SEARCH · Search NASA

Results for “debond energy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Cyclic debonding of adhesively bonded composites

To analyze the fatigue behavior of a simple composite-to-composite bonded joint, a combined experimental and analytical study of the cracked-lap-shear specimen subjected to constant-amplitude cyclic loading was undertaken. Two bonded systems were studied: T300/5208 graphite/epoxy adherends bonded with adhesives EC 3445 and with FM-300. For each bonded system, two specimen geometries were tested: (1) a strap adherend of 16 plies bonded to a lap adherend of 8 plies, and (2) a strap adherend of 8 plies bonded to a lap adherend of 16 plies. In all specimens tested, the fatigue failure was in the form of cyclic debonding with some 0 deg fiber pull-off from the strap adherend. The debond always grew in the region of adhesive that had the highest mode I (peel) loading and that region was close to the adhesive-strap interface. Furthermore, the measured cyclic debond growth rates correlated well with total strain energy release rates G(T) as well as with its components G(I) (peel) and G(II) (shear) for the mixed-mode loading in the present study.

Mall, S.↗

NASA NTRS1985

Mixed-mode cyclic debonding of adhesively bonded composite joints

A combined experimental-analytical investigation to characterize the cyclic failure mechanism of a simple composite-to-composite bonded joint is conducted. The cracked lap shear (CLS) specimens of graphite/epoxy adherend bonded with EC-3445 adhesive are tested under combined mode 1 and 2 loading. In all specimens tested, fatigue failure occurs in the form of cyclic debonding. The cyclic debond growth rates are measured. The finite element analysis is employed to compute the mode 1, mode 2, and total strain energy release rates (i.e., GI, GII, and GT). A wide range of mixed-mode loading, i.e., GI/GII ranging from 0.03 to 0.38, is obtained. The total strain energy release rate, G sub T, appeared to be the driving parameter for cyclic debonding in the tested composite bonded system.

Rezaizadeh, M. A.↗

NASA NTRS1984

Repeatability of mixed-mode adhesive debonding

The repeatability of debond growth rates in adhesively bonded subjected to constant-amplitude cyclic loading was studied. Debond growth rates were compared from two sets of cracked-lap-shear specimens that were fabricated by two different manufacturers and tested in different laboratories. The fabrication method and testing procedures were identical for both sets of specimens. The specimens consisted of aluminum adherends bonded with FM-73 adhesive. Critical values of strain-energy-release rate were also determined from specimens that were monotonically loaded to failure. The test results showed that the debond growth rates for the two sets of specimens were within a scatter band which is similar to that observed in fatigue crack growth in metals. Cyclic debonding occurred at strain-energy-release rates that were more than an order of magnitude less than the critical strain-energy-release rate in static tests.

Everett, R. A., Jr.↗

NASA NTRS1985

Repeatability of mixed-mode adhesive debonding

The repeatability of debond growth rates in adhesively bonded subjected to constant-amplitude cyclic loading was studied. Debond growth rates were compared from two sets of cracked-lap-shear specimens that were fabricated by two different manufacturers and tested in different laboratories. The fabrication method and testing procedures were identical or both sets of specimens. The specimens consisted of aluminum adherends bonded with FM-73 adhesive. Critical values of strain-energy-release rate were also determined from specimens that were monotonically loaded to failure. The test results showed that the debond growth rates for the two sets of specimens were within a scatter band which is similar to that observed in fatigue crack growth in metals. Cyclic debonding occurred at strain-energy-release rates that were more than an order of magnitude less than the critical strain-energy-release rate in static tests.

Everett, R. A., Jr.↗

NASA NTRS1985

Delamination micromechanics analysis

A three-dimensional finite element analysis was developed which includes elastoplastic, orthotropic material response, and fracture initiation and propagation. Energy absorption due to physical failure processes characteristic of the heterogeneous and anisotropic nature of composite materials is modeled. A local energy release rate in the presence of plasticity was defined and used as a criterion to predict the onset and growth of cracks in both micromechanics and macromechanics analyses. This crack growth simulation technique is based upon a virtual crack extension method. A three-dimensional finite element micromechanics model is used to study the effects of broken fibers, cracked matrix and fiber-matrix debond on the fracture toughness of the unidirectional composite. The energy release rates at the onset of unstable crack growth in the micromechanics analyses are used as critical energy release rates in the macromechanics analysis. This integrated micromechanical and macromechanical fracture criterion is shown to be very effective in predicting the onset and growth of cracks in general multilayered composite laminates by applying the criterion to a single-edge notched graphite/epoxy laminate subjected to implane tension normal to the notch.

Adams, D. F.↗

NASA NTRS1989

Effect of bond thickness on fracture and fatigue strength of adhesively bonded composite joints

An experimental investigation of composite to composite bonded joints was undertaken to study the effect of bond thickness on debond growth rate under cyclic loading and critical strain energy release rate under static loading. Double cantilever beam specimens of graphite/epoxy adherends bonded with EC 3445 were tested under mode I loading. A different behavior of fracture and fatigue strength was observed with variation of bondline thickness.

Mall, S.↗

NASA NTRS1986

Stress analysis of the cracked lap shear specimens: An ASTM round robin

This ASTM Round Robin was conducted to evaluate the state of the art in stress analysis of adhesively bonded joint specimens. Specifically, the participants were asked to calculate the strain-energy-release rate for two different geometry cracked lap shear (CLS) specimens at four different debond lengths. The various analytical techniques consisted of 2- and 3-dimensional finite element analysis, beam theory, plate theory, and a combination of beam theory and finite element analysis. The results were examined in terms of the total strain-energy-release rate and the mode I to mode II ratio as a function of debond length for each specimen geometry. These results basically clustered into two groups: geometric linear or geometric nonlinear analysis. The geometric nonlinear analysis is required to properly analyze the CLS specimens. The 3-D finite element analysis gave indications of edge closure plus some mode III loading. Each participant described his analytical technique and results. Nine laboratories participated.

Johnson, W. S.↗

NASA NTRS1987

Stress analysis of the cracked-lap-shear specimen - An ASTM round-robin

Johnson, W. S.↗

NASA NTRS1991

Variational mechanics analysis of the stresses in microdrop debond specimens

A recently derived variational mechanics analysis of stresses in single-fiber model composites has been applied to the analysis of the stresses in the microdrop debond specimen. The new analysis is more accurate than the commonly applied shear-lag or elastic-plastic analyses. The results from a sample stress state calculation suggest that interfacial failure between the fiber and the microdrop is by mode I or opening mode failure at the beginning of the microdrop. The opening mode failure is caused by a large tensile radial stress at the fiber/matrix interface. Previous analyses of microdrop debond data have been in terms of a shear strength. It is suggested that these analyses misrepresent microdrop debond results and recommend instead a failure analysis based on energy release rate and interfacial fracture toughness. A procedure for calculating the energy release rate for the growth of an interfacial crack is described.

Scheer, Robert J.↗

NASA NTRS1978

Effects of debonds on the strength of composite plates

The effect of debonds on composite structures under compressive loads is investigated in this paper. Because of the inclusion of debonds, unsymmetric laminated rectangular plates are considered. The resulting bending-extension coupling is included and is shown to be quite significant for thin laminates typical of debonded regions. The solution technique is based on the Theorem of Minimum Potential Energy; and both simply supported and clamped boundaries are considered. The need to include transverse shear deformation in the analysis is documented. Also, the range of applicability of the reduced stiffness matrix technique for such plates is stated. The consideration of non-rectangular boundaries, as would normally occur for debonded regions, has been included through a finite element study. Using the results of this study, an effective laminated plate theory for irregularly shaped debonded regions is proposed.

Daugherty, R. L.↗

NASA NTRS1991

Graphite/copper alloy interfacial energies determined using the sessile drop method

Graphite surfaces are not wet by pure copper. This lack of wetting is responsible for a debonding phenomenon that was found in continuous graphite fiber/copper matrix composites materials subjected to elevated temperatures. By suitably alloying copper, its capability to wet graphite surfaces can be enhanced. In situ measurements of graphite/copper alloy wetting angles were made using the sessile drop method. Interfacial energy values were calculated based upon these measurements.

Devincent, Sandra M.↗

NASA NTRS1991

Development of graphite/copper composites utilizing engineered interfaces

In situ measurements of graphite/copper alloy contact angles were made using the sessile drop method. The interfacial energy values obtained from these measurements were then applied to a model for the fiber matrix interfacial debonding phenomenon found in graphite/copper composites. The formation obtained from the sessile drop tests led to the development of a copper alloy that suitably wets graphite. Characterization of graphite/copper alloy interfaces subjected to elevated temperatures was conducted using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Auger Electron Spectroscopy, and X Ray Diffraction analyses. These analyses indicated that during sessile drop tests conducted at 1130 C for 1 hour, copper alloys containing greater than 0.98 at pct chromium form continuous reaction layers of approx. 10 microns in thickness. The reaction layers are adherent to the graphite surface. The copper wets the reaction layer to form a contact angle of 60 deg or less. X ray diffraction results indicate that the reaction layer is Cr3C2.

Devincent, Sandra M.↗

NASA NTRS1969

An analysis of adhesive debonding in case-bonded solid propellant rocket motors

Adhesive debonding in case-bonded solid propellant rocket motors, describing stress analysis and interfacial surface energy measurement

Kunio, T.↗

NASA NTRS1986

An integrated micromechanical and macromechanical approach to fracture behavior of fiber-reinforced composites

A novel integrated micromechanical and macromechanical fracture criterion (IMMFC) was developed for the purpose of characterizing fractures in fiber-reinforced composites. The Griffith energy balance equation was modified to include the energy absorption due to matrix yielding, matrix cracks, fiber breaks, and fiber-matrix interface debonds characteristic for these materials. Parameters which are a measure of the size and density of the microflaws are introduced into the development of the IMMFC, and the concept of the R-curve is used to bridge the micromechanics and macromechanics approaches.

Mahishi, Jayant M.↗

NASA NTRS1994

Strength characteristics and crack growth behavior of a composite with well aligned fibers

Continuous fiber composites have shown tremendous promise in industrial applications. Their microstructures, however, are very complex and in many instances difficult to characterize. In this project, the fracture characteristics of a specially made fiber reinforced composite with different fiber spacing are investigated. The experimental results so far have shown that after an initial transient phase the crack speed reaches a steady phase, i.e., independent of the crack length. Within the steady crack growth phase debonding along the fibers in the bridging zone grows in a self-similar manner. During the steady phase the energy dissipation per cycle is constant. Afterwards, an increase of the energy dissipation is observed that is accompanied by a decrease in crack speed. This latter trend is presumed to be the result of relatively large amounts of energy dissipated in the bulk of the specimen. Using appropriate Green's function and computer simulations, the stress intensity factor at the crack tip is evaluated for various cases of bridging stresses. In this way the effects of specimen size and fiber spacing on the overall fracture behavior of the composite system are analyzed. The steady crack speed and the steady rate of debonding have a similar power dependence on stress level. Dimensional analysis demonstrates that the particular fracture process is not governed by dimensional invariance but on the detailed micromechanisms in the bridging zone.

Botsis, John↗

NASA NTRS1982

The role of peel stresses in cyclic debonding

When an adhesively bonded joint is undergoing cyclic loading, one of the possible damage modes that occurs is called cyclic debonding - progressive separation of the adherends by failure of the adhesive bond under cyclic loading. In most practical structures, both peel and shear stresses exist in the adhesive bonding during cyclic loading. The results of an experimental and analytical study to determine the role of peel stresses on cyclic debonding in a mixed mode specimen are presented. Experimentally, this was done by controlling the forces that create the peel stresses by applying a clamping force to oppose the peel stresses. Cracked lap shear joints were chosen for this study. A finite element analysis was developed to assess the effect of the clamping force on the strain energy release rates due to shear and peel stresses. The results imply that the peel stress is the principal stress causing cyclic debonding.

Everett, R. A., Jr.↗

NASA NTRS2002

Analysis of Composite Skin-Stiffener Debond Specimens Using Volume Elements and a Shell/3D Modeling Technique

The debonding of a skin/stringer specimen subjected to tension was studied using three-dimensional volume element modeling and computational fracture mechanics. Mixed mode strain energy release rates were calculated from finite element results using the virtual crack closure technique. The simulations revealed an increase in total energy release rate in the immediate vicinity of the free edges of the specimen. Correlation of the computed mixed-mode strain energy release rates along the delamination front contour with a two-dimensional mixed-mode interlaminar fracture criterion suggested that in spite of peak total energy release rates at the free edge the delamination would not advance at the edges first. The qualitative prediction of the shape of the delamination front was confirmed by X-ray photographs of a specimen taken during testing. The good correlation between prediction based on analysis and experiment demonstrated the efficiency of a mixed-mode failure analysis for the investigation of skin/stiffener separation due to delamination in the adherents. The application of a shell/3D modeling technique for the simulation of skin/stringer debond in a specimen subjected to three-point bending is also demonstrated. The global structure was modeled with shell elements. A local three-dimensional model, extending to about three specimen thicknesses on either side of the delamination front was used to capture the details of the damaged section. Computed total strain energy release rates and mixed-mode ratios obtained from shell/3D simulations were in good agreement with results obtained from full solid models. The good correlations of the results demonstrated the effectiveness of the shell/3D modeling technique for the investigation of skin/stiffener separation due to delamination in the adherents.

Krueger, Ronald↗

NASA NTRS2001

Damage Tolerance of Sandwich Plates With Debonded Face Sheets

A nonlinear finite element analysis was performed to simulate axial compression of sandwich beams with debonded face sheets. The load - end-shortening diagrams were generated for a variety of specimens used in a previous experimental study. The energy release rate at the crack tip was computed using the J-integral, and plotted as a function of the load. A detailed stress analysis was performed and the critical stresses in the face sheet and the core were computed. The core was also modeled as an isotropic elastic-perfectly plastic material and a nonlinear post buckling analysis was performed. A Graeco-Latin factorial plan was used to study the effects of debond length, face sheet and core thicknesses, and core density on the load carrying capacity of the sandwich composite. It has been found that a linear buckling analysis is inadequate in determining the maximum load a debonded sandwich beam can carry. A nonlinear post-buckling analysis combined with an elastoplastic model of the core is required to predict the compression behavior of debonded sandwich beams.

Sankar, Bhavani V.↗