface static pressures than the predictions when the mass flow BC was used. For an angle-of-attack of 0 degrees, the PARC2D code with the propeller face mass flow BC provided a good prediction of inlet static pressures except in the region of high pressure gradient. With the propeller face fixed flow properties BC, the PARC2D code provided a good prediction of the inlet static pressures. For an angle-of-attack of 25 degrees with the mass flow BC, the PARC3D code predicted statis pressures which deviated significantly from the test data; however, with the fixed flow properties BC, a good comparison with the test data was obtained.

Iek, Chanthy↗

NASA NTRS1972

An experimental investigation of STOL longitudinal flying qualities in the landing approach using the variable stability X-22A aircraft.

The first in-flight flying qualities experiment using the variable stability X-22A aircraft investigated longitudinal flying qualities requirements for STOL aircraft in terminal area operations. Emphasis was placed on defining minimum requirements for the short-term response in VFR and IFR landing approaches at representative steep STOL approach conditions of 65 and 80 knots. Evaluation flights were conducted in negligible and moderate turbulence for a wide range of short-term frequencies and dampings. The results were compared with the short-term requirements of MIL-F-83300. The specified Level 1 and 2 VFR boundaries were found to be approximately valid in moderate turbulence for both VFR and IFR flight conditions. In negligible turbulence, the specified VFR Level 2 boundary was also approximately valid but the Level 1 boundary was found to be too stringent. Pilot rating gradients with damping were more apparent than with frequency for the range investigated.

Schuler, J. M.↗

NASA NTRS1973

Evaluation of glide paths for landing a VTOL airplane using linear regulator theory.

A method of evaluating certain characteristics of approach paths for VTOL airplanes is presented which is based on the solution of the matrix Riccati equation to obtain an optimal state variable feedback controller. The longitudinal equations of motion of the airplane are linearized about a preselected path and the resulting system of equations is treated as a linear, time-varying regulator. The controller which minimizes a quadratic cost function is applied to the linearized system to determine the airplane's ability to return to the prescribed path given a specified initial error in altitude. The procedure is applied to the XC-142A, tilt-wing, V/STOL airplane, under decelerating approach conditions with a glide path consisting of two segments, the first having a smaller angle of descent than the second.

Reid, G. F.↗

NASA NTRS1974

Gust alleviation for a STOL transport by using elevator, spoilers, and flaps

Control laws were developed to investigate methods of alleviating the response of a STOL transport to gusty air. The transport considered in the study had triple-slotted, externally blown jet flaps and a large T-tail. The control devices used were the elevator, spoilers, and flaps. A hybrid computing system was used to simulate linearized longitudinal dynamics of the aircraft and to implement a conjugate gradient optimal search algorithm. The aircraft was simulated in the low-speed approach condition only. Feedback control matrices were found which minimized the average of a quadratic functional involving passenger compartment accelerations, pitch angle and rate, flight path angle and speed variations. The optimization was performed for artificially designed gust inputs in the form of predetermined rectangular waveforms. Results were obtained for elevator, spoilers, and flaps acting singly and in combination. Additional results were obtained for unit sinusoidal gust inputs by using the gain matrices computed for the artificial test gusts. Various sensor configurations were also investigated.

Lallman, F. J.↗

NASA NTRS1974

The interaction between an impact-produced neutral gas cloud and the solar wind at the lunar surface

On Apr. 15, 1970, the Apollo 13 S-IVB stage impacted the nighttime lunar surface. Beginning 20 sec after impact, the Suprathermal Ion Detector Experiment and the Solar Wind Spectrometer observed a large flux of positive ions (maximum flux of about 3 x 10 to the 8th ions/sq cm/sec/ster) and electrons. Two separate streams of ions were observed: a horizontal flux that appeared to be deflected solar wind ions and a smaller vertical flux of predominantly heavy ions (greater than 10 amu), which probably were material vaporized from the S-IVB stage. An examination of the data shows that collisions between neutral molecules and hot electrons (50 eV) were probably an important ionization mechanism in the impact-produced neutral gas cloud. These electrons, which were detected by the Solar Wind Spectrometer, are thought to have been energized in a shock front or some form of intense interaction region between the cloud and the solar wind. Thus strong ionization and acceleration are seen under conditions approaching a collisionless state.

Lindeman, R. A.↗

NASA NTRS1974

Ionization equilibrium in soft X-ray-emitting solar flares

Studies of the 1.9-A line produced by highly ionized iron during a solar flare indicate that this emission occurs under conditions approaching a steady-state ionization equilibrium. Time-dependent and steady-state ionization equilibrium values are used for calculation of 1.9 A line fluxes per unit flare emission. The results are compared with those obtained by observations of some four solar flares, showing that the calculations from time-dependent equilibrium values approximate the observed line flux values with the same accuracy as the calculations from steady-state equilibrium values only when the electron densities are equal to or greater than 10 billion per cu cm.

Phillips, K. J. H.↗

NASA NTRS1973

Space shuttle orbit maneuvering engine reusable thrust chamber program

Tests were conducted on the regenerative cooled thrust chamber of the space shuttle orbit maneuvering engine. The conditions for the tests and the durations obtained are presented. The tests demonstrated thrust chamber operation over the nominal ranges of chamber pressure mixture ratio. Variations in auxiliary film coolant flowrate were also demonstrated. High pressure tests were conducted to demonstrate the thrust chamber operation at conditions approaching the design chamber pressure for the derivative space tug application.

Pauckert, R. P.↗

NASA NTRS1976

Single stage, low noise, advanced technology fan. Volume 5: Fan acoustics. Section 1: Results and analysis

The acoustic tests and data analysis for a 0.508-scale fan vehicle of a 111,300 newton (25,000 pound) thrust, full-size engine, which would have application on an advanced transport aircraft, is described. The single-stage advanced technology fan was designed to a pressure ratio of 1.8 at a tip speed of 503 m/sec (1,650 ft/sec) to achieve the desired pressure ratio in a single-stage fan with low radius ratio (0.38), and to maintain adequate stall margin. The fan has 44 tip-shrouded rotor blades and 90 outlet guide vanes. The two basic approaches taken in the acoustic design were: (1) minimization of noise at the source, and (2) suppression of the generated noise in the inlet and bypass exhaust duct. Suppression of the generated noise was accomplished in the inlet through use of the hybrid concept (wall acoustic treatment plus airflow acceleration suppression) and in the exhaust duct with extensive acoustic treatment including a splitter. The goal of the design was attainment of twenty effective perceived noise decibels (20 EPNdB) below current Federal Air Regulation noise standards for a full-scale fan at the takeoff, cutback, and approach conditions. The suppression goal of FAR 36-20 was not reached, but improvements in the technology of both front and aft fan-noise suppression were realized. The suppressed fan noise was shown to be consistent with the proposed federal regulation on aircraft noise.

Jutras, R. R.↗

NASA NTRS1977

Acoustic tests of augmentor wing model

Acoustic and aerodynamic data were obtained for a full-scale section of an augmentor wing. Features of the design included a single-row, multielement nozzle array and acoustically tuned panels placed on the interior surfaces of the augmentor. When the data were extrapolated to a 91,000-kilogram aircraft, the calculated sideline perceived noise levels were approximately the same for either the takeoff or approach condition.

Goodykoontz, J. H.↗

NASA NTRS1977

Effects of forward motion on jet and core noise

A study was conducted to investigate the effects of forward motion on both jet and core noise. Measured low-frequency noise from static-engine and from flyover tests with a DC-9-30 powered by JT8D-109 turbofan engines and with a DC-10-40 powered by JT9D-59A turbofan engines was separated into jet- and core noise components. Comparisons of the static and the corresponding in-flight jet- and core-noise components are presented. The results indicate that for the DC-9 airplane at low power settings, where core noise is predominant, the effect of convective amplification on core-noise levels is responsible for the higher in-flight low-frequency noise levels in the inlet quadrant. Similarly, it was found that for the DC-10 airplane with engines mounted under the wings and flaps and flap deflection greater than 30 degrees, the contribution from jet-flap-interaction noise is as much as 5 dB in the inlet quadrant and is responsible for higher in-flight low-frequency noise levels during approach conditions. Those results indicate that to properly investigate flight effects, it is important to consider the noise contributions from other low-frequency sources, such as the core and the jet-flap interaction.

Low, J. K. C.↗

NASA NTRS1978

Technology for return of planetary samples, 1977

Recent progress on the development of a basic warning system (BWS) proposed to assess the biohazard of a Mars sample returned to earth, an earth orbiting spacecraft, or to a moon base was presented. The BWS package consists of terrestrial microorganisms representing major metabolic pathways. A vital processes component of the BWS will examine the effects of a Mars sample at terrestrial atmospheric conditions while a hardy organism component will examine the effects of a Mars sample under conditions approaching those of the Martian environment. Any deleterious insult on terrestrial metabolism effected by the Mars sample could be indicated long before the sample reached earth proximity.

Source record↗

NASA NTRS1980

Analytical investigation of fan tone noise due to ingested atmospheric turbulence

The atmospheric turbulence involved in the fan noise generation is evaluated with an existing model for the atmospheric turbulence and an extended version of an existing model concerned with the effects of a flow contraction on convected turbulence. Fan tone noise due to ingested atmospheric turbulence is evaluated with existing fan noise models. The results indicate that the difference in fan narrowband noise due to atmospheric turbulence between static and flight landing approach conditions is in the order of 30 dB. It is concluded that fan noise due to atmospheric turbulence is insignificant in flight conditions for the fans used in the current high bypass ratio engines. The difference in fan narrowband noise between the two conditions is primarily due to the low intensity of the turbulence involved in fan noise generation in flight conditions. Fan noise due to atmospheric turbulence in static conditions should be reduced below the flight fan broadband noise levels which is best achieved with a reduction in the intensity of the fan inflow turbulence. Such a reduction can be obtained with the use of an inflow control device, low wind velocities, small surface roughness in the test stand environment, and large engine axis height above the ground. Peak sound power levels for fan tone noise due to ingested turbulence occur for transverse integral scales in the order of 25% of the rotor blade spacing in the fan tip region.

Ganz, U. W.↗

NASA NTRS1980

Core noise measurements from a small, general aviation turbofan engine

As part of a program to investigate combustor and other core noises, simultaneous measurements of internal fluctuating pressure and far field noise were made with a JT15D turbofan engine. Acoustic waveguide probes, located in the engine at the combustor, at the turbine exit and in the core nozzle wall, were used to measure internal fluctuating pressures. Low frequency acoustic power determined at the core nozzle exit corresponds in level to the far field acoustic power at engine speeds below 65% of maximum, the approach condition. At engine speeds above 65% of maximum, the jet noise dominates in the far field, greatly exceeding that of the core. From coherence measurements, it is shown that the combustor is the dominant source of the low frequency core noise. The results obtained from the JT15D engine were compared with those obtained previously from a YF102 engine, both engines having reverse flow annular combustors and being in the same size class.

Reshotko, M.↗

NASA NTRS1980

Core noise measurements from a small, general aviation turbofan engine

As part of a program to investigate combustor and other core noises, simultaneous measurements of internal fluctuating pressure and far field noise were made with a JT15D turbofan engine. Acoustic waveguide probes, located in the engine at the combustor, at the turbine exit and in the core nozzle wall, were used to measure internal fluctuating pressures. Low frequency acoustic power determined at the core nozzle exit corresponds in level to the far-field acoustic power at engine speeds below 65% of maximum, the approach condition. At engine speeds above 65% of maximum, the jet noise dominates in the far-field, greatly exceeding that of the core. From coherence measurements, it is shown that the combustor is the dominant source of the low frequency core noise. The results obtained from the JT15D engine were compared with those obtained previously from a YF102 engine, both engines having reverse flow annular combustors and being in the same size class.

Reshotko, M.↗

NASA NTRS1984

Micro-elastohydrodynamic Lubrication

Conventional elastohydrodynamics, which is based on assumption of smooth surfaces, is reviewed briefly to show its insufficiency for explaining the failure processes in these contacts. For conditions approaching failure, lubrication breakdown occurs locally at asperity contacts where the lubrication behavior is controlled by micro-elastohydrodynamic lubrication (Micro-EHL). Description is given to the film formation mechanisms in micro-EHL conjunctions. An assessment is made to the level of film thickness due to normal approach and sliding of a single asperity and due to asperlty-asperlty collision between two asperities; Possible influence of the micro-EHL to incipient scuffing failure, surface crack propagation and wear are discussed.

H S Cheng↗

NASA NTRS1985

Aerodynamic design considerations for efficient high-lift supersonic wings

A previously developed technique for selecting a design space for efficient supersonic wings is reviewed; this design-space concept is expanded to include thickness and camber effects and is evaluated for cambered wings at high-lift conditions. The original design-space formulation was based on experimental upper-surface and lower-surface normal-force characteristics for flat, uncambered delta wings; it is shown that these general characteristics hold for various thickness distributions and for various amounts of leading-edge camber. The original design-space formulation was also based on the assumption that the combination of Mach number and leading-edge sweep which would produce an equal division of flat-wing lift between the upper and lower surface would also be the proper combination to give the best cambered-wing performance. Using drag-due-to-lift factor as a measure of performance, for high-lift conditions cambered-wing performance is shown to significantly increase as conditions approach the design space; this correlation is demonstrated for both subcritical and supercritical flows.

Miller, D. S.↗

NASA NTRS1986

Approach trajectory planning system for maximum concealment

A computer-simulation study was undertaken to investigate a maximum concealment guidance technique (pop-up maneuver), which military aircraft may use to capture a glide path from masked, low-altitude flight typical of terrain following/terrain avoidance flight enroute. The guidance system applied to this problem is the Fuel Conservative Guidance System. Previous studies using this system have concentrated on the saving of fuel in basically conventional land and ship-based operations. Because this system is based on energy-management concepts, it also has direct application to the pop-up approach which exploits aircraft performance. Although the algorithm was initially designed to reduce fuel consumption, the commanded deceleration is at its upper limit during the pop-up and, therefore, is a good approximation of a minimum-time solution. Using the model of a powered-lift aircraft, the results of the study demonstrated that guidance commands generated by the system are well within the capability of an automatic flight-control system. Results for several initial approach conditions are presented.

Warner, David N., Jr.↗