Search NASA⌕ Search

SEARCH · Search NASA

Results for “deionized water”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Grid-to-rod fretting wear study of SiC/SiC composite accident-tolerant fuel claddings using an autoclave fretting bench test

Grid-to-rod-fretting (GTRF) in pressurized water reactors (PWRs) is known to cause wear and surface damage on the fuel claddings, potentially leading to radioactive leakage. One of the accident-tolerant fuel (ATF) concepts is to use advanced cladding materials that could withstand higher temperatures. Here, we investigated the wear behavior of candidate silicon carbide (SiC)-based composite claddings with different levels of surface finish in fretting against a commercial ZIRLO alloy grid using a unique bench-scale autoclave GTRF rig. The experiments mimicked the environment in an industrial full-assembly PWR simulator. Fretting tests were conducted with a realistic load (~0.5 N) in deionized water under a pressure of 20–23 bar at 204 °C for 100 h. While the SiC/SiC composite claddings showed significantly higher wear resistance than the commercial ZIRLO alloy cladding as expected, the smoother versions experienced surprisingly higher wear than the much softer counterface, ZIRLO grid. The wear mechanism of the SiC/SiC cladding was attributed to the SiC wear debris that was trapped at the fretting interface causing both 3-body and 2-body (embedded into the grid surface) abrasion of the cladding. Rougher SiC/SiC claddings had less material loss but caused more wear on the ZIRLO grid. Finally, pre-oxidized ZIRLO grid showed better compatibility with the SiC/SiC cladding to protect both the cladding and grid as a result of reduced wear debris trapping.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Determining the Solubility Behavior of Kogarkoite in Simulated Nuclear Waste

Kogarkoite (Na 3 FSO 4 ) is a sparingly soluble fluoride–sulfate double salt that has been identified in high level nuclear waste sludge at the Hanford Site and, more recently, in sludge batch compilation samples at the Savannah River Site (SRS). Due to its complex dissolution behavior, which exhibits an inverse dependence on sodium ion activity, the presence of this mineral poses significant challenges to waste retrieval and processing. Incomplete dissolution during sludge washing can lead to the retention of fluoride and sulfate in the high-level waste feed, potentially causing the formation of corrosive, immiscible molten salt layers, known as "glass gall,” in vitrification melters. Current efforts to optimize flowsheet parameters and wash-water volumes are hindered by the absence of a commercially available, certified reference material, which prevents the accurate calibration of analytical methods and the verification of dissolution kinetics. To address this critical gap, this research focuses on the laboratory synthesis of pure Kogarkoite to serve as a standard for comprehensive solubility and washing performance testing. A coupled synthesis and simulant campaign was executed using an evaporative crystallization protocol designed to replicate the dynamic concentration effects observed in tank farm operations. Thirteen simulant matrices were prepared by dissolving systematically varied ratios of sodium fluoride (NaF) and sodium sulfate (Na 2 SO 4 ) in deionized water under three distinct caustic regimes: 0.0 g (control), 4.0 g (~1 M), and 12.0 g (~3 M) sodium hydroxide (NaOH). While thermodynamic equilibrium models suggest that high-caustic environments should favor the stability of the double salt7, results from this evaporative study at 25 0 C revealed a distinct kinetic divergence. Simulants with high hydroxide loading predominantly yielded large, blocky crystals of sodium sulfate decahydrate (Na 2 SO 4 .10H 2 O). Successful synthesis of pure Kogarkoite was achieved exclusively in specific NaOH-free compositional windows, where the precipitate manifested as fine, opaque granular aggregates. Ion chromatography (IC) analysis confirmed phase purity through the simultaneous stoichiometric depletion of both fluoride and sulfate from the supernatant. This successful synthesis establishes a reproducible route to generate bulk Kogarkoite, enabling the subsequent phase of quantitative dissolution testing using inhibited water to optimize sludge-batch assembly.

Sarker, Md Sharif [Florida International Univ. (FI↗
DOE OSTI2020

Autoclave grid-to-rod fretting wear evaluation of a candidate cladding coating for accident-tolerant fuel

In pressurized water reactors (PWRs), water flow induced vibrations cause contact and rubbing between the fuel rods and the supporting grid, a phenomenon known as Grid-to-Rod-Fretting (GTRF). GTRF may produce progressive wear damage on the fuel claddings leading to subsequent leakage of radioactive fission products. Various accident-tolerant fuel (ATF) concepts are being developed for higher resistance to the high temperature steam and one approach is to apply a cladding coating. Here, fretting wear behavior of a candidate Cr-coating was investigated using a unique bench-scale autoclave testing rig mimicking the environment in an industrial full-assembly PWR simulator. The contact was under a realistically low load (~0.5 N) lubricated by deionized water at a temperature of 204 °C under a pressure of 20-23 bars. Results demonstrated that the Cr-coating significantly improved the cladding's wear resistance when tested against a commercial ZIRLO grid with or without pre-oxidization. In addition, the Cr-coating also reduced wear on the non-oxidized ZIRLO grid but slightly increased the wear on the pre-oxidized grid.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Effect of seawater as mixing water on the hydration behaviour of tricalcium aluminate

This study explored the mechanism of the effect of seawater on tricalcium aluminate (C{sub 3}A) hydration. The results showed that seawater retarded C{sub 3}A hydration and reduced the reaction degree of C{sub 3}A. The co-existence or ion pairing of Ca{sup 2+} and SO{sub 4}{sup 2−} onto the surface of C{sub 3}A poisoning the reactive sites is the main reason for this retardation. Besides, the precipitation of Mg(OH){sub 2} on the surface of C{sub 3}A would prolong the induction period for another 30 min and then consequently decrease the dissolution rate of C{sub 3}A hydration. Trace amounts of MgSO{sub 4}{sup 0} and Mg{sup 2+} present in the alkaline solution had little retardation effect. It was also found that Cl{sup −} would preferentially react with C{sub 3}A to form Friedel's salt, rather than forming hydroxy-AFm as that in the C{sub 3}A-deionized water paste. The direct formation of Friedel's salt resulted in an accumulation of Al{sup 3+} in solution, which would also hinder the subsequent dissolution of C{sub 3}A.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Lead Adsorption and Desorption at the Barite (001) Surface in the Presence of EDTA

Scaling minerals, such as barite, can cause detrimental consequences for oil/gas pipelines and water systems, but their formation can be inhibited by organic chelators such as ethylenediaminetetraacetic acid (EDTA). Here, we resolve how EDTA affects sorption and desorption of Pb at the barite (001) surface using a combination of X-ray scattering and microscopy measurements. In the presence of EDTA, Pb incorporated in the topmost part of the barite surface and adsorbed as inner-sphere complexes on the surface. In barite saturated solutions containing [Pb] ≥ 100 μM, overgrowth films grew along step edges. These films were exclusively monolayer thick, indicating that their growth was a self-limiting process. Approximately half of the Pb was removed after 14.5 h reaction with a Pb-free EDTA solution where most of the desorption occurred to adsorbed Pb rather than incorporated Pb. Dissolution proceeded primarily via step retreat and etch pit formation in EDTA, but in deionized water, the secondary phase was quickly removed within 3 min. Together these results suggest EDTA binds to both the surface and Pb in solution, which limits Pb sorption. However, EDTA binding to the surface also inhibits removal of the secondary phase that formed at higher Pb concentrations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Permeability of Single–Layer–Free–Standing Meshes at Varying Capillary Pressure via a Novel Method

The permeability of mesh wicks is important for various applications, including two–phase heat transfer. However, the understanding of the permeability of single–layer, free–standing mesh wicks, with liquid–gas interfaces on both sides, is limited. A novel and simpler method is presented to determine the permeability of a free–standing wick and apply it to a representative mesh. This method involves modifying the capillary pressure via elevation and simultaneously measuring the permeability to determine the permeability–capillary pressure relationship. When applied to a copper mesh with plain weave having undergone surface cleaning, the permeability is found to decrease as capillary pressure for deionized water increases. A dimensional analysis is presented to generalize this data for other mesh sizes with similar weaves and fluids. The behavior of mesh in application is modeled, based on the integration of Darcy's law with an analytic function fit to measured data, and parametric studies are conducted to investigate the superficial velocity of liquids through the mesh under varying driving pressures, transport lengths, and liquid viscosity, based on the obtained capillary pressure–permeability relationship. This study provides valuable insights into the transport properties of mesh wicks, with potential applications in fields such as electronics cooling, electrochemical devices, and fluid purification technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Direct Recycling of Blended Cathode Materials by Froth Flotation

We report that direct Li-ion battery recycling involves separating cathode active materials in the solid phase while preserving their electrochemical performance. To reuse the recycled ones in new batteries, it is necessary to separate individual cathode components, which would typically occur prior to the rejuvenation and any compositional reformulation processes. Herein, a froth flotation process is developed to separate pristine lithium nickel-manganese-cobalt oxide (LiNi 0.333 Mn 0.333 Co 0.333 O 2 , NMC111) and lithium manganese oxide (LMO) materials. The flotation results show that with multiple stages of the separation processes, a satisfactory separation is achieved with 95% grade or above of NMC111 in the froth product and 95% grade of LMO in the tailing product. The electrochemistry results show that the flotation chemicals have negligible impact on the electrochemical performance of recycled active materials, whereas the NMC111 exhibits a minor capacity fade after being in contact with deionized water at 2% solid concentration. An improvement in both the rate and cycling performance is achieved at 10% solid concentration or higher. It is found that there is little compositional and structural change to the aqueous recycled NMC111 powders. An effective and low-cost separation method for direct recycling mixed cathode compositions is demonstrated.

25 ENERGY STORAGE↗
DOE OSTI2024

Geochemical assessment of mineral sequestration of carbon dioxide in the midcontinent rift

Abstract This study examines the potential of Midcontinent Rift rocks to facilitate long‐term CO 2 sequestration by providing the necessary Ca and Mg for carbonate mineralization. Surface samples were collected from the Oronto and Bayfield‐Jacobsville Groups around Lake Superior and used for petrography and X‐ray diffraction to determine their mineral composition. Also, X‐ray fluorescence was also used to assess their bulk chemical composition. The samples were then exposed to CO 2 and deionized water in Teflon‐lined vessels at 90°C, and the resulting leachate fluids were analyzed for the cation released during the testing. SEM microscopy was used to examine the samples for potential mineralization of carbonate minerals. The Oronto Group sediments consist primarily of feldspathic to feldspathic lithic arenites with a chlorite‐dominated matrix, and the primary porosity is blocked by calcite and hematite cement. The Bayfield–Jacobsville sequences are porous quartz arenites to feldspathic quartz arenites that do not contain significant accumulation of Ca‐, Mg‐, and Fe‐bearing minerals. The leachate fluids obtained from Oronto Group samples exhibit a maximum Ca release rate (5.2 × 10 −4 mole/cm 2 .day), indicating rapid calcite cement dissolution and increased porosity and permeability. SEM/EDS microanalysis revealed areas where pore‐filling calcite was preferentially dissolved. Longer‐term rock‐water reactions resulted in induced carbonate mineralization, as evidenced by calcite crystals observed in a sample reacted for 102 days. © 2024 Society of Chemical Industry and John Wiley & Sons, Ltd.

Energy & Fuels↗
DOE OSTI2024

The Critical Influence of Spin–Dry Technique on the Surface Passivation Quality of Crystalline Silicon Solar Cell Structures

This study examines the effects of spin-dry (SD) and N 2 blow-dry (ND) techniques on the quality and surface passivation performance of silicon oxide grown in ozone-dissolved deionized water. The SD method achieves greater oxide thickness uniformity, averaging 1.39 nm ± 4.17% across 49 points, compared to 1.68 nm ± 21.67% for the ND wafers. However, persistently poor passivation of ozonated oxide-grown wafers following the SD process is exhibited, with carrier lifetime, τ eff < 0.3 ms and saturation current density, J 0 (per side) ranging from 26 to 45 fA cm 2 . These findings are analyzed in the context of the fundamental phenomena involved in the drying processes of both techniques. Following this, an optimized spin-drying process is developed, resulting in improved τ eff and J 0 values of 1.4 ms and 5.6 fA cm –2 , respectively. Scanning electron microscopy further confirms that the oxide films dried with the enhanced SD technique are free of pinholes.

14 SOLAR ENERGY↗
DOE OSTI2022

Effect of PVD-coated chromium on the subcooled flow boiling performance of nuclear reactor cladding materials

Here we elucidate the separate effect of a thin Cr coating deposited by physical vapor deposition (PVD) on the subcooled flow boiling performance of zircaloy-4. First, we run flow boiling experiments on prototypical zircaloy-4 surfaces mimicking the scratch pattern and surface roughness of nuclear reactor claddings. Then, we PVD-coat a 0.3 µm thick chromium layer on the same exact surface and repeat the same flow boiling investigations. All experiments are run using deionized water at atmospheric pressure, flowing on a 1 × 3 cm 2 rectangular cross section channel at a rate of 1000 kg/m 2 /s and a subcooling of 10 K. We measure the average temperature of the boiling surface at increasing surface heat fluxes, covering a wide range of heat transfer regimes, from single-phase forced convection to the boiling crisis. We also record high-speed videos of the boiling process, which we postprocess to measure bubble nucleation site density, growth time, departure diameter and frequency. The surface analysis reveals that, while the chromium coating does not seem change the surface roughness and morphology, it improves surface wettability. However, it decreases the critical heat flux. The chromium coating causes an increase of nucleation temperature, bubble departure diameter and growth time, and a reduction of the nucleation site density. The concurrence of these observations indicates that a size reduction of the nucleation sites, conformally covered by the chromium coating, may be the cause of the boiling performance deterioration. We confirm this hypothesis repeating the same analysis on a FeCrAl sample prepared and tested using the same protocol as the zircaloy-4 sample, but with a different initial surface texture.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Origins of wear-induced tungsten corrosion defects in semiconductor manufacturing during tungsten chemical mechanical polishing

During chemical mechanical polishing (CMP) process optimization, a unique corrosion defect was identified in the tungsten (W) contact plugs, which were investigated to develop practical solutions to improve CMP mass productivity. The corrosion defect occurred in the absence of external incident energy and was observed to occur only at the W plugs connected to the P + /n-well close to the wafer edge. To examine the root cause of the corrosion, a series of experiments was carried out at each W CMP step, using in-line defect inspection. Additional experiments were conducted using on-line inductively coupled plasma mass spectrometry (ICP-MS) to understand pH- and potential-dependent electrochemical dissolution behaviors of W. Experimentally, W corrosion was confirmed to be exacerbated if the surface oxide of the W plugs is removed by the deionized water (DIW) rinsing step under wafer pressurization, then exposed to DIW and alkaline cleaning solution. Although the DIW rinsing step is commonly performed to clean polishing pads right after the main polishing, a small amount of applied pressure (0.5 psi) without slurry supply can lead to corrosion defects. Finally, this wear-induced corrosion of the W plugs can be prevented by removing the applied pressure during the post DIW rinsing step of W CMP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Mechanical Characterization of Low Modulus Polymer-Modified Calcium-Silicate-Hydrate (C-S-H) Binder

Calcium-silicate-hydrate (C-S-H) represents a key microstructural phase that governs the mechanical properties of concrete at a large scale. Defects in the C-S-H phase are also responsible for the poor ductility and low tensile strength of concrete. Manipulating the microstructure of C-S-H can lead to new cementitious materials with improved structural performance. This paper presents an experimental investigation aiming to characterize a new synthetic polymer-modified synthetic calcium-silicate-hydrate (C-S-H)/styrene-butadiene rubber (SBR) binder. The new C-S-H/SBR binder is produced by calcining calcium carbonate and mixing this with fumed silica (SiO 2 ), deionized water and SBR. Mechanical, physical, chemical and microstructural characterization was conducted to measure the properties of new hardened C-S-H binder. Results from the experimental investigation demonstrate the ability to engineer a new C-S-H binder with low elastic modulus and improved toughness and bond strength by controlling the SBR content and method of C-S-H synthesis. The new binder suggests the possible development of a new family of low-modulus silica-polymer binders that might fit many engineering applications such as cementing oil and gas wells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Dual-Functional Thermocapacitive Heat Pump with Electrochemical Supercapacitors for Building Thermal Management and Energy Storage

Efficient heating and cooling technologies can help reduce the energy consumption and carbon emissions of buildings. This work explores the use of supercapacitive cells in a multifunctional, liquid-regenerated thermocapacitive heat pump that can provide electrical energy storage in addition to heating and cooling. A proof-of-concept prototype based on eight commercial supercapacitors and using deionized water as a liquid regenerator demonstrated cooling and energy storage capabilities. A peak cooling coefficient of performance (COPc) of 0.27 was achieved at a temperature drop of 0.24 K. The highest measured electrical energy storage density of the cells was 5.93 J cm-3, and the highest cooling power delivered relative to the volume of the cells was 0.58 mW cm-3. This work demonstrates the use of electrochemical energy storage devices in multifunctional equipment for thermal management in buildings.

25 ENERGY STORAGE↗
DOE OSTI2021

On the influence of test speed and environment in the fatigue life of small diameter nitinol and stainless steel wire

Here, to better understand the complex interplay of speed and environment on metals commonly used in implants, rotary bend fatigue tests were conducted on stainless steel and nitinol wires. A range of alternating strains was tested to create ε-N curves at two speeds (physiologic and accelerated) and in three environments (deionized water at body temperature, phosphate buffered saline at body temperature, and laboratory air at ambient room temperature). Results indicate that speed and environment can affect the observed fatigue life in nuanced ways. An electropotential monitoring technique was demonstrated to characterize fatigue crack growth which may be useful in future investigations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Immobilization of cesium and iodine into Cs 3 Bi 2 I 9 perovskite-silica composites and core-shell waste forms with high waste loadings and chemical durability

Cs$_3$Bi$_2$I$_9$, a defect perovskite derivative, is a potential host phase to immobilize iodine and cesium with high waste loadings. In this work, two strategies were explored to form Cs$_3$Bi$_2$I$_9$-silica composites and a core-shell structure in order to improve chemical durability of waste form materials meanwhile maintaining high waste loadings. Cs$_3$Bi$_2$I$_9$ loadings as high as 70 wt.% were incorporated into a silica matrix to form silica-ceramic composites, and 20 wt.% Cs$_3$Bi$_2$I$_9$ was encapsulated into silica to form a core–shell structure by low temperature spark plasma sintering. Chemical durability of the composite and core-shell waste forms was evaluated by semi-dynamic leaching experiments, and Cs and I were incongruently released from waste form matrices. A BiOI alteration layer formed, acting as a passivation layer to reduce the release of radionuclides. The long-term iodine release rate was low (30 mg m$^{-2}$ day$^{-1}$) for the 70 wt.%Cs$_3$Bi$_2$I$_9$–silica composite leached in deionized water at 90 °C, which can be further reduced to 5 × 10$^{-3}$ mg m$^{-2}$ day$^{-1}$ for the 20 wt.% core-shell structure. This work highlights a robust way to immobilize the highly mobile radionuclides with high waste loadings through encapsulation into durable matrices and a surface passivating mechanism that can greatly reduce the elemental transport from waste form materials and significantly enhance their chemical durability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Design of non-fluorinated proton exchange membranes from Poly(Terphenyl fluorenyl isatin) with fluorene-linked sulfonate groups and microblock structures

Proton exchange membranes (PEMs) are essential components in energy storage and conversion devices, such as fuel cells and electrolyzers. Here, in this study, we developed a series of non-fluorinated PEMs from poly(terphenyl fluorenyl isatin) with fluorene-pendent disulfonate groups. These polymers feature a microblock structure composed of hydrophobic blocks, hydrophilic blocks, and alternating blocks, arising from the differences in reactivity, concentration, and solubility between the hydrophobic p-terphenyl and hydrophilic disulfonated fluorene monomers. As a result, the sulfonic acid groups are unevenly distributed along the polymer chains, forming densely charged regions (IEC = 3.52 meq/g) with large ion clusters and lightly charged regions (IEC = 2.16 meq/g) with small ion clusters. This microstructure, combined with the degree of sulfonation, significantly influences the overall properties of the membranes, including robust mechanical strength (47.1–63.2 MPa), high thermal stability (up to 270 °C), low swelling ratio (18–25% at 80 °C), and high proton conductivity (136–169 mS/cm in deionized water at 80 °C). The PFLSH60 membrane demonstrated comparable fuel cell performance to Nafion 212. Its hydrogen crossover current density was more than two times lower (0.86 mA/cm 2 for PFLSH60 compared to 1.83 mA/cm 2 for Nafion 212) under testing conditions of 80 °C and 100% RH. This significantly reduced crossover improves fuel utilization in fuel cell stacks. This work offers valuable insights into the design of robust, high-performance PEMs by systematically analyzing the relationships between membrane structure, properties, and performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗