Search NASA⌕ Search

SEARCH · Search NASA

Results for “contact angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Pore Structure and Wettability of Bossier Shale, East Texas, United States: Insights from Integrated Porosimetry, Scattering, and Imbibition Approaches

In this study, ascertaining the pore geometry and wettability characteristics of tight shales is of great significance for revealing the mechanisms of occurrence, migration, and production of shale resources. Taking the Bossier Shale collected from Well A, East Texas, USA, as an example, the pore geometry and wettability behavior in a broad nm-& μm scale pore spectrum were quantified based on integrated techniques, including water immersion porosimetry (WIP), mercury intrusion porosimetry(MIP), (ultra)small-angle X-ray scattering [(U)SAXS], contact angle, and liquid spontaneous imbibition (SI). Mainly owing to differences in the sample sizes used, data interpretation, as well as the detectable pore type (e.g., connected or not) and pore diameter ranges among different methods, sample porosities derived from WIP, MIP, and (U)SAXS were quite different, which range from 7.70 to 13.34%, 5.12 to 9.52%, and 2.48 to 6.44%, respectively. Therefore, a comparison of the porosities derived from different methods must be handled with utmost care. Additionally, although (U)SAXS is an effective technique for detecting both connected and non-connected pores, the fraction of non-connected pores could be underestimated by directly comparing the pore size distribution derived from (U)SAXS and MIP tests. This is because the sample sizes used for and pore information reflected by these two methods are different. Furthermore, the studied Bossier Shales exhibited various contact angle values and imbibition behaviors when using differently polarized liquids, revealing their mixed-wet characteristics. Comprehensively considering the differences in contact angle, imbibition slope, and imbibed liquid volume, three sub-categories of wettability behavior, with respect to more oil-wet, more water-wet, and intermediate mixed-wet, were qualitatively identified.

(U)SAXS↗
DOE OSTI2024

Surface Wettability Analysis from Adsorption Energy and Surface Electrical Charge

Surface wettability is determined by the attraction of a liquid phase to a solid surface. It is typically quantified by using contact angle measurements at mineral surfaces in the case of the flotation of mineral particles. Contact angle research to describe wettability has been investigated at different scales by sessile drop measurements, molecular dynamic simulation, and atomic force microscopy. In this study, the density functional theory (DFT) was employed for predicting the surface free energy and contact angles of a well-known hydrophobic phyllosilicate mineral talc and a well-known hydrophilic phyllosilicate mineral muscovite based on the calculated interfacial energy and surface charge. The results revealed that the predicted contact angle at the atomic scale was larger than the experimental value, and identified two interactions: electrostatic interaction and hydrogen bonding, between the hydrophilic muscovite surface and the water layer, while a water-exclusion zone of 3.346 Å was found between the hydrophobic talc surface and the first water layer. This investigation gives a new perspective for wettability determination at the atomic scale.

Geochemistry & Geophysics↗
DOE OSTI2022

Evaporation of Water Nanodroplets on Heated Surfaces: Does Nano Matter?

While experiments and continuum models have provided a relatively good understanding of the evaporation of macroscopic water droplets, elucidating how sessile nanodroplets evaporate is an open question critical for advancing nanotechnological applications where nanodroplets can play an essential role. In this study, using molecular dynamics simulations, we find that evaporating nanodroplets, in contrast to their macroscopic counterparts, are not always in thermal equilibrium with the substrate and that the vapor concentration on the nanodroplet surface does not reach a steady state. As a result, the evaporative behavior of nanodroplets is significantly different. Regardless of hydrophobicity, nanodroplets do not follow conventional evaporation modes but instead exhibit dynamic wetting behavior characterized by huge, non-equilibrium, isovolumetric fluctuations in the contact angle and contact radius. For hydrophilic nanodroplets, the evaporation rate, controlled by the vapor concentration, decays exponentially over time. Hydrophobic nanodroplets follow stretched exponential kinetics arising from the slower thermalization with the substrate. The evaporative half-lifetime of the nanodroplets is directly related to the thermalization time scale and therefore increases monotonically with the hydrophobicity of the substrate. Finally, the evaporative flux profile along the nanodroplet surface is highly nonuniform but does not diverge at the contact line as the macroscopic continuum models predict.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A particle finite element-based model for droplet spreading analysis

Here, a particle finite element method-based model is proposed to analyze droplet dynamics problems, particularly droplet spreading on solid substrates (wetting). The model uses an updated Lagrangian framework to formulate the governing equations of the liquid. The curvature of the liquid surface is tracked accurately using a deforming boundary mesh. In order to predict the spreading rate of the droplet on the solid substrate and track the corresponding contact angle evolution, dissipative forces at the contact line are included in the formulation in addition to the Navier-slip boundary conditions at the solid–liquid interface. The inclusion of these boundary conditions makes it possible to account for the induced Young’s stress at the contact line and for the viscous dissipation along the solid–liquid interfacial region. These are found to be essential to obtain a mesh-independent physical solution. The temporal evolution of the contact angle and the contact line velocity of the proposed model are compared with spreading droplets and micro-sessile droplet injection experiments and are shown to be in good agreement.

42 ENGINEERING↗
DOE OSTI2020

Wettability Effects on Falling Film Flow and Heat Transfer Over Horizontal Tubes in Jet Flow Mode

The performance of a falling-film heat exchanger is strongly linked to the surface characteristics and the heat transfer processes that take place over the tubes. The primary aim of this numerical study is to characterize the influence of surface wettability on the film flow behavior and its associated surface heat transfer in the jet-flow mode. Volume of fluid (VOF) based simulations are carried out for horizontal tubes with different surface wettabilities. The wettability of the tube surfaces is represented using the Kistler's dynamic contact angle model. Surface wettability effects ranging from superhydrophilic to superhydrophobic are studied by varying the equilibrium contact angle from 2 deg to 175 deg. Two different liquid mass flow rates of 0.06 and 0.18 kg/m-s corresponding to the inline and staggered jet flow modes are studied. Results are presented in terms of the liquid film thickness, the contact areas between the different phases (solid–liquid and liquid–air), and the heat transfer coefficient or Nusselt number. The resistance imposed by the increasing contact angles inhibits the extent of the liquid spreading over the tube surface, and this, in turn, influences the liquid film thickness, and the wetted area of the tube surface. A significant decrement in the heat transfer rate from the tube surfaces was observed as the equilibrium contact angle increased from 2 deg to 175 deg. The local distributions of the Nusselt number over the tube surface are strongly influenced by the flow recirculation in the liquid bulk.

Engineering↗
DOE OSTI2022

Hydrodynamics of countercurrent flow in an additive-manufactured column with triply periodic minimal surfaces for carbon dioxide capture

Computational investigation of the countercurrent flows in an additively manufactured (AM) column packed with triply periodic minimal surface (TPMS) is challenging. Multiphase flow simulations using the volume of fluid (VOF) method can explain the column’s hydrodynamic characteristics, including interfacial area, liquid holdup, pressure drop, flow regime, etc. The interfacial area is a key factor dictating the mass transfer via the absorption process, and thereby the overall efficiency of the column. The impacts of a solvent's physical properties, liquid and gas loads, and contact angle on the hydrodynamics are extensively explored. The solvents include traditional solvent (monoethanolamine [MEA]) used in industry as well as a water-lean solvent (EEMPA) as prospective solvents for carbon capture. As expected, interfacial area and liquid holdup increase with increasing liquid loads (q L ). The EEMPA exhibits higher values for the interfacial area and liquid holdup compared to those for the MEA. The dry and wet pressure drops per unit length in the column at different gas loads (F G ) are calculated and further compared with the empirical correlations for traditional packings. At low gas loads, i.e., in the preloading regime, the predicted values of the wet and dry pressure drops match well with the corresponding values calculated from available correlations. The gas load has a marginal impact on the interfacial area at its lower value, but the higher value of F G (>2.18 $\sqrt{Pa}$) causes flooding in the column. The effect of varying contact angles on the interfacial area and liquid holdup in the preloading regime is also studied. Both interfacial area and liquid holdup decrease with the increase in the value of the contact angle. Altogether, the effect of the contact angle on interfacial area is more pronounced than other parameters influencing the interfacial area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Wetting Properties of Molten Salts

Wettability is a key piece of information in understanding the behavior of molten salts at material interfaces. Wettability is most easily characterized by contact angle which is measurable using the sessile drop method. A modified sessile drop method was used to measure the contact angle of the LiCl-KCl eutectic at varying temperatures on Nickel 200, Hastelloy C276, Glassy Carbon, and MACOR machinable ceramic. The contact angle was used with existing surface temperature data to find the work of adhesion at various temperatures. Finally, problems encountered during the experiment are listed and possible improvements are provided.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Wetting behaviors of fluoroterpolymer fiber films

Various aspects of electrospun fibers prepared from terpolymer of tetrafluoroethylene (TFE), hexafluoropropylene (HFP), and vinylidene fluoride (VDF) (THV)/acetone solutions at two applied voltages, THV/acetone solutions having Texas montmorillonite with two ratios, and THV/ethyl acetate solutions using two needle sizes are described. Fibers from THV/acetone and THV/ethyl acetate solutions showed shallow indentations and pores, respectively. The clay, functioning as electrospinning agent, did not influence the fiber morphology, but yielded narrower fiber diameter distribution and the thinnest fibers. Heterogeneous fiber diameter distribution and increase in the fiber diameters were observed by lowering the voltage for fibers of THV/acetone solutions. Fibers from THV/ethyl acetate solutions had the largest diameter and the broadest diameter distribution. Electrospun THV fibers having both hydrophobic characteristics with nearly 140° water contact angles and oleophilic properties with oil contact angles less than 45° might have applications in areas such as water/oil separation.

02 PETROLEUM↗
DOE OSTI2024

Patterned Quasi-Liquid Surfaces for Condensation of Low Surface Tension Fluids

Extensive research concerns dropwise condensation of low surface tension fluids to promote energy efficiency and decarbonization in thermal energy systems. However, it is challenging as these fluids typically result in filmwise condensation. Drawing inspiration from the Namib desert beetle that enhances condensation through patterned wettability, conventional beetle-inspired surfaces excel in water condensation but flood when condensing low surface tension fluids. In this work, a patterned quasi-liquid surface is reported that achieves exceptional dropwise condensation of low surface tension fluids. The surface consists of alternating stripes with low surface energy, that is, a perfluoropolyether (PFPE) and fluorinated quasi-liquid surface (FQLS), that shows ultralow contact angle hysteresis for ethanol and hexane. Further, the PFPE stripes are slightly more slippery, acting as slippery bridges that accelerate droplet coalescence and removal. It is experimentally demonstrated that the striped PFPE-FQLS pattern exhibits a heat transfer coefficient 85%, 330%, and 550% higher than that of PFPE, fluorinated silane, and filmwise condensation, respectively. This study reveals that a high contact angle is desired to sustain dropwise condensation, irrespective of contact angle hysteresis. These findings provide a new paradigm for promoting the dropwise condensation of low surface tension fluids and offer valuable insights into surface design for energy sustainability.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Transmission interference fringe ( TIF ) technique for the dynamic visualization of evaporating droplet

Here, the transmission interference fringe (TIF) technique was developed to visualize the dynamics of evaporating droplets based on the Reflection Interference Fringe (RIF) technique for micro-sized droplets. The geometric formulation was conducted to determine the contact angle (CA) and height of macro-sized droplets without the need for the prism used in RIF. The TIF characteristics were analyzed through experiments and simulations to demonstrate a wider range of contact angles from 0 to 90°, in contrast to RIF's limited range of 0–30°. TIF was utilized to visualize the dynamic evaporation of droplets in the constant contact radius (CCR) mode, observing the droplet profile change from convex-only to convex-concave at the end of dry-out from the interference fringe formation. The TIF also observed the contact angle increase from the fringe radius increase. This observation is uniquely reported as the interference fringe (IF) technique can detect the formation of interference fringe between the reflection from the center convex profile and the reflection from the edge concave profile on the far-field screen. Unlike general microscopy techniques, TIF can detect far-field interference fringes as it focuses beyond the droplet-substrate interface. The formation of the convex-concave profile during CCR evaporation is believed to be influenced by the non-uniform evaporative flux along the droplet surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Evaporation from thin porous Coatings: Pore size effects and predictive equation for homogeneous coatings

Evaporation of small water droplets on solids is hindered because surface tension pulls the droplet into a spherical cap that has a small perimeter. Our solution is to coat a solid with a very thin, porous layer into which the droplet flows to create a large-area disk with concomitant high rate of evaporation. We investigate evaporation by varying factors that have not been previously considered: pore size and distribution, contact angle, temperature, and relative humidity (RH). A larger pore size resulted in faster evaporation, which we explain through faster transport within the coating. Even faster evaporation occurred for a bilayer structure with small particles on the air side and larger particles on the solid side. Further, the water advancing contact angle had an insignificant effect in the range from < 10° through to 60°. Our results for different pore sizes, temperature, humidity, and contact angle all collapse onto a single curve when appropriately normalized. This validates an equation that can be used for the evaporation from a homogeneous coating that depends only one empirical factor and the droplet volume. Since the volume is often user-controlled, we envisage that this equation can be used to predict evaporation and guide design of fast-drying coatings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Caprock Remains Water Wet Under Geologic CO 2 Storage Conditions

Abstract Carbon storage technology is primarily targeted in saline formations, which is a porous rock matrix filled with brine, sealed with a low permeability caprock. There are significant variations of CO 2 wetting properties, typically reported in the literature as contact angle of CO 2 and brine interacting with a rock material, suggesting that CO 2 could become wetting under geostorage conditions and negatively impact containment effectiveness. Here, we performed the first controlled laboratory measurements of CO 2 ‐brine contact angles on shale rocks from low permeability sealing formations with distinctive mineralogic properties—calcite‐rich, quartz‐rich, and dolomite‐rich. We targeted temperatures at 40° and 100°C, pressures at 8.3, 34.5, and 62.1 MPa, and salinity at 35,000 and 260,000 ppm. Results show no significant change in contact angle with mineralogy, temperature, pressure, salinity, and CO 2 bubble size. We conclude that caprocks will remain water‐wet at geologic CO 2 storage conditions and will not lose their capillary sealing capacity.

Tapriyal, Deepak↗
DOE OSTI2022

Tuning the fluid wetting dynamics on gold microstructures using photoactive compounds

This work demonstrates how photoactive compounds can be used to tune the surface chemistry, surface free energy, and the wetting velocity of fluids on Spiropyran functionalized surfaces with different surface microstructures. Evidence of this photowetting effect is based on data showing: (1) the cyclic changes in the static, advancing, and receding contact angles $\theta$ CA for multiple UV$\rightleftarrows$vis photoswitching cycles with both smooth and microstructured surfaces and (2) the changes in the fluid wicking velocity (via UV$\rightleftarrows$vis photoswitching) on different Spiropyran functionalized hemiwicking surfaces. X-ray photoelectron spectroscopy is used to determine the efficiency of photoswitching caused by the quality of the Spiropyran functionalization. Reversible photoisomerization of Spiropyran generates a gradient in surface free energy, resulting in a similar change in contact angle ($\theta$ CA ) in the photoswitchable surfaces. In conclusion, by incorporating these changes into the Owens-Wendt and Van Oss surface energy models, the energy of smooth Au surfaces can also be predicted for both UV and visible light irradiations, where reversible contact angle variations of $\Delta$$\theta$ CA ≈ 5–10° are achieved with both water and water-ethanol mixtures due to the conversion of SP to merocyanine, which corresponds to a total free energy change of ~13% on the photoswitchable surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Durable polymer-aerogel based superhydrophobic coatings: a composite material

Provided are polymer-aerogel composite coatings, devices and articles including polymer-aerogel composite coatings, and methods for preparing the polymer-aerogel composite. The exemplary article can include a surface, wherein the surface includes at least one region and a polymer-aerogel composite coating disposed over the at least one region, wherein the polymer-aerogel composite coating has a water contact angle of at least about 140° and a contact angle hysteresis of less than about 1°. The polymer-aerogel composite coating can include a polymer and an ultra high water content catalyzed polysilicate aerogel, the polysilicate aerogel including a three dimensional network of silica particles having surface functional groups derivatized with a silylating agent and a plurality of pores.

Kissel, David J.↗
DOE OSTI2025

Wettability of Two-Dimensional Carbon Allotropes from Molecular Simulations

Force-field Monte Carlo and Molecular Dynamics simulations are used to compare wetting behaviors of model carbon sheets mimicking neat graphene, its saturated derivative, graphane, and related planar allotropes penta-graphene, γ-graphyne, and ψ-graphene in contact with aqueous droplets or an aqueous film confined between parallel carbon sheets. Atomistic and area-integrated surface/water potentials are found to be essentially equivalent in capturing moderate differences between the wetting free energies of tested substrates. Despite notable differences in mechanical and electric properties of distinct allotropes, the predicted allotrope/water contact angles span a narrow window of weakly hydrophilic values. Contact angles in the range of 80 ± 10° indicate modest hydration repulsion incapable of competing with van der Waals attraction between carbon particles. Poor dispersibility in neat water is hence a common feature of studied materials.

Biochemistry & Molecular Biology↗
DOE OSTI2020

Characterizing the Evolution of Trapped scCO 2 Curvature in Bentheimer and Nugget Sandstone Pore Geometry

During a Geologic Carbon Storage process, supercritical CO 2 (scCO 2 ) is subjected to a series of dynamic and static conditions where the relationship between pore geometry and the trapped scCO 2 curvature remains to be established. To mimic the dynamic process, two sandstones, Bentheimer and Nugget, were subjected to two successive drainage and imbibition (D-I) cycles and X-ray computed tomography scanned at each residual state to capture the wettability evolution at static conditions in the same pore geometry. Both sandstones contain similar grain size distributions, pore size distributions, and pore interconnectivity but differ in that the Nugget formation contains approximately half the porosity of the Bentheimer sandstone, and the pore network contains dead-end pores. scCO 2 size distributions, strain calculations, and geometric contact angle measurements were used to characterize the curvature of scCO 2 in different pore types between cycles. An increase in geometric contact angle was the greatest when advancement along the pore network of the same ganglion occurred between cycles while strain increased the most with pore-filling trapping. Moreover, Nugget sandstone results in a greater aggregated residual saturation and shows a clear increase in scCO 2 sizes with an additional D-I cycle while scCO 2 in the Bentheimer core shows a more complex response with some ganglion increasing and some decreasing in size with an additional D-I cycle. From this work, we suspect the pore geometry is playing a role in scCO 2 size distributions and use this information to suggest using water pulses to enhance trapping capacity in lower porosity sandstones.

58 GEOSCIENCES↗
DOE OSTI2020

Negatively Charged Lipids Exhibit Negligible Effects on the Water Repellency of Montmorillonite Films

Amphiphilic molecules can alter the wettability of soil minerals. To determine how the headgroup chemistry of amphiphiles determines these effects, we investigate a system of the clay montmorillonite with long-chain phospholipids. We use phosphatidylglycerol (PG) phospholipids to contrast with our previous work using phosphatidylethanolamine lipids (PE). Zwitterionic PE lipids can sorb to the negatively-charged montmorillonite surface, whereas negatively-charged PG lipids cannot. Employing a suite of techniques from molecular dynamics, atomic force microscopy, fluorescence microscopy, and contact angle measurements, we define sample characteristics from molecular scale structure to the macroscopic wettability. We find that PG lipids do not significantly alter montmorillonite wetting characteristics, such as the contact angle, flow viscosity, and the characteristic timescale for droplet imbibition. In comparing PE and PG lipid/clay films, we find that, among the phospholipids compared, they must have three characteristics in order to change clay/lipid film wettability: they must bind to the mineral surface, be solid at room temperature, and have a relatively continuous distribution throughout the film.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Superhydrophobic to superhydrophilic wettability transition of functionalized SiO 2 nanoparticles

The superhydrophobic and superhydrophilic surfaces and their transitions are of great interest for the production of self-cleaning, anti-biofouling, or corrosion-resistant materials. This research reports the wettability transition from superhydrophobic to superhydrophilic SiO 2 nanoparticles functionalized with 1H, 1H, 2H, 2H-perfluorooctyltriethoxysilane (POTS) and induced by temperature. The functionalization of these nanoparticles was confirmed by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy. The functionalization of SiO 2 nanoparticles with POTS resulted in superhydrophobic surfaces with water contact angles up to 157°. A sudden transition to superhydrophilic behavior with water contact angles (WCA) below 5° was observed when the sample was heat-treated at 500 °C, despite the presence of fluorine on the surface of these nanoparticles, as confirmed by XPS and transmission electron microscopy. XPS suggested that the transition was caused by the change in orientation of the fluoroalkyl molecules and its partial decomposition due to the loss of the –CF 3 group, resulting in shorter chains with a tail-end group with C–O bonds, which promoted the superhydrophilicity.

36 MATERIALS SCIENCE↗